Kreafunk aGO 2
Bluetooth Speaker
User Manual
Overview
The Kreafunk aGO 2 is a portable Bluetooth speaker designed for wireless audio playback.
Key features and indicators:
- Information: ?
- Play/Pause: ▶️/⏸️
- Track Control: ⏭️ (Next) / ⏮️ (Previous)
- Volume Control: ? (Up) / ? (Down)
- Bluetooth Connectivity: ?
- Power Button: ?
- Microphone: ? (for Voice Assistant)
- Charging Port: USB-C (5V/1A) ?
Charging the Speaker
Charging Indicator: The small indicator light shows the charging status:
- Orange: 0-99% charged
- Green: 100% charged
We recommend charging your aGO 2 to 100% before first use. A charging cable is included in the box. The indicator light turns orange while charging and green when fully charged.
Battery Status
The battery indicator is located on top of the aGO 2. It lights up white when the speaker is turned on. The small light turns red when the battery level drops below 10%.
- Red: 0-10% battery
- White: 10-100% battery
Powering On/Off
To Turn On: Press the power button ? located on the side of your aGO 2. The indicator light will start blinking white.
To Turn Off Stereo Play (TWS): Press the power button five times.
Connecting via Bluetooth
Pairing Mode: Ensure the indicator light is blinking white (refer to the 'Powering On/Off' section).
Connecting to Your Device:
- On your device, navigate to Bluetooth settings.
- Find "aGO 2" in the list of available devices.
- Select "aGO 2" to connect. The indicator light will turn solid white when successfully connected.
Manual Bluetooth Pairing: To manually initiate Bluetooth pairing, press and hold the power button ? for 2 seconds until the indicator light flashes white.
Audio Playback Controls
Play/Pause: To play or pause the audio, press the power button ? twice.
Change Track: To skip to the next track, press and hold the '+' button for 2 seconds. To go to the previous track, press and hold the '-' button for 2 seconds.
Adjust Volume: To increase volume, press the '+' button once. To decrease volume, press the '-' button once.
Phone Calls
To Answer or End a Call: Press the power button ? once.
To Reject a Call: Press and hold the power button ? for 2 seconds.
Voice Assistant
To activate your device's voice assistant (e.g., Siri or Google Assistant), press the power button ? three times.
Stereo Play (TWS)
Pairing Two Speakers
Preparation: Before pairing two speakers for Stereo Play, remove any existing "aGO 2" connection from your device's Bluetooth list.
Initiate Pairing: On both speakers, press the power button ? once.
Connecting Speakers
Connecting: On the first speaker, press and hold the power button ? until you hear a sound. While still holding the power button, press the '+' button once. Then, release both buttons. The indicator light will turn purple.
Connecting to Device
Final Connection: On your device, connect to "aGO 2" via Bluetooth. Ensure only one "aGO 2" is visible in your Bluetooth list. If two are visible, an error occurred; try again.
The indicator light will turn solid white when successfully connected in Stereo Play mode.
Turning Off Stereo Play
To disable Stereo Play and return to single-speaker mode, press the power button ? five times.
Resetting the aGO 2
To reset the aGO 2 to its factory settings, first remove it from your Bluetooth list. Then, press and hold the power button ? for 8 seconds.
Technical Specifications
- 100% recycled ABS plastic
- Water-resistant (IPX5)
- Dimensions: 80*39 mm (Ø*H)
- Weight: 180g
- Speaker: Ø53 mm, 4Ω 6W
- Playing time: Up to 10 hours
- Charging time: 2-3 hours
- USB-C cable included
- Stereo Play (TWS) support
- Built-in Lithium battery: 3.7V, 1000mAh
- Bluetooth version: 5.1
- Range: Up to 10 meters
Electrical Specifications
- Input power: 5V / 1A
- Frequency band: 2402-2480 MHz
- Maximal radio frequency effect: <3 dBm
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Important: Changes or modifications to this product not authorized could void the FCC compliance and negate your authority to operate the product.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
FCC ID: 2ACVC-AGOII
Safety and Maintenance Instructions
- Please read this operation manual carefully before use.
- The safety and maintenance instructions in this operation manual should be retained for future reference and must be followed at all times.
- Keep the product away from heat sources such as radiators, heaters or other appliances that produce heat.
- Place the speakers in a stable position to avoid fall and cause damage or personal injury.
- Do not expose the product to direct sunlight for longer periods. High temperatures may shorten the life of the product, destroy the battery and distort certain plastic parts.
- Do not expose the product to extreme cold as it may damage the internal circuit board.
- The aGO 2 shouldn't be left in your car. Especially not in the sunlight.
- Do not charge in direct sunlight. The aGO 2 can operate and charge from -20 to 60 degrees Celsius.
- Rechargeable batteries have a limited number of charge cycles. Battery life and number of charge cycles varies by use and settings.
- Avoid liquids getting into the product.
- Before wiping with a dry cloth to clean the speakers, set the power switch to the off position and unplug the power cord from the power outlet.
- Do not throw or stamp on the product. This may damage the internal circuit board.
- Do not try to disassemble the product. This must only be done by a professional.
- Do not use concentrated chemical products or detergent to clean the product.
- Keep the surface away from sharp things, as these may cause damage to the plastic parts.
- Use 5V / 1A power supplies only. The connection of power supplies with higher voltage may lead to severe damage.
- Do not arbitrarily discard or place the lithium battery near fire or intense heat in order to avoid a risk of explosion.
If you experience any problems with your product, please contact the retailer you purchased the product from. The retailer will provide you with guidance and if that does not solve the problem, the retailer will handle the claim directly with Kreafunk.
Contact Information
Kreafunk ApS
Karupvej 6
8000 Aarhus C
Denmark
Website: www.Kreafunk.com
Email: info@Kreafunk.dk
Phone: +45 96 99 00 20
