WALI Single Monitor Desk Stand
Model: MF001/MF001-W
Specifications: 75x75/100x100 VESA compatibility, Maximum 32" screen size, 10kg (22lbs) weight capacity.
Important Safety Information
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. WALI cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIP-OVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIP-OVER.
TO HELP PREVENT TIP-OVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIP-OVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIP-OVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Parts Included
- VESA Plate (A) x 1
- Monitor Arm (B) x 1
- Weighted Base (C) x 1
- Pole (D) x 1
- Allen Key 3mm (G) x 1
- Allen Key 5mm (H) x 1
- Allen Key 6mm (I) x 1
- Wire Clip (J) x 1
- M4x12 Bolt (M-A) x 4
- M4x16 Bolt (M-B) x 4
- M5x12 Bolt (M-C) x 4
- M5x16 Bolt (M-D) x 4
- D5 Washer (M-E) x 4
- Spacer (M-F) x 4
Assembly Instructions
Step 1: Attach Pole to Base
Install the Pole (D) to the Weighted Base (C) using Bolts (M-A) and tighten with the 3mm Allen Key (G).
Step 2: Attach Monitor Arm to Pole
Slide the Wire Clip (J) and Monitor Arm (B) onto the Pole (D). Adjust to the preferred height and tighten using the 6mm Allen Key (I).
Step 3: Attach VESA Plate to Monitor
Step 3.3a: For Flat Back Monitors
Select M4x12 Bolt (M-A) or M5x12 Bolt (M-C) based on your monitor. Attach the VESA Plate (A) along with D5 Washers (M-E) to the mounting holes on the back of the monitor. Tighten with a screwdriver (not included).
Note: Hand-thread screws into the threaded inserts on the back of your monitor to determine which screw diameter (M4 or M5) to use.
Compatibility Check:
- Flat Monitor: Use screws without spacers.
- Inset Holes or Round Monitor: Use screws with spacers (M-F).
Step 3.3b: For Curved Back Monitors
Select M4x16 Bolt (M-B) or M5x16 Bolt (M-D) based on your monitor. Attach the VESA Plate (A) along with D5 Washers (M-E) and Spacers (M-F) to the mounting holes on the back of the monitor. Tighten with a screwdriver (not included).
Step 4: Mount Monitor to Arm
Place the assembled monitor onto the Monitor Arm (B). Ensure stability and tighten the VESA Plate (A) using the provided nut (F).
Step 5: Adjust Tilt Joint
Tighten or loosen the tilt joint using the 5mm Allen Key (H).
Step 6: Route Cables
Guide the monitor cables through the Wire Clip (J).
Step 7: Store Allen Keys
Store the Allen Keys (G, H, I) in the Wire Clip (J).
Step 8: Adjust Monitor Position
Manually swivel, tilt, or rotate the monitor to achieve the best viewing angle. The stand allows for 180° rotation, 360° swivel, and +/- 45° tilt.
Conclusion
Thank you for choosing WALI. WALI supports the technology that brings your home to life, offering high-quality products, professional customer service, and extensive technical support.
