aLIGHT

Overview

This product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The declaration of conformity may be consulted at: https://Kreafunk.com/pages/declaration-of-conformity.

Made from recycled materials.

The device features a USB-C port for charging, indicated as 5V/1A input.

Charging

We recommend that you charge your aLIGHT to 100% before using it the first time. A charging cable is included in the box. The small indicator light will turn red when charging and turn off when fully charged.

Charging status: ? 0-99% (Red), 100% (Indicator Off).

Battery Status

The battery indicator is located on the back of your aLIGHT. When the battery level drops below 10%, it will emit a small sound every 5 minutes.

Battery levels: 0-10% [?], 10-100% [?].

Magnet Feature

A small magnetic plate with double-sided tape is included with your aLIGHT. It can be attached to the bottom, allowing aLIGHT to stick to metal surfaces.

The device can be attached to metal surfaces using the included magnetic plate with double-sided tape.

Basic Operation

Power On/Off

Press and hold the power button located at the bottom of your aLIGHT for 2 seconds to turn the device on or off.

Listen via Bluetooth (Pairing)

Find aLIGHT in your device's Bluetooth list (in settings). When the indicator light is blinking, the device is in Bluetooth pairing mode. The light will be solid blue when connected to aLIGHT.

Manual Bluetooth Pairing

To manually connect the aLIGHT to Bluetooth, press the power button 3 times.

Play/Pause

To play or pause the sound on the aLIGHT, press the power button twice.

Phone Calls

To answer a call, press the power button once.

To reject a call, press and hold the power button for 2 seconds.

To end a call, press the power button once.

Lamp Control

Hold the light button for 2 seconds to turn the lamp on or off.

To adjust the brightness, press the light button once.

Stereo Play (TWS)

Step 1: Activate Stereo Play

To activate Stereo Play, delete your aLIGHT from your device's Bluetooth list. Then, press and hold the power button on both speakers for 2 seconds to turn them on.

Step 2: Pair Speakers

Now press the power button twice on one of the speakers.

Step 3: Connect to Device

Only one aLIGHT should appear in your device's Bluetooth list. If you see two, please try again.

Resetting the aLIGHT

To reset your aLIGHT, first remove it from the Bluetooth list on your device. Then, press and hold the power button for 8 seconds.

Technical Specifications

• 100% recycled GRS plastic
• Water-resistant (IPX5)
• Dimensions: 64*51 mm (Ø*H)
• Weight: 100g
• Speaker: Ø40 mm 40 5W
• Playing time: up to 15 hours
• Light time: up to 15 hours
• Charging time: 2 hours (USB)
• USB-C cable included
• Lamp
• Magnetic
• Stereo Play (TWS)
• Built-in Lithium battery with 3.7V, 400mAh
• Bluetooth: version 5.1
• Range: up to 10 m
• Input power: 5V / 1A
• Frequency band: 2402-2480 MHz
• Maximal radio frequency effect: < 2 dBm

Safety and Maintenance Instructions

1. Please read this operation manual carefully before use.
2. The safety and maintenance instructions in this operation manual should be retained for future reference and must be followed at all times.
3. Keep the product away from heat sources such as radiators, heaters or other appliances that produce heat.
4. Place the speakers in a stable position to avoid fall and cause damage or personal injury.
5. Do not expose the product to direct sunlight for longer periods. High temperatures may shorten the life of the product, destroy the battery and distort certain plastic parts.
6. Do not expose the product to extreme cold as it may damage the internal circuit board.
7. aLIGHT shouldn't be left in your car. Especially not in the sunlight.
8. Do not charge in direct sunlight. aLIGHT can operate and charge from -20 to 60 degrees Celsius.
9. Rechargeable batteries have a limited number of charge cycles. Battery life and number of charge cycles varies by use and settings.
10. Avoid liquids getting into the product.
11. Before wiping with a dry cloth to clean the speakers, set the power switch to the off position and unplug the power cord from the power outlet.
12. Do not throw or stamp on the product. This may damage the internal circuit board.
13. Do not try to disassemble the product. This must only be done by a professional.
14. Do not use concentrated chemical products or detergent to clean the product.
15. Keep the surface away from sharp things, as these may cause damage to the plastic parts.
16. Use 5V / 1A power supplies only. The connection of power supplies with higher voltage may lead to severe damage.
17. Do not arbitrarily discard or place the lithium battery near fire or intense heat in order to avoid a risk of explosion.

If you experience any problems with your product, please contact the retailer you purchased the product from. The retailer will provide you with guidance and if that does not solve the problem, the retailer will handle the claim directly with Kreafunk.

Certifications and Compliance

The product complies with various certifications including CE, FCC, UKCA, KC, and RoHS. It is made with recycled materials and adheres to responsible forestry standards (FSC).

FCC ID: 2ACVC-ALIGHT