Hamron Jump Starter 4-in-1

Product Description

The Hamron Jump Starter 4-in-1 is a versatile device designed to start vehicles with 12V electrical systems, power most 12V appliances up to 15A, charge mobile phones via a USB port, and inflate tires and footballs using its built-in compressor.

Intended Use

This product is intended for starting vehicles and boats with 12V electrical systems. It can also power various 12V appliances and charge portable electronic devices via the USB port. The integrated compressor is designed for inflating tires, sports equipment, and similar items.

Symbols on the Product

Please read all instructions and safety information carefully before use.

• WARNING! Electrical Hazard: Indicates a risk of electric shock.
• WARNING! Corrosive Substance: The product contains corrosive substances.
• CE Marking: Indicates compliance with applicable EU directives and regulations.
• Recycling Symbol: Dispose of the product as electrical/electronic waste.

Product Overview

1. Battery charge indicator
2. USB power outlet, 5V DC
3. USB/battery check button
4. Work light switch
5. Power switch
6. Status indicator for correct/incorrect connection
7. Work light
8. 12V DC power outlet
9. Pressure gauge
10. Compressor switch
11. Charger connection

Safety Instructions

WARNING! Failure to follow these instructions can result in death or personal injury.

IMPORTANT! Failure to follow these instructions can result in damage to the product, other property, or the surrounding area.

Note: Information that is necessary in a given situation.

Safety Instructions for Operation

WARNING! Failure to follow these instructions can result in death or personal injury.

• Read and understand the instructions before using the product.
• Save these instructions and safety instructions for future reference.
• Do not use the product for purposes other than its intended use. The manufacturer is not liable for damage resulting from improper use.
• Wear safety glasses. If battery fluid gets into your eyes, rinse them with clean water for at least 10 minutes and seek immediate medical attention.
• Keep the product away from moisture, water, or other liquids.
• Keep the product away from direct sunlight.
• Do not use the product if parts are missing. Contact the retailer if parts are missing.
• Do not use the product if it is damaged or defective. Contact an authorized service center.
• Do not allow persons without adequate experience, knowledge, or training to operate the product without supervision.
• Do not attempt to repair the product. Damaged or defective products must be repaired by an authorized service center. The manufacturer is not liable for damage resulting from unauthorized repairs.
• Use only the supplied battery charger.
• Ensure that the connection clamps cannot be short-circuited.
• Connect the clamps to the battery with the correct polarity.
• Start vehicles outdoors or in a well-ventilated area.
• Only use the product with vehicles equipped with a 12V electrical system.
• Do not use the product as a substitute for the vehicle's own battery.
• Store the product in a dry, enclosed space, inaccessible to children, when not in use.
• Ensure all product switches are in the OFF position when the product is not in use.
• Ensure all product switches are in the OFF position before cleaning or maintenance.
• Clean the product regularly.
• Dispose of the product in accordance with local regulations.

Operation

Checking the Battery

1. Briefly press the USB/battery check button. The battery charge indicator will show one of the following:
   • Green flashing light with alarm: Battery voltage is too high. Ensure the product is charging correctly.
   • Green flashing light (no alarm): The product is charged and ready for use.
   • Solid yellow light: The product's battery needs charging.
   • Solid red light: The product's battery needs charging as soon as possible.
   • Red flashing light with alarm: Battery voltage is too low. The product's battery needs charging.
   • Red flashing light, alarm, and automatic shutdown: Battery voltage is too low. The product's battery needs charging.
2. Press the USB/battery check button again to avoid unnecessary charging.

Charging the Battery

Note! Fully charge the product's battery before first use.

1. Connect the charger plug to a power outlet.
2. Connect the charger to the product. The three battery charge indicator lights will flash sequentially while the battery is charging. The green light illuminates when the battery is fully charged.

Note! It typically takes 6-40 hours to fully charge the battery, depending on its condition.

3. When the battery is fully charged, disconnect the charger from the product and unplug the charger from the power outlet.

Note! For optimal performance and battery life, keep the battery fully charged. Battery life will be shortened if the battery remains discharged for extended periods.

Note! The product's battery can also be charged from a vehicle's 12V outlet, but a full charge cannot be achieved this way.

Note! Always charge the product's battery after each use.

Using the Jump Start Function

WARNING! Only start vehicles with a 12V electrical system with this product.

1. Check the product's battery. Charge if necessary.
2. Turn off all electrical equipment and lights in the vehicle.
3. Connect the red positive (+) clamp to the vehicle battery's positive (+) terminal.
4. Ensure the red positive (+) clamp makes good contact with the battery's positive (+) terminal.
5. Connect the black negative (-) clamp to the battery's negative (-) terminal. The green status light will illuminate when the connection is good.

WARNING! Do not connect the black negative (-) clamp before the red positive (+) clamp is connected to the battery's positive (+) terminal.

Note! If it's not possible to connect to the vehicle battery's negative (-) terminal, connect the black negative (-) clamp to the vehicle's metal chassis.

6. Set the power switch to the ON position.
7. Turn the vehicle's ignition key to the start position. If the engine does not start, wait at least 3 minutes before trying again.

IMPORTANT! Do not operate the starter motor for more than 5 seconds.

8. Turn the power switch OFF once the vehicle's engine has started.
9. Disconnect the black negative (-) clamp.
10. Disconnect the red positive (+) clamp.
11. Recharge the product's battery after use.

Using the Compressor

1. Connect the compressor air hose to the object to be inflated.

Note! Use an adapter if necessary.

2. Set the compressor switch to the ON position.

IMPORTANT! Do not operate the compressor for more than 10 minutes at a time. Allow the product to cool down for at least 10 minutes before using the compressor again.

3. Set the compressor switch to the middle position when the pressure gauge indicates the desired pressure has been reached.
4. Disconnect the hose from the object.
5. Recharge the product's battery after use.

Using the Work Light

1. Press and hold the light switch button for 3 seconds. The work light turns on.
2. Press the light switch button again. The work light flashes.
3. Press the light switch button again to turn off the work light.

Note! The work light automatically turns off if the battery voltage becomes too low.

4. Recharge the product's battery after use.

Using the 12V DC Outlet

1. Open the cover of the 12V DC outlet.
2. Connect the equipment that needs to be powered.

Note! The maximum output power for the 12V DC outlet is 200W. The outlet is equipped with overload protection with automatic reset.

Maintenance

Cleaning the Product

• Clean the product with a damp cloth after operation.

Storage

Storing the Product

• Recharge the product's battery every 3 months during storage.

Disposal

Disposing of the Product

• Dispose of the product in accordance with applicable regulations. Do not burn the product.

Technical Data