Leabhar-làimhe Cleachdaiche Taisbeanaidh Deas-bhòrd Didseatach TINKER ELECTRONIC V2 Dash

DOMHNALLACH

• 10” DASH
  
  
• 10” DASH
  
  
• 7” DASH
  
  
• 7” DASH
  
  
• 5”  DASH
  
  
• 5”  DASH
  

FIOSRACHADH SLÀINTE

PIN	FEUCHADH	COLOR	NOTAICHEAN
1	5V	*	5v Reference
2	RESISTANCE INPUT 1	*
3	RESISTANCE INPUT 2	*
4	IONAD ANALOG 5	*	5v Max
5	IONAD ANALOG 4	*	5v Max
6	IONAD ANALOG 3	*	5v Max
7	IONAD ANALOG 2	*	5v Max
8	IONAD ANALOG 1	*	5v Max
9	CAN H.	BUIDHE
10	CAN L.	GEAL
11	GRÀTHACH	*
12	SWITCH 5 OUTPUT	*	SWITCHED GROUND
13	SWITCH 4 OUTPUT	*	SWITCHED GROUND
14	SWITCH 3 OUTPUT	*	SWITCHED GROUND
15	SWITCH 2 OUTPUT	*	SWITCHED GROUND
16	SWITCH 1 OUTPUT	*	SWITCHED GROUND
17	N/C	N/C
18	GRÀTHACH	*
19	GRÀTHACH	DUBH
20	SWITCHED 12V	DEARG

• Resistance pins to go to sending unit and configured within settings.
• Analog sensors powered with 5v wire and grounded with open ground pins. Configured via analog settings.
• CAN wires depending on ECU will have to be pinned into the ECU connector.
• NA DÈANAMH EXCEED 5V ON THE ANALOG INPUTS.
• NA DÈANAMH CONNECT 12V TO 5V WIRE OR CAN LINES.
• * = Uèir air a thoirt seachad leis an neach-cleachdaidh deireannach.
• If driving relays with outputs, they cannot see 12v on the coil prior to dash switched 12v.

NOTA: Looking into wire end of connector

PRÌOMH CHRUINN-SGRÌOBHAIDHEAN

ALL 4 OF THE MAIN PAGES CONTAIN 3 OR 4 BUTTONS AND EACH REDIRECT TO ANOTHER PAGE.

1. Bheir putan 1 thu gu duilleag nan suidsichean.
2. Bheir putan 2 thu gu na duilleagan dàta leudaichte.
3. Bheir putan 3 thu chun duilleag EGT sònraichte.
4. Bheir putan 4 thu gu na diofar roghainnean uile.
5. Faodaidh tu paramadair sam bith a thaghadh gus atharrachadh.

EXTENDED DATA PAGES

DUILLEAG SWITCHES

EGT PAGE

PRÌOMH SETTINGS

1. Sleamhnag soilleireachd.
2. Speed source to choose between ECU driven or GPS (if equipped). This uses speed from ecu if ecu source is selected.
3. Taghadair cruth.
4. Putan gus do thoirt gu roghainnean an suidse.
5. Putan gus do thoirt gu na diofar roghainnean cuir-a-steach.
6. Putan gus do thoirt gu Roghainnean GPS.
7. Putan Sàbhail gus na h-atharrachaidhean uile a dhearbhadh airson an cleachdadh aig àm tòiseachaidh.
8. Navigate through setting pages.
9. Putan gus do thoirt gu duilleag roghainnean an t-solais gluasaid.
10. Button to take you to the layout designer to customize the 5th layout.
11. Button used to update the dash when connected to a PC.
12. Putan gus roghainnean an deas-bhòrd ath-shuidheachadh. Ma chumas tu sìos e, tòisichidh an cunntair air an sgrion agus ma leigeas tu às e às dèidh 5 diogan, tòisichidh ath-shuidheachadh.

LAOIDHEAN SWITCH

1. Leigidh gach aon de na putanan seo leat ainm an suidse a tha air a shealltainn air duilleag an suidse atharrachadh.
2. Togalaiche air/ dheth gus leigeil leat taghadh a bheil thu airson an toradh a bhith air/ dheth le làimh no ceangailte ri paramadair agus riaghailt.
3. Clàr-taice gus leigeil leat paramadair a thaghadh gus an toradh a cheangal ris.
4. Leig sìos gus an argamaid a thaghadh.
5. Suidhich an luach airson an argamaid.
6. Setting to choose how you want the automatic on/off act. Setting the hysteresis adds a gap between the on/off point.
7. Save switch settings.
   • Note the switches on the switch page will override the logic.

SEALLACHDAN IONMHOR

1. Button to take you to the sensor calculator.
2. Name column for each analog input.
   Selecting one of the name boxes will take you to the character entry to name that input (3 characters).
3. Ov value column for each input.
4. Colbh luach 5v airson gach cuir-a-steach.
5. Scrolls through the input settings pages.
6. Commit the entered values.
7. Allow input 4 and 5 to be used as turn signals inputs. See reference schematic.

• Input settings button loads to analog inputs.
• ’S e putan a th’ anns gach bogsa a bheir thu gu scrion inntrigidh airson àireamhan no teacsa.
• Faodar àireamhair mothachaidh a chleachdadh airson mothachairean .5v-4.5v.
• Sensor calculator requires you to enter the .5v value and the 4.5v value into the light gray boxes.
• Calculate button will calculate the 0v and 5v values.
• Cuiridh Send na luachan obraichte chun an ionchur analogach taghte air duilleag an ionchur analogach.

1. Characters to be used in each position of the 3 character input name.
2. Arrows to increment letter/number by 1.
3. Slider to rapidly scroll through available values.
4. Clear all will set all positions back to “A”.
5. Cancel will return to input settings committing no name changes.
6. Save button commits the naming.

• Bidh atharrachaidhean ainm a’ tighinn gu buil air na prìomh dhuilleagan uile a bharrachd air duilleagan cuibhrichte. Mar eisimpleirample if AS1 (analog sensor 1) name is changed to “OIL” it will appear as “OIL” everywhere used.

1. Select to enter values in front of decimal point.
2. Select to enter values behind decimal point.

• Bheir na putanan cuir a-steach àireamhan uile thu chun duilleag cuir a-steach luach.
• Cuiridh CL an luach air ais gu 0.00.
• Bidh +/- ag atharrachadh an luach bho dheimhinneach gu àicheil.
• Cancel will not commit values and return to page where the value was selected.
• Save will commit value and return to the page where the value was selected.

• Like the analog input page the resistance inputs are also nameable.
• Tha na cuir-a-steach air an rèiteachadh a rèir an aonaid cur agus na luachan aige.
• Airson example a 10-95Ω fuel sending unit will be configured as:
  • MIN OHM = 10
  • MAX OHM = 95
  • MIN VAL = 0
  • MAX VAL = 100
• This can also be configured in other manners to work with various sensors and sending units.
• You can choose the preset checkbox to select from supported sending units
  
• The Custom Input page is strictly to name the custom ECU inputs that are coming over from the ECU.
• Airson example if custom input 1 on the ecu is setup for fuel pressure you can rename that value on screen to “FPR” or something of the like.

RÈITEADH PARAIMEAR

1. Cliog sìos gus taghadh dè am paramadair a thèid a shealltainn san t-suidheachadh taghte.
2. Enable/Disable the limit warning for the selected parameter. When on it will change parameter to red when rules are satisfied.
3. Argument for the limit rule.
4. Luach airson riaghailt na crìche.
5. Cuir atharrachaidhean paramadair an gnìomh.

• Exampa’ sealltainn nam paramadairean cuir-a-steach analogach a chaidh a bhrosnachadh.

Roghainnean GPS

1. Suidheachadh dreach GPS.
2. Odometer enable for GPS 0. Enabling this will add odometer value to each default layout.
3. Aonadan astair is astar.
4. Set Odometer value. You will set this to set odometer and it will continue counting from that point as the dash is used. You can use this to correct or set miles at any time.
5. Save GPS settings.
6. The speed on main layouts will read “404” as it is searching for satellites.

Roghainnean Solais Shift

1. Suidhich gach dath LED fa leth.
2. RPM setting to activate shift light.
3. Suidhichidh an eadar-ama adhartach am beàrn RPM eadar gach LED nuair a bhios an stoidhle adhartach.
4. Suidheachadh soilleireachd LED.
5. Color Preset. This will change all led colors to the preset color.
6. Roghainnean statach no adhartach. Bidh statach a’ cur nan LEDan uile an gnìomh aig an aon àm agus bidh adhartach a’ tòiseachadh sguab LED aig luach nas ìsle a rèir an eadar-ama agus ag obair a shlighe gus am bi e làn lasadh agus mu dheireadh a’ priobadh.
7. Cuiridh seo an comas LED rabhaidh nuair a thèid gin de na roghainnean crìche a bhrosnachadh.
8. Save shift light settings.

LAYOUT DESIGNER

• The 5th layout is customized via the layout designer.
• The 5th layout uses a background named “BACKGROUND.jpg” at the root of the SD card.
• Size for background is 800×480 for the 5” / 7” and the 10” is 1024×600.
• The names are generic on this list as once in the positioning page you can choose the  parameter for that position

1. Button that will take you to the placement screen provided the checkbox for the parameter is checked.
2. Check box to enable/disable parameter.
3. Save configured layout.
4. Fine adjustment for the position of the parameter or button.
5. Example of the parameter based on all of the current setting. This can also be moved by dragging it with a finger.
6. Parameter font size.
7. Parameter font color.
8. Reset parameter to default location/font/color.
9. Parameter config to set value, limit, etc.
10. Save parameter information for custom layout.

Sgrion BOOT

• Custom boot images can be used. The SD card needs to have an image called “BOOT.jpg” at the root of the SD card and that will display on startup.
• Size for boot image is 800×480 for the 5” / 7” and the 10” is 1024×600.

A’ cur ùrachadh air an deas-bhòrd

When upgrading from 1.55 or prior it is easiest to use the reset button on page 2 of the settings after both sections are complete. This will give clean slate for new features.

Interface Update

1. The interface update requires a Micro SD card less than 32gb and formatted as FAT32
2. Luchdaich a-nuas am faidhle zip ùrachaidh iomchaidh file from the repository update section to an accessible location on your windows PC.
   Extract contents of the zip file. CEANGAL DOWNLOAD. There is also a link posted on the facebook page.
3. Bu chòir don chairt SD a bhith falamh agus lethbhreac den fhaidhle .tft cheart a dhèanamh. file chun a’ chairt SD aig freumh a’ chairt SD. An file Tha an t-ainm a’ crìochnachadh le meud an sgrìob (_5 airson 5”, _7 airson 7”, _10 airson 10”).
4. With the dash off insert the SD card in the SD card slot at the top of the dash.
5. Power the dash on and the screen should go white and update the interface.
6. Once complete turn off the dash and remove the SD card.
7. Power the dash back on and check for the new UI number on page 2 of the settings indicating the interface was updated.
   Example of FW and UI numbers on next page.

Firmware ùrachadh

1. Download the tools from the tools section of the repository. Extract the contents to your PC.
2. Download the update zip file from the repository to an accessible location on your windows PC. Extract contents of the zip file.
   (Tha iad seo files will already exist if you did the interface update). CEANGAL DOWNLOAD. There is also a link posted on the facebook page.
3. Cur air bhog teensy.exe from the tools provided
   
4. Once open you can click file, open, and find the hex file provided in the email that was extracted in step 2. You do not have to worry about pressing a button like stated as long as automatic mode is on.
   
5. Once the update is selected and open you can plug a micro USB data cable from windows PC to the dash. You can also verify the tool is in auto mode by making sure the auto button is green. If it is not, you can click it and it will go green as shown below.
   
6. With the dash connected to the PC and the update loaded into the tool you can power on the dash.
7. Once the dash is on go to settings, hit the arrow for page 2, and hit the update button.
   
8. At this point if you are watching the PC you will see the update is being sent to the dash and once the update is complete the shift light will sweep. You can also go to page 1 of settings and back to page 2 and the FW number will be updated with the new version.
   
9. At this point the dash can be powered off, you can disconnect all cables, and the update is complete.

URRAMACH EXAMPLAOIDH

Switch Ouput Wiring Example

Fuel Gauge Wiring Example

Turn Signal Relay Example

Using a pair of relays will let the 12v car turn circuits switch a 5v circuit that the dash can handle.

Sgrìobhainnean/Goireasan

TINKER ELECTRONIC V2 Dash Digital Dash Display [pdfLeabhar-làimhe an neach-cleachdaidh V2, V2 Dash Digital Dash Display, V2 Dash, Digital Dash Display, Dash Display, Display

Iomraidhean

• Leabhar-làimhe cleachdaiche