Kreafunk Karl Bluetooth Speaker

Introduction

Welcome to the user manual for the Kreafunk Karl Bluetooth speaker. This stylish product is made from 100% recycled plastic.

This product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The declaration of conformity may be consulted at: https://Kreafunk.com/pages/declaration-of-conformity

Charging

Charge your product to 100% before using it the first time.

Battery Status Indicators:

• ? Orange: 0-99%
• ? Green: 100%
• ? Red: 0-10%
• ⚪️ White: 10-100%

Charging is done via USB-C with a 5V/2A input, supporting up to 5W.

Listen via Bluetooth

Step 1: Power on the speaker. The LED will be flashing white.

Step 2: On your device, go to Bluetooth settings. Select 'Karl' from the list of available devices. The LED will stop flashing white and turn off, indicating a successful connection.

Manual Bluetooth Pairing

Step 1: Power on the speaker. The LED will be flashing white.

Step 2: On your device, go to Bluetooth settings. Select 'Karl' from the list of available devices. The LED will stop flashing white and turn off.

Connect with NFC

To connect using NFC, bring your NFC-enabled smartphone close to the speaker.

A prompt will appear on your phone asking to connect to Karl. Select 'yes' to establish the connection.

Playback Controls

Play/Pause: [double tap] the power button.

Change Volume: [single tap] the volume up or down buttons.

Change Track: [single tap] the previous or next track buttons.

Phone Calls & Voice Assistant

Answer/End Call: [single tap] the power button.

Activate Voice Assistant: [triple tap] the power button.

Stereo Play (TWS)

Before starting: Remove 'Karl' from your Bluetooth list on your device.

Step 1: Power on both speakers. Ensure the LED on both speakers is flashing white.

Step 2: On one speaker (Speaker 1), [single tap] the power button. The LED will turn blue.

Step 3: On your device, enable Bluetooth and select 'Karl'. The LED on both speakers will turn off, indicating they are paired in TWS mode.

To turn off TWS: [single tap] the power button on either speaker.

Resetting the Device

Before resetting: Remove 'Karl' from your Bluetooth list on your device.

[Five taps] the power button. The LED will flash white, indicating the device has been reset.

Technical Specifications

• 100% recycled GRS plastic
• 100% recycled polyester (fabric)
• Water-resistant (IPX5) ?
• Dimensions: 85*103 mm (Ø*H)
• Weight: 360g
• Speaker: 15W
• DSP (digital signal processor)
• Playing time: up to 30 hours
• Charging time: 2-3 hours (USB) / 5-6 hours (Qi)
• Supports wireless charging ⚡️
• USB-C cable included ?
• Stereo Play (TWS)
• NFC connection (compatible with Android) ?
• Voice Assistant ?
• Build in Lithium battery with 3.7V, 4000mAh
• Bluetooth: version 5.1 ?
• Range: up to 10 m
• Input power: 5V / 2A
• Frequency band: 2402-2480 MHz
• Maximal radio frequency effect: <3 dBm

Safety and Maintenance Instructions

• Please read this operation manual carefully before use.
• Retain the safety and maintenance instructions for future reference and follow them at all times.
• Keep the product away from heat sources like radiators or heaters.
• Place speakers in a stable position to avoid falls and damage.
• Do not expose the product to direct sunlight for extended periods, as high temperatures can shorten its lifespan, damage the battery, and distort plastic parts.
• Do not expose the product to extreme cold, as it may damage the internal circuit board.
• Do not leave Karl in your car, especially in direct sunlight.
• Do not charge in direct sunlight. Karl operates and charges between -20 to 60 degrees Celsius.
• Rechargeable batteries have a limited number of charge cycles. Battery life and cycle count vary with usage and settings.
• Avoid liquids getting into the product.
• Before cleaning with a dry cloth, turn the power switch to OFF and unplug the power cord.
• Do not throw or stamp on the product, as this may damage the internal circuit board.
• Do not attempt to disassemble the product; this should only be done by a professional.
• Do not use concentrated chemical products or detergents for cleaning.
• Keep the surface away from sharp objects that could damage plastic parts.
• Use only 5V/2A power supplies. Using higher voltage power supplies may cause severe damage.
• Do not discard or place the lithium battery near fire or intense heat to avoid explosion risk.
• If you experience any problems, contact the retailer you purchased the product from.

Regulatory Information

FCC Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Important: Changes or modifications not authorized by the manufacturer could void the user's authority to operate the product.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

FCC ID: 2ACVC-KARL

Contact Information

Kreafunk ApS
Klamsagervej 35A, st.
8230 Aabyhoej
Denmark
Website: www.Kreafunk.com
Email: info@Kreafunk.dk
Phone: +45 96 99 00 20