Manyèl Itilizatè Ekspozisyon Dijital Tablodbò TINKER ELECTRONIC V2

DIMANSYON

• 10” DASH
  
  
• 10” DASH
  
  
• 7” DASH
  
  
• 7” DASH
  
  
• 5"  DASH
  
  
• 5"  DASH
  

ENFÒMASYON SOU FIL

PIN	FONKSYON	KOULÈ	NÒT
1	5V	*	5v Reference
2	RESISTANCE INPUT 1	*
3	RESISTANCE INPUT 2	*
4	ANTRE ANALOG 5	*	5v Max
5	ANTRE ANALOG 4	*	5v Max
6	ANTRE ANALOG 3	*	5v Max
7	ANTRE ANALOG 2	*	5v Max
8	ANTRE ANALOG 1	*	5v Max
9	KA H	JÒN
10	KAPAB L	BLAN
11	TÈ	*
12	SWITCH 5 OUTPUT	*	SWITCHED GROUND
13	SWITCH 4 OUTPUT	*	SWITCHED GROUND
14	SWITCH 3 OUTPUT	*	SWITCHED GROUND
15	SWITCH 2 OUTPUT	*	SWITCHED GROUND
16	SWITCH 1 OUTPUT	*	SWITCHED GROUND
17	N/C	N/C
18	TÈ	*
19	TÈ	NWA
20	SWITCHED 12V	WOUJ

• Resistance pins to go to sending unit and configured within settings.
• Analog sensors powered with 5v wire and grounded with open ground pins. Configured via analog settings.
• CAN wires depending on ECU will have to be pinned into the ECU connector.
• PA FÈ EXCEED 5V ON THE ANALOG INPUTS.
• PA FÈ CONNECT 12V TO 5V WIRE OR CAN LINES.
• * = Fil ki soti nan men itilizatè final la.
• If driving relays with outputs, they cannot see 12v on the coil prior to dash switched 12v.

REMAK: Looking into wire end of connector

PLAN PRENSIPAL YO

ALL 4 OF THE MAIN PAGES CONTAIN 3 OR 4 BUTTONS AND EACH REDIRECT TO ANOTHER PAGE.

1. Bouton 1 an ap mennen ou nan paj switch yo.
2. Bouton 2 a ap mennen ou nan paj done pwolonje yo.
3. Bouton 3 a ap mennen ou nan paj EGT ki dedye a.
4. Bouton nimewo 4 la ap mennen ou nan tout diferan paramèt yo.
5. Ou ka chwazi nenpòt paramèt pou chanje li.

EXTENDED DATA PAGES

SWITCHES PAJ

EGT PAGE

PARÈJ PRINCIPAL

1. Kurseur klète.
2. Speed source to choose between ECU driven or GPS (if equipped). This uses speed from ecu if ecu source is selected.
3. Selektè Layout.
4. Bouton pou mennen ou nan paramèt switch la.
5. Bouton pou mennen ou nan diferan paramèt antre yo.
6. Bouton pou mennen ou nan Anviwònman GPS yo.
7. Bouton Anrejistre pou anrejistre tout chanjman yo pou yo ka itilize lè w ap demaraj.
8. Navigate through setting pages.
9. Bouton pou mennen ou nan paj paramèt limyè chanjman vitès la.
10. Button to take you to the layout designer to customize the 5th layout.
11. Button used to update the dash when connected to a PC.
12. Bouton pou retabli paramèt tablodbò a. Si ou kenbe l peze, kontè a ap kòmanse sou ekran an epi si ou lage l apre 5 segonn, yon retablisman ap kòmanse.

SWITCH Anviwònman

1. Chak bouton sa yo pèmèt ou chanje non switch ki parèt sou paj switch la.
2. Chanjman pou pèmèt ou chwazi si ou vle pwodiksyon an aktif/dezaktive manyèlman oubyen lye ak yon paramèt ak yon règ.
3. Deroule pou kite ou chwazi yon paramèt pou lye rezilta a avèk.
4. Desann pou chwazi agiman an.
5. Mete valè a pou agiman an.
6. Setting to choose how you want the automatic on/off act. Setting the hysteresis adds a gap between the on/off point.
7. Save switch settings.
   • Note the switches on the switch page will override the logic.

Anviwònman Antre

1. Button to take you to the sensor calculator.
2. Name column for each analog input.
   Selecting one of the name boxes will take you to the character entry to name that input (3 characters).
3. Ov value column for each input.
4. Kolòn valè 5v pou chak antre.
5. Scrolls through the input settings pages.
6. Commit the entered values.
7. Allow input 4 and 5 to be used as turn signals inputs. See reference schematic.

• Input settings button loads to analog inputs.
• Chak kare se yon bouton ki pral mennen ou nan yon ekran antre swa pou nimewo oswa tèks.
• Kalkilatris detèktè a ka itilize pou detèktè .5v-4.5v.
• Sensor calculator requires you to enter the .5v value and the 4.5v value into the light gray boxes.
• Calculate button will calculate the 0v and 5v values.
• Voye ap voye valè kalkile yo nan antre analòg ki chwazi a sou paj antre analòg la.

1. Characters to be used in each position of the 3 character input name.
2. Arrows to increment letter/number by 1.
3. Slider to rapidly scroll through available values.
4. Clear all will set all positions back to “A”.
5. Cancel will return to input settings committing no name changes.
6. Save button commits the naming.

• Chanjman non yo antre an vigè sou tout paj prensipal yo ansanm ak paj limit yo. Pa egzanpample if AS1 (analog sensor 1) name is changed to “OIL” it will appear as “OIL” everywhere used.

1. Select to enter values in front of decimal point.
2. Select to enter values behind decimal point.

• Tout bouton pou antre nimewo yo ap mennen ou nan paj antre valè a.
• CL ap mete valè a tounen sou 0.00.
• +/- ap chanje valè a soti nan pozitif pou rive nan negatif.
• Cancel will not commit values and return to page where the value was selected.
• Save will commit value and return to the page where the value was selected.

• Like the analog input page the resistance inputs are also nameable.
• Antre yo konfigire selon inite ki voye a ak valè li yo.
• Pou egzanpample a 10-95Ω fuel sending unit will be configured as:
  • MIN OHM = 10
  • MAX OHM = 95
  • MIN VAL = 0
  • MAX VAL = 100
• This can also be configured in other manners to work with various sensors and sending units.
• You can choose the preset checkbox to select from supported sending units
  
• The Custom Input page is strictly to name the custom ECU inputs that are coming over from the ECU.
• Pou egzanpample if custom input 1 on the ecu is setup for fuel pressure you can rename that value on screen to “FPR” or something of the like.

KONFIG PARAMÈT

1. Deroule pou chwazi ki paramèt ki pral parèt nan pozisyon ou chwazi a.
2. Enable/Disable the limit warning for the selected parameter. When on it will change parameter to red when rules are satisfied.
3. Argument for the limit rule.
4. Valè pou règ limit la.
5. Komèt chanjman paramèt yo.

• Exampki montre paramèt antre analòg deklanche yo.

PARAMÈT GPS

1. Anviwònman vèsyon GPS la.
2. Odometer enable for GPS 0. Enabling this will add odometer value to each default layout.
3. Inite vitès ak distans.
4. Set Odometer value. You will set this to set odometer and it will continue counting from that point as the dash is used. You can use this to correct or set miles at any time.
5. Save GPS settings.
6. The speed on main layouts will read “404” as it is searching for satellites.

PARAMÈT LIMYÈ CHANJMAN

1. Mete koulè chak LED endividyèlman.
2. RPM setting to activate shift light.
3. Entèval pwogresif la ap fikse espas RPM ki genyen ant chak LED lè stil la pwogresif.
4. Anviwònman klète LED la.
5. Color Preset. This will change all led colors to the preset color.
6. Opsyon estatik oswa pwogresif. Estatik la aktive tout LED yo an menm tan pandan ke pwogresif la kòmanse yon bale LED nan yon valè ki pi ba selon entèval la epi li kontinye jiskaske li limen nèt epi finalman flache.
7. Sa ap aktive yon avètisman LED lè nenpòt nan paramèt limit yo deklanche.
8. Save shift light settings.

LAYOUT DESIGNER

• The 5th layout is customized via the layout designer.
• The 5th layout uses a background named “BACKGROUND.jpg” at the root of the SD card.
• Size for background is 800×480 for the 5” / 7” and the 10” is 1024×600.
• The names are generic on this list as once in the positioning page you can choose the  parameter for that position

1. Button that will take you to the placement screen provided the checkbox for the parameter is checked.
2. Check box to enable/disable parameter.
3. Save configured layout.
4. Fine adjustment for the position of the parameter or button.
5. Example of the parameter based on all of the current setting. This can also be moved by dragging it with a finger.
6. Parameter font size.
7. Parameter font color.
8. Reset parameter to default location/font/color.
9. Parameter config to set value, limit, etc.
10. Save parameter information for custom layout.

EKRAN BÒT

• Custom boot images can be used. The SD card needs to have an image called “BOOT.jpg” at the root of the SD card and that will display on startup.
• Size for boot image is 800×480 for the 5” / 7” and the 10” is 1024×600.

MIZAJOU DASH LA

When upgrading from 1.55 or prior it is easiest to use the reset button on page 2 of the settings after both sections are complete. This will give clean slate for new features.

Interface Update

1. The interface update requires a Micro SD card less than 32gb and formatted as FAT32
2. Telechaje dosye zip aktyalizasyon ki apwopriye a file from the repository update section to an accessible location on your windows PC.
   Extract contents of the zip file. Telechaje LINK. There is also a link posted on the facebook page.
3. Kat SD a ta dwe vid epi li ta dwe kopye .tft ki kòrèk la. file nan kat SD ki nan rasin kat SD a. La file non an fini ak gwosè tire a (_5 pou 5", _7 pou 7", _10 pou 10").
4. With the dash off insert the SD card in the SD card slot at the top of the dash.
5. Power the dash on and the screen should go white and update the interface.
6. Once complete turn off the dash and remove the SD card.
7. Power the dash back on and check for the new UI number on page 2 of the settings indicating the interface was updated.
   Example of FW and UI numbers on next page.

Mizajou Firmware

1. Download the tools from the tools section of the repository. Extract the contents to your PC.
2. Download the update zip file from the repository to an accessible location on your windows PC. Extract contents of the zip file.
   (Sa yo files will already exist if you did the interface update). Telechaje LINK. There is also a link posted on the facebook page.
3. Lanse teensy.exe from the tools provided
   
4. Once open you can click file, open, and find the hex file provided in the email that was extracted in step 2. You do not have to worry about pressing a button like stated as long as automatic mode is on.
   
5. Once the update is selected and open you can plug a micro USB data cable from windows PC to the dash. You can also verify the tool is in auto mode by making sure the auto button is green. If it is not, you can click it and it will go green as shown below.
   
6. With the dash connected to the PC and the update loaded into the tool you can power on the dash.
7. Once the dash is on go to settings, hit the arrow for page 2, and hit the update button.
   
8. At this point if you are watching the PC you will see the update is being sent to the dash and once the update is complete the shift light will sweep. You can also go to page 1 of settings and back to page 2 and the FW number will be updated with the new version.
   
9. At this point the dash can be powered off, you can disconnect all cables, and the update is complete.

FILAJ EXAMPLES

Switch Ouput Wiring Example

Fuel Gauge Wiring Example

Turn Signal Relay Example

Using a pair of relays will let the 12v car turn circuits switch a 5v circuit that the dash can handle.

Dokiman / Resous

TINKER ELECTRONIC V2 Dash Digital Dash Display [pdfManyèl Itilizatè V2, V2 Dash Digital Dash Display, V2 Dash, Digital Dash Display, Dash Display, Display

Referans

• Manyèl itilizatè