Notendahandbók fyrir GSI Electronics Pi RM0 EDGE Essential Raspberry Pi

This document guides the use of Raspberry Pi RM0 as a radio module when integrating into a host product.
The Raspberry Pi RM0 module is designed to be mounted on a PCB in a host product.

Ensure correct placement to maintain radio performance. Only use pre-approved antennas.
Maintain a separation distance of at least 20 cm between the antenna and any other radio transmitter in the same product.

Supply 5V power to the module from a compliant power supply.
Do not alter any part of the board to retain compliance.

The module supports only 2.4 GHz bands with an external patch antenna.
Follow instructions for antenna placement and routing to maintain compliance.

Flýtileiðarvísir

ATH: Þessi handbók veitir ekki nákvæmar uppsetningar-, öryggis- eða notkunarleiðbeiningar.

Please scan the QR Code to access the complete manuals or visit the websíða:

Cumberland: http://www.cumberlandpoultry.com
AP: http://www.automatedproduction.com

The EDGE Essential System is manufactured by GSI Electronics Inc., Canada.

ATH: Leitaðu að 892-00117 to have the electronic version of this document in the manuals search engine.

TÆKNIlegur stuðningur

For Technical support, please call the following phone numbers: For Tech Support in Canada: Dial 1-877-926-2777 and press 9 for English, followed by 1.

For Tech Support in the USA: Dial 1-712-239-1011

MODULE INTEGRATION

Tilgangur

Tilgangur þessa skjals er að veita upplýsingar um hvernig á að nota Raspberry Pi RM0 sem útvarpseiningu þegar hann er samþættur í gestgjafavöru.
Incorrect integration or use may infringe compliance rules, meaning recertification may be required.

Lýsing á einingu

The Raspberry Pi RM0 module has an IEEE 802.11b/g/n/ac 1×1 WLAN module based on the 43455 chip.

The module is designed to be mounted to a PCB into a host product.
The module must be placed in a suitable location to ensure radio performance is not compromised.

The module must be used with a pre-approved antenna only.

Samþætting í vörur
Module and Antenna Placement

A separation distance greater than 20 cm will always be maintained between the antenna and any other radio transmitter if installed in the same product.
Any external power supply of 5V should be supplied to the module and shall comply with the relevant regulations and standards applicable in the country of intended use.
Á engan tímapunkti ætti að breyta neinum hluta stjórnar þar sem það mun ógilda öll núverandi regluverk. Ráðfærðu þig alltaf við faglega eftirlitssérfræðinga um að samþætta þessa einingu í vöru til að tryggja að allar vottanir haldist.

Upplýsingar um loftnet

The module is approved for use with an antenna on the host board and supports only 2.4 GHz bands when used with an external patch antenna (peak gain of 2.6 dBi).
The antenna must be positioned appropriately inside the host product to ensure optimal operation. Do not place it near a metal casing.

Strict adherence to the pre-approved antenna design is required. Any deviation will invalidate the module’s certifications.

The Antenna (Molex Inc., Part Number: 1461530200) is connected to the UFL connector (Taoglas RECE.20279.001E.01), which is connected to the RF switch (Skyworks Part Number: SKY13351-378LF) and directly connected to the RM0 module. Refer to Figure 2-1.

Tilvísun #	Hlutanúmer	Lýsing
1	RECE.20279.001E.01	UFL tengi
2	SKY13351-378LF	RF rofi
3	–	RM0 Module

Do not deviate from any part of the specified antenna list.
The routing to the UFL connector or switch must maintain a 50-ohm impedance with suitable ground stitching vias along the trace route.
The trace length must be minimised by placing the module and antenna close together.
Avoid routing the RF output trace over any other signals or power planes, ensuring it references only ground.
The antenna must be placed at the edge of the PCB with appropriate grounding around its shape.
The antenna consists of the RF feed line (routed with 50 ohms impedance) and a cutout in the ground copper.

To ensure proper functionality, the design’s performance must be plotted, and the peak gain must be calculated to confirm it does not exceed the specified limits stated in this document.
During production, the antenna’s performance must be verified by measuring the radiated output power at a fixed frequency.
To test the final integration, obtain the latest test files frá compliance@raspberrypi.com.

Any deviation from the defined parameters of the antenna trace, as specified in the instructions, requires the host product manufacturer (integrator) to notify the module grantee (Raspberry Pi) of the intended design change.
In such cases, a Class II permissive change application must be filed by the grantee, or the host manufacturer must assume responsibility by applying for a new FCC ID, followed by a Class II Permissive Change application.

YFIRLÝSING FCC

The modular transmitter is FCC-authorised only for the specific rule parts (i.e., FCC transmitter rules) listed on the grant. The host product manufacturer is responsible for ensuring compliance with any other applicable FCC rules not covered by the modular transmitter’s grant of certification. If the grantee markets the product as Part 15 Subpart B compliant (when it includes unintentional-radiator digital circuitry). The final host product must still undergo Part 15 Subpart B compliance testing with the modular transmitter installed.

Lokavörumerking

A label must be affixed to the exterior of all products containing the Raspberry Pi RM0 module. The label must include: “Contains FCC ID: 2AFLZRPIRM0” (for FCC) and “Contains IC: 11880A-RPIRM0” (for ISED).

Raspberry Pi RM0 FCC auðkenni: 2AFLZRPIRM0
Þetta tæki er í samræmi við 15. hluta FCC reglnanna. Rekstur er háður eftirfarandi tveimur skilyrðum:

Þetta tæki má ekki valda truflunum, og
Þetta tæki verður að taka við öllum truflunum, þar með talið truflunum sem geta valdið óæskilegri notkun.

VARÚÐ: Allar breytingar eða breytingar á búnaðinum sem ekki hafa verið samþykktar sérstaklega af þeim aðila sem ber ábyrgð á samræmi gæti ógilt heimild notanda til að nota búnaðinn.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

Snúðu eða færðu móttökuloftnetið aftur.
Auka aðskilnað milli búnaðar og móttakara.

Tengdu búnaðinn við innstungu á annarri hringrás en þeirri sem móttakarinn er tengdur við.
Hafðu samband við söluaðilann eða reyndan útvarps-/sjónvarpstæknimann til að fá aðstoð.

For products available in the USA/Canada, only channels 1 to 11 are available for 2.4 GHz WLAN.
This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter except in accordance with the FCC’s multi-transmitter procedures.

ATH:
FCC yfirlýsing um útsetningu fyrir geislun:

Co-location of this module with other transmitters operating simultaneously must be evaluated using the FCC multi-transmitter procedures.
This device complies with FCC RF radiation exposure limits for an uncontrolled environment. The host device contains an antenna and must be installed to maintain a separation distance of at least 20 cm from all persons.

ISED
Raspberry Pi RM0 IC: 11880A-RPIRM0
Þetta tæki er í samræmi við RSS staðla sem eru undanþegnir leyfi frá Industry Canada. Rekstur er háður eftirfarandi tveimur skilyrðum:

Þetta tæki má ekki valda truflunum, og
Þetta tæki verður að taka við öllum truflunum, þar með talið truflunum sem geta valdið óæskilegri notkun tækisins.

For products available on the USA/Canada market, only channels 1 to 11 are available for 2.4 GHz WLAN. Selection of other channels are not possible.
Þetta tæki og loftnet þess má ekki vera samsett með öðrum sendum nema í samræmi við verklagsreglur IC fjölsenda.

ATH:
Yfirlýsing um IC geislunarváhrif:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum separation distance of 20 cm between the device and all persons.

UPPLÝSINGAR Í SAMANTEKTNING FYRIR OEM

It is the responsibility of the OEM/host product manufacturer to ensure continued compliance with FCC and ISED Canada certification requirements once the module is integrated into the host product. Refer to FCC KDB 996369 D04 for additional information.
The module is subject to the following FCC rule parts: 15.207, 15.209, 15.247, 15.403 and 15.407.

Notendahandbók fyrir gestgjafavöru. Texti
FCC samræmi
Þetta tæki er í samræmi við 15. hluta FCC reglnanna. Rekstur er háður eftirfarandi tveimur skilyrðum:

Þetta tæki má ekki valda skaðlegum truflunum, og
Þetta tæki verður að taka við öllum truflunum sem berast, þar með talið truflunum sem geta valdið óæskilegri notkun.

Snúðu eða færðu móttökuloftnetið aftur.
Auka aðskilnað milli búnaðar og móttakara.

Tengdu búnaðinn við innstungu á annarri hringrás en þeirri sem móttakarinn er tengdur við.
Hafðu samband við söluaðilann eða reyndan útvarps-/sjónvarpstæknimann til að fá aðstoð.

ATH:
FCC yfirlýsing um útsetningu fyrir geislun:

Co-location of this module with other transmitters operating simultaneously must be evaluated using the FCC multi-transmitter procedures.
This device complies with FCC RF radiation exposure limits for an uncontrolled environment. The host device contains an antenna and must be installed to maintain a separation distance of at least 20 cm from all persons.

ISED Kanada samræmi
Þetta tæki er í samræmi við RSS staðla sem eru undanþegnir leyfi frá Industry Canada. Rekstur er háður eftirfarandi tveimur skilyrðum:

Þetta tæki má ekki valda truflunum, og
Þetta tæki verður að taka við öllum truflunum, þar með talið truflunum sem geta valdið óæskilegri notkun tækisins.

For products available in the USA/Canada, only channels 1 to 11 are available for 2.4 GHz WLAN. Selection of other channels are not possible.
This device and its antenna(s) must not be co-located with any other transmitters except in accordance with Industry Canada (IC) multi-transmitter product procedures.

ATH:
Yfirlýsing um IC geislunarváhrif:

This equipment complies with IC RSS-102 radiation exposure limits for an uncontrolled environment. This equipment should be installed and operated with a minimum separation distance of 20 cm between the device and all persons.

Vörumerking gestgjafa
Hýsingarvaran verður að vera merkt með eftirfarandi upplýsingum:

Contains TX FCC ID: 2AFLZRPIRM0”
Contains IC: 11880A-RPIRM0”

Þetta tæki er í samræmi við 15. hluta FCC reglnanna. Rekstur er háður eftirfarandi tveimur skilyrðum:

Þetta tæki má ekki valda skaðlegum truflunum, og
Þetta tæki verður að taka við öllum truflunum sem berast, þar með talið truflunum sem geta valdið óæskilegri notkun.

MIKILVÆGT: The FCC Part 15 text must be placed on the host product unless the product is too small to accommodate a label with the text. It is not acceptable to include the text only in the user guide.

Rafræn merking

The host product can use E-labelling provided it meets the requirements of FCC KDB 784748 D02 E-labelling and ISED Canada RSS-Gen,.

E-labelling applies to the FCC ID, ISED Canada certification number, and FCC Part 15 text.

Breytingar á notkunarskilmálum þessarar einingar
This device has been approved as a mobile device in accordance with FCC and ISED Canada requirements. This means a minimum separation distance of 20 cm must be maintained between the module’s antenna and any person.
Any change in use that reduces the separation distance of ≤20 cm (portable usage) between the module’s antenna and any person is considered a modification to the module’s RF exposure. Such changes require an FCC Class 2 Permissive Change and an ISED Canada Class 4 Permissive Change in accordance with FCC KDB 996396 D01 and ISED Canada RSP-100.

If the device is co-located with multiple antennas, the module may be subject to an FCC Class 2 Permissive Change and an ISED Canada Class 4 Permissive Change in accordance with FCC KDB 996396 D01 and ISED Canada RSP-100.

In accordance with FCC KDB 996369 D03, Section 2.9, test mode configuration information is available from the module manufacturer for the host (OEM) product manufacturer.
Use of any antennas other than those specified in Section 2-4 of this installation guide is subject to the Permissive Change requirements of the FCC and ISED Canada.

Hafðu samband

GSI Electronics Inc.

5200 Armand Frappier Saint-Hubert, QC
Kanada J3Z 1G5
Sími: 1-877-926-2777

Tölvupóstur: mtl_techsupport@agcocorp.com

The information contained in this document is believed to be correct, but GSI Group, LLC accepts no liability for any errors it contains and reserves the right to make changes at any time without notice. Copyright © 2025. The GSI Group, all rights reserved.

Algengar spurningar

Q: Can I use a different antenna than the pre-approved one?

A: No, any deviation from the specified antenna list may require recertification and should be communicated to Raspberry Pi for approval.

Skjöl / auðlindir

GSI Electronics Pi RM0 EDGE Essential Raspberry [pdfNotendahandbók
RPIRM0, 2AFLZRPIRM0, Pi RM0 EDGE Essential Raspberry, Pi RM0, EDGE Essential Raspberry, Essential Raspberry, Raspberry

Heimildir

Notendahandbók

GSI Electronics Pi RM0 EDGE Essential Raspberry

Tæknilýsing

Notkunarleiðbeiningar fyrir vöru