DEWALT Jobsite Pro-X2 ANC True Wireless Earbuds with Charging Case

Introduction

Thank you for purchasing the DEWALT Jobsite Pro-X2 ANC True Wireless Earbuds With Charging Case. This product allows you to enjoy convenient hands-free calls, control wireless music, and switch between calls and music.

WARNING: TO REDUCE THE RISK OF INJURY, USER MUST READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT.

SAVE THESE INSTRUCTIONS

Package Contents

• 1. True Wireless Earbuds - Left and Right
• 2. Charging Case
• 3. Type C Charging Cable
• 4. Earbud Cushions - 8 Sets
• 5. User Manual

Components at a Glance

True Wireless Earbuds:

• 1. In-Ear Smart Sensor
• 2. LED Indicator
• 3. Multi-Function Button (On/Off/Pause)
• 4. Dial Control (Volume + / Volume -)
• 5. Microphone (2)

Charging Case:

• 1. Battery-Level LED Indicator
• 2. Reset Button
• 3. Type C Charge Port
• 4. Carabiner Loop

Earbud Cushions:

• 8 Sets of Cushions

Charging Cable:

• Type C to Type C Cable

Getting Started

Charge the Case

Connect one Type C end of the Type C cable into the charging case, and the other Type C end into the power source.

• Charging process is indicated by the white LED light on the side panel.
• When the charging case is fully charged, the white light stays on.

Charge Earbuds

• Place the earbuds in the charging case. The earbuds will start charging.

Pair the Earbuds with Your Bluetooth Device

Take both earbuds from the charging case. They will power on automatically and enter pairing mode. You will hear a voice prompt: "BATTERY HIGH/MEDIUM/LOW". If unable to connect to the previous device after 5-10 seconds, the earbuds will flash red and blue, indicating pairing mode. You will hear "PAIRING" from both earbuds.

• Turn on the Bluetooth function of your Bluetooth device and select "DEWALT TWS PRO". Enter the password "0000" if prompted. For devices with Bluetooth 3.0 or higher, a password is not required.
• When successfully connected, the blue LED will stay on for 1 second, and you will hear "CONNECTED".

Single Earbud Pairing (Mono Mode)

Take either earbud from the charging case. It will power on automatically. Search for "DEWALT TWS PRO" and select it to connect. Once paired successfully, you will hear "CONNECTED" and the indicator light will turn off.

Pair the Earbuds with Another Bluetooth Device

To pair with a different Bluetooth device, ensure the Bluetooth function on any previously paired or connected devices is turned off. Then, follow the steps in "Pair the Earbuds with Your Bluetooth Device".

Connect the Earbuds to Your Bluetooth Device

Turn on the Bluetooth function of your Bluetooth device. Take both earbuds from the charging case; they will power on and reconnect automatically. If the last connected device is unavailable, the earbuds will search for and reconnect to the next most recently connected device. If no devices are connected, the earbuds will turn off automatically after 2 minutes.

Note: The Jobsite Pro-X2 ANC True Wireless Earbuds can pair with a maximum of 2 devices. If you experience difficulty pairing a new device, remove a pairing connection from an existing device.

Controls

To Turn Earbuds ON:

• If earbuds are in the charging case: Remove from charging case; earbuds automatically power on.
• If earbuds are not in the charging case & are in off state: Press either multi-function button for 2 seconds.

To Turn Earbuds OFF:

• Place back in charging case and close cover, or press and hold multi-function button for 5 seconds (left or right).

Manage Your Calls and Music

To play music:

• Press the multi-function button once (left or right) or put on earbuds.

To pause music:

• Press the multi-function button once (left or right) or take off earbuds.

EQ Mode:

• Long press the left multi-function button to toggle EQ setting (Music, Podcast, Movie, Super Bass). Default EQ is set to Music mode. EQ mode switch is not applicable in single earbud mono mode.

ANC Mode:

• Long press the right multi-function button to toggle setting (Transparency mode, Noise Cancellation ON, Noise Cancellation OFF). Default is Noise Cancellation OFF. ANC mode switch is not applicable in single earbud mono mode.

Volume Adjustment

Volume Increase:

• Turn RIGHT forward (clockwise) OR turn LEFT forward (counterclockwise).

Volume Decrease:

• Turn RIGHT backward (counterclockwise) OR turn LEFT backward (clockwise).

Multi-Function Button

• Forward (next song): Double click the multi-function button (right).
• Backward (previous song): Double click the multi-function button (left).

Call Control

Use the Multi-Function Button

Answer/Hang up:

• Press the multi-function button once (left or right).

Reject incoming call:

• Press the multi-function button (left or right) and hold for 1 second.

Switch caller during call:

• Press the multi-function button (left or right) twice.

Voice Control - Siri/Google:

• Press the multi-function button (left or right) three times in non-playing state.

LED Indicator - Earbuds

• Earbuds are powered on: The red and blue LED flash for 1 second.
• Earbuds are pairing to a Bluetooth device: The red and blue LED flash alternately.
• Earbuds are connected to a Bluetooth device: The blue LED stays on for 1 second.
• Earbuds are powered on and connected to a Bluetooth device: The red and blue LED flash. If no connection can be made, the earbuds will power off after 2 minutes.

LED Indicator Lights

Low battery level:

• The red LED will flash 3 times every 2 seconds and will voice, "Battery Low".

Battery is fully charged:

• The LED is off.

LED Indicator - Charging Case

Both Earbuds and Charging case feature an IP54 rating for protection against dust and water.

When the earbuds are placed into the charging case for charging, the first and fourth LEDs will stay on for 5 seconds.

When the charging case is open, the LED indicators will display the battery level of the charging case:

• 4 White LED lights = 75-100% power
• 3 White LED lights = 50-75% power
• 2 White LED lights = 25-50% power
• 1 White LED lights = 0-25% power

LED Indicator - Charge Case with Earbuds Inside

While charging the case, White LED status:

• 3 White LED lights stay on and the 4th LED blinks for 75-100% power
• 2 White LED lights stay on and the 3rd LED blinks for 50-75% power
• 1 White LED light stays on and the 2nd LED blinks for 25-50% power
• 1 White LED light blinks for 0-25% power

Factory Reset

1. If your earbuds were previously paired, be sure to "Forget this device" or 'Unpair' (DEWALT TWS PRO) in your Bluetooth device's "paired devices" list before resetting.
2. Place earbuds into the charging case and keep case open.
3. Press the reset button twice or press and hold reset button for 3 seconds. This will disconnect the earbuds from any paired devices and reset them to factory setting.
4. To pair again immediately after resetting, go to your device's Bluetooth setting and select "DEWALT TWS PRO".

Technical Data - Earbuds

• Music time (With ANC OFF): Up to 10 hours per charge (up to 40 hours total with charging case)
• Talk time: Up to 8 hours per charge (up to 32 hours total with charging case)
• Standby time: 220 hours
• Charging time: 1.5 hours
• Rechargeable Li-ion battery: 65mAh on each earpiece
• Bluetooth version: 5.3
• Compatible Bluetooth profiles: HFP / HSP / A2DP / AVRCP
• Supported audio codec: SBC
• Frequency band: 2.4 GHz ISM Band
• Transmitter power: ≤ 4 dBm
• Operating range: 10 meters (33 feet)

Technical Data - Charging Case

• Charging time: 1.5 hours
• Rechargeable Li-ion battery: 550mAh

Important Safety Instructions for All Rechargeable Battery Packaging

The battery is not fully charged out of the carton. Before using the earbuds, read the safety instructions below and follow the charging procedures outlined.

WARNING: Do not incinerate the battery module even if it is severely damaged or completely worn out. The battery can explode in a fire. Toxic fumes and materials are created when lithium batteries are burned. If battery contents come into contact with the skin, immediately wash the area with mild soap and water. If battery liquid gets into the eye, rinse the open eye with water for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts. Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention.

These earbuds and case are dust and water resistant and were tested under controlled laboratory conditions with a rating of IP54 under IEC standard 60529. Dust and water resistance are not permanent conditions and resistance might decrease as a result of normal wear. Do not attempt to charge wet earbuds; to dry your earbuds, tap it gently against your hand to remove excess liquid. Leave your earbuds in a dry area with some airflow. Placing your earbuds in front of a fan blowing cool air directly onto the earbuds might help the drying process. Liquid damage is not covered under warranty.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store the earbuds in a cool dry place for optimal results.

WARNING: DO NOT leave earbuds or charge case in any location with excessive heat.

WARNING: DO NOT charge or use the battery in explosive environments, such as in the presence of flammable liquids, gases or dust.

WARNING: DO NOT modify the battery in any way to fit a non-compatible charger as the battery may rupture causing serious personal injury.

WARNING: DO NOT splash or immerse in water or other liquids.

WARNING: DO NOT store or use the earbuds in locations where the temperature may reach or exceed 105° F (40° C) (such as outside sheds or metal buildings in summer). For best life, store earbuds in a cool, dry location. The True Wireless Earbuds should not be disposed of as municipal solid waste. To recycle it, contact your local hazardous waste processor or contact Call 2 Recycle® on their website, call2recycle.org, or by phone at 877-273-2925 to find the nearest drop-off location for lithium-polymer batteries.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If the battery pack is cracked or damaged, do not insert the charging cable. Do not crush, drop or damage the battery. Do not use the earbuds if they have received a sharp blow, been dropped, run over or damaged in any way (e.g. pierced with a nail, hit with a hammer, stepped on).

Damaged batteries should be returned to a service center for recycling.

Limited Lifetime Warranty

DEWALT is here to help. If you are not satisfied with this product or have questions on how to use it, please contact DEWALT customer service. YOU DO NOT NEED TO CONTACT THE RETAILER. Please contact one of DEWALT's service representatives, using the contact info listed below. Please provide the product number when contacting DEWALT.

PLEASE CALL CUSTOMER SERVICE: 888-480-9885, 8:00 a.m. - 5:00p.m. PT, Monday - Friday, or e-mail us using: dewaltinfo@efilliate.com

E-filliate, Inc.
11321 White Rock Road
Rancho Cordova, CA 95742 USA

Federal Communications Commission (FCC) Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications made to this device not expressly approved by E-filliate Incorporated for compliance may void the FCC authorization to operate this device.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

RF Exposure Statement

This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device is installed and operated without restriction.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.