CYCPLUS GPS Bike Computer M3

GPS Location - Quick Start Guide

To receive satellite signals, please remain static and make sure your device is used in an open and unobstructed area.

For a faster GPS fix, connect this device to the CYCPLUS Fit app and download the ephemeris data before riding.

1. Long press [L button ▶] to power on.
2. Acquiring a GPS signal after startup may take a few minutes. ☀ appears to indicate the device is ready.
3. Press [L button ▶] again to start recording. ▶ appears when recording starts.
4. Long press [R2 button ■] to save the recorded data. The 'SAVE' message will blink for 4 seconds. Once the ▶ or ☀ icon disappears, the recording is successfully saved.
5. Long press [L button ▶] to power off.

Specifications

Name: GPS Bike Computer

Model: M3

Product Size: 88 × 52 × 20 mm

Screen Size: 2.8 inch LCD

Product Weight: 80 g

Memory Capacity: 150 hours

Battery: 1500 mAh 3.7 V

Battery Life: 100 hours

Charging Time: ≈ 2.5 hours

Charging Port: USB Type-C

APP Connection: BLE 5.0

Peripheral Connection: ANT+

Supported Peripherals: Speed sensor, Cadence sensor, Heart rate monitor, Power meter.

Waterproof: IPX6 (Water-resistant, not submersible)

About Buttons

The button functions in normal use are as follows. Please refer to the setting instructions for button operations in the settings.

Data Display

This device has 4 data pages, which can be easily accessed by short pressing the R1 button. The data displayed with the factory settings is as follows:

The upper section of the screen displays fixed data fields that cannot be customized. The display content on each page is as follows:

• Clock: Displays the current time, with the option to set the time zone in the settings.
• Recording Status: No symbol – No trip recording in progress. ▶ – Trip recording is active. █ – Trip recording is paused. Flashing █ – Auto-pause is activated when stopped; recording resumes automatically upon movement.
• GPS: ☀ – No GPS signal. ☀ – GPS is working properly.
• Phone Connection: 📱 Indicates that the device is already connected to the phone.
• Temperature: Display the current temperature, choose °C or °F in the settings.
• Speed Sensor: 🚢 Indicates that the device is connected to a speed sensor, and the speed data comes from the speed sensor.
• Modes: No symbol – Speed and gradient data are shown as real-time values. ⌀ – Speed and gradient data are shown as average values. MAX – Speed and gradient data are shown as maximum values.
• Speed Unit: Choose between metric (KMH) or imperial (MPH) units in the settings. This will also affect distance and elevation gain/loss display.

Each page displays 4 customizable data fields in the lower half of the screen. You can customize these fields using the CYCPLUS Fit app.

Customizable Data Fields:

• TIME Riding Time
• DST Riding Distance - In metric mode, values below 1 kilometer are displayed in meters. In imperial mode, values below 0.1 miles are displayed in feet.
• ODO Odograph - In metric mode, values below 1 kilometer are displayed in meters. In imperial mode, values below 0.1 miles are displayed in feet.
• SPD Speed, shown in the same unit as your setting
• HR Heart rate (requires heart rate monitor)
• PWR Power (requires power meter)
• CAD Cadence (requires cadence sensor)
• ALT Elevation, always shown in meters
• AST Elevation Gain - In metric mode, the display shows in meters, switching to kilometers after 9999 meters. In imperial mode, the display shows in feet, switching to miles after 9999 feet.
• DES Elevation Loss - In metric mode, the display shows in meters, switching to kilometers after 9999 meters. In imperial mode, the display shows in feet, switching to miles after 9999 feet.
• AVG Indicates average data.
• MAX Indicates maximum data.

Settings

Connecting and Configuring:

You can quickly set up the CYCPLUS Fit app to connect and configure the device. Or use buttons to set the device as follows:

Long press [R1 button ≤] to enter settings. Short press [R1 button ≤] to cycle through 8 setting pages.

• C2: ANT+ Sensors
• C3: Wheel Circumference
• C4: Time Zone
• C5: Speed Unit
• C6: Temperature Unit
• C7: Factory Reset
• C8: Odograph
• C9: Unpair Sensors

Complete setting configuration: Long press [R1 button ≤] to return to the home page after finishing.

ANT+ Sensors Connection

Press the L button ▶ to start searching for ANT+ sensors.

When the search starts, the device will check for four types of sensors: speed, heart rate, power and cadence. If a sensor is detected, its data will be displayed. If no sensor is found, a horizontal line will appear in its place.

The device will return to the home page after 10 seconds.

Unpair the Paired Sensors

Go to the C9 page in the settings menu. Press the L button ▶ to unpair all connected sensors.

Wheel Circumference Setting

Press the L button ▶ to start the setting process.

Press the R1 button ≤ to adjust the value. The adjustable digit flashes.

Press the R2 button ■ to switch between digits.

Press the L button ▶ to confirm and save the setting. All digits flashing.

Time Zone Setting

Press the L button ▶ to start the setting process.

Press the R1 button ≤ to adjust the time zone.

Press the R2 button ■ to switch to the minute digits, then press the R1 button ≤ to adjust them. The adjustable digit flashes.

Press the L button ▶ to confirm and save the setting. All digits flashing.

Speed Unit Setting

Press the L button ▶ to start the setting process.

Press the R1 button ≤ to switch between KMH and MPH. The unit flashing.

Press the L button ▶ to confirm and save the setting.

Temperature Unit Setting

Press the L button ▶ to start the setting process.

Press the R1 button ≤ to switch between °C and °F. The temperature unit flashing.

Press the L button ▶ to confirm and save the setting.

Factory Reset

Press the L button ▶ to start the setting process. All digits flashing.

Press and hold the R2 button ■ to restore factory settings, then the device will power off. RECOVERY will be displayed.

Odograph Setting

Press the L button ▶ to start the setting process. All digits flashing.

Press the R1 button ≤ to adjust the value. The adjustable digit flashing.

Press the R2 button ■ to switch between digits. The adjustable digit flashing.

Press the L button ▶ to confirm and save the setting. All digits flashing.

APP Connection

Download and use the CYCPLUS Fit APP, which can help you to use this device more conveniently and provides additional services support.

You can download the app by scanning the QR code or searching for "CYCPLUS Fit" on Google Play or the App Store.

For iOS

For Android

Notes

1. Data recording: Long press the L button ▶ to power on the device, then press the L button ▶ to start recording the trip. Long press the R2 button ■ to save the record after finished the ride. The device will save the current record when it shuts down.
2. Memory: Once the memory is full, the device will overwrite previous records in chronological order.
3. Backlight: After setting the time zone, the screen backlight will automatically turn on from 18:00 to 09:00 each day. When the button is pressed, the backlight will turn on and turn off after 10 seconds.

Package List

• GPS Bike Computer
• Bike Computer Mount
• Rubber Pad
• Rubber Band x 3
• Charging Cable
• User Manual

About Installation

1. Use CYCPLUS Z1/Z3 bike mount (Sold separately)
2. Use the standard bike computer mount. Cross-fix the mount with rubber bands.

Manufacturer Information

Company: Chengdu Chendian Intelligent Technology Co., Ltd.

Address: No. 88 Tianchen Road, Chengdu, Sichuan Province, China.

Warranty: Free repair or replacement within 2 years for non-user-induced damage.

Contact: steven@cycplus.com

Tire Circumference Chart

Please use this chart for your reference. Tire size is shown on the side of the tire. Tire circumference may vary depending on tire size.

Made in China