EPLO iX7-PRO Smart Toilet Installation Guide

Installation

Tools required for installation. Please have these tools prepared prior to installation.

Required Tools

• Drill (Dia. 0.24in)
• Silicone gun
• Teflon tape
• Knife
• Marking pen
• Spanner (model varies for different pipes)
• Screwdriver
• Measuring tape
• Measuring cup

Item list (Confirm that all below items are inside the box)

• Intelligent toilet (1 set)
• T-valve (1 pcs)
• Two AAA Battery
• Remote control set (1 set)
• Mounting accessory kit (2 pcs) (holder 1 pc, screw 2 pcs)
• Wax Ring (1 pcs)
• Installation Book & User Manual
• Sealing Flange
• Mounting Template
• Battery box assembly (1 set)

Please confirm all the aforementioned items are inside the package. If there are any omissions, please contact EPLO customer service.

The flange and wax ring provided are for backup only. EPLO recommends purchasing thicker wax rings if your flange is lower than the ground to achieve strict sealing.

Before you Install

Checking your water supply

Please check and make sure that water is coming out of the toilet water supply valve properly!

Confirm dimensions of product with installation space

Diagram Description: A diagram showing the side view, front view, and top view of the toilet with key dimensions labeled. The rough-in dimension is indicated as 12 inches. The distance from the wall to the center of the sewage outlet is shown to be at least 12 inches.

• Please ensure that the distance between the center point of the sewage outlet and the wall is not less than 12 inches!
• The power consumption of the toilet is not high, its maximum working current does not exceed 10A. A specific power line is not required; a regular socket in your home is sufficient.
• For installation questions, take photos of your installation environment and send an email to: support@eplo.com. EPLO has experienced Technical Support to provide the fastest solutions.

Installing your product

Install your unit using the following steps:

1. Open the box right side up

   Remove the accessories first, then remove the unit from the top, as shown in the diagrams below.

   Diagram Description: Illustrations showing the process of unboxing the smart toilet, starting with accessories and then lifting the main unit out of the box.

2. Mark your drainage hole with a cross

   Cardboard installation:

   • Align cardboard with the centerline of drain outlet.
   • Draw contour line according to cardboard.

   Diagram Description: A diagram illustrating how to use the cardboard packaging as a template to mark the drain outlet on the floor.

3. Mounting bracket installation

   Assemble the mounting bracket with bolts and then install them to the pre-installed flange plate on the ground and lock tight with nuts.

   Diagram Description: An exploded view of the mounting bracket assembly, showing the bracket, bolts, washers, and nuts.

4. Install the ceramic body, water supply hose, T-valve

   1. Place the wax ring on the drain hole at the bottom of the ceramic.
   2. Install sealing flange into drain outlet.
   3. Install ceramic toilet on corresponding position according to contour line.
   4. Put the screw through the fixing sleeve and then install it through the holes (on both sides of the toilet ceramic) to the mounting bracket on the ground, and lock tight with a tool.
   5. Put the decorative cap on the fixing sleeve.
   6. Attach the flush water hose to the T-valve and tighten.
   7. Attach the clean water hose to the T-valve and tighten.
   8. Connect the T-valve to the water supply and tighten. Use gasket to prevent water leakage.
   9. Finish installation.

   Diagram Description: A series of diagrams illustrating the step-by-step installation of the ceramic toilet body, including placing the wax ring, sealing flange, connecting hoses, and securing the unit.

   Tips: The toilet is heavy; open the seat cover to carry it by two people.

5. Installing the remote

   1. Drill two 6mm (0.24 inch) diameter holes on the wall (about 1.77 in deep).
   2. Knock the anchors into the hole with a hammer.
   3. Secure the holder with anchors.
   4. Use the screws to secure the holder to the wall.
   5. Remove the battery cover from the backside of the remote to install batteries.
   6. Once finished, the remote is ready to be placed in its holder.

   Diagram Description: Step-by-step illustrations showing how to install the remote control holder on the wall, including drilling, inserting anchors, and screwing the holder in place. It also shows how to insert batteries into the remote.

   Note: Use proper mounting tools for special wall surfaces (such as wood, HDF, etc.). The remote control holder should be installed away from the bidet's spray trajectory and within reach when seated on the unit. Ensure nothing blocks the transmission between the toilet and its remote.

6. Installing and replacing the battery box

   Installing the external battery box

   1. Remove the connecting cables from the position indicated.
   2. Connect the waterproof DC power plug and tighten the waterproof cap.
   3. Place the battery box in a suitable position as shown.
   4. For any questions, call the customer service center or your local dealer.

   Note: The battery should be placed out of the reach of children. Some batteries and connecting wires may have slots; do not forcibly insert to avoid product damage.

   Replacing the external battery box

   1. Unscrew the waterproof cap at the connection of the waterproof DC power plug.
   2. Pull out the waterproof DC power plug.
   3. Replace the battery box assembly with a new one.
   4. For any questions, call the customer service center or your local dealer.

   Note: The waterproof grade of the battery box for power failure and flushing is IPX6. A single battery box can support approximately 200 flushes during power failure.

   Diagram Description: Illustrations showing the installation and replacement of the external battery box, including connecting the waterproof DC power plug and tightening the cap.

7. Testing water flow

   1. Open the water supply angle valve to maximum.
   2. Confirm various connecting parts are not water leaking. In case of water leaking, unfasten the nuts again and install them again.

   Diagram Description: A diagram showing the water supply angle valve being opened to its maximum setting.

8. Connecting power

   1. Connect to the grounding.
   2. Plug in AC 120V power plug.
   3. Check to see if the power light is on.
   4. Press the side button to confirm that the toilet is powered on.
   5. Check to see if the power is on.

   Diagram Description: Illustrations showing the power connection process, including grounding, plugging in the AC power, and checking indicator lights.

Testing the product

Test whether the functions of the buttons on the remote control and the button on the side of the body are normal.

Are all the functions working properly?

• Rear Wash, Front Wash (Including water pressure & nozzle position adjustment)
• Heated Dryer
• Water & Seat temperature Adjustment
• Nozzle cleaning
• Remote control

All functions listed above should be tested.

Checking Rear Wash

Please use your hand to hold the seat sensor area, press the side "▶" button or press the "Rear" button on the remote control, and use your hand to cover the front of the washer to block the flow of wash water to avoid spraying water on your body or clothing.

Matching your remote control code

Note: When the product leaves the factory, the remote control and the product are connected. If the remote control fails, please re-connect the code as following methods:

1. Unplug the product's plug, press the stop key for a few seconds until the level light is flickered.
2. Plug the attaching plug when the remote control is closer to the product.
3. The level light stops flickering and then is lighted on.
4. At this time, the remote control and product are re-connected.

Diagram Description: A step-by-step visual guide on how to re-pair the remote control with the smart toilet, showing button presses and indicator light changes.