Yaheetech Bed Frame Assembly Instructions
Model Number: 601293
Important Information
General Advice:
- We recommend 2 or more people to install.
- The expected assembly time is 0.5 hours.
- Not intended for use by children.
- Keep away from fire or other heat sources.
- We recommend wearing protective gloves.
Assembly Precautions:
Please follow the instruction manuals and use a pad to avoid damage during assembly. Ensure the product and floor are protected during installation.
Parts List
| Part | Description | Quantity |
|---|---|---|
| 1 | Long Rod | x2 |
| 2 | Long Rod | x2 |
| 3 | Short Rod with holes | x2 |
| 4 | Side Rail | x2 |
| 5 | Side Rail | x2 |
| 6 | Side Rail | x2 |
| 7 | Headboard Support | x1 |
| 8 | Headboard Support | x1 |
| 9 | Headboard Support | x1 |
| 10 | Slats | x8 |
| A | M8*65mm Screw | x4 |
| B | M6*50mm Screw | x8 |
| C | M6*35mm Screw | x12 |
| D | M6*15mm Screw | x4 |
| E | Washer | x12 |
| F | Nut | x4 |
| G | Connector | x4 |
| H | Allen Wrench | x1 |
Assembly Steps
-
Attach part 1 (x2) and part 8 (x1) to part B (x4) and part E (x4) using screws and washers as shown. Partially tighten screws.
Diagram Description: Shows two long rods (1) and one headboard support (8) being connected to the frame using screws (B) and washers (E). The diagram indicates to partially tighten the screws.
-
Attach part 2 (x2) and part 9 (x1) to part B (x4) and part E (x4) using screws and washers as shown. Partially tighten screws.
Diagram Description: Shows two long rods (2) and one headboard support (9) being connected to the frame using screws (B) and washers (E). The diagram indicates to partially tighten the screws.
-
Connect side rails (4, 5, 6) using screws (C, D) and nuts (F) as illustrated. Partially tighten screws.
Diagram Description: Shows side rails (4, 5, 6) being attached to the frame structure using screws (C, D) and nuts (F). The diagram emphasizes partial tightening of screws.
-
Attach the assembled side rails to the main frame using screws (C) and washers (E) as shown. Partially tighten screws.
Diagram Description: Illustrates the connection of the side rails to the main bed frame using screws (C) and washers (E). Partial tightening is indicated.
-
Attach headboard supports (A) and connectors (G) using screws (A, E) and washers (E) as shown. Partially tighten screws.
Diagram Description: Shows the headboard supports (A) and connectors (G) being attached to the frame using screws (A) and washers (E). Partial tightening is recommended.
-
Insert the slats (10) into the designated slots on the frame. Ensure all slats are securely in place.
Diagram Description: Shows the slats (10) being inserted into the bed frame. Arrows indicate the direction of insertion.
Final Tightening: After all screws are set, fully tighten them using the provided Allen wrench (H).
Customer Support
If you are not entirely satisfied with your purchase, please follow these steps:
- Go to Your Orders.
- Find your order in the list.
- Select Problem with order.
- Choose your topic from the list displayed.
- Select Contact seller.
Manufacturer Information:
Manufactured in PRC for Yahee GmbH
Importer: Yahee GmbH
Hans-Grüninger-Weg 11
71706 Markgröningen
You can also download the electronic Installation Manual from the Product guides and documents section of the advertising page.
