FINPUTSAD RENGÖRA METOD
Installation and Connection Guide
Important Safety Information
⚠️ WARNING: Installation and connection of electrical, water, and gas systems must be performed by a qualified technician. Adhere strictly to the manufacturer's instructions and all applicable local safety regulations.
Tools Required
- Screwdrivers (various types)
- Drill with ⌀2mm bit
- Gloves ?
- Tape measure ?
- Pliers ?
- Scissors ✂️
- Tape ?
Parts Included
The following parts are included with your appliance. Please verify all components are present before commencing installation.
- Part A: Manuals (1x)
- Part B: Base support (1x)
- Part C: Mounting bracket/rail (1x)
- Part D: Mounting brackets (4x)
- Part E: Screws (16x)
- Part F: Screws (8x)
- Part G: Hinges (1x)
- Part H: Hinges (1x)
- Part I: Screws (8x)
- Part J: Screws (2x)
- Part K: Allen key (1x)
- Part L: Screws (2x)
- Part M: Screws (2x)
- Part N: Dowels/Pegs (2x)
- Part O: Door panel connectors (2x)
Installation Steps
Step 1: Prepare the Unit
Apply any provided seals or trim pieces to the appliance. This typically involves peeling off adhesive backing and pressing firmly into place.
Step 2: Attach Mounting Bracket & Position Unit
Attach the mounting bracket (Part C) to the top rear of the dishwasher unit. Carefully lift the unit and slide it into the designated cabinet space. Ensure it is correctly aligned.
Step 3: Connect Utilities
Connect the water inlet hose, drain hose, and electrical power cord. Ensure all connections are secure and meet local plumbing and electrical codes. Refer to diagrams for specific connection points and required clearances.
Step 4: Install Cabinet Door Hinges
Attach the hinges (Parts G, H) to the appliance door and the cabinet frame using the specified screws (e.g., E, F, I, J). Follow the diagrams precisely for correct placement and orientation.
Step 5: Secure Unit to Cabinetry
Use the provided mounting brackets (Part D) and screws (Part E) to secure the dishwasher unit to the surrounding kitchen cabinets. This prevents the unit from tipping forward.
Step 6: Attach Decorative Door Panel
Mount the decorative front panel (e.g., FINPUTSAD or RENGÖRA style) onto the appliance door. This is typically done using connectors (Part O) and screws (Parts L, M).
Step 7: Adjust Door Alignment
Adjust the door hinges to ensure the decorative panel is perfectly aligned with the surrounding cabinetry. The hinges allow for adjustments in multiple directions, including up/down and in/out (up to 4mm adjustment indicated).
Step 8: Final Checks and Leveling
Adjust the leveling feet at the base of the unit to ensure it is stable and perfectly level. Check all connections again for leaks or loose fittings. Ensure the unit is securely fastened to the cabinets.
Step 9: Final Operation Check
Run a test cycle to confirm the dishwasher operates correctly and the door opens and closes smoothly.
Dimensions and Clearances
For 60cm Units:
- Overall Height: 820-900 mm
- Minimum Cabinet Width: 600 mm
- Minimum Recess Depth: 560 mm
- Appliance Width: 598 mm
- Appliance Depth: 555 mm
For 45cm Units:
- Overall Height: 820-900 mm
- Minimum Cabinet Width: 450 mm
- Minimum Recess Depth: 560 mm
- Appliance Width: 448 mm
- Appliance Depth: 555 mm
Water Pressure Requirements:
- Minimum: 0.05 MPa / 0.5 Bar
- Maximum: 1 MPa / 10 Bar
Connection and Installation Clearances:
- Water/Drain Hose Length: Approximately 1300mm to 1500mm
- Electrical Cable Length: Approximately 1500mm
- Minimum space for pipes/cables: ⌀ min: 25 mm
- Minimum space for pipes/cables: min: 10 mm
- Minimum space for pipes/cables: min: 400 mm, max: 800 mm
General Warnings & Notes
- ⚠️ Do not use abrasive cleaners or sharp objects that could damage the appliance surfaces.
- ⚠️ Ensure the appliance is properly grounded for electrical safety.
- ⚠️ Avoid installing the unit near direct heat sources.
- ℹ️ This appliance is designed for seamless integration into standard kitchen cabinetry.
- ℹ️ Detailed diagrams are provided for specific assembly steps, including door panel and hinge installation.
- ❌ Do not attempt to repair or replace parts unless explicitly stated in the manual.
