Yaheetech Metal Queen Bed Frame Assembly Instructions
Model # 611085
Important Information
⚠️ Please follow the instruction manuals and use a pad to protect the product during your assembly.
For easier and better assembly, 2 or more adults are required. ?
The expected assembly time for this product is approximately 1 hour, depending on the individual's manipulative ability. ⏳
Safety Precautions
- This product is not intended for children to climb. Please keep your children from climbing this product. ❌
- Do not place the product near fire or heat sources! Caution: Fire Hazard! ?
- Do not use corrosive cleaners for cleaning! ?
- Be careful of your hands when setting up! We recommend wearing protective gloves for assembly. ?
- Please check the number and condition of the parts according to the parts list. If any parts are damaged or missing, please contact us immediately.
- We recommend checking the tightness of all connections between parts every six months. ⚙️
- The warnings, cautions, and instructions listed in this manual may not cover all possible situations that may arise when using the product. Please contact Yaheetech via e-mail info@yahee.com.cn if you need further information or help.
Parts List
Please verify all parts are present before assembly. If any parts are damaged or missing, contact Yaheetech.
- (1) x1: Long metal support bar
- (2) x1: Long metal support bar
- (3) x1: Long metal support bar
- (4) x3: Short metal support bar
- (5) x3: Short metal support bar
- (6) x1: Metal slat
- (7) x1: Metal slat
- (8) x1: Metal slat
- (9) x1: Metal slat
- (10) x2: Metal slat
- (11) x1: Headboard/Footboard component
- (12) x1: Headboard/Footboard component
- (13) x1: Headboard/Footboard component
- (14) x2: Metal slat
- (15) x1: Metal slat
- (16) x2: Metal slat
- (A) x22: Screw
- (B) x23: Screw
- (C) x6: Screw
- (D) x1: Allen wrench ?
- (17) x12: Rubber plug
Assembly Instructions
General Note: During assembly, please first half-tighten all screws into the holes. After all screws are set, fully tighten them. It is recommended to have 2 or more people for assembly. ?
Step 1
Attach component (1) to the side rail using screws (A) and (B). Part (2) and (3) are similarly attached. The diagram shows the correct orientation and screw insertion points.
Diagram Description: Shows the initial connection of the main frame components. Part (1) is attached to a side rail using screws (A) and (B). Parts (2) and (3) are similarly attached. The diagram highlights the use of specific screws and the half-tightening instruction.
Step 2
Connect shorter support bars (4) and (5) to the main side rails. Attach slats (6), (7), (8), (9), and (10) to the frame. Various screws (A, B, C) are used for these connections.
Diagram Description: Illustrates the assembly of the bed frame's base structure. Shorter support bars (4, 5) are attached to the main side rails. Slats (6, 7, 8, 9, 10) are also shown being positioned. Various screws (A, B, C) are used for these connections.
Step 3
Attach headboard/footboard uprights (11), (12), and (13) to the main frame. Use screws (A) and slats (10) for these connections as shown in the diagram.
Diagram Description: Depicts the attachment of the headboard or footboard uprights (11, 12, 13) to the main frame. Screws (A) and slats (10) are shown being used in this step.
Step 4
Install the remaining bed slats (6), (7), (8), (9), and (10) across the frame. Secure these using screws (A), (B), and (C) as indicated in the diagram.
Diagram Description: Shows the installation of more bed slats across the frame, secured with screws (A, B, C). This step likely completes the slat installation.
Step 5
Attach the headboard structure to the side rails. Use screws (A) and (B) along with components (11) and (12) to secure the headboard posts to the main frame.
Diagram Description: Illustrates the final attachment of the headboard structure to the side rails using screws (A, B) and components (11, 12). The diagram shows the headboard posts being secured to the main frame.
Step 6
Install the central support beam (14) and additional slats (15), (16). Secure these to the frame using screws (A) and (B).
Diagram Description: Shows the installation of the central support beam (14) and additional slats (15, 16). These are secured to the frame using screws (A, B).
Step 7
Insert the central support leg (17) into the central support beam. The diagram shows the leg being pushed into place for added stability.
Diagram Description: Illustrates the insertion of the adjustable central support leg (17) into the central support beam for added stability.
Step 8
Attach the rubber plugs (17) to the ends of the side rails. Distinguish between left (L) and right (R) plugs and install them on the corresponding side rails as marked.
Diagram Description: Shows the rubber plugs (17) being fitted onto the ends of the side rails. The diagram emphasizes distinguishing between left (L) and right (R) plugs and installing them on the corresponding side rails.
Conclusion
Thank you for purchasing a Yaheetech product!
At Yaheetech, we are dedicated to bringing you the best online shopping experience and making your life comfortable. We pride ourselves on an integrated supply chain team that works meticulously to deliver you products and service with greatest value. Our networks span across the US, the United Kingdom, Germany, France and six more European countries. It is always our belief that how customers view our business and service ultimately defines our brand.
So, how did we do? Please let us know by making an online remark about it.
Good job. Would you like to share your experience to assist others with their shopping decisions?
Not good. Can you give us a chance to fix the problem?
You can also get a downloadable user manual by visiting: www.yaheeshop.com/pdf/en-1-6011363.pdf
