Hudson Valley Lighting Barrytown 5606 Installation Instructions

Safety Warnings and Precautions

WARNING/CAUTION:

• Disconnect power before re-lamping or wiring the fixture. Read all instructions completely before starting installation.
• To avoid the risk of fire or shock, the fixture must be installed in compliance with all applicable national and local electrical/building codes. Installation and maintenance should be completed by a licensed electrician or certified factory-trained technician.
• California Proposition 65: This lighting fixture contains chemicals known to the State of California to cause cancer, birth defects, and/or other reproductive harm. Wash hands after use.
• Unpack fixture, parts, and parts bags before discarding the carton. Ensure all parts are found. Inspect the fixture for any damage before installation. Hudson Valley Lighting does not pay or reimburse electrician fees. Fixtures may not be returned once installed. See warranty for exceptions.
• Please clean with a soft, dry cloth only. Do not use cleansers.

ATTENTION PRUDENCE (French):

Débranchez l'alimentation avant de remplir ou de câbler le luminaire. Lisez complètement toutes les instructions avant de commencer l'installation. Pour éviter le risque d'incendie ou d'électrocution, le luminaire doit être installé conformément à tous les codes électriques/de construction nationaux et locaux applicables. L'installation et l'entretien de cet appareil doivent être effectués par un électricien agréé ou un technicien certifié formé en usine. Californie Prop 65 : Cet appareil d'éclairage contient des produits chimiques connus par l'État de Californie pour provoquer le cancer, des maladies congénitales et/ou d'autres dommages à la reproduction. Laver les mains après utilisation. Déballez le luminaire, les pièces et le(s) sac(s) de pièces avant de jeter le carton. Assurez-vous que toutes les pièces sont trouvées. Inspectez le luminaire avant de l'installer pour détecter tout dommage. HVLG ne paie ni ne rembourse les frais d'électricité. Le luminaire ne peut pas être retourné une fois qu'il a été installé. Voir garantie pour les exceptions. Veuillez nettoyer uniquement avec un chiffon doux et sec ! N'utilisez pas de nettoyants.

PRECAUCIÓN ADVERTENCIA (Spanish):

Desconecte la corriente antes de volver a encender o conectar el aparato. Lea todas las instrucciones antes de comenzar la instalación. Para evitar el riesgo de incendio o descarga eléctrica, la instalación debe ser realizada de conformidad con todos los códigos de construcción / eléctricos nacionales y locales aplicables. La instalación y el mantenimiento de esta unidad debe ser realizado por un electricista licenciado o un técnico capacitado por una en fábrica certificadora. California Prop 65: Este aparato de iluminación contiene productos químicos que el estado de California se conoce por causar cáncer, defectos de nacimiento y / u otros daños reproductivos. Lavarse las manos después del uso. Desembala los accesorios, repuestos y bolsa (s) de repuestos. Antes de desechar la caja. Asegúrese de encontrar todas las piezas. Inspeccione el accesorio antes de la instalación por cualquier daño. HVLG no paga ni reembolsa las tarifas del electricista. El accesorio no se puede devolver una vez que se haya instalado. Consulte la garantía para excepciones. ¡Limpie con un paño seco y suave únicamente! No use limpiadores.

Installation Steps

Diagram Description (Page 2): The diagram shows the components for installing the Barrytown 5606 lighting fixture. It illustrates how the mounting plate attaches to the junction box, how the nipple, collar loop, and hex nut are assembled and adjusted. It depicts the chain being fed through the canopy and screw collar, then attached to the collar loop. The safety cable attachment is shown. Finally, it illustrates connecting the wires (ground, neutral, hot) using wire nuts and tape, pushing wires into the box, securing the canopy, installing the bulb, and attaching the glass with a ball nut. Key parts are labeled with letters A through P.

1. Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on a heavy-duty round or octagon junction box rated for a minimum 90lbs. The junction box must be securely mounted to the structure of the building.
2. Remove the SCREW COLLAR (J) from the COLLAR LOOP (F). Fully thread the NIPPLE (E) onto the COLLAR LOOP (F). Thread the HEX NUT (C) onto the NIPPLE (E) then thread the NIPPLE (E) onto the MOUNTING PLATE (A). Adjust the NIPPLE (E) so that the threads of the COLLAR LOOP (F) extends 1/4" beyond the CANOPY (H). Secure using HEX NUT (C).
3. Open the end link of the CHAIN (I) and attach to the FIXTURE ASSEMBLY (K) at the desired height. Slide the SCREW COLLAR (J) and the CANOPY (H) onto the CHAIN (I). Open the link on the other end of the CHAIN (I) then attach unto the COLLAR LOOP (F). Feed the wires through the CHAIN (I), SCREW COLLAR (J), CANOPY (H), COLLAR LOOP (F) & NIPPLE (E) on MOUNTING PLATE (A).
4. Attach the SAFETY CABLE (O) to the building structure or brace using CABLE CLIP (P).
5. Cut off excess wires, and strip the insulation off the end of the leads.
6. Attach the Ground wire (GREEN) to the ground inside the junction box (Generally green or bare copper wire) or the GROUND SCREW (D) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO "HOT" WIRE. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
7. Connect the fixture's SPT Neutral (SPT WIRE WITH NO WRITINGS) wire lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (G). Starting 1" below the fastener, tightly wrap the connection with electrical tape so that the connections seal the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT.
8. Connect the fixture's SPT hot (SPT WITH WRITINGS) wire lead to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
9. Push the wires back into the junction box. Lift up the CANOPY (H) up to the ceiling, and screw the SCREW COLLAR (J) onto the COLLAR LOOP (F).
10. Screw the BULB (L) up into the SOCKET of the FIXTURE ASSEMBLY (K). THIS FIXTURE IS RATED FOR 10 WATT TYPE B LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE.
11. Attach the GLASS (N) onto the FIXTURE ASSEMBLY (K) then secure using BALL NUT (M). (SEE GLASS SCHEDULE PAGE)
12. Restore power to the outlet at the breaker or fuse box.

Parts List

Diagram Description (Page 3): This section details the decorative arms and glass components of the Barrytown 5606 fixture. It shows an overview of the fixture with five distinct arms labeled A through E, each connecting to a central point. Separate diagrams illustrate the assembly of Arms A, B, C, D, and E, showing how specific parts (labeled A, B, C in these sub-diagrams) are attached. These parts A, B, and C correspond to the three types of glass: Large Glass (GLS-5606-A), Medium Glass (GLS-5606-B), and Small Glass (GLS-5606-C), with 33 pieces of each type included.

Glass Schedule