UNO R3 SMD Micro Controller
Akwụkwọ ntuziaka ngwaahịa
SKU: A000066
Akwụkwọ ntuziaka
Nkọwa
Arduino UNO R3 bụ bọọdụ zuru oke iji mara ngwa elektrọnik na nzuzo. Igwe njikwa microcontroller a nwere ATmega328P ama ama yana ATMEga 16U2 Processor.
Bọdụ a ga-enye gị ọmarịcha ahụmịhe mbụ n'ime ụwa Arduino.
Ebe ebumnuche:
Onye rụpụtara, mmeghe, ụlọ ọrụ
Atụmatụ
Ihe nhazi ATMEga328P
- Ebe nchekwa
• CPU AVR ruo 16 MHz
• Flash 32KB
• 2KB SRAM
• 1KB EEPROM - Nchekwa
• Ike na nrụpụta (POR)
• Nchọpụta agba aja aja (BOD) - Akụkụ
• 2x 8-bit Timer/Counter nwere ndebanye oge raara onwe ya nye wee tulee ọwa
• 1x 16-bit Timer/Counter nwere ndekọ oge raara onwe ya nye, ntinye ntinye na tulee ọwa
• 1x USART nwere ọnụọgụ baud ọnụ ọgụgụ na-emepụta ihe na nchọpụta mmalite nke etiti
• Onye na-ahụ maka 1x/Mpaghara Serial Peripheral Interface (SPI)
• 1x Dual mode control/mperipheral I2C
• 1x Analog Comparator (AC) nwere ntinye ntụaka nwere ike itolite
• Ngụ oge nche nwere oscillator on-chip dị iche
• Ọwa PWM isii
• Kwụsị ma teta na mgbanwe pin - Ihe nhazi ATMEga16U2
• Microcontroller dabere na 8-bit AVR® RISC - Ebe nchekwa
• 16 KB ISP Flash
• 512B EEPROM
• 512B SRAM
• debugWIRE interface maka nbipu na-mpịakọta na mmemme - Ike
• 2.7-5.5 volts
The Board
1.1 Ngwa Examples
bọọdụ UNO bụ ngwaahịa ọkọlọtọ nke Arduino. N'agbanyeghị ma ọ bụrụ na ị bụ onye ọhụrụ na ụwa nke ngwá electronic ma ọ bụ na ị ga-eji UNO dị ka ngwá ọrụ maka ebumnuche agụmakwụkwọ ma ọ bụ ọrụ metụtara ụlọ ọrụ.
Ntinye mbụ na ngwa eletrọnịkị: Ọ bụrụ na nke a bụ ọrụ izizi gị n'ime koodu koodu na ngwa eletrọnịkị, malite na bọọdụ anyị kacha eji na edekọ; Arduino UNO. Ejiri ya na ihe nrụpụta ATmega328P a ma ama, ntinye ntinye / ntinye dijitalụ 14, ntinye analog 6, njikọ USB, nkụnye eji isi mee ICSP na bọtịnụ nrụpụta. Bọdụ a gụnyere ihe niile ị ga-achọ maka ahụmịhe izizi na Arduino.
Ụlọ ọrụ mmepe ọkọlọtọ ọkọlọtọ: Iji bọọdụ Arduino UNO na ụlọ ọrụ, enwere ụlọ ọrụ dị iche iche na-eji bọọdụ UNO dị ka ụbụrụ maka PLC ha.
Ebumnuche agụmakwụkwọ: Ọ bụ ezie na bọọdụ UNO anọnyere anyị ihe dị ka afọ iri, a ka na-eji ya eme ihe maka ebumnuche agụmakwụkwọ dị iche iche na ọrụ sayensị. Ọkọlọtọ dị elu nke bọọdụ ahụ na arụmọrụ kachasị mma na-eme ka ọ bụrụ nnukwu akụrụngwa iji weghara ozugbo site na sensọ yana ịkpalite ngwa ụlọ nyocha dị mgbagwoju anya iji kpọtụrụ ndị gara aga.amples.
1.2 Ngwaahịa metụtara
- Ngwa mmalite
- Tinkerkit Braccio Robot
- Example
Ogo
2.1 Ọnọdụ ọrụ akwadoro
| Akara | Nkọwa | Min | Oke |
| Oke thermal Conservative maka bọọdụ dum: | -40 Celsius (-40°F) | 85 Celsius C (185°F) |
IHE: Na oke okpomọkụ, EEPROM, voltage regulator, na kristal oscillator, nwere ike ọ gaghị arụ ọrụ dịka a tụrụ anya n'ihi oke ọnọdụ okpomọkụ
2.2 Ike oriri
| Akara | Nkọwa | Min | Ụdị | Oke | Nkeji |
| VINMax | Oke ntinye voltage sitere na VIN pad | 6 | – | 20 | V |
| VUSBMax | Oke ntinye voltage site na njikọ USB | – | – | 5.5 | V |
| PMax | Oriri ike kacha | – | xx | mA |
Arụ ọrụ gafereview
3.1 Board Topology
N'elu view
| Ref. | Nkọwa | Ref. | Nkọwa |
| X1 | Igwe ọkụ eletrik 2.1 × 5.5mm | U1 | Onye na-achịkwa SPX1117M3-L-5 |
| X2 | Njikọ USB B | U3 | ATMEGA16U2 |
| PC1 | EEE-1EA470WP 25V SMD Capacitor | U5 | LMV358LIST-A.9 IC |
| PC2 | EEE-1EA470WP 25V SMD Capacitor | F1 | Chip Capacitor, Njupụta dị elu |
| D1 | CGRA4007-G ihe ndozi | ICSP | Njikọ nkụnye eji isi mee (site na oghere 6) |
| J-ZU4 | ATMEGA328P | ICSP1 | Njikọ nkụnye eji isi mee (site na oghere 6) |
| Y1 | ECS-160-20-4X-DU Oscillator |
3.2 processor
Main Processor bụ ATmega328P na-agba ọsọ na tp 20 MHz. Ejikọrọ ọtụtụ ntụtụ ya na nkụnye eji isi mee ndị dị na mpụga, mana ụfọdụ ka edobere maka nkwurịta okwu n'ime ya na eriri USB coprocessor.
3.3 Osisi Ike
Osisi ike
Akụkọ mgbe ochie:
| Akụkụ |  Ike I / O |
 Ụdị ntụgharị |
 Max Ugbu a |
 Voltage Oke |
Ọrụ Board
4.1 Mmalite – IDE
Ọ bụrụ na ịchọrọ ịme mmemme Arduino UNO gị mgbe ị na-anọghị n'èzí, ịkwesịrị ịwụnye IDE Arduino Desktop [1] Iji jikọọ Arduino UNO na kọmputa gị, ị ga-achọ eriri USB Micro-B. Nke a na-enyekwa ike na osisi ahụ, dị ka LED gosipụtara.
4.2 Mmalite – Arduino Web Onye nchịkọta akụkọ
Bọdụ Arduino niile, gụnyere nke a, na-arụ ọrụ nke ọma na Arduino Web Editor [2], site na ịwụnye ngwa mgbakwunye dị mfe.
Arduino Web A na-akwado onye nchịkọta akụkọ n'ịntanetị, ya mere ọ ga-adị ọhụrụ mgbe niile site na njirimara na nkwado maka bọọdụ niile. Soro [3] ka ịmalite itinye koodu na ihe nchọgharị wee bulite ihe osise gị na bọọdụ gị.
4.3 Mmalite – Arduino IoT igwe ojii
A na-akwado ngwaahịa Arduino IoT niile na Arduino IoT Cloud nke na-enye gị ohere ịbanye, eserese na nyochaa data sensọ, kpalite ihe omume, wee rụzie ụlọ ma ọ bụ azụmahịa gị.
4.4 Sampna Sketches
SampEnwere ike ịhụ ihe osise maka Arduino XXX ma na “Examples” menu na Arduino IDE ma ọ bụ na ngalaba “Akwụkwọ” nke Arduino Pro websaịtị [4]
4.5 Ngwa ntanetị
Ugbu a na ị gafere isi ihe ị nwere ike ime na bọọdụ ị nwere ike ịchọpụta ohere na-adịghị agwụ agwụ ọ na-enye site na ịlele ọrụ ndị na-akpali akpali na Project Hub [5], Arduino Library Reference [6] na ụlọ ahịa dị n'ịntanetị [7] ebe. ị ga-enwe ike iji sensọ, actuators na ndị ọzọ mejuo osisi gị
4.6 Board Iweghachite
Bọdụ Arduino niile nwere ihe nrụnye bootloader nke na-enye ohere iji eriri USB na-ebunye bọọdụ ahụ. Ọ bụrụ na eserese kpuchiri ihe nrụpụta na bọọdụ ahụ enweghị ike iru ọzọ site na USB, ọ ga-ekwe omume ịbanye ọnọdụ bootloader site na ịpị bọtịnụ nrụpụta ugboro abụọ ozugbo ọ gbasịrị.
Pinouts njikọ
5.1 JANALOG
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | NC | NC | Ejikọtaghị ya |
| 2 | IOREF | IOREF | Ntụaka maka mgbagha dijitalụ V - ejikọrọ na 5V |
| 3 | Tọgharia | Tọgharia | Tọgharia |
| 4 | + 3V3 | Ike | + 3V3 ụgbọ okporo ígwè |
| 5 | +5V | Ike | + 5V ụgbọ okporo ígwè |
| 6 | GND | Ike | Ala |
| 7 | GND | Ike | Ala |
| 8 | VIN | Ike | Voltage Ntinye |
| 9 | AO | Analog/GPIO | Ntinye Analog 0/GPIO |
| 10 | Al | Analog/GPIO | Ntinye Analog 1/GPIO |
| 11 | A2 | Analog/GPIO | Ntinye Analog 2/GPIO |
| 12 | A3 | Analog/GPIO | Ntinye Analog 3/GPIO |
| 13 | A4/SDA | Ntinye Analog/12C | Ntinye Analog 4/12C ahịrị data |
| 14 | A5/SCL | Ntinye Analog/12C | Ntinye Analog 5/12C ahịrị elekere |
5.2 JDIGITAL
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | DO | Dijitalụ/GPIO | Ntụtụ dijitalụ 0/GPIO |
| 2 | D1 | Dijitalụ/GPIO | Ntụtụ dijitalụ 1/GPIO |
| 3 | D2 | Dijitalụ/GPIO | Ntụtụ dijitalụ 2/GPIO |
| 4 | D3 | Dijitalụ/GPIO | Ntụtụ dijitalụ 3/GPIO |
| 5 | D4 | Dijitalụ/GPIO | Ntụtụ dijitalụ 4/GPIO |
| 6 | DS | Dijitalụ/GPIO | Ntụtụ dijitalụ 5/GPIO |
| 7 | D6 | Dijitalụ/GPIO | Ntụtụ dijitalụ 6/GPIO |
| 8 | D7 | Dijitalụ/GPIO | Ntụtụ dijitalụ 7/GPIO |
| 9 | D8 | Dijitalụ/GPIO | Ntụtụ dijitalụ 8/GPIO |
| 10 | D9 | Dijitalụ/GPIO | Ntụtụ dijitalụ 9/GPIO |
| 11 | SS | Dijitalụ | SPI Mgbawa Họrọ |
| 12 | MOSI | Dijitalụ | SPI1 Main Out Secondary In |
| 13 | MISO | Dijitalụ | SPI Main Na Secondary Out |
| 14 | SCK | Dijitalụ | Mmepụta elekere nsonso nke SPI |
| 15 | GND | Ike | Ala |
| 16 | AREF | Dijitalụ | Analog ntụaka voltage |
| 17 | A4/SD4 | Dijitalụ | Ntinye Analog 4/12C ahịrị data (nke oyiri) |
| 18 | A5/SDS | Dijitalụ | Ntinye Analog 5/12C ahịrị elekere (nke oyiri) |
5.3 Ozi igwe
5.4 Ngosipụta bọọdụ & oghere nrịgo
Asambodo
6.1 Nkwupụta nke Nkwekọrịta CE DoC (EU)
Anyị na-ekwupụta n'okpuru ọrụ anyị naanị na ngwaahịa ndị dị n'elu kwekọrọ na ihe ndị dị mkpa nke ntuziaka EU na-esote ya mere tozuru oke maka mmegharị n'efu n'ime ahịa nke nwere European Union (EU) na European Economic Area (EEA).
| Ntuziaka ROHS 2 2011/65/EU | ||
| Kwekọrọ na: | EN50581:2012 | |
| Ntuziaka 2014/35/EU. (LVD) | ||
| Kwekọrọ na: | EN 60950- 1:2006/A11:2009/A1:2010/Al2:2011/AC:2011 | |
| Ntuziaka 2004/40/EC & 2008/46/EC EMF | & 2013/35/EU, | |
| Kwekọrọ na: | EN 62311:2008 |
6.2 Nkwuwapụta Nkwekọrịta na EU RoHS & REACH 211 01/19/2021
bọọdụ Arduino kwekọrọ na RoHS 2 Directive 2011/65/EU nke European nzuko omeiwu na RoHS 3 Directive 2015/863/EU nke Council of 4 June 2015 na mmachi nke ojiji nke ụfọdụ ize ndụ ihe na ngwa eletriki na eletrọnịkị.
| Ihe | Oke kacha (ppm) |
| Ndu (Pb) | 1000 |
| Ogwugwu (Cd) | 100 |
| Ebere (Hg) | 1000 |
| Chromium Hexavalent (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis (2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Mwepu: Ọnweghị mpụ a na-ekwu.
Boards Arduino na-akwado nke ọma na ihe ndị metụtara European Union Regulation (EC) 1907/2006 gbasara ndebanye aha, nyocha, ikike na mmachi nke kemịkalụ (REACH). Anyị na-ekwupụta na ọ nweghị nke SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), Ndepụta ndị Candidate nke ihe dị oke mkpa maka ikike nke ECHA wepụtara ugbu a, dị na ngwaahịa niile (yana ngwugwu) n'ogo zuru oke na mkpokọta nha ma ọ bụ karịa 0.1%. Dị ka ihe ọmụma anyị si mara, anyị na-ekwupụtakwa na ngwaahịa anyị enweghị ihe ọ bụla e depụtara na "Ndepụta ikike" (Annex XIV nke ụkpụrụ REACH) na
Ihe nke Nchegbu Dị Elu (SVHC) n'ụdị ọ bụla dị mkpa dị ka akọwapụtara n'akwụkwọ Annex XVII of Candidate list nke ECHA (European Chemical Agency) 1907/2006/EC bipụtara.
6.3 Nkwuwapụta mineral na esemokwu
Dị ka onye na-eweta ihe elektrọnik na eletriki eletrik zuru ụwa ọnụ, Arduino maara ọrụ anyị na-ahụ maka iwu na ụkpụrụ gbasara Mineral Conflict, kpọmkwem Dodd-Frank Wall Street Reform and Consumer Protection Act, Nkebi 1502. Arduino anaghị ebute ma ọ bụ hazie esemokwu ozugbo. mineral dị ka Tin, Tantalum, Tungsten, ma ọ bụ ọla edo. Ngwakọta mineral ndị na-ese okwu dị n'ime ngwaahịa anyị n'ụdị ihe na-ere ahịa, ma ọ bụ dị ka akụrụngwa na alloys ọla. Dịka akụkụ nke mbọ anyị kwesịrị ekwesị Arduino akpọtụrụla ndị na-ebubata akụrụngwa n'ime ụdọ ọkọnọ anyị iji chọpụta na ha nọgidere na-agbaso ụkpụrụ ahụ. Dabere na ozi enwetara ugbu a, anyị na-ekwupụta na ngwaahịa anyị nwere Mineral Conflict sitere na mpaghara enweghị nsogbu.
FCC ịkpachara anya
Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị otu na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ngwa ahụ.
Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.
Nkwupụta Mkpughe Radiation FCC RF:
- Agaghị ejikọta ihe nnyefe a ma ọ bụ na-arụ ọrụ na njikọ antenna ma ọ bụ nnyefe ọ bụla ọzọ.
- Ngwa a na-akwado oke mkpughe radieshon RF ewepụtara maka gburugburu enweghị njikwa.
- Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na anya kacha nta 20cm n'etiti radiator & ahụ gị.
Igbo: Akwụkwọ ntuziaka onye ọrụ maka ngwa redio enweghị ikike ga-enwe ọkwa ndị a ma ọ bụ nha nhata n'ebe pụtara ìhè n'ime akwụkwọ ntuziaka onye ọrụ ma ọ bụ ọzọ na ngwaọrụ ma ọ bụ ha abụọ. Ngwaọrụ a na-akwado ụkpụrụ (s) RSS enweghị ikike ụlọ ọrụ Canada. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla, gụnyere nnyonye anya nwere ike bute ọrụ ngwaọrụ ahụ achọghị.
Ịdọ aka ná ntị IC SAR:
Asụsụ a kwesịrị ịwụnye ma rụọ ọrụ ya na anya kacha nta 20 cm n'etiti radiator na ahụ gị.
Ihe dị mkpa: Ọnọdụ okpomọkụ nke EUT enweghị ike ịgafe 85 ℃ ma ghara ịdị ala karịa -40 ℃.
Site na nke a, Arduino Srl na-ekwupụta na ngwaahịa a kwekọrọ na ihe ndị dị mkpa chọrọ yana ndokwa ndị ọzọ dị mkpa nke Ntuziaka 2014/53/EU. Ekwenyere ka ejiri ngwaahịa a na mba ndị otu EU niile.
Ozi ụlọ ọrụ
| Aha Ụlọ Ọrụ | Arduino Srl |
| Adreesị ụlọ ọrụ | Site na Andrea Appiani 25 20900 MONZA Italy |
Akwụkwọ ntụaka
| Ntụaka | Njikọ |
| Ardulno IDE (Desktọpụ) | https://www.arduino.cden/Main/Software |
| Ardulno IDE (igwe ojii) | https://create.arduino.cdedltor |
| Cloud IDE na-amalite | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduinoweb-editor-4b3e4a |
| Ardulno Pro Websaịtị | https://www.arduino.cc/pro |
| Hub Project | https://create.arduino.cc/projecthub?by=part&part_Id=11332&sort=trending |
| Ntụaka ụlọ akwụkwọ | https://www.arduino.cc/reference/en/ |
| Ụlọ ahịa dị n'ịntanetị | https://store.ardulno.cc/ |
Akụkọ ngbanwe
| Ụbọchị | Ndozigharị | Mgbanwe |
| xx/06/2021 | 1 | Mwepụta akwụkwọ data |
Arduino® UNO R3
gbanwere: 25/02/2022
Akwụkwọ / akụrụngwa
 |
ARDUINO UNO R3 SMD Micro Controller [pdf] Akwụkwọ ntuziaka UNO R3, SMD Micro Controller, UNO R3 SMD Micro Controller, Micro Controller, Controller |
