XBA-PHP6 Option Switch Settings
Supported bills: PHP 20, 50, 100, 200, 500, 1000 (6 denominations).
XBA-PHP6 (Pulse/MDB/ICT002U/ICT104U/ICT104V) Function Settings
| FUNCTION | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Reject PHP 20 | ON | |||||||
| Accept PHP 20 | OFF | |||||||
| Reject PHP 50 | ON | |||||||
| Accept PHP 50 | OFF | |||||||
| Reject PHP 100 | ON | |||||||
| Accept PHP 100 | OFF | |||||||
| Reject PHP 200 | ON | |||||||
| Accept PHP 200 | OFF | |||||||
| Reject PHP 500 & 1000 | ON | |||||||
| Accept PHP 500 & 1000 | OFF | |||||||
| Disable Bill Reject 4 Times BA Stop By 30 Sec | ON | |||||||
| Enable Bill Reject 4 Times BA Stop By 30 Sec | OFF | |||||||
| Stack Banknote when Power-up | ON | |||||||
| Reject Banknote when Power-up | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF |
| FUNCTION | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Inhibit Active HIGH | ON | |||||||
| Inhibit Active LOW | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Pulse Mode | MDB Mode | ICT104V Mode | ||||||
| Credit-Pulse Normal LOW (SF=100, DPP=2) | Connect with coin changer | |||||||
| Credit-Pulse Normal HIGH (SF=1, DPP=0) | Connect with ICT JPSTD converter board | |||||||
| Pulse Mode (Other Mode) |
||||||||
| 1 pulse / PHP 10 | MDB Mode OFF OFF |
ICT002U Mode OFF ON |
ICT104U Mode ON OFF |
ICT104V Mode ON ON |
||||
| 5 pulses / PHP 10 | MDB Mode OFF OFF |
ICT002U Mode OFF ON |
ICT104U Mode ON OFF |
ICT104V Mode ON ON |
||||
| 10 pulses / PHP 10 | MDB Mode OFF OFF |
ICT002U Mode OFF ON |
ICT104U Mode ON OFF |
ICT104V Mode ON ON |
||||
| 20 pulses / PHP 10 | MDB Mode OFF OFF |
ICT002U Mode OFF ON |
ICT104U Mode ON OFF |
ICT104V Mode ON ON |
||||
[Note] Manufacture setting
Note: 1. After setting dip switch of the credit pulses, you should reset the bill acceptor again.
2. Calibration card is needed.
DIP Switch Location
This dip switch is located at the side of XBA.
Diagram description: A side view of the bill acceptor unit showing the location of the DIP switch, labeled (2). An LED indicator is also visible.
Diagram description: A view of the bill acceptor's internal components. It shows the CPU board, with a DIP switch labeled (1) on it. Arrows indicate that the CPU board cover needs to be removed first to access the DIP switch.
Currency Assign Data
| Interface | Bill value | Pulse | MDB | ICT104U | ICT104V | ICT002U |
|---|---|---|---|---|---|---|
| BV1 | P 20 | P 20 | P 20 | P 20 | P 20 | P 20 |
| BV2 | P 50 | P 50 | P 50 | P 50 | P 50 | P 50 |
| BV3 | P 100 | P 100 | P 100 | P 100 | P 100 | P 100 |
| BV4 | P 200 | P 200 | P 500 | P 500 | P 500 | P 500 |
| BV5 | P 500 | P 500 | P 1000 | P 1000 | P 1000 | P 1000 |
| BV6 | P 1000 | P 1000 | P 200 | P 200 | P 200 | P 200 |
Appendix
© 2016 International Currency Technologies Corporation
Vol. 3.0 Part Number: SWT8PH63000-R
