QUIO QU-RDT2-HF Touch Keypad LCD Display Reader
ʻIke Huahana
- inoa huahana: QU-RDT2-HF
- wehewehe: E hoʻopā i ka mea heluhelu LCD Display Keypad
- Helu kumu hoʻohālike: V0103
Nā kikoʻī
| Spec / 'ikamu | QU-RDT2-HF |
|---|---|
| Hoʻouna pinepine | 125KHz / 13.56MHz |
| Laulā Heluhelu | 5~10cm / 2~6cm |
| Pākuʻi Baud | 19,200 bps (4,800~230,400 bps) |
| Kāleka Kūlike | EM a i ʻole ISO14443A/B/15693/Mifare |
| Manawa Heluhelu Kāleka | 0.1Sek |
| Papa kī | 12 kī |
| Hōʻike LED | 3 LED (RGB) |
| ID kamaʻilio | RS485 a me Wiegand (26/32/34/42/66 Bits) |
| Hōʻike LCD | 128×64 mau kiko (16×4 Char) LCD me ke kukui hope |
| Kūʻē-Tamper Mea Hana | Hoʻokomo ʻia (IR) |
| Ka Leo Beep | Buzzer i kūkulu ʻia |
| Hoʻokomo Voltage | 8V~28V DC / 0.5 ~ 2W |
| Ana (W x H x D) | 89.4 x 124 x 12 mm |
Nā ʻōlelo hoʻohana huahana
Hoʻokomo ʻia ka ʻōlelo:
Ke hoʻohana nei kēia huahana i kahi pā paʻi. Ke hoʻokomo a hoʻopaʻa ʻia i nā wili, e hahai i kēia mau ʻanuʻu:
- E hoʻopau i ka hāmeʻa no ka liʻiliʻi he 5 kekona.
- I loko o kēia manawa, mai hoʻopā i ka pā paʻi a kau i kekahi mea ma luna.
- Ma hope o ka pau ʻana o ka mana, hoʻomaka hou i ka hāmeʻa.
Pono kēia kaʻina hana no ka calibration panel a me ka helu hou ʻana o ka hana mana paʻi e hōʻoia i ka hana pololei a pololei.
Nā ʻōlelo kuhikuhi QU-RDT2-HF:
Hoʻonoho:
- Komo: # + # + 0 + 1 (Beep) + PIN + # (PIN hale hana: 1234)
- Haʻalele: # + # + 0 + 0 (Beep)
Hoʻonohonoho ID:
- E komo mua, a laila e hana i kēia mau hoʻonohonoho:
- E hoʻonoho i ka ID: # + # + 0 + 2 (Beep) + ID (Factory ID: 1)
- Hoʻonohonoho i ka lā a me ka manawa: # + # + 0 + 3 (Beep) + YYYYMMDDhhnnss (e laʻa, 20110129032523 no Ianuali 29, 2011, 03:25:23)
- Hoʻololi i ka PIN komo ʻana: # + # + 0 + 4 (Beep) + PIN hou
- E hoʻopaʻa i ka lohi o ke kukui hope: # + # + 0 + 5 (Beep) + Manawa (0 no ka māmā mau, 1-250 kekona)
- E hoʻonohonoho i ka Interface: # + # + 0 + 6 (Beep) + Interface (0 no Wiegand, 1 no RS485, 2 no Wiegand & RS485, Hale Hana: 2)
- E hoʻonohonoho i ka ʻōlelo: # + # + 0 + 7 (Beep) + ʻŌlelo (0 no ka ʻōlelo Pelekania, 1 no ka Pākē, Hale Hana: 0 – English)
- E hoʻopaʻa i ke code: # + # + 0 + 8 (Beep) + Encode (0 no UNICODE, 1 no BIG5, 2 no GB2312, Hale Hana: 0 – UNICODE)
- Hoʻonoho i ke kūlana: # + # + 0 + 9 (Beep) + Papa (0 no Disable, 1 no Enable, Factory: 0 – Hoʻopau)
Hoʻololi i ke kūlana hana:
- E hoʻomaka i ka hana: # + 1 (Beep)
- Hoʻopau i ka hana: # + 2 (Beep)
Haʻalele i ka hana:
- # + 3 (Beep)
E ʻoluʻolu e hoʻā mua i ka Hana Kūlana.
Back for Duty:
- Hoʻomaka i ka hola ʻoi: # + 4 (Beep)
- Hoʻopau Hoʻopau manawa: # + 5 (Beep)
- # + 6 (Beep)
QU-RDT2-HF kiko'ī
Mea kiko'ī / 'ikamu QU-RDT2-HF
- Hoʻouna pinepine 125KHz / 13.56MHz
- Laulā Heluhelu 5~10cm / 2~6cm
- Pākuʻi Baud 19,200 bps (4,800~230,400 bps)
- Kāleka Kūlike EM a i ʻole ISO14443A/B/ 15693 / Mifare
- Manawa Heluhelu Kāleka 0.1Sek
- Papa kī 12 kī
- Hōʻike LED 3 LED (RGB)
- Kūkākūkā RS485 a me Wiegand (26/32/34/42/66 Bits)
- ID 0001 ~ 9,999
- Hōʻike LCD 128×64 mau kiko (16×4 Char) LCD me ke kukui hope
- Kūʻē-Tamper Hāʻawi ʻia i loko (IR)
- Ka Leo Beep Buzzer i kūkulu ʻia
- Ka Mahana Hana -10˚C ~ 60˚C
- Hoʻokomo Voltage 8V~28V DC / 0.5 ~ 2W
- Anana (P x H x D) 89.4 x 124 x 12 mm
Kaha hoʻonoho
- Hoʻohana kēia huahana i ka pā paʻi. i kou hoʻokomo ʻana a hoʻopaʻa i nā wili, e ʻoluʻolu POWER OFF ma luna o 5 kekona, a i kēia manawa,
- E ʻoluʻolu mai kau i kekahi mea ma ka pā paʻi (eg Finger..etc) a laila hoʻomaka hou.
- ʻO kēia kaʻina hana no ka calibration panel a me ka helu hou ʻana i ka hana mana paʻi, e hōʻoia i hiki ke hana pololei a pololei
QU-RDT2-HF kuhikuhi
Akaka：'✱ '
Hoʻololi i ke kūlana hana:
E ʻoluʻolu e hoʻā mua i ka Hana Kūlana.
Quick-Ohm Küpper & Co. GmbH
Cronenfelderstraße 75 | 42349 Wuppertal
Tel: +49 (0) 202 404329 | Fax: +49 (0) 202 404350
E-mail: kontakt@quio-rfid.de Web: www.quio-rfid.de
Palapala / Punawai
 |
QUIO QU-RDT2-HF Touch Keypad LCD Display Reader [pdf] Alakaʻi hoʻokomo QU-RDT2-HF Mea Heluhelu LCD Papa Kipad, QU-RDT2-HF, Mea Heluhelu Papa Kipi, Mea Heluhelu LCD, Mea Heluhelu LCD, Mea Heluhelu. |
