ARDUINO ABX00069 Nano BLE Sense Rev2 Akwụkwọ ntuziaka onye ọrụ ARM Cortex-M4
Nkọwa
Nke Arduino Nano 33 BLE Sense Rev2* bụ obere modul nwere modul NINA B306, dabere na
Nordic nRF52480 nwere Cortex M4F. BMI270 na BMM150 jikọtara ọnụ na-enye 9 axis IMU. Enwere ike itinye modul ahụ dị ka akụrụngwa DIP (mgbe ị na-ebunye isi ntụtụ), ma ọ bụ dị ka akụrụngwa SMT, na-ere ya ozugbo site na paịlị nke castellated.
Nordic nRF52480 nwere Cortex M4F. BMI270 na BMM150 jikọtara ọnụ na-enye 9 axis IMU. Enwere ike itinye modul ahụ dị ka akụrụngwa DIP (mgbe ị na-ebunye isi ntụtụ), ma ọ bụ dị ka akụrụngwa SMT, na-ere ya ozugbo site na paịlị nke castellated.
Ngwaahịa Arduino Nano 33 BLE Sense Rev2 nwere SKU abụọ:
- Enweghị nkụnye eji isi mee (ABX00069)
- Ya na nkụnye eji isi mee (ABX00070)
Mpaghara ebumnuche
Onye mepụtara, nkwalite, ngwa IoT
Atụmatụ
- NINA B306 Modul♦ Nhazi
♦ 64 MHz Arm® Cortex®-M4F (ya na FPU)
♦ MB Flash + 256 KB RAM♦ Bluetooth® 5 multiprotocol redio
♦ 2 Mbps
♦ CSA #2
♦ Mgbasa mgbasa ozi
♦ Ogologo Ogologo
♦ +8 dBm TX ike
♦ -95 dBm uche
♦ 4.8 mA na TX (0 dBm)
♦ 4.6 mA na RX (1 Mbps)
♦ Balun jikọtara ọnụ na mmepụta 50 Ω nwere otu njedebe
♦ IEEE 802.15.4 nkwado redio
♦ Eriri
♦ Zigbee♦ Peripherals
♦ USB 12Mbps zuru oke
♦ NFC-A tag
♦ Arm CryptoCell CC310 nchekwa subsystem
♦ QSPI/SPI/TWI/I²S/PDM/QDEC
♦ Nnukwu ọsọ 32 MHz SPI
♦ Quad SPI interface 32 MHz
♦ EasyDMA maka oghere dijitalụ niile
♦ 12-bit 200 kps ADC
♦ 128 bit AES/ECB/CCM/AAR ngalaba-processor - BMI 270 6-axis IMU (Accelerometer na Gyroscope)
♦ 16-bit
♦ 3-axis accelerometer nwere ± 2g/± 4g/±8g/±16g nso
gyroscope 3-axis nwere ± 125dps/± 250dps/±500dps/±1000dps/±2000dps nso - BMM150 3-axis IMU (Magnetometer)
♦ 3-axis dijitalụ geomagnetic sensọ
♦ 0.3μT mkpebi
♦ ± 1300μT (x, y-axis), ± 2500μT (z-axis) - LPS22HB (Barometer na ihe mmetụta okpomọkụ)
♦ 260 ruo 1260 hPa oke nrụgide zuru oke na nkenke 24 bit
♦ Ikike nrịbama dị elu: 20x zuru oke
♦ Nkwụghachi ụgwọ okpomọkụ agbakwunyere
♦ Mmepụta data okpomọkụ 16-bit
♦ 1 Hz ka 75 Hz mmepụta ọnụego data nkwụsị ọrụ: Njikere data, ọkọlọtọ FIFO, ọnụ ụzọ nrụgide - HS3003 Okpomọkụ & iru mmiri mmetụta
♦ 0-100% iru mmiri oke
♦ Ikike iru mmiri: ± 1.5% RH, nke a na-ahụkarị (HS3001, 10 ruo 90% RH, 25°C)
♦ Okpomọkụ ihe mmetụta ziri ezi: ± 0.1 ° C, ahụkarị
♦ Ruo 14-bit iru mmiri na data mmepụta okpomọkụ - APDS-9960 (Digital nso, ọkụ gburugburu, RGB na ihe mmetụta mmegharị)
♦ Ambient Light na RGB Agba Sensing na UV na IR igbochi nzacha
♦ Mmetụta dị elu - Kwesịrị ekwesị maka ịrụ ọrụ n'azụ iko gbara ọchịchịrị
♦ Mmetụta ịdị nso na ọjụjụ ọkụ Ambient
♦ Mgbagwoju anya mmegharị ahụ - MP34DT06JTR (igwe okwu dijitalụ)
♦ AOP = 122.5 dbSPL
♦ 64 dB mgbama-na-mkpọtụ
♦ Omnidirectional uche
♦ -26 dBFS ± 3 dB uche - MP2322 DC-DC
♦ Na-ahazi ntinye voltage si ruo 21V nwere opekempe nke 65% arụmọrụ @ ibu kacha nta
♦ Karịrị 85% arụmọrụ @12V
The Board
Dịka bọọdụ ụdị Nano niile, Nano 33 BLE Sense Rev2 enweghị chaja batrị mana enwere ike ịkwado ya site na USB ma ọ bụ nkụnye eji isi mee.
IHEArduino Nano 33 BLE Sense Rev2 na-akwado naanị 3.3VI / Os ma ọ bụ Ọ BỤGHỊ 5V na-anabata ya, biko jide n'aka na ị naghị ejikọta akara 5V na bọọdụ a ma ọ bụ na ọ ga-emebi. Ọzọkwa, n'adịghị ka bọọdụ Arduino Nano na-akwado ọrụ 5V, pin 5V anaghị enye vol.tage mana ejikọrọ ya, site na jumper, na ntinye ike USB.
1.1 Ogo
1.1.1 Ọnọdụ ọrụ akwadoro
1.2 Ike oriri
Arụ ọrụ gafereview
2.1 Board Topology
2.2 processor
Isi ihe nhazi bụ Arm® Cortex®-M4F na-agba ọsọ ruo 64MHz. Ọtụtụ n'ime ntụtụ ya jikọtara na nkụnye eji isi mee n'èzí, mana ụfọdụ ka edobere maka nkwurịta okwu n'ime ya na modul ikuku yana n'ime ime I2C peripherals (IMU na Crypto).
IHE: N'adịghị ka bọọdụ Arduino Nano ndị ọzọ, atụdo A4 na A5 nwere ndọghachi azụ na ndabara nke a ga-eji dị ka ụgbọ ala I2C, yabụ akwadoghị iji dị ka ntinye analog.
2.3 IMU
Arduino Nano 33 BLE Sense Rev2 na-enye ike IMU na 9-axis, site na ngwakọta nke BMI270 na BMM150 ICs. BMI270 na-agụnye ma gyroscope atọ axis yana accelerometer atọ axis, ebe BMM150 nwere ike ịhụ ọdịiche magnetik n'akụkụ atọ niile. Enwere ike iji ozi enwetara maka tụọ paramita mmegharị ahụ yana maka mmụta igwe.
2.4 LPS22HB (U9) Barometer na ihe mmetụta okpomọkụ
Ihe mmetụta nrụgide LPS22HB IC (U9) gụnyere ma ihe mmetụta nrụgide zuru oke nke piezoresistive yana ihe mmetụta okpomọkụ etinyere na obere mgbawa. Ihe mmetụta nrụgide (U9) na-ejikọta isi microcontroller (U1) site na interface I2C. Ihe nhụta ahụ mejupụtara akpụkpọ anụ micromachined kwụsịtụrụ maka ịlele nrụgide zuru oke, ma gụnye akwa Wheatstone n'ime maka ịlele ihe ndị ahụ piezoresistive. A na-akwụ ụgwọ mmekpa ahụ okpomọkụ site na ihe mmetụta okpomọkụ gụnyere na mgbawa. Nrụgide zuru oke nwere ike ịdị site na 260 ruo 1260 hPa. Enwere ike ịmegharị data nrụgide site na I2C ruo 24bits, ebe enwere ike nyochaa data okpomọkụ ruo 16-bits. Ọbá akwụkwọ Arduino_LPS22HB na-enye njikere iji mmejuputa usoro I2C na mgbawa a.
2.5 HS3003 (U8) iru mmiri na ihe mmetụta okpomọkụ
HS3003 (U8) bụ ihe mmetụta MEMS, emebere iji nye ọgụgụ ziri ezi nke iru mmiri na ọnọdụ okpomọkụ na obere ngwugwu. A na-eme nkwụghachi okpomọkụ na nhazigharị na mgbawa, na-achọghị mpụga
sekit. HS3003 nwere ike tụọ iru iru mmiri site na 0% ruo 100% RH na oge nzaghachi ngwa ngwa (n'okpuru 4 sekọnd). Ihe mmetụta okpomọkụ agbakwunyere na mgbawa (eji ya maka nkwụghachi ụgwọ) nwere ezi ọnọdụ okpomọkụ nke ±0.1°C. U8 na-ekwurịta okwu site na isi microcontroller site na ụgbọ ala I2C.
sekit. HS3003 nwere ike tụọ iru iru mmiri site na 0% ruo 100% RH na oge nzaghachi ngwa ngwa (n'okpuru 4 sekọnd). Ihe mmetụta okpomọkụ agbakwunyere na mgbawa (eji ya maka nkwụghachi ụgwọ) nwere ezi ọnọdụ okpomọkụ nke ±0.1°C. U8 na-ekwurịta okwu site na isi microcontroller site na ụgbọ ala I2C.
2.5.1 Nchọpụta mmegharị
Nchọpụta mmegharị ahụ na-eji photodiodes anọ ntụzịaka iji chọpụta ike IR egosipụtara (nke sitere na ikanam agbakwunyere) iji gbanwee ozi mmegharị ahụ (dịka ọsọ, ntụzịaka na anya) gaa na ozi dijitalụ. Ihe owuwu nke injin mmegharị ahụ na-egosipụta nkwalite akpaka (dabere na nsonaazụ injin nso), mwepu ọkụ ambient, kagbuo okwu mkparịta ụka, ndị ntụgharị data 8-bit abụọ, igbu oge ngbanwe ngbanwe, 32-dataset FIFO, na nkwụsịtụ nzikọrịta ozi I2C. Injin mmegharị ahụ na-anabata ọtụtụ ihe nlegharị anya ngwaọrụ mkpanaaka chọrọ: mmegharị ahụ dị mfe elu-ala-aka nri-ekpe ka enwere ike ịghọta nke ọma. A na-ebelata oriri ike na mkpọtụ site na oge mgbanwe IR LED.
2.5.2 Nchọpụta nso
Njirimara nchọpụta nso nso na-enye nha anya (dịka ọmụmaatụ ihuenyo ngwaọrụ mkpanaka na ntị onye ọrụ) site na nchọpụta photodiode nke ike IR na-egosipụta (sitere na LED agbakwunyere). Chọpụta/mwepu ihe omume na-akwụsị, ma na-eme mgbe ọ bụla nsonaazụ nso gafere ntọala elu na/ma ọ bụ ala. Ihe njin dị nso na-egosi ndezigharị ngbanwe iji kwụọ ụgwọ nkwụghachi sistemu nke nhụsianya ike IR na-achọghị na-apụta na ihe mmetụta. A na-edozi ike IR LED n'ime ụlọ mmepụta ihe iji kpochapụ mkpa maka nhazi ngwa ngwa n'ihi mgbanwe dị iche iche. A na-emeziwanye nsonaazụ nso nso site na mwepu ọkụ ambient na-akpaghị aka.
2.5.3 Agba na nchọpụta ALS
Njirimara nchọpụta Agba na ALS na-enye data ike ọkụ na-acha uhie uhie, akwụkwọ ndụ akwụkwọ ndụ, acha anụnụ anụnụ na doro anya. Nke ọ bụla n'ime ọwa R, G, B, C nwere ihe nzacha mgbochi UV na IR yana ihe ntụgharị data raara onwe ya nye na-ewepụta data 16-bit n'otu oge. Ihe owuwu a na-enye ohere ka ngwa tụọ ọkụ ambient na agba mmetụta nke na-enyere ngwaọrụ aka ịgbakọ okpomoku agba yana njikwa ìhè azụ.
Igwe igwe dijitalụ 2.6
MP34DT06JTR bụ kọmpat ultra-compact, ike dị ala, omnidirectional, igwe okwu MEMS dijitalụ wuru yana ihe nhụta ike yana interface IC.
A na-arụpụta ihe na-ahụ ihe, nke nwere ike ịchọpụta ebili mmiri dị egwu, site na iji usoro micromachining silicon pụrụ iche a raara nye iji mepụta sensọ ọdịyo.
A na-arụpụta ihe na-ahụ ihe, nke nwere ike ịchọpụta ebili mmiri dị egwu, site na iji usoro micromachining silicon pụrụ iche a raara nye iji mepụta sensọ ọdịyo.
2.7 Osisi Ike
Enwere ike ịgbanye osisi ahụ site na eriri USB, VIN ma ọ bụ VUSB ntụtụ na nkụnye eji isi mee.
IHE: Ebe ọ bụ na VUSB na-enye VIN nri site na Schottky diode na onye na-ahụ maka DC-DC akọwapụtara obere ntinye vol.tage bụ 4.5V kacha nta ọkọnọ voltage si na USB ga-abawanye na voltage na nso n'etiti 4.8V ka 4.96V dabere na ugbu a na-adọta.
Ọrụ Board
3.1 Mmalite – IDE
Ọ bụrụ na ịchọrọ ịme mmemme Arduino Nano 33 BLE Sense Rev2 mgbe ị na-anọghị n'ịntanetị, ịkwesịrị ịwụnye Arduino Desktop IDE [1] Iji jikọọ Arduino Nano 33 BLE Sense Rev2 na kọmputa gị, ị ga-achọ eriri USB Micro-B. Nke a na-enyekwa ike na osisi ahụ, dị ka LED gosipụtara.
3.2 Mmalite – Arduino Web Onye nchịkọta akụkọ
Bọdụ Arduino niile, gụnyere nke a, na-arụ ọrụ nke ọma na Arduino Web Editor, site na ịwụnye ngwa mgbakwunye dị mfe.
Arduino Web A na-akwado onye nchịkọta akụkọ n'ịntanetị, ya mere ọ ga-adị ọhụrụ mgbe niile site na njirimara na nkwado maka bọọdụ niile. Soro ka ịmalite itinye koodu na ihe nchọgharị ahụ wee bulite ihe osise gị na bọọdụ gị.
Arduino Web A na-akwado onye nchịkọta akụkọ n'ịntanetị, ya mere ọ ga-adị ọhụrụ mgbe niile site na njirimara na nkwado maka bọọdụ niile. Soro ka ịmalite itinye koodu na ihe nchọgharị ahụ wee bulite ihe osise gị na bọọdụ gị.
3.3 Mmalite – Arduino IoT igwe ojii
A na-akwado ngwaahịa Arduino IoT niile na Arduino IoT Cloud nke na-enye gị ohere ịbanye, eserese na nyochaa data sensọ, kpalite ihe omume, wee rụzie ụlọ ma ọ bụ azụmahịa gị.
A na-akwado ngwaahịa Arduino IoT niile na Arduino IoT Cloud nke na-enye gị ohere ịbanye, eserese na nyochaa data sensọ, kpalite ihe omume, wee rụzie ụlọ ma ọ bụ azụmahịa gị.
3.4 Sampna Sketches
Sample sketị maka Arduino Nano 33 BLE Sense Rev2 nwere ike ịhụ na "Ex".amples” menu na Arduino IDE ma ọ bụ na ngalaba “Akwụkwọ” nke Arduino Pro websaịtị.
Sample sketị maka Arduino Nano 33 BLE Sense Rev2 nwere ike ịhụ na "Ex".amples” menu na Arduino IDE ma ọ bụ na ngalaba “Akwụkwọ” nke Arduino Pro websaịtị.
3.5 Ngwa ntanetị
Ugbu a na ị gafere isi ihe ị nwere ike ime na bọọdụ ị nwere ike ịchọpụta ohere na-adịghị agwụ agwụ ọ na-enye site na ịlele ọrụ na-akpali akpali na ProjectHub, Arduino Library Reference na ụlọ ahịa dị n'ahịrị ebe ị ga-enwe ike ịkwado bọọdụ gị na sensọ, actuators na ndị ọzọ.
Ugbu a na ị gafere isi ihe ị nwere ike ime na bọọdụ ị nwere ike ịchọpụta ohere na-adịghị agwụ agwụ ọ na-enye site na ịlele ọrụ na-akpali akpali na ProjectHub, Arduino Library Reference na ụlọ ahịa dị n'ahịrị ebe ị ga-enwe ike ịkwado bọọdụ gị na sensọ, actuators na ndị ọzọ.
3.6 Board Iweghachite
Bọdụ Arduino niile nwere bootloader arụnyere n'ime ya nke na-enye ohere ịmegharị bọọdụ ahụ site na USB. Ọ bụrụ na sketch kpuchiri ihe nrụpụta na bọọdụ ahụ enweghị ike iru ọzọ site na USB, ọ ga-ekwe omume ịbanye ọnọdụ bootloader site na ịpị bọtịnụ nrụpụta ugboro abụọ ozugbo emechara.
Bọdụ Arduino niile nwere bootloader arụnyere n'ime ya nke na-enye ohere ịmegharị bọọdụ ahụ site na USB. Ọ bụrụ na sketch kpuchiri ihe nrụpụta na bọọdụ ahụ enweghị ike iru ọzọ site na USB, ọ ga-ekwe omume ịbanye ọnọdụ bootloader site na ịpị bọtịnụ nrụpụta ugboro abụọ ozugbo emechara.
Pinouts njikọ
4.1 USB
4.2 nkụnye eji isi mee
Bọdụ ahụ na-ekpughe njikọ njikọ pin 15 abụọ nke enwere ike ijikọ nkụnye ntụtụ ma ọ bụ were ya na-ere ya site na vias castellated.
4.3 Nwepu
N'akụkụ ala nke osisi ahụ, n'okpuru modul nkwurịta okwu, a na-ahazi akara ngosi debug dị ka 3 × 2 test pads na 100 mil pitch na pin 4 wepụ. A na-egosi pin 1 na eserese 3 - Ọnọdụ njikọ
Ozi igwe
5.1 Ngosipụta bọọdụ na oghere nrịgo
Ngwakọta bọọdụ ahụ na-agwakọta n'etiti metric na imperial. A na-eji ihe ndị eze ukwu na-edobe grid 100 mil pitch n'etiti ahịrị pin ka ha kwekọọ na bọọdụ achịcha ebe ogologo bọọdụ bụ Metric.
Asambodo
6.1 Nkwupụta nke Nkwekọrịta CE DoC (EU)
Anyị na-ekwupụta n'okpuru ọrụ anyị naanị na ngwaahịa ndị dị n'elu kwekọrọ na ihe ndị dị mkpa nke ntuziaka EU na-esote ya mere tozuru oke maka mmegharị n'efu n'ime ahịa nke nwere European Union (EU) na European Economic Area (EEA).
6.2 Nkwuwapụta Nkwekọrịta na EU RoHS & REACH 211 01/19/2021
bọọdụ Arduino kwekọrọ na RoHS 2 Directive 2011/65/EU nke European nzuko omeiwu na RoHS 3 Directive 2015/863/EU nke Council of 4 June 2015 na mmachi nke ojiji nke ụfọdụ ize ndụ ihe na ngwa eletriki na eletrọnịkị.
Exemptions : Enweghị mpụ a na-azọrọ.
Boards Arduino na-akwado nke ọma na ihe ndị metụtara European Union Regulation (EC) 1907/2006 gbasara ndebanye aha, nyocha, ikike na mmachi nke kemịkalụ (REACH). Anyị na-ekwupụta enweghị nke SVHC (https://echa.europa.eu/)web/ guest/candidate-list-table), Ndekọ Candidate nke ihe dị oke mkpa maka ikike nke ECHA wepụtara ugbu a, dị na ngwaahịa niile (yana ngwugwu) n'ọnụọgụ mkpokọta na ntinye nha ma ọ bụ karịa 0.1%. Dị ka ihe ọmụma anyị si mara, anyị na-ekwupụtakwa na ngwaahịa anyị enweghị nke ọ bụla n'ime ihe ndị e depụtara na "Ndepụta ikike" (Annex XIV nke ụkpụrụ REACH) na ihe ndị dị oke nchegbu (SVHC) na oke ọ bụla dị mkpa dị ka akọwapụtara. site na Mgbakwunye XVII nke ndepụta Candidate bipụtara EHA (European Chemical Agency) 1907/2006/EC.
6.3 Nkwuwapụta mineral na esemokwu
Dị ka onye zuru ụwa ọnụ na-eweta ngwá electronic na eletriki eletrik, Arduino maara ọrụ anyị na-ahụ maka iwu na ụkpụrụ gbasara Conflict Minerals, kpọmkwem Dodd-Frank Wall Street Reform and Consumer Protection Act, Nkebi 1502. Arduino anaghị ebute ma ọ bụ dozie esemokwu ozugbo. mineral dị ka Tin, Tantalum, Tungsten, ma ọ bụ ọla edo. Mineral esemokwu dị na ngwaahịa anyị n'ụdị solder, ma ọ bụ dị ka akụkụ na alloys metal. Dịka akụkụ nke mbọ anyị kwesịrị ekwesị Arduino akpọtụrụla ndị na-ebubata akụrụngwa n'ime ụdọ ọkọnọ anyị iji chọpụta na ha nọgidere na-agbaso ụkpụrụ ahụ. Dabere na ozi enwetara ugbu a, anyị na-ekwupụta na ngwaahịa anyị nwere mineral na-akpata esemokwu sitere na mpaghara enweghị esemokwu.
FCC ịkpachara anya
Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ọrụ ahụ.
Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.
Nkwupụta Mkpughe Radiation FCC RF:
- Agaghị ejikọta ihe nnyefe a ma ọ bụ na-arụ ọrụ na njikọ antenna ma ọ bụ nnyefe ọ bụla ọzọ.
- Ngwa a na-akwado oke mkpughe radieshon RF ewepụtara maka gburugburu enweghị njikwa.
- Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na anya kacha nta 20cm n'etiti radiator & ahụ gị.
Igbo: Akwụkwọ ntuziaka onye ọrụ maka ngwa redio enweghị ikike ga-enwe ọkwa ndị a ma ọ bụ nha nhata n'ebe pụtara ìhè n'ime akwụkwọ ntuziaka onye ọrụ ma ọ bụ ọzọ na ngwaọrụ ma ọ bụ ha abụọ. Ngwaọrụ a na-akwado ụkpụrụ (s) RSS enweghị ikike ụlọ ọrụ Canada. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla, gụnyere nnyonye anya nwere ike bute ọrụ ngwaọrụ ahụ achọghị.
Ịdọ aka ná ntị IC SAR:
Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na anya kacha nta 20 cm n'etiti radiator na ahụ gị.
Ihe dị mkpa: Ọnọdụ okpomọkụ nke EUT enweghị ike ịgafe 85 ℃ ma ghara ịdị ala karịa -40 ℃.
Site na nke a, Arduino Srl na-ekwupụta na ngwaahịa a kwekọrọ na ihe ndị dị mkpa chọrọ yana ndokwa ndị ọzọ dị mkpa nke Ntuziaka 2014/53/EU. Ekwenyere ka ejiri ngwaahịa a na mba ndị otu EU niile.
Site na nke a, Arduino Srl na-ekwupụta na ngwaahịa a kwekọrọ na ihe ndị dị mkpa chọrọ yana ndokwa ndị ọzọ dị mkpa nke Ntuziaka 2014/53/EU. Ekwenyere ka ejiri ngwaahịa a na mba ndị otu EU niile.
Ozi ụlọ ọrụ
Akwụkwọ ntụaka
https://www.arduino.cc/en/software
https://create.arduino.cc/editor
https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduino-web-editor 4b3e4a
https://create.arduino.cc/editor
https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduino-web-editor 4b3e4a
Akụkọ ngbanwe
Arduino® Nano 33 BLE Sense Rev2
Emegharịrị: 01/08/2023
Akwụkwọ / akụrụngwa
 |
ARDUINO ABX00069 Nano BLE Sense Rev2 ARM Cortex-M4 Board [pdf] Akwụkwọ ntuziaka onye ọrụ ABX00069, ABX00070, Nano BLE Sense Rev2 ARM Cortex-M4 Board, ABX00069 Nano BLE Sense Rev2 ARM Cortex-M4 Board |