TINKER ELECTRONIC V2 Dash Digital Dash Nuni Mai Amfani

GIRMA

• 10” DASH
  
  
• 10” DASH
  
  
• 7” DASH
  
  
• 7” DASH
  
  
• 5”  DASH
  
  
• 5”  DASH
  

BAYANIN WIRING

PIN	AIKI	LAUNIYA	BAYANI
1	5V	*	5v Reference
2	RESISTANCE INPUT 1	*
3	RESISTANCE INPUT 2	*
4	ANALOG INPUT 5	*	5v Max
5	ANALOG INPUT 4	*	5v Max
6	ANALOG INPUT 3	*	5v Max
7	ANALOG INPUT 2	*	5v Max
8	ANALOG INPUT 1	*	5v Max
9	CAN H	YELU
10	IYA L	FARIYA
11	GASA	*
12	SWITCH 5 OUTPUT	*	SWITCHED GROUND
13	SWITCH 4 OUTPUT	*	SWITCHED GROUND
14	SWITCH 3 OUTPUT	*	SWITCHED GROUND
15	SWITCH 2 OUTPUT	*	SWITCHED GROUND
16	SWITCH 1 OUTPUT	*	SWITCHED GROUND
17	N/C	N/C
18	GASA	*
19	GASA	BAKI
20	SWITCHED 12V	JAN

• Resistance pins to go to sending unit and configured within settings.
• Analog sensors powered with 5v wire and grounded with open ground pins. Configured via analog settings.
• CAN wires depending on ECU will have to be pinned into the ECU connector.
• KAR KA EXCEED 5V ON THE ANALOG INPUTS.
• KAR KA CONNECT 12V TO 5V WIRE OR CAN LINES.
• * = Waya mai amfani na ƙarshe.
• If driving relays with outputs, they cannot see 12v on the coil prior to dash switched 12v.

NOTE: Looking into wire end of connector

BABBAN FARKO

ALL 4 OF THE MAIN PAGES CONTAIN 3 OR 4 BUTTONS AND EACH REDIRECT TO ANOTHER PAGE.

1. Maɓallin 1 zai kai ku zuwa shafin sauyawa.
2. Maballin 2 zai kai ku zuwa shafukan da aka fadada.
3. Maɓallin 3 zai kai ku zuwa shafin EGT da aka keɓe.
4. Button 4 zai kai ku zuwa duk saitunan daban-daban.
5. Kuna iya zaɓar kowane siga don canza shi.

EXTENDED DATA PAGES

SHAFIN MUSULUNCI

EGT PAGE

BABBAN TSARI

1. Hasken haske.
2. Speed source to choose between ECU driven or GPS (if equipped). This uses speed from ecu if ecu source is selected.
3. Mai zaɓin shimfidar wuri.
4. Maɓallin don kai ku zuwa saitunan sauya sheka.
5. Maɓallin don kai ku zuwa saitunan shigarwa daban-daban.
6. Maɓallin don kai ku zuwa Saitunan GPS.
7. Ajiye maɓallin don aiwatar da duk canje-canje da za a yi amfani da su yayin farawa.
8. Navigate through setting pages.
9. Maɓallin don kai ku zuwa shafin saitunan haske na motsi.
10. Button to take you to the layout designer to customize the 5th layout.
11. Button used to update the dash when connected to a PC.
12. Maɓalli don sake saita saitunan dash. Riƙe ƙasa zai fara counter ɗin allo kuma idan an sake shi bayan daƙiƙa 5 sake saiti zai fara.

SAUYI SETTING

1. Kowane ɗayan waɗannan maɓallan yana ba ku damar canza sunan maɓalli wanda aka nuna akan shafin sauya.
2. Kunna/kashewa don barin ku zaɓi ko kuna son abin fitarwa ya zama kunnawa/kashewa ko ɗaure da siga da ƙa'ida.
3. Sauke ƙasa don ƙyale ka zaɓi siga don ɗaure fitarwa zuwa.
4. Sauke ƙasa don zaɓar hujja.
5. Saita ƙimar hujja.
6. Setting to choose how you want the automatic on/off act. Setting the hysteresis adds a gap between the on/off point.
7. Save switch settings.
   • Note the switches on the switch page will override the logic.

SAIRIN SHIGA

1. Button to take you to the sensor calculator.
2. Name column for each analog input.
   Selecting one of the name boxes will take you to the character entry to name that input (3 characters).
3. Ov value column for each input.
4. 5v ginshiƙin ƙima na kowane shigarwa.
5. Scrolls through the input settings pages.
6. Commit the entered values.
7. Allow input 4 and 5 to be used as turn signals inputs. See reference schematic.

• Input settings button loads to analog inputs.
• Kowane akwati maɓalli ne wanda zai kai ka zuwa allon shigarwa don ko dai lambobi ko rubutu.
• Ana iya amfani da kalkuleta na firikwensin don firikwensin .5v-4.5v.
• Sensor calculator requires you to enter the .5v value and the 4.5v value into the light gray boxes.
• Calculate button will calculate the 0v and 5v values.
• Aika zai aika da ƙididdige ƙididdiga zuwa shigarwar analog ɗin da aka zaɓa akan shafin shigar da analog.

1. Characters to be used in each position of the 3 character input name.
2. Arrows to increment letter/number by 1.
3. Slider to rapidly scroll through available values.
4. Clear all will set all positions back to “A”.
5. Cancel will return to input settings committing no name changes.
6. Save button commits the naming.

• Canje-canjen suna yana aiki akan duk manyan shafuka da kuma iyakance shafuka. Don misaliample if AS1 (analog sensor 1) name is changed to “OIL” it will appear as “OIL” everywhere used.

1. Select to enter values in front of decimal point.
2. Select to enter values behind decimal point.

• Duk maɓallan shigar da lamba zasu kai ku zuwa shafin shigarwar ƙimar.
• CL zai saita darajar zuwa 0.00.
• +/- zai canza darajar daga tabbatacce zuwa mara kyau.
• Cancel will not commit values and return to page where the value was selected.
• Save will commit value and return to the page where the value was selected.

• Like the analog input page the resistance inputs are also nameable.
• An saita abubuwan shigar zuwa sashin aikawa da ƙimar sa.
• Don misaliample a 10-95Ω fuel sending unit will be configured as:
  • MIN OHM = 10
  • MAX OHM = 95
  • MIN VAL = 0
  • MAX VAL = 100
• This can also be configured in other manners to work with various sensors and sending units.
• You can choose the preset checkbox to select from supported sending units
  
• The Custom Input page is strictly to name the custom ECU inputs that are coming over from the ECU.
• Don misaliample if custom input 1 on the ecu is setup for fuel pressure you can rename that value on screen to “FPR” or something of the like.

TSARIN PARAMETER

1. Sauke ƙasa don zaɓar abin da aka nuna siga a wurin da aka zaɓa.
2. Enable/Disable the limit warning for the selected parameter. When on it will change parameter to red when rules are satisfied.
3. Argument for the limit rule.
4. Darajar ga ƙa'idar iyaka.
5. Ƙaddamar da canje-canje.

• Exampda nuna alamun shigarwar analog da aka jawo.

GASKIYAR GPS

1. Saitin Sigar GPS.
2. Odometer enable for GPS 0. Enabling this will add odometer value to each default layout.
3. Gudu da nisa raka'a.
4. Set Odometer value. You will set this to set odometer and it will continue counting from that point as the dash is used. You can use this to correct or set miles at any time.
5. Save GPS settings.
6. The speed on main layouts will read “404” as it is searching for satellites.

SHIFT KYAUTA

1. Saita kowane launi na LED.
2. RPM setting to activate shift light.
3. Tazarar ci gaba za ta saita tazarar RPM tsakanin kowace LED lokacin da salon ya ci gaba.
4. Saitin haske na LED.
5. Color Preset. This will change all led colors to the preset color.
6. Zaɓuɓɓuka masu tsayi ko ci gaba. Static yana kunna duk LEDS a lokaci ɗaya yayin da ci gaba yana fara sharewar LED a ƙaramin ƙima dangane da tazara kuma yana aiki da hanyarsa don haskaka haske kuma a ƙarshe yana walƙiya.
7. Wannan zai ba da damar LED mai faɗakarwa lokacin da aka kunna kowane saitunan iyaka.
8. Save shift light settings.

LAYOUT DESIGNER

• The 5th layout is customized via the layout designer.
• The 5th layout uses a background named “BACKGROUND.jpg” at the root of the SD card.
• Size for background is 800×480 for the 5” / 7” and the 10” is 1024×600.
• The names are generic on this list as once in the positioning page you can choose the  parameter for that position

1. Button that will take you to the placement screen provided the checkbox for the parameter is checked.
2. Check box to enable/disable parameter.
3. Save configured layout.
4. Fine adjustment for the position of the parameter or button.
5. Example of the parameter based on all of the current setting. This can also be moved by dragging it with a finger.
6. Parameter font size.
7. Parameter font color.
8. Reset parameter to default location/font/color.
9. Parameter config to set value, limit, etc.
10. Save parameter information for custom layout.

BOOT SCREEN

• Custom boot images can be used. The SD card needs to have an image called “BOOT.jpg” at the root of the SD card and that will display on startup.
• Size for boot image is 800×480 for the 5” / 7” and the 10” is 1024×600.

INGANTA DASH

When upgrading from 1.55 or prior it is easiest to use the reset button on page 2 of the settings after both sections are complete. This will give clean slate for new features.

Interface Update

1. The interface update requires a Micro SD card less than 32gb and formatted as FAT32
2. Zazzage zip ɗin da ya dace file from the repository update section to an accessible location on your windows PC.
   Extract contents of the zip file. LINK SAUKI. There is also a link posted on the facebook page.
3. Katin SD ya zama fanko kuma ya kwafi daidai .tft file zuwa katin SD a tushen katin SD. The file Sunan yana ƙare da girman dash (_5 don 5", _7 don 7", _10 don 10").
4. With the dash off insert the SD card in the SD card slot at the top of the dash.
5. Power the dash on and the screen should go white and update the interface.
6. Once complete turn off the dash and remove the SD card.
7. Power the dash back on and check for the new UI number on page 2 of the settings indicating the interface was updated.
   Example of FW and UI numbers on next page.

Sabunta Firmware

1. Download the tools from the tools section of the repository. Extract the contents to your PC.
2. Download the update zip file from the repository to an accessible location on your windows PC. Extract contents of the zip file.
   (Waɗannan files will already exist if you did the interface update). LINK SAUKI. There is also a link posted on the facebook page.
3. Kaddamar teensy.exe from the tools provided
   
4. Once open you can click file, open, and find the hex file provided in the email that was extracted in step 2. You do not have to worry about pressing a button like stated as long as automatic mode is on.
   
5. Once the update is selected and open you can plug a micro USB data cable from windows PC to the dash. You can also verify the tool is in auto mode by making sure the auto button is green. If it is not, you can click it and it will go green as shown below.
   
6. With the dash connected to the PC and the update loaded into the tool you can power on the dash.
7. Once the dash is on go to settings, hit the arrow for page 2, and hit the update button.
   
8. At this point if you are watching the PC you will see the update is being sent to the dash and once the update is complete the shift light will sweep. You can also go to page 1 of settings and back to page 2 and the FW number will be updated with the new version.
   
9. At this point the dash can be powered off, you can disconnect all cables, and the update is complete.

WIRING EXAMPLES

Switch Ouput Wiring Example

Fuel Gauge Wiring Example

Turn Signal Relay Example

Using a pair of relays will let the 12v car turn circuits switch a 5v circuit that the dash can handle.

Takardu / Albarkatu

TINKER ELECTRONIC V2 Dash Digital Dash Display [pdf] Manual mai amfani V2, V2 Dash Digital Dash Display, V2 Dash, Digital Dash Display, Dash Display, Display

Magana

• Manual mai amfani