SKINANDE RENGÖRA LAGAN
IKEA
Design and Quality IKEA of Sweden
Safety Information
⚠️ Warning!
Before proceeding with installation, read the safety information in the User Manual.
This document contains important safety information in multiple languages:
- English
- Deutsch
- Français
- Italiano
- Dansk
- Norsk
- Suomi
- Svenska
- Íslensk
- Português
- Español
- Ελληνικά
- Nederlands
- Polski
- Türkçe
- Русский
- Slovenský
- Lietuvių K.
- Česky
- Magyar
- Български
- Română
- Hrvatski
- Srpski
- Slovenščina
- Eesti
- Latviešu
Tools and Parts Required
Tools:
- Tape measure
- Phillips head screwdriver
- Flat head screwdriver
- Drill
- Pliers
- Spirit level
- Scissors
- Gloves
Key Measurement: 8 mm
Parts:
- 8x Screw A
- 4x Screw B
- 2x Screw C
- 1x Screw D (Torx T20)
- 2x Bracket
- 4x Collar
- 2x "Perfect Fit" clamp
- 1x Clamp
- 2x Ø8 mm collar
- 2x Bracket
- 1x Strip (AA-2114340-1)
- 1x Strip
- 3x Strip
- 4x Washer
- 1x Instruction sheet
- 2x "Perfect Fit" clamp
- 1x Nut
- 1x Washer
- Labels for water connection types (FIN, S, N, DK)
Safety Notes for Tool Usage:
- ❌ Do not use a hammer on the material.
- ✔️ Use hammer correctly when required.
- ❓ Ensure all parts are present before starting assembly.
Installation Steps
Step 1: Prepare Mounting Strips
Cut a strip of material. Create three pieces: a middle piece (X) measuring 600 mm, and two end pieces (Y) measuring 75 mm each.
Step 2: Attach Front Strip
Attach the middle piece (X) to the underside of the cabinet top, aligning it with the front edge. Press firmly into place.
Step 3: Attach Side Strips
Attach the two end pieces (Y) to the sides of the cabinet, near the front edge. Press firmly into place.
Step 4: Secure Appliance
Secure the appliance to the cabinet using screws B and D. The diagram shows screws being inserted and tightened.
Step 5: Attach Front Panel/Handle
Attach the front panel or handle using two screws. A "CLICK" sound indicates a secure snap-fit.
Step 6: Install Brackets
Attach mounting brackets to the sides of the cabinet using screws. Two brackets are shown, each secured with screws.
Step 7: Insert Sealing Strips
Insert sealing strips into the sides of the appliance door opening. Push the strips firmly into place.
Step 8: Further Securing
Secure the appliance further using six screws (6x) into pre-drilled holes.
Step 9: Attach Front Door Panel
With assistance from another person, attach the front door panel. Gloves are recommended for handling. Use screws to secure the panel.
Step 10: Level the Appliance
Adjust the appliance's feet to ensure it is level. The diagram shows rotating the feet. Adjustments can be made within a range of approximately 10 mm.
Step 11: Attach Cabinet Side Panel
Attach a panel to the side of the cabinet. Use tape to hold it in position while securing it with screws.
Step 12: Secure Component
Secure a component using two screws.
Step 13: Attach Appliance Brackets
Attach mounting brackets to the appliance using screws A and D.
Step 14: Attach Front Door Panel
Attach the front door panel to the appliance using hinges and screws.
Step 15: Final Front Panel Attachment
Secure the front panel using screws C and D. Ensure "Perfect Fit" clamps are correctly used. A warning icon indicates incorrect attachment.
Step 16: Connect Drain Hose
Connect the drain hose to the appliance and then to the drain pipe. Ensure a secure connection.
Step 17: Position Appliance
Slide the appliance into its final position. Follow the arrows for guidance. Be cautious of pinching fingers or tipping the appliance.
Step 18: Final Leveling
Make final adjustments to the appliance's feet to ensure a 0 mm gap at the top, confirming it is perfectly level.
Step 19: Hose Routing
Route the water inlet and drain hoses correctly. The drain hose must maintain a minimum height of 40 cm from the floor.
Step 20: Water Inlet Connection
Connect the water inlet hose to the faucet. Ensure compatibility with 3/4" or 1/2" connections. The water pressure should be between 0.3-10 bar.
Step 21: Attach Brackets
Attach brackets to the appliance using screws A and D.
Step 22: Attach Front Panel
Attach the front door panel to the appliance using screws A and D.
Step 23: Secure Front Panel
Secure the front panel using screws D.
Step 24: Final Front Panel Attachment
Complete the attachment of the front panel using screws D.
Step 25: Check Alignment
Verify the alignment of the front panel. A checkmark (✔️) indicates correct alignment.
Step 26: Cleaning and Maintenance
Follow these steps for cleaning the appliance:
- Prepare cleaning solution: Use a jug to measure approximately 1000ml of water and add the recommended cleaning agent (e.g., 130ml for a 30-minute cycle, 100ml for a 20-minute cycle, 10ml for a 10-minute cycle).
- Pour the solution into the appliance.
- Run the appliance according to the indicated cycles:
- 3 cycles of 30 minutes with cleaning agent.
- 2 cycles of 20 minutes with cleaning agent.
- 1 cycle of 10 minutes with cleaning agent.
- Flush the system thoroughly with clean water.
- Important: Avoid using cleaning agents directly on seals or certain internal parts as indicated by warning icons.
Door Front Compatibility
This appliance is compatible with various door fronts, including:
- SKINANDE RENGÖRA LAGAN
- VÅGLIG
- VOXTORP
Ensure the door front height does not exceed 800 mm.
