DEWALT Jobsite Pro Wireless Earphones

Model: DXMA1902091

Introduction

Thank you for purchasing the Jobsite Pro Wireless Earphones. These earphones allow the user to listen to audio wirelessly from up to 33 feet (approximately 10 meters) from a paired phone or tablet. Ensure the earphones are fully charged before first use. Refer to the "Charging Procedure" section for instructions.

Safety Guidelines and Warnings

The following definitions describe the level of severity for each signal word:

⚠ DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
⚠ WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
⚠ CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
ℹ NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

General Warning: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

Jobsite Pro Wireless Earphones Safety Warnings

This manual contains important safety and operating instructions. Read this manual and all labels on the earphones before use.
Before using, read all instructions and cautionary markings.
Shock hazard: Do not allow any liquid to get inside the earphones. Electric shock may result.
The earphones are rated IPX6 and have been tested to withstand powerful water jets for up to 1 minute. They are not designed to be submerged underwater.
When operating outdoors, always provide a dry location.
Do not operate if the earphones have received a sharp blow, been dropped, run over, or otherwise damaged.
Do not disassemble the earphones; there are no user-serviceable parts.

Important Safety Instructions for All Rechargeable Batteries

The battery is not fully charged out of the carton. Before using the earphones, read the safety instructions below and follow the charging procedures.

READ ALL INSTRUCTIONS

Do not incinerate the battery module, even if severely damaged or worn out, as it can explode in a fire, creating toxic fumes and materials.
If battery contents come into contact with skin, immediately wash the area with mild soap and water. If battery liquid gets into the eye, rinse with water for 15 minutes or until irritation ceases. Seek medical attention if needed. Battery electrolyte is a mixture of liquid organic carbonates and lithium salts.
Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention.
Do not charge or use the battery in explosive atmospheres (e.g., presence of flammable liquids, gases, or dust).
DO NOT modify the battery to fit a non-compatible charger, as it may rupture and cause serious personal injury.
DO NOT splash or immerse in water or other liquids.
Do not store or use earphones where temperatures may reach or exceed 105°F (40°C) (e.g., outside sheds or metal buildings in summer). For best life, store earphones in a cool, dry location.
Jobsite Pro Wireless Earphones should not be disposed of as municipal solid waste. Contact your local hazardous waste processor or Call 2 Recycle® (call2recycle.org, 877-273-2925) for nearest drop-off locations for lithium-polymer batteries.

Battery Warnings

⚠ WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.
⚠ WARNING: Fire hazard. Never attempt to open the battery pack. If the battery pack is cracked or damaged, do not insert the charging cable. Do not crush, drop, or damage the battery. Do not use earphones if they have received a sharp blow, been dropped, run over, or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped on). Damaged batteries should be returned to a service center for recycling.
⚠ WARNING: Shock hazard. Do not allow any liquid to get inside the earphones. Electric shock may result.
⚠ WARNING: Burn hazard. Do not submerge the earphones in any liquid or allow any liquid to enter. Never attempt to open the earphones. If the plastic housing breaks or cracks, return it to a service center for recycling.

Charging Procedure

Charge the wireless earphones by connecting a TYPE C power-in cable to the earphones' charging port.
Plug the USB connector into a USB port on any computer or USB power adapter.
When charging, a red light on the controller will illuminate. Once the light turns blue, the earphones are fully charged.
When the battery is empty, it will take up to two hours to fully charge them.

Important Charging Notes

For longest life and best performance, charge the device when the air temperature is between 65°F and 75°F (18° – 24°C). DO NOT charge in air temperatures below +40°F (+4.5°C) or above +105°F (+40.5°C). This is important to prevent serious damage.
The earphones may become warm to the touch while charging; this is normal and does not indicate a problem. To facilitate cooling after use, avoid placing earphones in warm environments (e.g., metal sheds, uninsulated trailers).
If earphones do not charge properly:
- a. Check receptacle operation by plugging in a lamp or other appliance.
- b. Verify the receptacle is connected to a light switch that turns power off when lights are turned off.
- c. Move earphones to a location where ambient air temperature is approximately 65°F-75°F (18°C-24°C).
Do not freeze or immerse the earphones in water or any other liquid.

Pairing Procedure

During pairing, place the earphones within one meter of your phone or tablet.
Power on the earphones by pressing and holding the ⌚ (power/multi-function) key on the controller until the indicator light alternately flashes blue and red. Voice prompts will indicate pairing mode is enabled.
Enable the Bluetooth function of your phone or tablet, search for Bluetooth devices, and select "DEWALT 2091" for pairing and connection.
After successful pairing, the blue light on the earphones will blink slowly. Voice prompts will confirm successful pairing. Pairing mode is maintained for three minutes. If pairing fails after two minutes, the headset will automatically switch to standby mode.
Once pairing is complete, the earphones and your phone or tablet will recognize each other automatically.
To remove the pairing connection, go to your phone or tablet's Bluetooth settings, select "DEWALT 2091", and choose the "Forget" option.

Note: Jobsite Pro Wireless Earphones can pair with a maximum of 2 devices. If you experience difficulty pairing a new device, remove a pairing connection from an existing device.

Controller Functions

On/Off: Press and hold the ⌚ key to turn on/off.
Pause/Play: Press the ⌚ key to pause playback, and press again to resume playback.
Volume Increase: Tap the + key.
Volume Reduction: Tap the - key.
Note on Volume Keys: Pressing and holding the - key will restart the current song/audio file from the beginning. Pressing and holding the + key will advance to the next track.
Advance Track: Press and hold the + key to move forward to the next track.
Return Track: Press and hold the - key to go back to the previous track.
Answer/Hang Up: Press the ⌚ key for two seconds and then release it.

Storage Recommendations

The best storage place is cool and dry, away from direct sunlight and extreme heat or cold.
For long storage, store earphones in a cool, dry place for optimal results.

Warranty & Customer Service

Lifetime Limited Warranty

In case of product failure, E-filliate Inc. will issue a replacement. DO NOT RETURN PRODUCT TO STORE. Instead, call 888-480-9885, 8:00 a.m.-5:00 p.m. PT, Monday - Friday, or email dewaltinfo@efilliate.com. Products improperly used, abused, or altered are not covered under policy.

Customer Service

If you have a problem with this product or questions on how to use it, contact E-filliate Inc. You do not need to contact the retailer. Please contact a service representative before shipping merchandise. Provide the product number, DXMA1902091, when contacting us.

Manufacturer Address: E-filliate Inc., 11321 White Rock Rd., Rancho Cordova, CA 95742 USA.

FCC and RF Exposure Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications made to this device not expressly approved by E-filliate Incorporated may void the FCC authorization to operate this device. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.

RF exposure statement: The transmitter must not be colocated or operated in conjunction with any other antenna or transmitter. This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. The installation and use of this product are not restricted.

	DEWALT Jobsite Wireless Earphones DXMA1909935 User Manual User manual for DEWALT Jobsite Wireless Earphones (DXMA1909935), providing detailed instructions on safety, operation, charging, pairing, and warranty.
	DEWALT Jobsite Pro Wireless Earphones Instruction Manual Comprehensive instruction manual for DEWALT DXMA1902091A Jobsite Pro Wireless Earphones, covering safety guidelines, charging, pairing, controller functions, storage, warranty, and FCC compliance.
	DeWALT Jobsite Pro Wireless Earphones Safety Recall Safety recall notice for DeWALT Jobsite Pro Wireless Earphones due to overheating hazard. Affected models and contact information for free replacement are provided.
	DEWALT Jobsite Pro Max Neckband Earphones with Speakers - User Guide Information on DEWALT Jobsite Pro Max Neckband Earphones with Speakers, including features, benefits, and warranty information.
	DEWALT Bluetooth Neckband Earphones Agent Authorization by E-filliate Incorporated Agent Authorization document from E-filliate Incorporated for DEWALT Bluetooth Neckband Earphones, authorizing MiCOM Labs Inc. for certification processes. Includes product details and contact information.
	DEWALT Jobsite Pro-X2 ANC True Wireless Earbuds with Charging Case - Instruction Manual Comprehensive instruction manual for the DEWALT Jobsite Pro-X2 ANC True Wireless Earbuds with Charging Case (Model DXMA1902097). Learn about product features, package contents, component identification, getting started, pairing, controls, volume adjustment, call management, LED indicators, factory reset, technical data, safety instructions, storage recommendations, and warranty information.
	DEWALT Jobsite Pro-X1 True Wireless Earbuds Instruction Manual Comprehensive instruction manual for DEWALT Jobsite Pro-X1 True Wireless Earbuds with Charging Case, covering setup, controls, safety, and technical specifications.
	DEWALT Bluetooth Neckband Earphones - EUT Constructional Details Detailed photographs and constructional overview of DEWALT Bluetooth Neckband Earphones (Model: 1902091B, 2ADH6-1902091B), as presented in a CTI test report.