Installation Guide for EPLO models including: EP-E18MAX, EP-E18MAX Enjoy Smart Life Toilet Bidet, Enjoy Smart Life Toilet Bidet, Smart Life Toilet Bidet, Toilet Bidet
How to Choose the Right Smart Toilet for Your Bathroom – EPLO
Tus opciones de privacidad – EPLO
ENJOY SMART LIFE STRONG DRYER TEMP. Installation Manual Model: EP-E18MAX/EP-F19MAX Thank you for choosing our products. Please read the instructions carefully before installation and keep it available for future maintenance or reference. E-mail:service@eplo.com Content Installation preparation 01. Remote control installation 01 02. Battery installation 01 Usage instruction 01. Remote control illustration 02 02. Rear/Front washing 03 03. Drying/Dryer temperature 04 04. Water volume adjustment 04 05. Nozzle position adjustment 04 06. Energy saving 04 07. Water temperature adjustment 05 08. Seat temperature adjustment 05 09. Night light 05 10. Full flush/Half flush 05 11. Auto lid open/close 06 12. Wind speed adjustment 06 13. User code 06 14. Other operations 06 Installation Preparation Remote control installation Remote control holder installation 1 1. Drill a 6 mm diameter hole in the wall to a depth of about 35 mm. 2. Remove the double-sided adhesive tape on the back of the holder. 3. Install an anchor into the hole, stick the holder to the wall and secure with screws and then stick the patch with tape. Double-side tape patch Remote control holder installation 2 1. Clean and dry the pre-installation area of the holder. 2. Remove the double-sided adhesive tape on the back of the holder. 3. Stick the holder to the wall vertically and then stick the patch with tape. Installation area Double-side tape Battery installation: 1. Insert batteries into the remote control. 2. Put the remote control to the holder. patch Battery cover Notice: 1. Please ensure the remote control is within reach when a person on the seat. 2. Do not install and use the product in damp places such as a shower room. 3. Do not place the product in a place where it is easily exposed to water. 01 Installation Preparation Remote control illustration Strong/ Dryer temperature Rear washing/ oscillating washing Front washing/ oscillating washing Nozzle moving forward Water reducing Nozzle moving backward Water temperature Wind speed Full flush Open/ Close the lid STRONG DRYER TEMP. Indicator light Water increasing Stop/Energy saving Night light Seat temperature Half flush Open/Close the seat 02 Usage Instruction Notice : · Only when the user is seated and the buzzer beeps can the functions of front/rear washing and drying be activated. · Please sit backward on the seat for correct washing position and to avoid splashing. · The nozzle will continue to spray for 1-2 seconds after user stands up during washing, so please press "STOP" button before standing up. REAR|MOVE · Press " " button, the indicator light is on showing current water temperature level, it starts rear washing; Press again " " button to shift to oscillating washing (nozzle moves forward and backward to expand washing area). The washing will stop automatically after one cycle, while it will stop immediately if the user presses " " button. FRONT|MOVE · Press " " button, the indicator light is on showing current water temperature level, it starts front washing; Press again " " button to shift to oscillating washing (nozzle moves forward and backward to expand washing area). The washing will stop automatically after one cycle, while it will stop immediately if the user presses " " button. Pulse cleaning function (Only for the product with pulse cleaning function.) · During front/rear washing, long press " " or " " button to turn on/off pulse cleaning mode. STRONG DRYER TEMP. Rear washing Front washing 03 Usage Instruction STRONG|DRYER TEMP (Only for the product with drying function) STRONG DRYER TEMP. Press " " button, the indicator is on showing current air temperature gear, it starts drying. The drying will stop automatically after one cycle or after user leaves the seat. Under drying, press " " button to adjust the air temperature, and the indicator light is on showing the air temperature gear. Drying When the indicator light is off, the temperature is at gear 0 (room temperature), The air temperature adjustment mode is cycle through 0-5 gears. Under drying, press the air outlet position " "," "button, the indicator light is on showing the current air outlet gear, and the air outlet position can be adjusted between 0-5 gears. Room Level 1 temperature Level 2 Level 3 Level 4 Level 5 Water volume adjustment · Press "+" or " - " button when it is under function of rear washing or front washing, the indicator light is on showing current water volume level, and water volume can be adjusted. Nozzle position adjustment · Press "" or "" button when it is under function of rear washing or front washing, the indicator light is on showing current nozzle position, and nozzle position can be adjusted in 5 levels. Water volume Nozzle Energy saving Long press " " button to enter energy saving mode, long press " " button again to exit energy saving mode. Under energy saving mode, seat temperature is set to Level 1 for energy saving. (Note: If the seat temperature before energy saving is neutral, then it will be neutral as well.) Remark: Energy saving mode will be suspended and the product will enter functional mode if the seat is used. The seat starts to heat immediately (without turning off the seat temperature), and the energy saving mode is restored once the seat is no longer being 04 used. Usage Instruction Water temperature adjustment Short press " " button to adjust the water temperature between 0-5 level. The indicator light is on showing current water temperature level. When the indicator is off, the temperature is at level 0 (room temperature). Room Level 1 temperature Level 2 Level 3 Level 4 Level 5 Seat temperature adjustment Short press " " button to adjust the seat temperature between 0-5 level. The indicator light is on showing current seat temperature level. When the indicator is off, the temperature is at level 0 (room temperature). Room Level 1 temperature Level 2 Level 3 Level 4 Level 5 Night light · Night light adjustmentShort press " " button to turn on/turn off night light. · Intelligent mode: Long press " " button to enter into intelligent mode (Night light LIGHT will be on or off depending on the surrounding light.). If the product is on intelligent mode, short press " " button to exit intelligent mode. (Factory setting: intelligent mode) Half flush/Full flush · Short press " · Short press " · Long press " " button, the toilet starts half flushing. " button, the toilet starts full flushing. " button to turn on/off auto flush function. When the auto flush function is turned on, toilet will automatically flush after detecting user leaving the seat. FULL FLUSH HALF FLUSH 05 Usage Instruction Auto lid open/close Short press " " buttonopen or close the lid. Short press " " buttonopen or close the seat. Long press " " button to turn on/off auto lid open/close function. (Only for the toilet with auto lid open/close function.) Wind speed adjustment Under drying, press " " button to switch the wind speed gear, and the gear adjustment will be cycled from 1-3 gears. Long press the " " button to turn on/off the drying moving function. User code · Radio frequency remote control Shut off the power supply of toilet Press and hold " " button, then press " " button, the indicator light will flash. Re-connect the power plug and press "reset" button. The indicator stops flashing and stays on for 2 seconds, indicating that the remote control and the toilet are matched successfully. It beeps once when the self-inspection completes. Then the remote control is ready for use. Other operations Quiet mode · Press and hold the " " button and press the " " button to turn on/off quiet mode. Auto deodorization · Press and hold " " button and press " " button to turn on/off auto deodorization function. The deodorization function will be automatically turned on when the user is seated, and will stop after user leaves. Under drying, deodorization will stop. ((This button combination is only applicable to toilets with auto deodorization function, and the auto deodorization function is turned on by default when the power is on every time.) 06 Usage Instruction Sanitation function · When no one seated and washing/drying is off, long press " " button to turn on plasma sanitation function.This function will stop automatically after 2 hours. Under this mode, if any other button is pressed or user is seated, it will stop automatically. (Only for the toilet with sterilization function.) Automatic pre-wetting function · Press and hold " " button and press " " button to turn on or off automatic pre-wetting function. After the automatic pre-wetting function is turned on, the pre-wetting function will be performed when the user is detected to be seated. (Only for the toilet with automatic pre-wetting function.) Foot sensor function · Long press " " button to turn on/off foot sensor function. Foot sensor is deactivated when the user is seated. (Only for the toilet with foot sensor function.) Remark: · The buzzer will "BEEP" once when the user presses one button indicating that the main unit receives the signal and conduct the operation accordingly. If the buzzer doesn't sound, it means the main unit doesn't receive the signal, please adjust the remote control direction and repress the button. · In case of power cut during nozzle spraying, the wand cannot be retracted, please wait until the power is restored. In case of a power cut for a long period, please push the wand softly back by hand. Do not push hard, to avoid damage to wand and electrical machine. 07 WWW.EPLO.COM WhatsApp The picture of product may not entirely consistent with actual appearance and color because of product improvements, please in kind prevail. ASVFAF0401028A-1.0Adobe PDF library 10.01 Adobe Illustrator CS6 (Windows)