Philips Dynalite DUS360CS-D Multifunction Sensor
Installation Instructions
Also available in: Instructions d'installation, Installationsanweisungen, Instrucciones de instalación, Istruzioni per l'installazione, Installatie-instructies, インストール手順, 安装指示, إرشادات التركيب
Important Safety Information
⚠️ Devices must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.
Multilingual notes:
- French: Les appareils doivent être installés par un électricien diplômé conformément à tous les codes et réglementations électriques et de construction nationaux et locaux.
- German: Die Geräte sind von einem qualifizierten Elektriker in Übereinstimmung mit allen geltenden Vorschriften zu installieren.
- Spanish: Los dispositivos deben ser instalados por un electricista calificado y cumpliendo todas las normas y regulaciones, tanto nacionales como locales, sobre instalaciones eléctricas y obras.
- Italian: I dispositivi devono essere installati da un elettricista qualificato in conformità con le norme locali e nazionali vigenti in materia di costruzioni edilizie e installazione di impianti elettrici.
- Dutch: De apparaten moeten worden aangebracht door een gekwalificeerde elektricien en in overeenstemming met alle nationale en plaatselijke elektriciteits- en bouwvoorschriften.
- Japanese: 装置を取り付ける際は、資格のある電気技師に依頼し、国および地域の電気および建設に関するすべての法令に従ってください。
- Chinese: 根据国家/地区及当地的电气与建筑规范和法规,该设备必须由有资质的电工进行安装。
- Arabic: يجب تركيب الأجهزة من قبل فني كهربائي مؤهل وفقًا لكافة قوانين ولوائح التركيب الكهربائي المحلي والوطني.
Product Overview
The Philips Dynalite DUS360CS-D is a multifunction sensor designed for lighting control systems.
Dimensions:
- Height: 46 mm (1.82 in)
- Diameter: 105 mm (4.13 in)
Installation Steps
Step 1A: PIR Sensor Placement
This step involves positioning the PIR sensor. The diagram shows the sensor with its dimensions.
Diagram shows the sensor with dimensions 46 mm (1.82 in) height and 105 mm (4.13 in) diameter.
Step 1B: PIR Detection Angle
The Passive Infrared (PIR) sensor has a detection angle of 120°.
Diagram illustrates the 120° detection angle of the PIR sensor.
Step 2: PIR Detection Coverage and Environment
The PIR sensor provides coverage up to 5.5 meters (18 ft) with a minimum detection range of 2 meters (6.5 ft).
Recommended mounting height is between 2.1 to 4.0 meters (6.9 to 13.1 ft).
The sensor operates within environmental limits:
- Temperature: 0° C to 45° C (32° F to 113° F)
- Humidity: Less than 90%
- Note: For a 7.0 meter (23 ft) detection range, the ambient temperature should be ≤ 25° C (77° F).
Diagram shows the PIR detection pattern, coverage range, recommended mounting height, and environmental operating conditions.
Step 3: Protective Earth (PE) Connection
Ensure proper grounding. The diagram illustrates placement relative to a floor lamp and desk, with an 80° field of view indicated.
Diagram shows the sensor's position and an 80° detection angle, implying its placement in a room.
Step 4: Infrared (IR) Detection
The sensor also includes Infrared (IR) detection with a 120° angle. This is typically used for remote control signals.
Diagram illustrates a person using a remote control, indicating the IR detection range.
Step 5: Wiring and Electrical Specifications
DALI Wiring:
- Wire Gauge: Less than 1 mm² (16+ AWG)
- Torque: 0.4 Nm (3.5 Lb-in)
- DALI Bus Voltage (ELV): 9.5 - 22.5 V
- DALI Bus Current: 9 mA
- DALI Insulation: Basic
⚠️ DALI wires are NOT SELV and should never be considered touch safe.
IEC Overvoltage Category: III
Diagram shows wire connections, wire gauge, torque specifications, and DALI electrical parameters.
Step 6: Mounting the Sensor Body
Secure the sensor body to the mounting surface.
- Torque: 0.5 Nm (4.4 Lb-in)
- Mounting Hole Diameter: Ø6.5 mm (0.26 in)
- Mounting Screw Size: 4.5 mm (0.18 in)
Diagram illustrates the process of attaching the sensor to a ceiling or wall mount, showing screw placement and torque.
Step 7A: Cable Entry Preparation
Prepare the cable entry point on the mounting surface.
- Cable Entry Hole Diameter: Ø64 mm (2.51 in)
- Cable Diameter Range: 3 - 25 mm (0.12 - 0.98 in)
Diagram shows the required hole size for cable entry and the range of acceptable cable diameters.
Step 7B & 7C: Final Assembly
Complete the sensor assembly by attaching the cover and routing cables.
- Outer Diameter: 89 mm (3.5 in)
- Internal component dimensions shown: 70 mm (2.75 in), 60 mm (2.36 in), 50 mm (1.96 in).
Diagrams illustrate the final steps of attaching the sensor cover and securing it, with cable management.
Step 8: System Connection Diagram
This diagram shows how the DUS360CS-D sensor connects to a DALI controller (e.g., DDBC120-DALI, DDBC320-DALI) and subsequently controls lighting fixtures via the DALI protocol.
Diagram shows a simplified wiring schematic: Sensor -> DALI Controller -> Light Bulb.
Step 9: Labeling and Planning
The final step involves labeling the sensor, typically with barcodes, for system planning and inventory management.
Diagram shows a hand scanning a barcode label on the sensor and a planning sheet with similar labels.
Regulatory and Legal Information
Electrical Safety: Do not connect inputs to mains. DALI wires are NOT SELV and should never be considered touch safe.
Refer to the Service Guide for full cleaning recommendations.
Federal Communications Commission (FCC) Compliance Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by reorienting or relocating the receiving antenna, increasing separation between the equipment and receiver, or connecting the equipment to a different circuit. Any modifications not approved by the manufacturer could void the user's authority to operate this device.
Canadian Compliance: This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B).
Installation Standards: Installation of a home and building automation and control system shall comply with IEC 60364 (all parts). The temperature limits and current-carrying capacities for the communication wires specified in IEC 60364-5-52 shall not be exceeded.
© 2022 Signify Holding. All rights reserved. Specifications are subject to change without notice. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.
Website: www.dynalite.com
Document Reference: AZZ 490 0922 R19
