QUIO QU-RDT2-HF Ihe na-agụ ihuenyo LCD mmetụ
Ozi ngwaahịa
- Aha ngwaahịa: QU-RDT2-HF
- Nkọwa: Metụ ahụ igodo LCD ngosi Reader
- Nọmba nlereanya: V0103
Nkọwapụta
| Spec / ihe | QU-RDT2-HF |
|---|---|
| Nyefee ugboro ugboro | 125KHz / 13.56MHz |
| Gụọ Oke | 5-10cm / 2 ~ 6cm |
| Ọnụego Baud | 19,200 bps (4,800 ~ 230,400 bps) |
| Ndakọrịta kaadị | EM ma ọ bụ ISO14443A/B/15693/Mifare |
| Oge ịgụ kaadị | Nkeji 0.1 |
| Ahụigodo | 12 igodo |
| Ihe ngosi LED | 3 LED (RGB) |
| NJ nkwukọrịta | RS485 na Wiegand (26/32/34/42/66 Bits) |
| Ngosipụta LCD | 128×64 ntụpọ (16×4 Char) LCD nwere backlight |
| Mgbochi-Tamper Facility | Wuru n'ime (IR) |
| Ụda ụda | Buzzer arụnyere n'ime ya |
| Ntinye Voltage | 8V ~ 28V DC / 0.5 ~ 2W |
| Akụkụ (W x H x D) | 89.4 x 124 x 12 mm |
Ntuziaka ojiji ngwaahịa
Ndeba nwụnye:
Ngwaahịa a na-eji panel aka. Mgbe ị na-etinye ma na-agbatị skru, soro usoro ndị a:
- Gbanyụọ ngwaọrụ maka opekata mpe 5 sekọnd.
- N'ime oge a, emetụla ogwe aka ma ọ bụ tinye ihe ọ bụla na ya.
- Mgbe oge nkwụsị ọkụ gasịrị, malitegharịa ngwaọrụ ahụ.
Usoro a dị mkpa maka nhazi panel na nhazigharị ọrụ njikwa aka iji hụ na ọrụ ziri ezi na nke ziri ezi.
Ntuziaka QU-RDT2-HF:
Melite:
- Banye: # + # + 0 + 1 (Beep) + PIN + # (PIN ụlọ ọrụ: 1234)
- Wepụ: # + # + 0 + 0 (Beep)
Nhazi ID:
- Buru ụzọ banye, wee mee ntọala ndị a:
- Tọọ ID: # + # + 0 + 2 (Beep) + NJ (NJ ụlọ ọrụ: 1)
- Tọọ ụbọchị na oge: # + # + 0 + 3 (Beep) + YYYYMMDDhhnnss (dịka, 20110129032523 maka Jenụwarị 29, 2011, 03:25:23)
- Gbanwee PIN nbanye: # + # + 0 + 4 (Beep) + PIN ọhụrụ
- Tọọ igbu oge n'azụ: # + # + 0 + 5 (Beep) + Oge (0 maka ọkụ kwụ ọtọ, 1-250 sekọnd)
- Tọọ interface: # + # + 0 + 6 (Beep) + Interface (0 maka Wiegand, 1 maka RS485, 2 maka Wiegand & RS485, Ụlọ ọrụ: 2)
- Tọọ Asụsụ: # + # + 0 + 7 (Beep) + Asụsụ (0 maka Bekee, 1 maka Chinese, Ụlọ ọrụ: 0 – Bekee)
- Tọọ koodu: # + # + 0 + 8 (Beep) + Encode (0 maka UNICODE, 1 maka BIG5, 2 maka GB2312, Ụlọ ọrụ: 0 – UNICODE)
- Tọọ ọnọdụ: # + # + 0 + 9 (Beep) + Klas (0 maka gbanyụọ, 1 maka Kwado, Ụlọ ọrụ: 0 - Gbanyụọ)
Gbanwee ọnọdụ ọrụ:
- Malite ọrụ: # + 1 (Akụkụ)
- rụchaa ọrụ: # + 2 (Akụkụ)
Hapụ n'ọrụ:
- # + 3 (Akụkụ)
Biko buru ụzọ gbanye Ọrụ Ọnọdụ.
Laghachi maka Ọrụ:
- Malite oge gafere: # + 4 (Akụkụ)
- Mechaa oge gafere: # + 5 (Akụ)
- # + 6 (Akụkụ)
Nkọwapụta QU-RDT2-HF
Nkọwa / ihe QU-RDT2-HF
- Nyefee ugboro ugboro 125KHz / 13.56MHz
- Gụọ Oke 5-10cm / 2 ~ 6cm
- Ọnụego Baud 19,200 bps (4,800 ~ 230,400 bps)
- Ndakọrịta kaadị EM ma ọ bụ ISO14443A/B/15693 / Mifare
- Oge ịgụ kaadị Nkeji 0.1
- Ahụigodo 12 igodo
- Ihe ngosi LED 3 LED (RGB)
- Nkwukọrịta RS485 na Wiegand (26/32/34/42/66 Bits)
- ID 0001 ~ 9,999
- Ngosipụta LCD 128×64 ntụpọ (16×4 Char) LCD nwere backlight
- Mgbochi-Tamper Ngwa arụnyere (IR)
- Ụda ụda Buzzer arụnyere n'ime ya
- Okpomọkụ na-arụ ọrụ -10˚C ~ 60˚C
- Ntinye Voltage 8V ~ 28V DC / 0.5 ~ 2W
- Akụkụ (W x H x D) 89.4 x 124 x 12 mm
Ntinye Ntinye
- Ngwaahịa a na-eji panel aka. mgbe ị wụnyere ma mesie skru ndị ahụ, biko gbanyụọ n'elu 5 sekọnd, na n'ime oge a,
- Biko etinyela ihe ọ bụla na akụkụ aka (dịka mkpịsị aka..etc) wee malitegharịa.
- Usoro a bụ maka nhazi panel na mweghachi ọrụ njikwa aka, iji hụ na ọ nwere ike ịrụ ọrụ nke ọma na nke ziri ezi
Ntuziaka QU-RDT2-HF
Kpochapụ:'✱'
Gbanwee ọnọdụ ọrụ:
Biko buru ụzọ gbanye Ọrụ Ọnọdụ.
Ngwa ngwa-Ohm Küpper & Co. GmbH
Cronenfelderstraße 75 | 42349 Wuppertal
Tel: +49 (0) 202 404329 | Fax: +49 (0) 202 404350
E-mail: kontakt@quio-rfid.de Web: www.quio-rfid.de
Akwụkwọ / akụrụngwa
 |
QUIO QU-RDT2-HF Ihe na-agụ ihuenyo LCD mmetụ [pdf] Ntuziaka nwụnye QU-RDT2-HF Touch Keypad LCD Display Reader, QU-RDT2-HF, Touch Keypad LCD Display Reader, Keypad LCD Ngosipụta Ọgụgụ, Ihe Ngosipụta LCD, Onye Ngosipụta Ngosipụta, Onye Na-agụ Ihe |
