EPLO Remote Control Instructions

Remote Control Installation

Holder Installation Method 1:

1. Drill a 6 mm diameter hole in the wall to a depth of about 35 mm.
2. Remove the double-sided adhesive tape on the back of the holder.
3. Install a wall anchor into the hole, stick the holder to the wall, and secure with screws. Then, stick the patch with tape.

Holder Installation Method 2:

1. Clean and dry the pre-installation area of the holder.
2. Remove the double-sided adhesive tape on the back of the holder.
3. Stick the holder to the wall vertically and then stick the patch with tape.

Battery Installation

1. Insert batteries into the remote control.
2. Put the remote control into the holder.

Notice

• Please ensure the remote control is within reach when a person is on the seat.
• Do not install or use the product in damp places such as a shower room.
• Do not place the product in a place where it is easily exposed to water.

Rear/Front Washing

Press the "REAR MOVE" button for rear washing. Press again to shift to oscillating washing (nozzle moves forward and backward). Washing stops automatically after one cycle or immediately if the "STOP" button is pressed.

Press the "FRONT MOVE" button for front washing. Press again to shift to oscillating washing. Washing stops automatically after one cycle or immediately if the "STOP" button is pressed.

Drying/Dryer Temperature

Press the "DRY DRYER TEMP" button to start drying. The indicator shows the current air temperature level. Drying stops automatically after one cycle or upon leaving.

During drying, press the "DRY DRYER TEMP" button again to adjust air temperature between levels 0-5. Level 0 is room temperature (indicator light off).

Water Volume Adjustment

While using rear or front washing, press the "+" or "-" buttons to adjust water volume. The indicator light shows the current water volume level.

Nozzle Position Adjustment

While using rear or front washing, press the "Λ" or "V" buttons to adjust the nozzle position. There are 5 adjustable levels.

Energy Saving

Long press the "HOLD TO ECO" button to enter energy saving mode. Long press again to exit.

In energy saving mode, the seat temperature is set to Level 1. If the seat temperature was neutral before entering this mode, it remains neutral.

Remark: Energy saving mode is suspended when the seat is used. The seat heats up immediately, and energy saving mode is restored once the seat is no longer in use.

Water Temperature Adjustment

Short press the "WATER TEMP" button to adjust water temperature between levels 0-5. The indicator light shows the current level. Level 0 is room temperature (indicator light off).

Seat Temperature Adjustment

Short press the "SEAT TEMP" button to adjust seat temperature between levels 0-5. The indicator light shows the current level. Level 0 is room temperature (indicator light off).

Night Light

Short press the "LIGHT" button to turn the night light on/off.

For intelligent mode, long press the "LIGHT" button. The night light will adjust based on ambient light. To exit intelligent mode, short press the "LIGHT" button.

Half Flush/Full Flush

Short press the "HALF FLUSH" button for a half flush.

Short press the "FULL FLUSH" button for a full flush.

Long press the "FULL FLUSH" button to turn the auto flush function on/off. When auto flush is on, the toilet flushes automatically after the user leaves the seat.

Foam Setting

1. Short press the "FOAM SHIELD" button to activate the foam shield function.
2. Long press the "FOAM SHIELD" button to start pumping until foam appears, then release. (Note: This is for initial installation or when foam agent is refilled. Using it otherwise may waste foam agent.)
3. Press "FOAM SHIELD" then "MUTE" to turn on automatic foaming (one beep).
4. Press "FOAM SHIELD" then "MUTE" again to turn off automatic foaming (two beeps).

When automatic foaming is on, the foam shield function activates automatically when the user is seated. (Automatic foaming is off by default).

Auto Deodorization

Short press the "DEODORIZER" button to turn auto deodorization on/off. The function activates when the user is seated and stops after leaving. It also stops during drying. (Function is on by default).

Quiet Mode

Short press the "MUTE" button to turn quiet mode on/off.

User Code

IR Remote Control Pairing:

1. Power on the toilet. Self-inspection starts and ends with one beep.
2. Press and hold the "STOP" button, then press the "HOLD TO ECO" button. The indicator light will flash.
3. Press the "+" or "-" buttons to select user 1-9. The indicator light shows the selected user code and flashes.
4. Press the "STOP" button, then press the "HOLD TO ECO" button. The main unit beeps once, indicating successful pairing.

User selection is indicated by lights.

Other Operations