Progress Lighting P500435 & P500436 Latham Collection Pendant Installation Guide

Package Contents

Hardware Contents (not actual size)

Missing Parts & Support

Missing parts? Please contact Customer Service at 1-800-447-0573, 8am-8pm (Eastern), Monday - Friday, or at customerservice@progresslighting.com

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or install the product.

⚠️ CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation.

⚠️ CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor.

❗ WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.

⚠️ CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.

Preparation

1. Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
2. Estimated assembly time: 30 minutes.
3. Tools required for assembly (not included): Phillips screwdriver ?, pliers ?, wire stripper ?, safety glasses ?, electrical tape ?, ladder ?.

Care and Maintenance

Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

Assembly Instructions

Step 1: Prepare Mounting Plate

Loosely thread the screws [AA] and the hex nuts [DD] onto the round mounting plate [CC] as shown. Adjust the screw length according to the fixture canopy depth.

Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.

Lift up the fixture and pass the screws [AA] through the two mounting holes in the fixture canopy. While holding the fixture, thread the screws [AA] in or out of the round mounting plate [CC] until 3/16" of threads are showing. This length should be sufficient for mounting.

Next, take the fixture down and tighten the hex nuts [DD] up against the round mounting plate [CC] to secure the screw length.

Diagram shows incorrect and correct mounting plate adjustment. The correct method displays screws [AA] and hex nuts [DD] on the mounting plate [CC], with 3/16" [5mm] of screw thread exposed for attachment to the outlet box. Text indicates: "Thread both screws up & down for adjustment".

Step 2: Attach Assembly to Outlet Box

Attach the prepared mounting plate assembly to the electrical outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.

Diagram illustrates the mounting plate [CC] being attached to an electrical outlet box with mounting screws. Arrows indicate tightening.

Step 3: Determine Hanging Length and Assemble Stems

Determine the desired hanging length of your fixture by adding/removing stems [FF]/[GG] and nipples [HH]. Cut the electrical wire and ground wire to the appropriate length, ensuring at least 6 inches of wire extends past the canopy for connections.

Do NOT cut electrical wires or ground wires until the overall length is determined.

Once hanging length is set, pull the wires through the unassembled stems [GG] and nipples [HH]. Then, assemble the stems and nipples tightly together.

Attach one end of the assembled stems to the fixture (A) and secure tightly. Pass wires through the canopy (B) and secure it tightly to the stems [FF].

Diagram shows stems [FF, GG] and nipple [HH] being assembled and threaded onto the fixture (A) and canopy (B). Wires are shown passing through the components.

Step 4: Make Electrical Connections

Strip 3/8" of insulation from the electrical wire ends.

Using wire nuts [BB]:

• Connect the smooth fixture wire to the white supply wire from the outlet box.
• Connect the ribbed fixture wire to the black supply wire from the outlet box.

Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.

Diagram illustrates wire connections using wire nuts [BB]. Shows smooth fixture wire to white supply wire, ribbed fixture wire to black supply wire, and ground wire to ground screw/wire nut.

Step 5: Secure Fixture to Canopy

Pass the screws [AA] through the two holes in the canopy (B). Secure the fixture to the screws [AA] using the two cylinder nuts [EE] provided. Tighten securely in place.

Diagram shows the fixture canopy (B) being attached to the mounting plate assembly using screws [AA] and cylinder nuts [EE].

Step 6: Install Lamps

Thread the lamps (not included) into the fixture sockets. Use a 100-watt MAX incandescent medium base lamp, SBCFL or SBLED.

Diagram shows the completed fixture with a lamp being screwed into the socket.

Wiring Diagram

Supply Wires: White, Black

Fixture Wires: White (marked or ribbed), Black (smooth or plain)

Ground Wire: Copper or Green (supply), Copper or Green (fixture)

Connections: Use UL-approved wire nuts or the green ground screw.

Diagrams on page 5 illustrate these connections in English, French, and Spanish.

Warranty Information

Progress Lighting warrants products, when properly installed and under normal conditions of use, to be free from defects in material and workmanship at time of shipment. All warranty claims must be asserted within one year from date of purchase. Customers' sole remedy for a warranty claim shall be limited to repair or replacement of the subject product if it is shown to have been defective. Progress's sole and maximum liability for a defective product shall never exceed the cost of the subject product. All other warranties, express or implied, including implied warranties of MERCHANTABILITY and FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Liability for incidental or consequential damages is excluded. The customer's sole and exclusive remedy is limited to repair or replacement of the subject product at Progress's option, or refund of the purchase price. This warranty and remedy extend only to Progress's customers. Customers are not authorized to extend warranties or remedies on behalf of Progress. Customer is responsible for determining the suitability of products for their use or resale.