DEWALT DCR008 Rechargeable Mini Bluetooth Speaker

Product Components

Refer to the diagrams for component identification:

• 1: Power button (⏻)
• 2: Volume up button (+)
• 3: Volume down button (-)
• 4: Bluetooth® status indicator LED (?)
• 5: Play/Pause button (▶️/⏸️)
• 6: Bluetooth® button (?)
• 7: Carry strap
• 8: Charging cable
• 9: Charger plug
• 10: Charging plug
• 11: Charging port cover
• 12: Charge indicator LED (?)
• 13: Charging port

Safety Information

General Warnings

WARNING: Read all safety warnings and instructions. Failure to follow may result in electric shock, fire, or serious injury.

WARNING: To reduce the risk of injury, read the instruction manual.

Intended Use

The DEWALT DCR008 Bluetooth® speaker is designed to play/stream audio wirelessly from a mobile phone or other audio device. Do not use under wet conditions or near flammable liquids or gases. Keep out of reach of children; supervision is required for inexperienced operators.

Safety Alert Symbols and Words

This manual uses symbols and words to alert you to hazards:

• DANGER: Imminent hazard, will result in death or serious injury if not avoided.
• WARNING: Potentially hazardous situation, could result in death or serious injury if not avoided.
• CAUTION: Potentially hazardous situation, may result in minor or moderate injury if not avoided.
• [Information symbol]: Safety-related message.
• NOTICE: Practice not related to personal injury, may result in property damage if not avoided.

Important Safety Instructions

Follow these instructions:

• Read and keep instructions.
• Heed all warnings.
• Do not use near water.
• Clean only with a dry cloth.
• Do not block ventilation openings.
• Keep away from heat sources.
• Protect the charging cord from damage (pinching, walking on).
• Use only manufacturer-specified attachments/accessories.
• Unplug during lightning storms or when unused for long periods.
• Refer servicing to qualified personnel.
• Do not expose to dripping or splashing; do not place liquids on the unit.
• Do not use under wet conditions or near flammable liquids or gases.
• Do not keep ears close to the appliance.

Safety Instructions for Speakers

• Do not expose to rain or moisture to prevent fire or electric shock.
• Do not abuse the charging cord; never carry the speaker by it, pull the cord to disconnect, or expose it to heat, oil, or sharp edges.
• Switch off the speaker when unattended, not in use, changing accessories, or servicing.
• This appliance is not for use by persons with reduced physical/sensory/mental capabilities or lack of experience unless supervised.
• Supervise children to ensure they do not play with the appliance.
• Keep open flame sources (like candles) away from the speaker.
• To reduce hearing damage risk, do not place ears too close to the speaker.

Additional Safety Information

WARNING: Never modify the speaker or any part of it, as this could result in damage or personal injury.

The speaker label may include symbols: V (volts), Hz (hertz), min (minutes), DC (direct current), Class I Construction (grounded), OPM (oscillations per minute), RPM (revolutions per minute), sfpm (surface feet per minute), /min (per minute), SPM (strokes per minute), BPM (beats per minute), A (amperes), IPM (impacts per minute), W (watts), Wh (watt hours), Ah (amp hours), AC (alternating current), AC/DC (alternating or direct current), Class II Construction (double insulated), no load speed, rated speed, PSI (pounds per square inch), earthing terminal, safety alert symbol, do not stare into light, wear respiratory protection, wear eye protection, wear hearing protection, read all documentation, do not expose to rain.

Batteries and Charging

Battery Information

The product is not fully charged upon purchase. Read safety instructions before charging. If unused for 90 days, fully charge the battery to prolong its life.

Important Safety Instructions for All Integral Battery Charging

WARNING: Follow all battery, charging cable, and product warnings. Failure to do so may result in electric shock, fire, or serious injury.

WARNING: Use only certified power adapters compliant with applicable regulations and safety standards. Use only the supplied DEWALT charging cable. The cable is for DEWALT tools only; using it for other tools may cause battery overheating or bursting.

• Do not expose the charging cable to water, rain, or snow.
• Disconnect by pulling the plugs, not the cord.
• Ensure the cord is not stepped on or tripped over.
• Do not use a damaged charging cable or plugs; replace them immediately.
• Keep conductive foreign materials away from charging plugs and ports.
• Always unplug the charging cable when not in use.

Charging Procedure (Fig. A, B)

1. Pull the charging port cover (11) away from the speaker.
2. Insert the charging plug (10) into the charging port (13).
3. Plug the charger plug (9) into a power source (e.g., computer, wall adapter). Note: Charging takes approximately two hours with a 5V, 1A supply.
4. The charge indicator LED (12) is red and continuously lit while charging.
5. Charging is complete when the charge indicator LED (12) turns green and stays continuously lit. The battery can remain connected or the USB cable can be disconnected.

Hot/Cold Delay

The speaker suspends charging if the battery is too hot or too cold until it reaches an appropriate temperature (40°F to 104°F / 4°C to 40°C) to ensure maximum battery life. During this delay, the charge indicator LED (12) will not illuminate. Charging resumes when the temperature is within range, indicated by a blinking LED (12).

Important Charging Notes

• The speaker may become warm during charging; this is normal.
• If the speaker does not charge properly, take it and the USB cable to a local service center.
• You can charge a partially used battery without adverse effects.

Over Temperature Protection

If over temperature protection is activated, the charge indicator LED (12) will turn off. The unit can still be used during this cycle.

Checking State of Charge

When the speaker is powered ON, press the power button (1). The speaker will announce the remaining battery percentage. Note: This is an estimate and may vary based on components, temperature, and usage.

Operation

Button Functions (Fig. A)

Power Button

Press and hold the power button (1) to turn the speaker on or off. When on, press the power button (1) to hear the battery charge percentage.

Play/Pause Button

When connected via Bluetooth®:

• Press the play/pause button (5) to play or pause audio.
• Press twice quickly to advance to the next track.
• Press three times quickly to skip to the previous track.

Volume Adjustment Buttons

Use the volume buttons (2, 3) to increase or decrease volume. A quick press adjusts by one level; a long press adjusts continuously.

Playing Audio

Audio can be played wirelessly via a Bluetooth® connection to a compatible device.

Pairing Speaker with a Bluetooth® Audio Device (Fig. A)

1. Place the speaker and Bluetooth® device within 3 ft. (1 m) of each other.
2. Turn on the speaker by pressing the power button (1).
3. Ensure Bluetooth® is enabled on your audio device (consult device manual for instructions).
4. Press the Bluetooth® button (6) on the speaker.
5. The blue Bluetooth® status indicator (4) will flash twice, indicating pairing mode.
6. Select "DEWALT DCR008" on your device and confirm pairing.
7. Once paired, the Bluetooth® status indicator (4) will remain solid blue.
8. Audio will now play from your device. Note: Audio output power is 1x5W.

Bluetooth® Status Indicator

Connecting a Previously Paired Bluetooth® Audio Device

If a device was previously paired, it should reconnect automatically when the speaker is powered on. Ensure Bluetooth® is enabled on the device. If connection fails, follow the pairing instructions.

Stereo Pairing with Two Speakers

1. On both speakers, simultaneously press and hold the Bluetooth® button (6) for three seconds.
2. Speakers will announce "left channel" and "right channel" upon successful pairing.
3. The Bluetooth® status indicator (4) will be solid blue on the left channel speaker and unlit on the right channel speaker.

Timeout Functionality

To conserve battery, the speaker powers off automatically after fifteen minutes of inactivity (e.g., unpaired or Bluetooth® connection lost). Refer to "Connecting a Previously Paired Bluetooth® Audio Device" if this occurs.

Bluetooth® Range

Optimum range is approximately 30 ft. (9 m) with a clear line of sight, but up to 100 ft. (30 m) is possible. Obstacles and other wireless devices may affect connection quality. If connection is lost, reconnect your device.

Incoming Call

If your phone receives a call while connected, the Bluetooth® connection will pause. When the call ends, the speaker will automatically switch back to the Bluetooth® connection.

Maintenance

Cleaning

WARNING: Never use solvents or harsh chemicals on plastic parts, as they can weaken the material. Use only a dry cloth. Do not allow liquid inside the tool or immerse any part in liquid.

Accessories

WARNING: Use only DEWALT recommended accessories. Using unapproved accessories could be hazardous. Recommended accessories are available from DEWALT dealers or service centers. Contact DEWALT at 1-800-4-DEWALT or www.dewalt.com for assistance.

Repairs

The speaker and charging cable are not serviceable and contain no user-serviceable parts. WARNING: For safety and reliability, all repairs, maintenance, and adjustments must be performed by a DEWALT factory service center or an authorized service center using identical replacement parts.

Warranty and Registration

Register Online

Register your product at www.dewalt.com for:

• Warranty Service: Efficient service in case of product issues.
• Proof of Ownership: For insurance purposes (fire, flood, theft).
• Safety Notifications: To be contacted if a safety notification is required.

Three Year Limited Warranty

For warranty terms, visit https://www.dewalt.com/support/warranty. To request a written copy, contact Customer Service at DEWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286 or call 1-800-4-DEWALT (1-800-433-9258).

Latin America: Warranty terms may differ. Consult country-specific information.

Free Warning Label Replacement

If warning labels are illegible or missing, call 1-800-4-DEWALT (1-800-433-9258) for a free replacement.

Company Information

DEWALT Industrial Tool Co. 701 East Joppa Road, Towson, MD 21286

Copyright © 2022

Trademarks include the DEWALT yellow and black color scheme, the "D" shaped air intake grill, the handgrip pyramid array, the kit box configuration, and the lozenge-shaped humps on the tool surface.