DOD Meatbox Subsynth

Product Overview

The DOD Meatbox Subsynth is an effects pedal designed to add synthesized sub-harmonic and octave tones to your instrument's signal, with controls for shaping the low-frequency content.

Visual Description: The pedal is housed in a red enclosure. It features four control knobs labeled OCTAVE, OUTPUT, SUB, and LOW. It has an INPUT jack, an OUTPUT jack, a FOOTSWITCH, and an LED indicator. The pedal also displays the DOD logo and the product name 'MEATBOX SUBSYNTH'.

Controls

1. OCTAVE: Adjusts the amount of the lower octave added to the signal.
2. OUTPUT: Adjusts the overall output level of the effect.
3. SUB: Adjusts the amount of synthesized sub-harmonic effect added to the signal.
4. LOW: Adjusts the low-frequency content of the overall effect.

WARNING: Start with minimal settings on the OUTPUT and LOW controls and gradually increase their levels to avoid potential speaker damage.

5. INPUT: Connect your instrument here.
6. FOOTSWITCH: Engages and disengages the effect.
7. LED: Illuminates when the effect is engaged.
8. OUTPUT: Connect to the next pedal in your chain or to your amplifier. This output allows for simultaneous transmission of the dry, unprocessed signal (Ring) and the processed signal (Tip) to your amplifier and other effects using a TRS "Y" cable.
   
   • Tip = Octave + Sub
   • Ring = Dry
   • Sleeve = Ground

Using the Meatbox

Most bassists will prefer placing the Meatbox at the beginning of their effects chain. Guitarists may find it better to add effects after distortion or at the end of their effects chain. A typical effects signal chain would consist of distortion effects first, then modulation effects (Chorus, Flanger, Phaser, Tremolo, etc.), and finally time-based effects (Delay and Reverb). Experiment with different effect placements to find your preferred sound.

Specifications

• Input: 1/4" TS Unbalanced - 470 kΩ
• Output: 1/4" TRS Unbalanced - 100 Ω
• Current Draw: 20 mA
• Bypass: True Bypass
• Power: 9VDC alkaline battery (not included) / PS0913DC power adapter (optional)
• Warranty: 1 Year

Compliance and Safety Instructions

General Warnings

CAUTION: RISK OF ELECTRIC SHOCK - DO NOT OPEN ⚠️

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

The following information pertains to product use at low altitudes. Do not use the product above 2000 m (6561 ft) above sea level.

The symbols shown above are internationally accepted warning symbols for potential hazards associated with electrical products. A lightning bolt ⚡ in an equilateral triangle indicates that the unit contains dangerous voltages. An exclamation mark ⚠️ in an equilateral triangle indicates that the user must consult the operating instructions. These symbols warn that there are no user-serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourself. Refer all servicing to qualified service personnel. Opening the enclosure for any reason will void the manufacturer's warranty. Do not allow the unit to get wet. If liquid is spilled on the unit, turn it off immediately and have it serviced. Unplug the unit during thunderstorms to prevent damage.

UK Mains Plug

A mains plug that has had its cord cut off is unsafe and must be disposed of. Never insert an unsafe or cut mains plug into the 13-amp socket. Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from your local retailer. Replacement fuses are rated at 13 amps and MUST be ASTA approved to BS1362.

Product Disposal

If you wish to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation, which requires proper treatment, recovery, and recycling. Households in the 25 EU member states, Switzerland, and Norway can return used electronic products free of charge to designated collection points or to a retailer (if you buy a similar new product). For countries not listed above, please contact your local authorities for the correct disposal method. This will ensure that your discarded product undergoes the necessary treatment, recovery, and recycling, [WEEE symbol] thereby preventing potential negative effects on the environment and human health.

Important Safety Precautions

• READ THESE INSTRUCTIONS.
• KEEP THESE INSTRUCTIONS.
• HEED ALL WARNINGS.
• FOLLOW ALL INSTRUCTIONS.
• DO NOT USE THIS APPARATUS NEAR WATER.
• CLEAN ONLY WITH A DRY CLOTH.
• FOR INDOOR USE ONLY.
• DO NOT BLOCK ANY VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS.

Installation Precautions

• DO NOT INSTALL NEAR ANY HEAT SOURCES, SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.
• USE ONLY ACCESSORIES/ATTACHMENTS SPECIFIED BY THE MANUFACTURER. UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
• Protect the power-supply cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
• Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When an apparatus is used with a cart, use caution and move the apparatus/cart combination to avoid injury from tip-over.
• All servicing should be referred to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
• POWER SWITCH: The power switch used on this unit does NOT interrupt the mains connection.
• MAINS DISCONNECT: The plug must remain readily accessible. In a cabinet installation or where the plug is inaccessible, an all-pole mains disconnect must be incorporated into the building's electrical installation with a contact separation of at least 3 mm on all poles.
• For 240V operation, use the proper supply cord with CSA/UL certification.

Power Cord Safety

WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET WITH A PROTECTIVE EARTH CONNECTION ?.

The wires in the mains lead are coloured in accordance with the following code:

• GREEN AND YELLOW – EARTH
• BLUE – NEUTRAL
• BROWN – LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

• The wire which is coloured GREEN AND YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol ⏚ or coloured GREEN or GREEN AND YELLOW.
• The wire which is coloured BLUE must be connected to the terminal marked with the letter N or coloured BLACK.
• The wire which is coloured BROWN must be connected to the terminal marked with the letter L or coloured RED.

This apparatus may require the use of a different line cord, or attachment plug, or both, depending on the available power source during installation. If the attachment plug has to be replaced, consult a qualified service person who should refer to the table below. The GREEN/YELLOW cord must be connected directly to the apparatus chassis.

Mains Wiring Information

WARNING: IF THE GROUNDING IS REMOVED, CERTAIN FAULT CONDITIONS IN THE UNIT OR THE SYSTEM TO WHICH IT IS CONNECTED MAY CAUSE FULL LINE VOLTAGE TO BE PRESENT BETWEEN THE CHASSIS AND GROUND. IF THE CHASSIS AND GROUND ARE SIMULTANEOUSLY TOUCHED, SERIOUS INJURY OR DEATH MAY RESULT.