Toucan Wireless Security Camera PRO

Regulations & Compliance

FCC Statement

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

ISED Regulatory Compliance

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1. L'appareil ne doit pas produire de brouillage; 2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

RF Exposure Compliance

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Cet équipement est conforme aux limites d'exposition aux radiations FCC/IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.

Items included

• Microphone
• Camera Lens
• Radar Sensor
• LED Indicator
• Speaker
• Wireless Security Camera PRO
• Adhesive Tape
• Mounting Screws
• Wall Anchors
• Charging Cable
• Magnetic Ball
• Magnetic Base Mount
• User Manual
• Warranty Card
• Thank You Card

Charge your Wireless Security Camera PRO

Open the mirco USB plug cover, plug in the micro USB cable to charge the camera.

Recommend to fully charge the device before 1st use.

The camera features a SET button and a RST button. It also has a threaded screw hole for accessory mounting.

Setup your Wireless Security Camera PRO

1. Download the Toucan App

   Scan QR code or visit www.toucansolution.com/pages/toucan-smart-home-app. Available at Apple App Store® and Google Play™.

2. Login to the App

   Open the app and create a free account. Enter your Email ID and Password to log in.

3. Add your device

   Tap the "+" icon to add a device.

4. Connect your device

   Press and hold the SET button until the LED light on the front blinks blue to enter the setup mode. Follow the instructions in the Toucan App to complete the setup.

   LED Status Indicators:

   • Flashing BLUE: Setup Mode
   • Flashing PURPLE: Connecting to cloud server
   • Flashing RED: Connection Failed

Install your Wireless Security Camera PRO

1. Check WiFi signal at installation area

   Take the camera to the planned installation area. Tap on the camera in the Toucan App Dashboard to bring up Live View to make sure there is good WiFi signal at the installation area.

2. Attach the magnetic ball

   Screw the magnetic ball onto the back of the camera.

3. Mark the Magnetic Mount's preferred placement

   Using the magnetic mount as a template, mark where you want to mount the camera with a pencil.

4. Choose how you want to secure the Magnetic Mount

   Option A: Uses screws for mounting.

   Option B: Uses 3M Adhesive for mounting. Allow 24 to 48 hours curing time before placing the camera onto the Magnetic Mount to ensure maximum bonding strength. Apply the adhesive on dry surfaces only. It is suitable for UPVC, wooden or smooth surface door frames. Not suitable for brick or stone.

   Option C: Uses both screws and adhesive.

5. Place the camera on the Magnetic Mount

   Place the camera with the ball onto the Magnetic Mount. It will attach firmly. Adjust camera angle for best suited view.

For detailed setup procedure, please refer to the Toucan website (www.toucansolution.com) or scan the QR code.