JOBSITE PRO-X1 TRUE WIRELESS EARBUDS WITH CHARGING CASE

Instruction Manual

⚠ WARNING: TO REDUCE THE RISK OF INJURY, USER MUST READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT

SAVE THESE INSTRUCTIONS

Thank you for purchasing the Jobsite Pro-X1 True Wireless Earbuds with Charging Case.

With this wireless headset, users can:

• Enjoy convenient wireless hands-free calls
• Control wireless music
• Switch between calls and music

Package Contents

• True Wireless Earbuds - left and right
• Charging case
• Type C charging cable
• Earbud cushions - 8 sets of cushions
• User manual

COMPONENTS AT A GLANCE

DEFINITIONS: SAFETY GUIDELINES

The definitions below describe the level of severity for each signal word. Users should read the manual and pay attention to these symbols.

⚠ DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

⚠ WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

GETTING STARTED

CHARGE THE CASE

Connect the Type C end of the USB cable into the charging case, and USB A end into the power source.

• Charging process is indicated by the white LED light on the front panel.
• When the charging case is fully charged, the white light stays on.

CHARGE EARBUDS

• Place the earbuds in the charging case. The earbuds will start charging.

PAIR THE EARBUDS WITH YOUR BLUETOOTH DEVICE

Take both earbuds from the charging case; the earbuds will power on automatically, entering pairing mode.

• When taking out both earbuds, a voice will announce, “POWER ON - Battery HIGH (or battery medium or battery low)-Pairing”. Following this, two “DOO-DOO” sounds indicate both earbuds are connecting to the Bluetooth device. If unable to connect to a previously playing device, it will take 5-10 seconds, and the earbuds will flash red and blue. The earbud is now in pairing mode and will voice “PAIRING” from both earbuds.
• Turn on the Bluetooth function of the Bluetooth device and pair the earbuds with the Bluetooth device.
• When successfully connected to a phone or other Bluetooth device, the Blue LED will stay on for 1 second, then a voice will announce, “Your device is connected".

THE FOLLOWING DIRECTIONS SHOW HOW TO PAIR THE EARBUDS WITH YOUR BLUETOOTH DEVICE

Turn on the Bluetooth function of the Bluetooth device, select DEWALT TWS 209A. Enter the earbuds password “0000” if prompted. For Bluetooth devices featuring Bluetooth 3.0 or higher, no password is needed.

SINGLE EARBUD PAIRING (MONO MODE)

Take either earbud from the charging case; the earpiece will power on automatically. Search for DEWALT TWS 209A and tap to connect. Once pairing has succeeded, a voice will announce "Your device is connected” and the indicator light will be off.

PAIR THE EARBUDS WITH ANOTHER BLUETOOTH DEVICE

If users have another Bluetooth device they want to pair with the earbuds, ensure the Bluetooth function in any other previously paired or connected devices is turned off. Then follow the steps in "Pair the earbuds” with the Bluetooth device for the first time.

CONNECT THE EARBUDS TO YOUR BLUETOOTH DEVICE

Turn on the Bluetooth function of the Bluetooth device. Take both earbuds from the charging case; the earbuds will power on and reconnect automatically. If no device is connected, the earbuds will automatically turn off after 2 minutes. Both earbuds are now powered on and are paired with each other automatically. The earbuds will search for the previously connected Bluetooth device and reconnect to it automatically. If the last connected one is not available, the earbuds will search and reconnect to the next most recently connected device.

CONTROLS

• To turn earbuds ON: remove from the charging case. Earbuds automatically power on.
• To turn earbuds OFF: place back in charging case and close cover. The first and fourth LED on the charging case will stay on for 5 seconds. This indicates the earbuds are off and are charging.

MANAGE YOUR CALLS AND MUSIC:

• To play or pause music: Press the Multi-Function button once (left or right)

1. Multi-Function button
2. Forward (next song): Press V+ for 2 seconds. Volume increase: press V+
3. Backward (previous song): Press V- for 2 seconds. Volume decrease: press V-

CALL CONTROL

USE THE MULTI-FUNCTION BUTTON

• Answer/Hang up: Press the multi-function button once (left or right)
• Reject incoming call: Press the multi-function button (left or right) and hold for 1 second
• Switch caller during call: Press the multi-function button (left or right) twice
• Voice Control - Siri/Google: Press the multi-function button twice (left or right)

LED INDICATOR - EARBUDS

• Earbuds are powered on: The Red and Blue LED flashes for 1 second.
• Earbuds are pairing to a Bluetooth device: The Red and Blue LED flashes alternately.
• Earbuds are connected to a Bluetooth device: The Blue LED stays on for 1 second.
• Earbuds are powered on and connected to a Bluetooth device: The Red and Blue LED flashes. If no connection can be made, the headset will power itself off after 2 minutes.

LED Indicator lights (Earbuds)

• Low battery level: The Red LED will flash 3 times every 2 seconds and a voice will announce, "Battery Low”, every 100 seconds.
• Battery is fully charged: The LED is off.

Earbuds feature an IPX6 rating for protection against sweat and water.

LED INDICATOR - CHARGING CASE

Close the charging case cover for earbuds to charge. The first and fourth LED will stay on for 5 seconds.

• 4 White LED lights = 75-100% power
• 3 White LED lights = 50-75% power
• 2 White LED lights = 25-50% power
• 1 White LED light = 0-25% power

LED INDICATOR - CHARGE CASE WITH EARBUDS INSIDE

While charging the case, White LED status:

• 3 White LED lights stay on and the 4th LED flashes every second for 75-100% power
• 2 White LED lights stay on and the 3rd LED flashes every second for 50-75% power
• 1 White LED light stays on and the 2nd LED flashes every second for 25-50% power
• 1 White LED light flashes every second for 0-25% power

FACTORY RESET

1. If earbuds were previously paired, be sure to "Forget this device" or 'Unpair' (DEWALT TWS 209A) in the Bluetooth device's "paired devices” list before resetting.
2. Place earbuds into the charging case and keep case open.
3. Press the factory reset button twice. This will disconnect the earbuds from any paired devices and reset them to factory setting.
4. To pair again immediately after resetting, go to the device's Bluetooth setting and select “DEWALT TWS 209A”.

TECHNICAL DATA - EARBUDS

• Music time: Up to 7.5 hours per charge (up to 30 hours total with charging case)
• Talk time: Up to 6 hours per charge (up to 24 hours total with charging case)
• Standby time: 220 hours
• Charging time: 1.5 hours
• Rechargeable Li-ion battery: 55mAh on each earpiece
• Bluetooth version: 5.0
• Compatible Bluetooth profiles: HFP / HSP / A2DP / AVRCP
• Supported audio codec: SBC
• Frequency band: 2.4 GHz ISM Band
• Transmitter power: ≤ 4 dBm
• Operating range: 10 meters (33 feet)

TECHNICAL DATA - CHARGING CASE

• Charging time: 2 hours
• Rechargeable Li-ion battery: 500mAh

IMPORTANT SAFETY INSTRUCTIONS FOR ALL RECHARGEABLE BATTERY PACKAGING

The battery is not fully charged out of the carton. Before using the earbuds, read the safety instructions below and then follow the charging procedures outlined.

Do not incinerate the battery module even if it is severely damaged or is completely worn out. The battery can explode in a fire. Toxic fumes and materials are created when lithium batteries are burned. If battery contents come into contact with the skin, immediately wash the area with mild soap and water. If battery liquid gets into the eye, rinse eyes with water for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts. Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention. These earbuds are splash and water resistant and were tested under controlled laboratory conditions with a rating of IPX6 under IEC standard 60529. Splash and water resistance are not permanent conditions and resistance might decrease as a result of normal wear. Do not attempt to charge wet earbuds; to dry earbuds, tap them gently against a hand with the port cover open to remove excess liquid. Leave the power bank in a dry area with some airflow. Placing earbuds in front of a fan blowing cool air directly onto the earbuds might help the drying process. The charge case does not have an IP rating. Liquid damage is not covered under warranty.

⚠ WARNING: DO NOT leave earbuds or charge case in any location with excessive heat.

⚠ WARNING: DO NOT charge or use the battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.

⚠ WARNING: DO NOT modify the battery in any way to fit a non-compatible charger as the battery may rupture causing serious personal injury.

⚠ WARNING: DO NOT splash or immerse in water or other liquids.

⚠ WARNING: DO NOT store or use the earbuds in locations where the temperature may reach or exceed 105° F (40° C) (such as outside sheds or metal buildings in summer). For best life, store earphones in a cool, dry location. The True Wireless Earbuds should not be disposed of as municipal solid waste. To recycle them, contact a local hazardous waste processor or contact Call 2 Recycle® on their website, call2recycle.org, or by phone at 877-273-2925 to find the nearest drop-off location for lithium-polymer batteries.

⚠ WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

⚠ WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If the battery pack is cracked or damaged, do not insert the charging cable. Do not crush, drop or damage the battery. Do not use the earphones if they have received a sharp blow, been dropped, run over or damaged in any way (e.g. pierced with a nail, hit with a hammer, stepped on).

STORAGE RECOMMENDATIONS

1. The best storage place is one that is cool and dry, away from direct sunlight and excessive heat or cold.
2. For long storage, it is recommended to store the earphones in a cool dry place for optimal results.

Damaged batteries should be returned to a service center for recycling.

LIMITED LIFETIME WARRANTY

DEWALT is available to assist. If users are not satisfied with this product or have questions on how to use it, DEWALT should be contacted directly. Users DO NOT NEED TO CONTACT THE RETAILER. Contact one of DEWALT's service representatives using the contact information listed below. Please provide the product number when contacting DEWALT.

PLEASE CALL CUSTOMER SERVICE:

888-480-9885, 8:00 a.m.-5:00 p.m. PT, Monday - Friday,

or e-mail DEWALT using: dewaltinfo@efilliate.com

E-filliate Inc.
11321 White Rock Road
Rancho Cordova, CA 95742 USA

FCC Compliance Information

Part No. DXMA1902092 © 2022 Stanley Black & Decker, Inc.

FCC ID: 2ADH6-190209LB
FCC ID: 2ADH6-190209RB
DID: D047300

DEWALT® and the DEWALT Logo are trademarks of the DEWALT Industrial Tool Co., or an affiliate thereof and are used under license. The yellow/black color scheme is a trademark for DEWALT power tools & accessories.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications made to this device not expressly approved by E-filliate Incorporated may void the FCC authorization to operate this device. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

RF exposure statement: The device compliance RF exposure requirement and can be installed and used without restriction.