Lámhleabhar Úsáideora Taispeántais Painéil Dhigitigh TINKER ELECTRONIC V2

TOISE

• 10” DASH
  
  
• 10” DASH
  
  
• 7” DASH
  
  
• 7” DASH
  
  
• 5"  DASH
  
  
• 5"  DASH
  

Sreangú EOLAS

UAP	FEIDHM	DATH	NÓTAÍ
1	5V	*	5v Reference
2	RESISTANCE INPUT 1	*
3	RESISTANCE INPUT 2	*
4	IONCHUR ANALóg 5	*	5v Max
5	IONCHUR ANALóg 4	*	5v Max
6	IONCHUR ANALóg 3	*	5v Max
7	IONCHUR ANALóg 2	*	5v Max
8	IONCHUR ANALóg 1	*	5v Max
9	IS FÉIDIR H.	BUÍ
10	FÉIDIR L.	BÁN
11	TALAMH	*
12	SWITCH 5 OUTPUT	*	SWITCHED GROUND
13	SWITCH 4 OUTPUT	*	SWITCHED GROUND
14	SWITCH 3 OUTPUT	*	SWITCHED GROUND
15	SWITCH 2 OUTPUT	*	SWITCHED GROUND
16	SWITCH 1 OUTPUT	*	SWITCHED GROUND
17	N/C	N/C
18	TALAMH	*
19	TALAMH	DUBH
20	SWITCHED 12V	DEARG

• Resistance pins to go to sending unit and configured within settings.
• Analog sensors powered with 5v wire and grounded with open ground pins. Configured via analog settings.
• CAN wires depending on ECU will have to be pinned into the ECU connector.
• NÁ EXCEED 5V ON THE ANALOG INPUTS.
• NÁ CONNECT 12V TO 5V WIRE OR CAN LINES.
• * = Sreang arna soláthar ag an úsáideoir deiridh.
• If driving relays with outputs, they cannot see 12v on the coil prior to dash switched 12v.

NÓTA: Looking into wire end of connector

PRÍOMHLEAGAN LEAGAN ISTEACH

ALL 4 OF THE MAIN PAGES CONTAIN 3 OR 4 BUTTONS AND EACH REDIRECT TO ANOTHER PAGE.

1. Tabharfaidh cnaipe 1 chuig leathanach na lasca thú.
2. Tabharfaidh cnaipe 2 chuig na leathanaigh sonraí leathnaithe thú.
3. Tabharfaidh cnaipe 3 chuig an leathanach EGT tiomnaithe thú.
4. Tabharfaidh cnaipe 4 chuig na socruithe éagsúla thú.
5. Is féidir leat aon pharaiméadar a roghnú chun é a athrú.

EXTENDED DATA PAGES

LEATHANACH SWITCHES

EGT PAGE

PRÍOMH-SHOCRUITHE

1. Sleamhnán gile.
2. Speed source to choose between ECU driven or GPS (if equipped). This uses speed from ecu if ecu source is selected.
3. Roghnóir leagan amach.
4. Cnaipe chun tú a thabhairt chuig socruithe an lasc.
5. Cnaipe chun tú a thabhairt chuig na socruithe ionchuir éagsúla.
6. Cnaipe chun tú a thabhairt chuig Socruithe GPS.
7. Cnaipe Sábháil chun na hathruithe go léir a chur i bhfeidhm lena n-úsáid ag an am tosaithe.
8. Navigate through setting pages.
9. Cnaipe chun tú a thabhairt chuig leathanach socruithe an tsolais aistrithe.
10. Button to take you to the layout designer to customize the 5th layout.
11. Button used to update the dash when connected to a PC.
12. Cnaipe chun socruithe an deais a athshocrú. Tosóidh an cuntar ar an scáileán má shealbhaítear síos é agus má scaoiltear é tar éis 5 soicind cuirfear tús le hathshocrú.

LÍONRAÍ SWITCH

1. Le gach ceann de na cnaipí seo is féidir leat ainm an lasca atá le feiceáil ar leathanach an lasca a athrú.
2. Scoránaigh Ar/As chun ligean duit a roghnú an bhfuil an t-aschur uait de láimh nó ceangailte le paraiméadar agus riail.
3. Anuas roghchlár chun ligean duit paraiméadar a roghnú chun an t-aschur a cheangal leis.
4. Titim síos chun an argóint a roghnú.
5. Socraigh an luach don argóint.
6. Setting to choose how you want the automatic on/off act. Setting the hysteresis adds a gap between the on/off point.
7. Save switch settings.
   • Note the switches on the switch page will override the logic.

SOCRUITHE IONCHUR

1. Button to take you to the sensor calculator.
2. Name column for each analog input.
   Selecting one of the name boxes will take you to the character entry to name that input (3 characters).
3. Ov value column for each input.
4. Colún luacha 5v do gach ionchur.
5. Scrolls through the input settings pages.
6. Commit the entered values.
7. Allow input 4 and 5 to be used as turn signals inputs. See reference schematic.

• Input settings button loads to analog inputs.
• Is cnaipe é gach bosca a thabharfaidh chuig scáileán iontrála thú le haghaidh uimhreacha nó téacs.
• Is féidir áireamhán braiteora a úsáid le haghaidh braiteoirí .5v-4.5v.
• Sensor calculator requires you to enter the .5v value and the 4.5v value into the light gray boxes.
• Calculate button will calculate the 0v and 5v values.
• Seolfaidh Seol na luachanna ríofa chuig an ionchur analógach roghnaithe ar an leathanach ionchuir analógach.

1. Characters to be used in each position of the 3 character input name.
2. Arrows to increment letter/number by 1.
3. Slider to rapidly scroll through available values.
4. Clear all will set all positions back to “A”.
5. Cancel will return to input settings committing no name changes.
6. Save button commits the naming.

• Cuirtear athruithe ainmneacha i bhfeidhm ar na príomhleathanaigh uile chomh maith le leathanaigh theoranta. Mar shamplaample if AS1 (analog sensor 1) name is changed to “OIL” it will appear as “OIL” everywhere used.

1. Select to enter values in front of decimal point.
2. Select to enter values behind decimal point.

• Tabharfaidh na cnaipí ionchuir uimhreacha go léir chuig an leathanach iontrála luacha thú.
• Socróidh CL an luach ar ais go 0.00.
• Athróidh +/- an luach ó dhearfach go diúltach.
• Cancel will not commit values and return to page where the value was selected.
• Save will commit value and return to the page where the value was selected.

• Like the analog input page the resistance inputs are also nameable.
• Tá na hionchuir cumraithe don aonad seolta agus a luachanna.
• Le haghaidh example a 10-95Ω fuel sending unit will be configured as:
  • MIN OHM = 10
  • MAX OHM = 95
  • MIN VAL = 0
  • MAX VAL = 100
• This can also be configured in other manners to work with various sensors and sending units.
• You can choose the preset checkbox to select from supported sending units
  
• The Custom Input page is strictly to name the custom ECU inputs that are coming over from the ECU.
• Le haghaidh example if custom input 1 on the ecu is setup for fuel pressure you can rename that value on screen to “FPR” or something of the like.

Cumraíocht Paraiméadair

1. Titim anuas chun a roghnú cén paraiméadar atá le feiceáil sa suíomh roghnaithe.
2. Enable/Disable the limit warning for the selected parameter. When on it will change parameter to red when rules are satisfied.
3. Argument for the limit rule.
4. Luach don riail teorann.
5. Athruithe paraiméadair a thiomnú.

• Example ag taispeáint na paraiméadair ionchuir analógacha spreagtha.

Socruithe GPS

1. Socrú Leagan GPS.
2. Odometer enable for GPS 0. Enabling this will add odometer value to each default layout.
3. Aonaid luais agus achair.
4. Set Odometer value. You will set this to set odometer and it will continue counting from that point as the dash is used. You can use this to correct or set miles at any time.
5. Save GPS settings.
6. The speed on main layouts will read “404” as it is searching for satellites.

Socruithe Solais Shift

1. Socraigh gach dath LED aonair.
2. RPM setting to activate shift light.
3. Socróidh eatramh forásach an bhearna RPM idir gach LED nuair a bhíonn an stíl forásach.
4. Socrú gile LED.
5. Color Preset. This will change all led colors to the preset color.
6. Roghanna statach nó forásacha. Gníomhaíonn statach na soilse LED go léir ag an am céanna agus tosaíonn forásach scuabadh LED ag luach níos ísle ag brath ar an eatramh agus oibríonn sé a bhealach go dtí go lasann sé go hiomlán agus go splancann sé sa deireadh.
7. Cumasóidh sé seo LED rabhaidh nuair a chuirtear aon cheann de na socruithe teorann i ngníomh.
8. Save shift light settings.

LAYOUT DESIGNER

• The 5th layout is customized via the layout designer.
• The 5th layout uses a background named “BACKGROUND.jpg” at the root of the SD card.
• Size for background is 800×480 for the 5” / 7” and the 10” is 1024×600.
• The names are generic on this list as once in the positioning page you can choose the  parameter for that position

1. Button that will take you to the placement screen provided the checkbox for the parameter is checked.
2. Check box to enable/disable parameter.
3. Save configured layout.
4. Fine adjustment for the position of the parameter or button.
5. Example of the parameter based on all of the current setting. This can also be moved by dragging it with a finger.
6. Parameter font size.
7. Parameter font color.
8. Reset parameter to default location/font/color.
9. Parameter config to set value, limit, etc.
10. Save parameter information for custom layout.

Scáileán tosaithe

• Custom boot images can be used. The SD card needs to have an image called “BOOT.jpg” at the root of the SD card and that will display on startup.
• Size for boot image is 800×480 for the 5” / 7” and the 10” is 1024×600.

AG NUASHONRÚ AN PHAIS

When upgrading from 1.55 or prior it is easiest to use the reset button on page 2 of the settings after both sections are complete. This will give clean slate for new features.

Interface Update

1. The interface update requires a Micro SD card less than 32gb and formatted as FAT32
2. Íoslódáil an zip nuashonraithe cuí file from the repository update section to an accessible location on your windows PC.
   Extract contents of the zip file. NASC DOWNLOAD. There is also a link posted on the facebook page.
3. Ba chóir go mbeadh an cárta SD folamh agus an comhad .tft ceart cóipeáilte aige. file chuig an gcárta SD ag fréamh an chárta SD. An file críochnaíonn an t-ainm le méid an fleasc (_5 le haghaidh 5”, _7 le haghaidh 7”, _10 le haghaidh 10”).
4. With the dash off insert the SD card in the SD card slot at the top of the dash.
5. Power the dash on and the screen should go white and update the interface.
6. Once complete turn off the dash and remove the SD card.
7. Power the dash back on and check for the new UI number on page 2 of the settings indicating the interface was updated.
   Example of FW and UI numbers on next page.

Nuashonrú Firmware

1. Download the tools from the tools section of the repository. Extract the contents to your PC.
2. Download the update zip file from the repository to an accessible location on your windows PC. Extract contents of the zip file.
   (Seo files will already exist if you did the interface update). NASC DOWNLOAD. There is also a link posted on the facebook page.
3. Seoladh teensy.exe from the tools provided
   
4. Once open you can click file, open, and find the hex file provided in the email that was extracted in step 2. You do not have to worry about pressing a button like stated as long as automatic mode is on.
   
5. Once the update is selected and open you can plug a micro USB data cable from windows PC to the dash. You can also verify the tool is in auto mode by making sure the auto button is green. If it is not, you can click it and it will go green as shown below.
   
6. With the dash connected to the PC and the update loaded into the tool you can power on the dash.
7. Once the dash is on go to settings, hit the arrow for page 2, and hit the update button.
   
8. At this point if you are watching the PC you will see the update is being sent to the dash and once the update is complete the shift light will sweep. You can also go to page 1 of settings and back to page 2 and the FW number will be updated with the new version.
   
9. At this point the dash can be powered off, you can disconnect all cables, and the update is complete.

Sreangú EXAMPLES

Switch Ouput Wiring Example

Fuel Gauge Wiring Example

Turn Signal Relay Example

Using a pair of relays will let the 12v car turn circuits switch a 5v circuit that the dash can handle.

Doiciméid / Acmhainní

TINKER ELECTRONIC V2 Dash Digital Dash Display [pdfLámhleabhar Úsáideora V2, V2 Dash Digital Dash Display, V2 Dash, Digital Dash Display, Dash Display, Display

Tagairtí

• Lámhleabhar Úsáideora