FTI-STK1 Wrx Std Key Mt

FTI-STK1: Nkwadebe ụgbọ ala na ndetu mkpuchi

Mee	Nlereanya	Afọ	Wụnye	IKE	IMO	BCM	Njide	M/O Mgbanwe
Subaru	WRX STD KEY MT (Canada)	2022-23	Ụdị 5	20-Pin	B	DSD	Lt. Green	Green White/Blue

Vehicle Notes
Ụgbọ ala ahụ kpuchiri ekpuchi na-eji ngwa ngwa BLADE-AL-SUB9 yana ngwa ndị a chọrọ: Weblink Hub and ACC-RFID1. Update and activate the controller firmware. Follow the instructions for RFID programming before attempting to program the vehicle’s BLADE module.

IKE
CAN connections (Type 5) are made to the 20-pin BCM adapter and require connecting the white connectors to the marker [D] in the illustration.

Immobilizer
IMMO type B requires connecting the black and white 2-pin connectors to the marker [C] in the illustration.

Ọkụ
Parking lights are pre-cabled in the FTI-STK1 harness. Replace the green/white harness connector with the white/blue harness connector.

ACC-RFID1 (chọrọ)
The SUB9 firmware does not provide immobilizer data, so an ACC-RFID1 is required for remote start.

Clutch (2nd Start)
The FTI-STK1 harness is pre-cabled with a 2nd START red/black wire (required in “TYPE 5”), connected to the 2nd position of the 10-pin connector of the ignition switch, located on the clutch pedal. Make the configuration changes listed below to enable output. Ensure this is necessary to avoid unnecessary cuts.

M/O Mgbanwe
CM7: The bridge 3 was moved to the START position. CMX: HCP #1, configuration [2] (2nd START).

Ịdọ aka ná ntị

Ịdọ aka ná ntị 1: Program ACC-RFID1 before attempting to program the BLADE module in the vehicle.
Ịdọ aka ná ntị 2: Ensure all 2-pin connections, both used and unused, are connected to the main harness body.

FTI-STK1 – Installation and Configuration Notes

• A: Ngwa achọrọ
• B: Achọrọ ihe nkwụnye
• C: Required Configuration (Type B IMMO)
• D: Enweghị njikọ
• E: Connection Required

Mkpuchi ọrụ

Ọrụ	Ọnọdụ
Data Immobilizer	Dị
Oti mkpu OEM ogwe aka	Dị
Wepụ ngwa oti mkpu OEM	Dị
Mkpọchi ụzọ	Dị
Mkpọghe ụzọ	Dị
Mkpọghe ụzọ	Dị
Mwepụta akpati/ọnụ	Dị
Pịa Mmepụta	Dị
Ọnọdụ ọnụ ụzọ	Dị
Ọnọdụ akpati	Dị
Ọnọdụ breeki	Dị
Ọnọdụ E-Brake	Dị
Njikwa mkpu A/M sitere na OEM Remote	Dị
Njikwa A/M RS sitere na OEM Remote	Dị
Njikwa ọkụ akpaaka	Dị

Ntọala jumper
FT-DAS Required for manual transmission. Both Red & Red/White MUST be connected with higher current application.

Ọwa mmepụta CMX dị ugbu a nwere ike ime (+).

• HCP #1 - Ìhè ụgbọala
• HCP #2 - Ngwa
• HCP # 3 - mgbanye ọkụ

[2] 2ND START, [3] 2ND IGNITION, [4] 2ND ACCESSORY

Ntuziaka nwụnye

Ntinye katrij

1. Tinye katrij n'ime otu. Bọtịnụ ọkwa n'okpuru LED.
2. Njikere maka Usoro Mmemme Module.

Usoro mmemme modul

1. Maka nrụnye a, ihe Webnjikọ HUB chọrọ.
2. Wepu igodo OEM 1 na keychain.
3. Debe igodo igodo ndị ọzọ opekata mpe otu ụkwụ site na ya Webnjikọ HUB. Ọdịda irube isi nwere ike bute mmebi nke mkpịsị ugodi igodo ndị ọzọ ma ọ bụ tinye aka na usoro ọgụgụ igodo fob.
4. Gbanyụọ modul ahụ site na iji Webnjikọ HUB. Soro ntuziaka na ihuenyo ka ịmechaa usoro ọgụgụ igodo fob.
5. Iji igodo OEM 1, tụgharịa igodo gaa na ọnọdụ ON.
6. Chere, LED ga-atụgharị na-acha anụnụ anụnụ maka sekọnd 2.
7. Gbanyụọ igodo gaa na ọnọdụ.
8. Usoro mmemme modul agwụla.

Koodu mperi mmemme LED

• 1x RED = Cannot communicate with RFID or immobilizer data.
• 2x RED = No CAN activity. Check CAN cable connections.
• 3x RED = Ignition not detected. Check ignition and CAN cable connections.
• 4x RED = Achọpụtaghị diode mgbanye ọkụ achọrọ.

FAQ

• Kedu ebumnuche ACC-RFID1?
  ACC-RFID1 is required because the SUB9 firmware does not provide immobilizer data, which is necessary for remote start.
• Gịnị kpatara ya Weblink HUB required?
  Nke Weblink HUB is needed for flashing the module and completing the keyfob reading process.
• What should I do if the LED flashes red?
  Rụtụ aka na ngalaba Koodu njehie mmemme mmemme LED iji chọpụta okwu dabere na ọnụọgụ ọkụ na-acha ọbara ọbara.
• How do I ensure proper connection of the harness?
  Ensure all 2-pin connections, both used and unused, are connected to the main harness body.

FTI-STK1:

• FT-DAS chọrọ maka nnyefe akwụkwọ ntuziaka.
• A ghaghị ijikọ abụọ Red & Red / White na ngwa dị elu dị ugbu a.

FTI-STK1 – AL-SUB9 – Type 5 2022-23 Subaru WRX STD KEY MT (CA)

Mgbakọ mgbanaka ọkụ

Mwube AKWRKWỌ

1. Tinye katrij n'ime otu. Bọtịnụ ọkwa n'okpuru LED.
2. Njikere maka Usoro Mmemme Module.

Usoro mmemme MODULE

1. Maka nrụnye a, ihe Webnjikọ HUB chọrọ.
2. Wepu igodo OEM 1 na keychain.
3. Debe igodo igodo ndị ọzọ opekata mpe otu ụkwụ site na ya Webnjikọ HUB. Ọdịda irube isi nwere ike bute mmebi nke mkpịsị ugodi igodo ndị ọzọ ma ọ bụ tinye aka na usoro ọgụgụ igodo fob.
   Gbanyụọ modul ahụ site na iji Webnjikọ HUB. Soro ntuziaka dị na ihuenyo ka ịmechaa usoro ọgụgụ isi igodo.
4. Ịdọ aka ná ntị:
   Ejila bọtịnụ mmemme modul.
   Connect power fi rst. Connect module to vehicle.
5. Iji igodo OEM 1, tụgharịa igodo gaa na ọnọdụ ON.
6. Wait, LED will turn solid BLUE for 2 second  .
7. Gbanyụọ igodo gaa na ọnọdụ.
8. Usoro mmemme modul agwụla.

WWW.IDATALINK.COM
Automotive Data Solutions Inc. © 2020

Akwụkwọ / akụrụngwa

	FTI-STK1 Wrx Std Key Mt [pdf] Ntuziaka nwụnye SUB9, AL-SUB9, FTI-STK1 Wrx Std Key Mt, FTI-STK1, Wrx Std Key Mt, Std Key Mt, Key Mt, Mt
	FTI-STK1 Wrx Std Key Mt [pdf] Ntuziaka nwụnye DL-SUB9, agụba-AL-SUB9, ACC-RFID1, FTI-STK1 Wrx Std Key Mt, FTI-STK1, Wrx Std Key Mt, Std Key Mt, Mt
	FTI-STK1 Wrx Std Key Mt [pdf] Ntuziaka nwụnye Ụdị 6, Ụdị 5, FTI-STK1 Wrx Std Key Mt, FTI-STK1, Wrx Std Key Mt, Std Key Mt, Key Mt, Mt

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ