BAGGEBO Assembly Instructions
Safety Warning
WARNING! Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.
Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instruction carefully.
Parts and Tools
The following parts and hardware are included for assembly. Ensure all parts are present before beginning.
Hardware
- Screw (100229): 8x
- Dowel (101345): 16x
- Screw (119976): 1x
- Screw (109558): 2x
- Screw (109041): 1x
- Screw (101068): 1x
- Washer (100823): 2x
- Washer (101313): 1x
- Bracket/Clip (103651): 1x
- Bracket/Clip (122628): 4x
- Cap/Plug (10062514): 1x
- Cam lock/Connector (133127): 1x
- Cam lock/Connector (139477): 1x
- Bracket (10119658): 2x
- Dowel/Plug (10119600): 2x
- Bracket/Support (105493): 1x
- Bracket/Support (100006): 1x
- Nails (319503): 1x (bag)
- Bracket (106989): 1x
- Nail/Pin (101221): 14x
- Bracket/Clip (105494): 1x
Tools Required
You will need a screwdriver and a hammer.
Assembly Steps
Step 1
Attach the bracket (103651) to the base panel using two screws (109558). Ensure the bracket is oriented correctly as shown in the diagram.
Step 2
Insert four dowels (101345) into the pre-drilled holes on the side panels.
Step 3
Connect the side panels to the base panel by aligning the dowels with the corresponding holes.
Step 4
Insert four dowels (101345) into the pre-drilled holes on the top panel.
Step 5
Attach the top panel to the assembled sides using the tool (100006) and four screws (100229).
Step 6
Insert two dowels (101345) into the pre-drilled holes on the internal divider panels.
Step 7
Insert six dowels (101345) into the pre-drilled holes on the side panels where the internal dividers will be placed.
Step 8
Attach the internal divider panels to the cabinet structure using four screws (100229).
Step 9
Carefully attach the back panel to the rear of the cabinet using fourteen nails (101221) and the clip (105494). Ensure the panel is square before nailing.
Step 10
Attach four brackets/clips (122628) to the cabinet body using a hammer, as shown in the diagram.
Step 11
Attach the wall mounting bracket (109041) to the top of the cabinet using one screw (100823) and one washer (109041). Ensure it is securely fastened.
Step 12
Position the furniture against the wall. Adjust the wall bracket (100823) to align with wall mounting points. Secure the bracket to the wall using appropriate wall fixings (not included).
Step 13
Insert two plugs (10119600) into the designated holes on the cabinet.
Step 14
Attach the door hinges/brackets (10119658) to the cabinet body using two plugs (10119600).
Step 15
Attach the door to the cabinet by aligning the hinges with the pre-drilled holes. Secure using one screw (101068) and one washer (101313).
Step 16
Insert the door pins (139477 and 133127) into the corresponding holes on the door.
Step 17
Align the door pins with the receiving holes on the cabinet and attach the door.
Step 18
Push the door firmly until it clicks into place, securing it.
Step 19
Attach the door handle/knob (10062514) to the door using one screw (119976).
Important Safety Information
This furniture must be securely fastened to the wall using the provided wall attachment devices to prevent tip-over accidents. Always use screws and plugs suitable for your wall type. If you are unsure, consult a professional.
