SIGLENT SDG2000X Series Muaj nuj nqi Arbitrary Waveform Generator Tus neeg siv phau ntawv

SDG2000X Series
Function/Arbitrary
Waveform Generator
Cov neeg siv phau ntawv
UM0202X-E02G
SIGLENT TECHNOLOGIES CO..LTD

Cov ntsiab lus zais

1 SDG2000X Series Function Arbitrary Waveform Generator

2 General Safety Summary

3 Cov ntsiab lus kev nyab xeeb thiab cov cim

4 Taw qhia ntawm SDG2000X

5 Pib nrawm

6 Kev ua haujlwm pem hauv ntej

7 Examples

8 Kev daws teeb meem

9 Kev Pabcuam thiab Kev Pabcuam

10 Cov ntawv ntxiv

11 Cov ntaub ntawv / Cov ntaub ntawv

11.1 Cov ntaub ntawv

SDG2000X Series Function Arbitrary Waveform Generator

Tshaj tawm
Copyright © SIGLENT TECHNOLOGIES CO., LTD. Txhua txoj cai.
Yog tsis muaj kev tso cai, cov ntsiab lus hauv phau ntawv no tsis raug tso cai muab luam tawm, muab rho tawm lossis txhais.

General Safety Summary

Ua tib zoo nyeem cov lus ceeb toom txog kev nyab xeeb hauv qab no kom tsis txhob muaj kev raug mob ntawm tus kheej lossis kev puas tsuaj rau lub cuab yeej thiab cov khoom siv txuas nrog. Txhawm rau kom tsis txhob muaj kev phom sij, thov siv lub cuab yeej raws li tau teev tseg.
Tsuas yog cov neeg ua haujlwm tsim nyog yuav tsum tau muab cov cuab yeej no.
Tsis txhob tua hluav taws lossis qhib nplaim taws.
Siv cov kab hluav taws xob sib txuas kom zoo.
Tsuas yog siv cov kab hluav taws xob uas tau pom zoo los ntawm koj lub koom haum tswj hwm hauv cheeb tsam.
Pem Hauv Ntej Instrument.
Qhov ntsuas yog grounded los ntawm kev tiv thaiv hauv av conductor ntawm lub hwj chim kab. Txhawm rau kom tsis txhob muaj hluav taws xob poob siab, tus neeg xyuas pib hauv av yuav tsum tau txuas nrog lub ntiaj teb hauv av. Xyuas kom tseeb tias lub ntsuas yog grounded kom raug ua ntej txuas nws cov tswv yim los yog cov zis terminals.
Txuas lub teeb liab hlau kom raug.
Lub peev xwm ntawm lub teeb liab xaim hauv av yog sib npaug ntawm lub ntiaj teb, yog li tsis txhob txuas lub teeb liab xaim mus rau qhov siab voltage. Tsis txhob kov cov neeg raug mob los yog cov khoom.
Saib xyuas txhua qhov kev ntsuas dav dav.
Txhawm rau kom tsis txhob muaj hluav taws kub lossis hluav taws xob, thov saib xyuas txhua qhov kev ntsuas thiab kos npe cov lus qhia ntawm lub ntsuas.
Ua ntej txuas cov cuab yeej, thov nyeem phau ntawv qhia kom zoo kom tau txais cov ntaub ntawv ntxiv txog cov kev ntaus nqi.
Tsis txhob ua haujlwm nrog xav tias ua tsis tiav.
Yog tias koj xav tias cov khoom puas lawm, thov cia tsuas yog cov neeg ua haujlwm tsim nyog tau kuaj xyuas nws.
Tsis txhob raug hluav taws xob los yog xaim.
Tsis txhob kov cov neeg raug mob lossis cov khoom siv thaum lub hwj chim qhib.
Tsis txhob ua haujlwm ntub/damp tej yam kev mob.
Tsis txhob ua haujlwm hauv qhov chaw tawg.
Khaws qhov chaw ntawm qhov ntsuas kom huv si thiab qhuav.

Cov ntsiab lus kev nyab xeeb thiab cov cim

Cov ntsiab lus siv ntawm qhov ntsuas. Cov nqe lus yuav tshwm sim ntawm qhov ntsuas:
DANGER: Qhia txog kev raug mob lossis kev phom sij uas yuav tshwm sim tam sim ntawd.
CEEB TOOM: Qhia txog kev raug mob lossis kev phom sij uas yuav tsis tshwm sim tam sim ntawd.
CEEB TOOM: Qhia tau tias muaj kev puas tsuaj rau lub cuab yeej lossis lwm yam khoom yuav tshwm sim.
Cov cim siv rau ntawm qhov ntsuas. Cov cim yuav tshwm sim ntawm qhov ntsuas:

	Kev phom sij Voltage
	Tiv Thaiv Lub Ntiaj Teb
	Ceeb toom
	Chassis av
	Hloov fais fab

Taw qhia ntawm SDG2000X

Phau ntawv no suav nrog 3 tus qauv hauv qab no ntawm SDG2000X Series Function / Arbitrary Waveform Generators: SDG2042X, SDG2082X thiab SDG2122X.
SIGLENT's SDG2000X yog series ntawm dual-channel muaj nuj nqi / arbitrary waveform generators nrog specifications txog li 120MHz siab tshaj bandwidth, 1.2GSa / ssampling tus nqi thiab 16-ntsis ntsug kev daws teeb meem. Cov tswv yim TrueArb & EasyPulse cov tswv yim pab daws cov kev tsis muaj zog uas muaj nyob rau hauv cov khoom siv DDS ib txwm siv thaum tsim cov qauv tsim, square thiab mem tes waveforms. Siv cov tswv yim no SDG2000X muab cov neeg siv nrog ntau yam kev ntseeg siab, tsis tshua muaj suab nrov kom ua tau raws li qhov yuav tsum tau muaj rau ntau cov ntawv thov nyuaj.

Cov yam ntxwv tseem ceeb

◆ Dual-channel, 120MHz siab tshaj bandwidth, 20Vpp siab tshaj tawm amplitude, tso zis nrog 80dB dynamic ntau yam
◆ Kev ua haujlwm siab sampling system nrog 1.2GSa / ssampling tus nqi thiab 16-ntsis ntsug kev daws teeb meem. Tsis muaj kev nthuav dav hauv koj cov waveforms yuav ploj mus
◆ Lub tswv yim TrueArb thev naus laus zis, raws li qhov taw tes-los ntawm-point architecture, txhawb nqa ib qho 8pts ~ 8Mpts Arb waveform nrog raws liampLing tus nqi nyob rau hauv thaj tsam ntawm 1μSa / s ~ 75MSa / s
◆ Lub tswv yim yooj yim Pulse thev naus laus zis, muaj peev xwm ua kom qis qis qis qis qis los yog Pulse waveforms, nqa ntau yam thiab tsis tshua muaj siab precision hauv pulse dav thiab nce / poob lub sij hawm hloov
◆ Ntau hom kev hloov kho analog thiab digital: AM, DSB-AM, FM, PM, FSK, ASK, PSK thiab PWM
◆ cheb thiab tawg ua haujlwm
◆ Harmonic waveforms tsim muaj nuj nqi
◆ Waveforms sib txuas ua haujlwm
◆ High precision Frequency Counter
◆ 196 hom kev ua haujlwm tsis txaus ntseeg
◆ Standard interfaces: USB Host, USB Device (USBTMC), LAN (VXI-1 1) xaiv interface: GPIB
◆ 4.3" kov npo zaub kom ua haujlwm yooj yim dua

Pib nrawm

Tshooj lus no hais txog cov ncauj lus hauv qab no:

Kov kho tau
Pem hauv ntej / rear vaj huam sib luag
Xaiv ib Waveform
Mus Teeb Modulation/Sweep/Burst
Tig On/Off Output
Txhawm rau siv Numeric Input
Txhawm rau Siv Cov Ntsiab Lus Tseem Ceeb

1.1 Kov Kho
Txhawm rau kho txoj haujlwm ntawm SDG2000X, thov tuav tus tuav ntawm ob sab thiab rub tawm sab nraud.
Tom qab ntawd, ua kom tus kov tig mus rau txoj haujlwm xav tau.Daim duab 1-1 Viewing Position and Carrying Position
1.2 Pem hauv ntej / Rov Qab Vaj Huam Sib Luag
Tshooj lus no yuav muab cov lus qhia luv luv thiab piav qhia txog kev ua haujlwm thiab kev ua haujlwm ntawm lub vaj huam sib luag pem hauv ntej / nram qab.
Pem hauv ntej vaj huam sib luag
SDG2000X muaj lub ntsej muag meej thiab yooj yim pem hauv ntej uas suav nrog 4.3 nti kov npo, cov ntawv qhia zaub mov softkeys, cov lej keyboard, pob qhov rooj, ua haujlwm yuam sij, xub yuam sij, thiab channel tswj cheeb tsam, thiab lwm yam. Lub Vaj Huam Sib Luag
Lub vaj huam sib luag nram qab muab ntau qhov sib cuam tshuam, suav nrog Counter, 10MHz In/Out, Aux In/Out, LAN, USB Device, Earth Terminal thiab AC Power Supply Input. Kov Screen Zaub
SDG2000X tsuas tuaj yeem tso saib tsis tau thiab waveform ntawm ib channel ib zaug. Daim duab hauv qab no qhia txog qhov sib cuam tshuam thaum CH1 xaiv AM modulation ntawm sine waveform. Cov ntaub ntawv tso tawm tuaj yeem sib txawv nyob ntawm qhov ua haujlwm tau xaiv.
Tag nrho lub vijtsam ntawm SDG2000X yog lub vijtsam kov. Koj tuaj yeem siv koj daim duab lossis kov cwj mem los tswj lub ntsuas. Feem ntau cov haujlwm thiab cov kev xaiv tuaj yeem xaiv tau siv lub vijtsam kov zoo ib yam li cov yuam sij hauv pem hauv ntej thiab pob qhov rooj.

Waveform Display Area
Qhia qhov tam sim no xaiv waveform ntawm txhua channel.
Channel Status Bar
Qhia txog cov xwm txheej uas tau xaiv thiab tso tawm cov teeb tsa ntawm cov channel.

Basic Waveform Parameters Thaj Chaw
Qhia qhov tam sim no waveform qhov tsis muaj ntawm txhua channel. Nias Parameter thiab xaiv qhov sib thooj softkey los qhia qhov parameter kom teeb tsa. Tom qab ntawd siv tus lej yuam sij lossis pob qhov rooj los hloov tus nqi parameter.
Channel Parameters cheeb tsam
Qhia qhov chaw thau khoom thiab tso zis ntawm cov channel uas tau xaiv tam sim no.
Thauj khoom —-Tus nqi ntawm cov zis load, raws li tus neeg siv xaiv.
Xovxwm Utility → Output → Load , tom qab ntawd siv cov softkeys, tus lej yuam sij lossis pob qhov rooj hloov tus nqi parameter; los yog txuas ntxiv nias tus yuam sij tso zis rau ob thib ob los hloov ntawm High Impedance thiab 50Ω.
High impedance: tso saib HiZ.
Load: tso saib tus nqi impedance (lub neej ntawd yog 50Ω thiab qhov ntau yog 50Ω txog 100kΩ).
Nco tseg: Qhov kev teeb tsa no tsis tau hloov pauv qhov ntsuas qhov tso zis impedance ntawm 50Ω tab sis yog siv los tswj amplitude raug rau hauv qhov sib txawv load qhov tseem ceeb.
Output —-Channel output state.
Tom qab nias cov channel tso zis tswj chaw nres nkoj, cov channel tam sim no tuaj yeem qhib / tawm.

LAN Status Icon
SDG2000X yuav qhia cov lus ceeb toom sib txawv raws li cov xwm txheej hauv lub network tam sim no.
Cov cim no qhia tias kev sib txuas LAN ua tiav.
Cov cim no qhia tias tsis muaj kev sib txuas LAN lossis kev sib txuas LAN tsis ua tiav.
Hom Icon
SDG2000X yuav qhia cov lus ceeb toom sib txawv raws li hom tam sim no.
Cov cim no qhia tias hom tam sim no yog Phase-locked.
Cov cim no qhia tias hom tam sim no yog ywj pheej.

Ntawv qhia zaub mov
Qhia cov ntawv qhia zaub mov sib raug rau cov haujlwm uas pom. Rau example, Daim duab 1-4 Touch Screen Display qhia qhov tsis muaj "AM modulation".
Modulation Parameters Thaj Chaw
Qhia qhov tsis muaj ntawm qhov kev ua haujlwm tam sim no. Tom qab xaiv cov ntawv qhia zaub mov sib raug, siv tus lej yuam sij lossis pob qhov rooj hloov tus nqi parameter.

Clock Source Icon
Cov cim no qhia tias lub moos tam sim no yog qhov chaw sab hauv.
Cov cim no qhia tau hais tias lub moos tam sim no tsis muaj nyob rau sab nraud
Cov cim no qhia tias lub moos tam sim no yog qhov chaw sab nraud.

1.3 Xaiv lub Waveform
Nias Waveforms nkag mus rau hauv cov ntawv qhia zaub mov raws li daim duab 1-5 qhia. Cov example hauv qab no yuav pab kom paub txog cov kev xaiv waveform.

Xovxwm Waveforms key thiab ces nias Sitsis yog softkey. SDG2000X tuaj yeem tsim sine waveforms nrog zaus ntawm 1μHz txog 120MHz. Los ntawm kev teeb tsa zaus / Lub Sijhawm, Amplitude/High level, Offset/Low level thiab Phase, ib lub teeb liab sine uas muaj qhov sib txawv tuaj yeem tsim tau.
Xovxwm Waveforms key thiab ces nias Square softkey. Lub tshuab hluav taws xob tuaj yeem tsim cov square waveforms nrog zaus ntawm 1μHz txog 25MHz thiab hloov pauv lub luag haujlwm. Los ntawm kev teeb tsa zaus / Lub Sijhawm, Amplitude/High level, Offset/Low level, Phase and DutyCycle, square waveform with different parameters can be generated.

Xovxwm Waveforms key thiab ces nias Ramp softkey. Lub tshuab hluav taws xob tuaj yeem tsim ramp waveforms nrog zaus ntawm 1μHz mus rau 1MHz thiab sib txawv symmetry. Los ntawm kev teeb tsa zaus / Lub Sijhawm, Amplitude/High level, Offset/Low level, Phase and Symmetry, aramp waveform nrog cov tsis sib txawv tuaj yeem tsim tau.
Xovxwm Waveforms key thiab ces nias mem tes softkey. Lub tshuab hluav taws xob tuaj yeem tsim cov mem tes waveforms nrog zaus ntawm 1μHz txog 25 MHz thiab sib txawv pulse dav thiab nce / poob lub sij hawm. Los ntawm kev teeb tsa zaus / Lub Sijhawm, Amplitude/High level, Offset/Low level, Pu l Dav/Duty, Rise/fall and delay, pulse waveform with different parameters can be generated.

Xovxwm Waveforms key thiab ces nias Suab nrov softkey. Lub tshuab hluav taws xob tuaj yeem tsim suab nrov nrog bandwidth ntawm 20MHz txog 120MHz. Los ntawm kev teeb tsa Stdev thiab Mean, suab nrov nrog cov ntsuas sib txawv tuaj yeem tsim tawm.
Xovxwm Waveforms key thiab ces nias Nplooj 1/2, kawg nias lub DC softkey. Lub tshuab hluav taws xob tuaj yeem tsim hluav taws xob DC nrog qib siab txog ± 10V rau hauv HighZ load lossis ± 5V rau hauv 50Ω load.

Xovxwm Waveforms key thiab ces nias Nplooj 1/2, kawg nias lub Arb softkey. Lub tshuab hluav taws xob tuaj yeem tsim cov kev hloov pauv tsis tu ncua nrog qhov ntev ntawm 8 txog 8M cov ntsiab lus thiab zaus mus txog 20MHz. Los ntawm kev teeb tsa zaus / Lub Sijhawm, Amplitude/High level, Offset/Low level, Phase and Arb mode, a arbitrary signal with different parameters can be generated.

1.4 Teeb Modulation/Sweep/Burst
Raws li pom nyob rau hauv daim duab 1-13, muaj peb lub hauv paus ntawm lub vaj huam sib luag pem hauv ntej uas yog siv rau kev hloov kho, cheb thiab tawg. Cov lus qhia hauv qab no yuav pab piav qhia txog cov haujlwm no.

Nyem Mod, Modulation muaj nuj nqi yuav qhib.
Lub modulated waveform tuaj yeem hloov pauv los ntawm kev hloov pauv qhov tsis xws li Hom, Qhov Chaw, AM Qhov tob, AM Freq, Shape, thiab lwm yam. Lub SDG2000X tuaj yeem hloov pauv waveforms siv AM, FM, PM, ASK, FSK, PSK, PWM thiab DSB-AM, thiab lwm yam. Pulse waveforms tsuas tuaj yeem hloov kho siv PWM. Lub suab nrov thiab DC waveforms tsis tuaj yeem hloov kho.
Nias Sweep, Sweep muaj nuj nqi yuav qhib.
Sib, square, ramp thiab arbitrary waveforms txhawb lub cheb muaj nuj nqi. Hauv hom cheb, SDG2000X tuaj yeem tsim cov cim nrog qhov sib txawv. Lub sijhawm cheb muaj nyob ntawm 1ms txog 500s. Lub hauv paus ntsiab lus tuaj yeem yog "Internal", "External" lossis "Manual".

Nias Burst, Burst muaj nuj nqi yuav qhib.
Cov teeb liab tawg rau sine, square, ramp, pulse los yog arbitrary waveforms yuav raug generated. Pib Phase yog li ntawm 0 ° txog 360 ° thiab Lub Sijhawm tawg yog li ntawm 1μs txog 1000s.

1.5 Txhawm rau qhib / tawm cov zis
Raws li pom nyob rau hauv daim duab 1-17 muaj ob tug yuam sij nyob rau sab xis ntawm lub lag luam vaj huam sib luag uas yog siv los pab / lov tes taw cov zis ntawm ob txoj kev. Xaiv ib qho channel thiab nias qhov sib txuas Tso zis qhov tseem ceeb, qhov tseem ceeb backlight yuav teeb thiab cov zis yuav qhib. Nias lub Tso zis tseem ceeb dua, tus yuam sij backlight yuav raug tua thiab cov zis yuav raug xiam.
Cia nias tus yuam sij tso zis rau ob vib nas this los hloov ntawm High Impedance thiab 50Ω load. 1.6 Txhawm rau siv cov lej nkag
Raws li pom hauv daim duab 1-18, muaj peb txheej ntawm cov yuam sij ntawm lub vaj huam sib luag pem hauv ntej, uas yog cov yuam sij xub, pob qhov rooj thiab cov lej keyboard. Cov lus qhia hauv qab no yuav pab kom koj paub txog kev xaiv cov tswv yim digital.

Tus lej keyboard yog siv los nkag rau qhov ntsuas tus nqi.
Lub pob qhov rooj yog siv los nce (clockwise) lossis txo qis (counterclockwise) tus lej tam sim no thaum teeb tsa qhov ntsuas

Thaum siv cov pob qhov rooj los teeb tsa, cov cim xub siv los xaiv tus lej los hloov kho; Thaum siv cov lej keyboard los teeb tsa qhov tsis muaj, tus yuam sij sab laug yog siv los ua Backspace muaj nuj nqi.

1.7 Txhawm rau Siv Cov Ntsiab Lus Tseem Ceeb
Raws li pom hauv daim duab 1-19, muaj tsib tus yuam sij ntawm lub vaj huam sib luag ua haujlwm, uas tau sau npe Parameter, Utility, Store / Recall, Waveforms, thiab Ch1 / Ch2. Cov lus qhia hauv qab no yuav pab kom koj paub txog cov haujlwm no.

Cov Parameter qhov tseem ceeb ua rau nws yooj yim rau tus neeg teb xov tooj los teeb tsa cov kev txwv ntawm cov qauv waveforms ncaj qha.
Cov Kev siv hluav taws xob Qhov tseem ceeb yog siv los teeb tsa lub koom haum pab cuam, xws li cov khoom tsim tawm, kev teeb tsa kev sib txuas, kev teeb tsa cov ntaub ntawv, ua qhov ntsuas tus kheej ntsuas thiab nyeem cov ntaub ntawv calibration, thiab lwm yam.
Cov Khw/Rau qhov tseem ceeb yog siv los khaws thiab khaws cov ntaub ntawv waveform thiab cov ntaub ntawv teeb tsa.
Cov Waveforms key yog siv los xaiv cov waveforms yooj yim.
Cov Ch1/Ch2 tus yuam sij yog siv los hloov qhov tam sim no xaiv channel ntawm CH1 thiab CH2. Tom qab pib, CH1 raug xaiv raws li lub neej ntawd. Ntawm no, nias tus yuam sij xaiv CH2.

Kev ua haujlwm pem hauv ntej

Txog rau tam sim no, koj tau txais kev nkag siab luv luv txog SDG2000X nrog rau pem hauv ntej / nram qab vaj huam sib luag, txhua qhov chaw tswj kev ua haujlwm thiab cov yuam sij. Koj yuav tsum paub yuav ua li cas los teeb tsa koj qhov Function / Arbitrary Waveform Generator rau koj siv. Yog tias koj tsis paub txog cov haujlwm no, koj raug hais kom nyeem tshooj ib 'Quick Start' dua.
Tshooj lus no hais txog cov ncauj lus hauv qab no:

Rau Teem Sine
Rau Teeb Square
Rau Set Ramp
Txhawm rau teeb Pulse
Mus Teeb Noise
Rau Set DC
Txhawm rau teem Arbitrary
Txhawm rau teeb tsa Harmonic Function
Mus Teeb Modulation Function
Txhawm rau teeb tsa Sweep Function
Txhawm rau teeb tsa Burst Function
Mus Khaws thiab Rov Qab
Txhawm rau teeb Utility Function

Nws raug nquahu kom koj nyeem tshooj no ua tib zoo kom nkag siab txog SDG2000X qhov ntau yam waveform teeb tsa ua haujlwm thiab cov txheej txheem ua haujlwm ntxiv.

2.1 Rau Teem Sine Waveform
Xovxwm Waveforms yuam kom xaiv lub waveform muaj nuj nqi thiab ces nias lub Sine softkey. Cov sine waveform tsis yog teem los ntawm kev siv cov ntawv qhia ua haujlwm sine.
Cov tsis muaj rau sine waveforms muaj xws li zaus/lub sij hawm, amplitude / qib siab, offset / qis theem thiab theem. Sib txawv sine signals tuaj yeem tsim los ntawm kev teeb tsa cov kev txwv no. Raws li pom hauv daim duab 2-1, hauv cov ntawv qhia zaub mov tseem ceeb, xaiv Ntau zaus . Lub cheeb tsam zaus yog qhov tseem ceeb nyob rau hauv parameter zaub qhov rai, thiab cov neeg siv tuaj yeem teeb tsa tus nqi zaus ntawm no.Table 2-1 Menu Kev piav qhia ntawm Sine Waveform

Muaj nuj nqi zaub mov	Chaw	Kev piav qhia
Zaus / Lub Sijhawm		Teem lub teeb liab zaus lossis lub sijhawm; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Amplitude/HighLevel		Teeb lub teeb liab amplitude los yog qib siab; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Offset / LowLevel		Teem lub teeb liab offset lossis qib qis; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Theem		Teem lub theem ntawm lub teeb liab.

Txhawm rau Teem Lub Sijhawm / Lub Sijhawm
Zaus yog ib qho tseem ceeb tshaj plaws ntawm cov qauv waveforms. Rau cov qauv ntsuas sib txawv thiab cov qauv waveforms, qhov muaj ntau zaus sib txawv. Yog xav paub ntxiv, thov mus saib "SDG2000X Datasheet". Lub neej ntawd zaus yog 1kHz.

Xovxwm Waveforms → Sine → Zaus , los teeb qhov zaus parameter.
Cov zaus uas pom ntawm lub vijtsam thaum lub ntsuas hluav taws xob yog lub neej ntawd tus nqi lossis tus nqi ntawm lub zog kawg. Yog Lub Sijhawm (tsis yog Zaus) yog qhov xav tau, nias zaus / Lub Sijhawm dua kom nkag mus rau Lub Sijhawm hom. Tus nqi tam sim no rau lub sij hawm waveform yog tam sim no tso tawm nyob rau hauv cov xim inverse. Nias lub Zaus / Lub Sijhawm yuam sij ib zaug ntxiv kom rov qab mus rau zaus nkag hom.
Nkag mus rau qhov xav tau zaus.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha, thiab nias tus yuam sij coj los xaiv lub parameter unit. Los yog siv tus xub yuam sij los xaiv tus lej los hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi.

Nco tseg:
Thaum siv tus lej keyboard kom nkag mus rau tus nqi, tus yuam sij sab laug tuaj yeem siv los txav tus cursor rov qab thiab tshem tawm tus nqi ntawm tus lej dhau los.
Mus teem lub Amptoj siab
Cov ampLitude teeb tsa ntau yam yog txwv los ntawm "Load" thiab "Frequency / Period" settings. Yog xav paub ntxiv, thov mus saib "SDG2000X Datasheet".

Xovxwm Waveforms → Sine → Amptoj siab , mus set amptoj siab.
Cov amplitude pom ntawm qhov screen thaum lub ntsuas hluav taws xob yog lub neej ntawd tus nqi lossis tus nqi ntawm lub zog kawg. Yog xav tau kev teeb tsa waveform siab, nias lub Amplitude / HighLevel tus yuam sij dua hloov mus rau qhov ntsuas qib siab (qhov kev ua haujlwm tam sim no tau tshwm sim hauv cov xim sib txawv).
Nkag mus rau qhov xav tau amptoj siab.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha, thiab nias tus yuam sij coj los xaiv lub parameter unit. Los yog siv tus xub yuam sij los xaiv tus lej los hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi.

Txhawm rau teeb tsa Offset
Qhov kev teeb tsa offset yog txwv los ntawm "Load" thiab "Amplitude/HighLevel” nqis. Yog xav paub ntxiv, thov mus saib "SDG2000X Datasheet". Tus nqi pib yog 0Vdc.

Nias Waveforms → Sine → Offset, los teeb qhov offset.
Qhov offset pom ntawm qhov screen thaum lub ntsuas hluav taws xob yog lub neej ntawd tus nqi lossis tus nqi ntawm lub zog kawg. Yog tias koj xav teem lub waveform los ntawm qib qis, nias lub Offset/LowLevel tseem ceeb dua, hloov mus rau qhov ntsuas qis qis (qhov kev ua haujlwm tam sim no tau tshwm sim hauv cov xim sib txawv).

Nkag mus rau qhov xav tau offset.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha, thiab nias tus yuam sij coj los xaiv lub parameter unit. Los yog siv tus xub yuam sij los xaiv tus lej los hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi.

Txhawm rau teem caij

Nias Waveforms → Sine → Phase , los teeb lub theem.
Theem qhia ntawm qhov screen thaum lub ntsuas yog powered on yog lub neej ntawd tus nqi los yog cov txheej txheem ntawm lub hwj chim kawg.
Nkag mus rau theem uas xav tau.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha thiab nias tus yuam sij coj los xaiv lub parameter unit. Los yog siv tus xub yuam sij los xaiv tus lej los hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi.

Nco tseg:
Thaum lub hom kev ywj pheej qhib, cov theem parameter tsis tuaj yeem hloov kho
2.2 Rau Teem Square Waveform
Nias Waveforms qhov tseem ceeb los xaiv lub waveform muaj nuj nqi, thiab nias lub Square softkey. Cov square waveform parameters tau teeb tsa los ntawm kev siv cov ntawv qhia ua haujlwm Square.
Cov tsis muaj square waveforms muaj xws li zaus/lub sij hawm, amplitude / qib siab, offset / qis qis, theem thiab lub luag haujlwm. Raws li pom hauv daim duab 2-6, xaiv DutyCycle . Lub luag hauj lwm voj voog parameter cheeb tsam yog tseem ceeb nyob rau hauv lub parameter zaub qhov rais, thiab cov neeg siv yuav teem lub luag hauj lwm voj voog nqi ntawm no.

Table 2-2 Menu Kev piav qhia ntawm Square Waveform

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Zaus / Lub Sijhawm		Teem lub teeb liab zaus lossis lub sijhawm; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Amplitude/HighLevel		Teeb lub teeb liab amplitude los yog qib siab; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Offset / LowLevel		Teem lub teeb liab offset lossis qib qis; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Theem		Teem lub theem ntawm lub teeb liab.
DutyCycle		Teem lub luag haujlwm voj voog rau square waveform.

Kom Teem Lub Luag Haujlwm Cycle
Lub luag haujlwm Cycle: Qhov piv ntawm lub sij hawm tus mem tes yog nyob rau hauv lub xeev siab thiab lub waveform lub sij hawm.Lub luag haujlwm lub voj voog teeb tsa ntau yam yog txwv los ntawm "Frequency / Period" chaw. Yog xav paub ntxiv, thov mus saib "SDG2000X Datasheet". Tus nqi qub yog 50%.

Xovxwm Waveforms → Square → DutyCycle , los teeb lub voj voog ua haujlwm.
Lub voj voog ua haujlwm tau pom ntawm qhov screen thaum lub ntsuas hluav taws xob yog lub neej ntawd tus nqi lossis tus nqi ntawm lub zog kawg.
Nkag mus rau lub luag haujlwm uas xav tau.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha thiab nias tus yuam sij coj los xaiv lub parameter unit. Los yog siv tus xub yuam sij los xaiv tus lej los hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi. Lub tshuab hluav taws xob yuav hloov lub waveform tam sim ntawd.

Nco tseg:
Cov txheej txheem ntawm kev teeb tsa lwm qhov tsis sib xws ntawm cov teeb liab square zoo ib yam li sine waveform muaj nuj nqi.

2.3 Rau Set Ramp Waveform
Xovxwm Waveforms tus yuam sij xaiv lub waveform muaj nuj nqi, thiab nias lub Ramp softkey. Cov ramp waveform parameters yog teem los ntawm kev siv ramp cov ntawv qhia ua haujlwm.
Parameters rau ramp waveforms suav nrog zaus / lub sijhawm, amplitude/high level, offset/low level, theem thiab symmetry. Raws li pom hauv daim duab 2-8, hauv cov ntawv qhia zaub mov tseem ceeb, xaiv Symmetry . Lub symmetry parameter cheeb tsam yog highlighted nyob rau hauv lub parameter zaub qhov rais, thiab cov neeg siv yuav teem lub symmetry tus nqi ntawm no. Table 2-3 Menu Lus piav qhia ntawm Ramp Waveform

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Zaus / Lub Sijhawm		Teem lub teeb liab zaus lossis lub sijhawm; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Amplitude/HighLevel		Teeb lub teeb liab amplitude los yog qib siab; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Offset / LowLevel		Teem lub teeb liab offset lossis qib qis; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Theem		Teem lub theem ntawm lub teeb liab.
Symmetry		Teem lub symmetry rau ramp waveform.

Txhawm rau teeb tsa Symmetry
Symmetry: Qhov percentage tias lub sijhawm nce yuav siv sijhawm tag nrho.
Cov tswv yim ntau: 0 ~ 100%
Default Tus Nqi: 50%

Xovxwm Waveforms → Ramp → Symmetry, los teeb lub symmetry.
Lub symmetry pom ntawm lub vijtsam thaum lub ntsuas hluav taws xob yog lub neej ntawd tus nqi lossis tus nqi ntawm lub zog kawg.

Nkag mus rau qhov xav tau Symmetry.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha, thiab nias tus yuam sij coj los xaiv lub parameter unit. Los yog siv tus xub yuam sij los xaiv tus lej los hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi. Lub tshuab hluav taws xob yuav hloov lub waveform tam sim ntawd.

Nco tseg:
Cov txheej txheem ntawm kev teeb tsa lwm yam tsis muaj ramp teeb liab zoo ib yam li sine waveform muaj nuj nqi.
2.4 Teeb Pulse Waveform
Xovxwm Waveforms tus yuam sij xaiv lub waveform muaj nuj nqi, thiab nias lub mem tes softkey. Pulse waveform parameters yog teem los ntawm kev siv lub tshuab pulse ua haujlwm.
Cov kev ntsuas rau pulse waveforms suav nrog zaus / lub sijhawm, amplitude/high level, offset/low level, dav, nce / poob thiab ncua. Raws li pom hauv daim duab 2-10, hauv cov ntawv qhia zaub mov tseem ceeb, xaiv PulWidth . Lub pulse width parameter cheeb tsam yog highlighted nyob rau hauv parameter zaub qhov rais, thiab cov neeg siv yuav teem lub mem tes dav tus nqi ntawm no.Table 2-4 Menu Kev piav qhia ntawm Pulse Waveform

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Zaus / Lub Sijhawm		Teem lub teeb liab zaus lossis lub sijhawm; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Amplitude/HighLevel		Teeb lub teeb liab amplitude los yog qib siab; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Offset / LowLevel		Teem lub teeb liab offset lossis qib qis; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
PulWidth / DutyCycle		Teem lub teeb liab mem tes dav lossis lub voj voog ua haujlwm; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Nce / Caij nplooj zeeg		Teem lub nce ntug los yog poob ntug rau pulse waveform. Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
ncua		Teem qhov ncua sij hawm rau pulse waveform.

Txhawm rau Teem Lub Pulse Dav / DutyCycle
Pulse dav txhais tau tias yog lub sijhawm los ntawm 50% qhov pib ntawm qhov nce siab amplitude mus rau 50% qhov pib ntawm lub caij nplooj zeeg tom ntej amplitude (raws li qhia hauv daim duab hauv qab no). Qhov dav pulse qhov chaw yog txwv los ntawm qhov "Mimum Pulse Width" thiab "Pulse Period" chaw. Yog xav paub ntxiv, thov mus saib "SDG2000X Datasheet". Lub neej ntawd tus nqi yog 200μs.
Pulse duty cycle yog txhais raws li qhov percentage hais tias lub mem tes dav siv nyob rau hauv tag nrho lub sij hawm. Pulse duty cycle thiab mem tes dav yog sib txheeb. Thaum ib qho kev hloov pauv, lwm qhov yuav raug hloov pauv.

Nias Waveforms → Pulse → PulWidth , los teeb lub mem tes dav.
Cov mem tes dav pom ntawm qhov screen thaum lub ntsuas hluav taws xob yog lub neej ntawd tus nqi lossis tus nqi ntawm lub zog kawg. Yog tias koj xav teeb tsa lub waveform los ntawm lub luag haujlwm, nias lub khawm PulWidth / DutyCycle dua, hloov mus rau hauv lub luag haujlwm parameter (qhov kev ua haujlwm tam sim no tau tshwm sim hauv cov xim inverse).
Nkag mus rau qhov xav tau Pulse Width.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha, thiab nias tus yuam sij coj los xaiv lub parameter unit. Los yog siv tus xub yuam sij los xaiv tus lej los hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi. Lub tshuab hluav taws xob yuav hloov lub waveform tam sim ntawd.

Txhawm rau Teem Rise/Fall Edge
Lub sijhawm nce ntug yog txhais raws li lub sijhawm ntawm lub plawv dhia amplitude nce los ntawm 10% mus rau 90% pib, thaum lub sij hawm lub caij nplooj zeeg yog txhais raws li lub sij hawm ntawm lub mem tes ampLitude txav los ntawm 90% mus rau 10% pib. Qhov teeb tsa ntawm lub sijhawm nce / poob ntug yog txwv los ntawm qhov tam sim no teev mem tes dav txwv. Cov neeg siv tuaj yeem teeb tsa ntug nce thiab poob ntug ntawm nws tus kheej.

Nias Waveforms → Pulse → Rise kom teem lub nce ntug.
Qhov sawv ntsug pom ntawm qhov screen thaum lub ntsuas hluav taws xob yog lub neej ntawd tus nqi lossis tus nqi ntawm lub zog kawg. Yog hais tias koj xav teem lub waveform los ntawm lub caij nplooj zeeg ntug, nias lub Nce / Poob tseem ceeb dua, hloov mus rau hauv lub caij nplooj zeeg ntug parameter (qhov tam sim no peration yog tso tawm nyob rau hauv inverse xim).
Nkag mus rau qhov xav tau nce ntug.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha, thiab nias tus yuam sij coj los xaiv lub parameter unit. Los yog siv tus xub yuam sij los xaiv tus lej los hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi. Lub tshuab hluav taws xob yuav hloov lub waveform tam sim ntawd.

Nco tseg:
Cov txheej txheem ntawm kev teeb tsa lwm yam tsis muaj teeb liab mem tes zoo ib yam li sine waveform muaj nuj nqi.

2.5 Txhawm rau teeb tsa suab nrov Waveform
Xovxwm Waveforms tus yuam sij xaiv lub waveform muaj nuj nqi, thiab nias lub Suab nrov softkey. Cov suab nrov tsis raug teeb tsa los ntawm kev siv lub suab nrov ua haujlwm. Cov tsis muaj suab nrov muaj xws li stdev, txhais tau tias thiab bandwidth. Raws li pom hauv daim duab 2-13, hauv cov ntawv qhia zaub mov tseem ceeb, xaiv Stdev , qhov chaw stdev parameter yog qhov tseem ceeb nyob rau hauv parameter zaub qhov rais, thiab cov neeg siv tuaj yeem teeb tsa tus nqi stdev ntawm no. Lub suab nrov yog cov teeb liab tsis yog lub caij nyoog uas tsis muaj zaus lossis lub sijhawm. Table 2-5 Menu Lus piav qhia txog suab nrov

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
BandSet		Qhib / tawm qhov kev teeb tsa bandwidth.
Stdev		Teem lub stdev rau suab nrov waveform.
Txhais tau tias		Teem lub ntsiab lus rau suab nrov waveform.
Bandwidth		Teem lub bandwidth rau suab nrov waveform.

Txhawm rau teeb tsa Stdev

Nias Waveforms → Suab nrov → Stdev , txhawm rau teeb tsa stdev.
Lub stdev qhia ntawm lub vijtsam thaum lub ntsuas hluav taws xob yog lub neej ntawd tus nqi lossis tus nqi ntawm lub zog kawg.
Nkag mus rau qhov xav tau stdev.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha, thiab nias tus yuam sij coj los xaiv lub parameter unit. Los yog siv tus xub yuam sij los xaiv tus lej los hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi.

Kom Teeb Mean

Nias Waveforms → Suab nrov → Mean , los teeb qhov txhais tau tias.
Qhov txhais tau tias pom ntawm qhov screen thaum lub ntsuas hluav taws xob yog lub neej ntawd tus nqi lossis tus nqi teev ntawm lub hwj chim kawg.
Nkag siab qhov xav tau.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha, thiab nias tus yuam sij coj los xaiv lub parameter unit. Los yog siv tus xub yuam sij los xaiv tus lej los hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi.

Kom Teem Bandwidth

Nias Waveforms → Suab nrov → BandSet thiab xaiv "On" los teeb tsa lub bandwidth.
Cov bandwidth qhia ntawm qhov screen thaum lub ntsuas hluav taws xob yog lub neej ntawd tus nqi lossis tus nqi teev ntawm lub hwj chim kawg. Thaum hloov qhov kev ua haujlwm, yog tias tus nqi tam sim no siv tau rau cov qauv waveform tshiab, nws yuav siv tau raws li qhov xav tau.

Nkag mus rau qhov xav tau bandwidth.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha, thiab nias tus yuam sij coj los xaiv lub parameter unit. Lossis koj tuaj yeem siv tus yuam sij xub los xaiv tus lej koj xav hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi.

2.6 Teeb DC Waveform
Nias Waveforms → Nplooj 1/2 → DC , kom nkag mus rau hauv qab no interface. Thov nco ntsoov tias muaj 'DC offset' parameter ntawm nruab nrab ntawm qhov screen.Nco tseg:
Txoj kev teeb tsa offset ntawm DC teeb liab zoo ib yam li sine waveform muaj nuj nqi.
2.7 Txhawm rau Teem Lub Waveform
Arb teeb liab muaj ob hom: lub kaw lus tsim-hauv waveforms thiab cov neeg siv-txhais waveforms. Built-in waveforms yog khaws cia rau hauv lub cim xeeb uas tsis yog-volatile. Cov neeg siv kuj tseem tuaj yeem hloov kho qhov arbitrary waveform nrog 8 mus rau 8M cov ntaub ntawv cov ntsiab lus, uas yog 8pts rau 8Mpts.
DDS
Xaiv Waveforms → Nplooj 1/2 → Arb → Arb Hom athiab xaiv "DDS" hom tso zis. Cov tsis muaj xws li zaus/lub sij hawm, amplitude / qib siab, offset / qis theem thiab theem.
Tmuaj peev xwm 2-6 Cov Lus Qhia Piav Qhia ntawm Arb Waveform (Page 1/2)

Muaj nuj nqi zaub mov	Chaw	Kev piav qhia
Zaus / Lub Sijhawm		Teem lub teeb liab zaus lossis lub sijhawm; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Amplitude/HighLevel		Teeb lub teeb liab amplitude los yog qib siab; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Offset / LowLevel		Teem lub teeb liab offset lossis qib qis; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Theem		Teem lub theem ntawm lub teeb liab.

Hauv DDS cov zis hom, cov neeg siv tuaj yeem teeb tsa qhov zaus lossis lub sijhawm ntawm qhov tsis txaus ntseeg waveform. Lub ntsuas hluav taws xob tso tawm ib qho arbitrary waveform uas yog tsim los ntawm qee cov ntsiab lus raws li qhov zaus tam sim no
TrueArb
Xaiv Waveforms → Page 1/2 → Arb → Arb Hom thiab xaiv "TrueArb" tso zis hom. Cov tsis muaj xws li samptus nqi / zaus, amplitude / qib siab, offset / qis theem thiab theem. Table 2-7 Menu Kev piav qhia ntawm Arb Waveform (Page 1/2)

Muaj nuj nqi zaub mov	Chaw	Kev piav qhia
SRate / Zaus		Teeb lub teeb liab sampling tus nqi lossis zaus; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Amplitude/HighLevel		Teeb lub teeb liab amplitude los yog qib siab; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Offset / LowLevel		Teem lub teeb liab offset lossis qib qis; Qhov ntsuas tam sim no yuav raug hloov ntawm lub xovxwm thib ob.
Theem		Teem lub theem ntawm lub teeb liab.

Hauv TrueArb tso zis hom, cov neeg siv tuaj yeem teeb tsa sampling tus nqi (cov ntsiab lus tso tawm ib ob) los yog zaus ntawm qhov arbitrary waveform. Cov cuab yeej tso tawm ib qho arbitrary waveform point los ntawm taw tes raws li qhov tam sim no sampling nqi.
Txhawm rau teeb tsa SampLing Tus Nqi

Xovxwm Waveforms → Nplooj 1/2 → Arb → TureArb → Srate , set samptus nqi parameter.
Qhov sampling tus nqi qhia nyob rau ntawm qhov screen thaum lub ntsuas yog powered on yog lub neej ntawd tus nqi lossis tus nqi ntawm lub hwj chim kawg. Thaum teeb tsa lub luag haujlwm, yog tias tus nqi tam sim no siv tau rau cov qauv waveform tshiab, nws yuav siv tau raws li qhov xav tau. Yog tias koj xav teeb tsa qhov zaus rau lub waveform, nias SRate / Zaus yuam sij dua, hloov mus rau qhov tsis muaj zaus (qhov kev ua haujlwm tam sim no tshwm nyob rau hauv cov xim inverse).
Nkag mus rau qhov xav tau sampling nqi.
Siv tus lej keyboard kom nkag mus rau tus nqi parameter ncaj qha, thiab nias tus yuam sij coj los xaiv lub parameter unit. Lossis koj tuaj yeem siv tus yuam sij xub los xaiv tus lej koj xav hloov kho, thiab tom qab ntawd siv lub pob khawm hloov nws tus nqi.

Nco tseg:
Cov txheej txheem ntawm kev teeb tsa qhov tsis sib xws ntawm cov teeb liab arbitrary zoo ib yam li sine waveform muaj nuj nqi.
Xaiv lub built-in Arbitrary Waveform
Muaj ntau qhov tsim-hauv Arbitrary Waveforms thiab cov neeg siv-txhais Arbitrary Waveforms hauv lub tshuab hluav taws xob. Txhawm rau xaiv ib qho ntawm lawv, ua raws li cov lus qhia hauv qab no.

Xaiv lub Built-in Waveform
Xaiv Waveforms → Page 1/2 → Arb → Arb Hom → Built-In nkag mus rau hauv cov interface nram qab no, raws li qhia hauv daim duab 2-21.

Nias Common , Lej , Cav , Qhov rai , Trigo lossis lwm cov ntawv qhia zaub mov hloov mus rau qeb yam xav tau (cov qeb xaiv hauv cov ntawv qhia zaub mov tseem ceeb), tom qab ntawd tig lub pob qhov rooj lossis nyem lub vijtsam kov los xaiv qhov xav tau waveform (qhov xaiv waveform yog tseem ceeb). Xaiv Txais los yog nias lub pob khawm kom rov qab tau cov ntaub ntawv sib thooj.
Table 2-8 Built-in Waveforms

Yam khoom	Waveform	Kev piav qhia
Feem ntau	StairUp	Stair-up waveform
	StairDn	Stair-down waveform
	StairUD	Stair-up thiab down waveform
	Trapezia	Trapezia waveform
	Ppulse	Pulse zoo
	Npulse	Negative mem tes
	UpRamp	UpRamp waveform
	DnRamp	DnRamp waveform
	SineTra	Sine-Tra waveform
	SineVer	Sine-Ver waveform
lej	ExpFall	ExpFall muaj nuj nqi
	ExpRise	ExpRise muaj nuj nqi
	LogFall	LogFall muaj nuj nqi
	LogRise	LogRise muaj nuj nqi
	Sqrt	Sqrt muaj nuj nqi
	Hauv paus 3	Root3 muaj nuj nqi

	X^2	X2 muaj nuj nqi
	X^3	X3 muaj nuj nqi
	Huab cua	Airy muaj nuj nqi
	Besselj	Bessel kuv ua haujlwm
	Bessely	Bessel II function
	Dirichlet	Dirichlet muaj nuj nqi
	Erf	Ua haujlwm yuam kev
	Erfc	Complementary yuam kev muaj nuj nqi
	ErfcInv	Inverted complementary yuam kev muaj nuj nqi
	ErfInv	Inverted yuam kev ua haujlwm
	Laguerre	4-lub sij hawm Laguerre polynomial
	Lus dab neeg	5-lub sij hawm Legend polynomial
	Versiera	Versiera
	Sinc	Sinc muaj nuj nqi
	Gaussian	Gaussian muaj nuj nqi
	Dlorentz	Dlorentz muaj nuj nqi
	Haversine	Haversine muaj nuj nqi
	Lorentz	Lorentz muaj nuj nqi
	Gauspuls	Gauspuls teeb liab
	Gmonopuls	Gmonopuls teeb liab
	Tripuls	Tripuls teeb liab
	Weibull	Weibull kev faib tawm
	LogNormal	LogNormal Gaussian faib
	Laplace	Kev faib tawm
	Maxwell	Maxwell faib
	Rayleigh	Kev faib tawm Rayleigh
	Cauchy	Cauchy faib
Cav	Mob plawv	Cardiac signal
	Quake	Analog quake waveform
	Chirp	Chirp signal
	TwoTone	TwoTone teeb liab
	SNR	SNR teeb liab
	AmpALT	Tau txais oscillation nkhaus
	AttALT	Attenuation oscillation nkhaus
	RoundHalf	RoundHalf Waveform

	RoundsPM	RoundsPM Waveform
	BlaseiWave	Lub sij hawm-velocity nkhaus ntawm tawg oscillation
	DampedOsc ua	Lub sij hawm xaav nkhaus ntawm damped oscillation
	SwingOsc	Kinetic zog - lub sij hawm nkhaus ntawm viav vias oscillation
	Tso tawm	Tshem tawm nkhaus ntawm NI-MH roj teeb
	Pahcur	Tam sim no waveform ntawm DC brushless lub cev muaj zog
	Ua ke	Kev sib xyaw ua haujlwm
	SCR	SCR firing profile
	TV	TV teeb liab
	Suab	Lub suab teeb liab
	Surge	Surge teeb liab
	Ripple	Ripple nthwv dej ntawm roj teeb
	Gamma	Gamma teeb liab
	StepResp	Kauj ruam teb teeb liab
	BandLimited	Bandwidth-limited teeb liab
	CPulse	C-Pulse
	CWPulse	CW mem tes
	GateVibr	Rooj vag tus kheej oscillation teeb liab
	LFMPulse	Linear FM mem tes
	MCNoise	Mechanical tsim suab nrov
Qhov rai	Hamming	Hamming qhov rais
	Hanning	Hanning qhov rais
	Kaiser	Kaiser qhov rais
	Blackman	Blackman qhov rais
	GaussiWin	GaussiWin qhov rais
	Daim duab peb sab	Daim duab peb sab qhov rais (Fejer qhov rais)
	BlackmanH	BlackmanH qhov rais
	Bartlett-Han	Bartlett-Hann qhov rais
	Bartlett	Bartlett qhov rais
	BarthannWin	Hloov kho Bartlett-Hann qhov rais
	BohmanWin	BohmanWin qhov rais
	ChebWin	ChebWin windows
	FlattopWin	Flat top weighted qhov rais
	ParzenWin	ParzenWin qhov rais
	TaylorWin	TaylorWin qhov rais

	TukeyWin	TukeyWin (tapered cosine) qhov rais
Trigo	Tan	Tangent
	Cot	Cotangent
	Sec	Secant
	Csc	Cosecant
	Asin	Arc sib
	Acos	Arc cosine
	Atan	Arc tangent
	ACot	Arc cotangent
	CosH	Hyperbolic cosine
	CosInt	Integral cosine
	Coth	Hyperbolic cotangent
	Csch	Hyperbolic cosecant
	SecH	Hyperbolic secant
	SinH	Hyperbolic sine
	SinInt	Integral sine
	TanH	Hyperbolic tangent
	ACosH	Arc hyperbolic cosine
	ASECH	Arc hyperbolic secant
	ASinH	Arc hyperbolic sine
	ATanH	Arc hyperbolic tangent
	ACsch	Arc hyperbolic cosecant
	ACoth	Arc hyperbolic cotangent
Square 1	SquareDuty01	Square waveform nrog 1% dej num
	SquareDuty02	Square waveform nrog 2% dej num
	SquareDuty04	Square waveform nrog 4% dej num
	SquareDuty06	Square waveform nrog 6% dej num
	SquareDuty08	Square waveform nrog 8% dej num
	SquareDuty10	Square waveform nrog 10% dej num
	SquareDuty12	Square waveform nrog 12% dej num
	SquareDuty14	Square waveform nrog 14% dej num
	SquareDuty16	Square waveform nrog 16% dej num
	SquareDuty18	Square waveform nrog 18% dej num
	SquareDuty20	Square waveform nrog 20% dej num
	SquareDuty22	Square waveform nrog 22% dej num

	SquareDuty24	Square waveform nrog 24% dej num
	SquareDuty26	Square waveform nrog 26% dej num
	SquareDuty28	Square waveform nrog 28% dej num
	SquareDuty30	Square waveform nrog 30% dej num
	SquareDuty32	Square waveform nrog 32% dej num
	SquareDuty34	Square waveform nrog 34% dej num
	SquareDuty36	Square waveform nrog 36% dej num
	SquareDuty38	Square waveform nrog 38% dej num
	SquareDuty40	Square waveform nrog 40% dej num
	SquareDuty42	Square waveform nrog 42% dej num
	SquareDuty44	Square waveform nrog 44% dej num
	SquareDuty46	Square waveform nrog 46% dej num
	SquareDuty48	Square waveform nrog 48% dej num
	SquareDuty50	Square waveform nrog 50% dej num
	SquareDuty52	Square waveform nrog 52% dej num
	SquareDuty54	Square waveform nrog 54% dej num
	SquareDuty56	Square waveform nrog 56% dej num
	SquareDuty58	Square waveform nrog 58% dej num
	SquareDuty60	Square waveform nrog 60% dej num
	SquareDuty62	Square waveform nrog 62% dej num
	SquareDuty64	Square waveform nrog 64% dej num
	SquareDuty66	Square waveform nrog 66% dej num
	SquareDuty68	Square waveform nrog 68% dej num
Square 2	SquareDuty70	Square waveform nrog 70% dej num
	SquareDuty72	Square waveform nrog 72% dej num
	SquareDuty74	Square waveform nrog 74% dej num
	SquareDuty76	Square waveform nrog 76% dej num
	SquareDuty78	Square waveform nrog 78% dej num
	SquareDuty80	Square waveform nrog 80% dej num
	SquareDuty82	Square waveform nrog 82% dej num
	SquareDuty84	Square waveform nrog 84% dej num
	SquareDuty86	Square waveform nrog 86% dej num
	SquareDuty88	Square waveform nrog 88% dej num
	SquareDuty90	Square waveform nrog 90% dej num
	SquareDuty92	Square waveform nrog 92% dej num

	SquareDuty94	Square waveform nrog 94% dej num
	SquareDuty96	Square waveform nrog 96% dej num
	SquareDuty98	Square waveform nrog 98% dej num
	SquareDuty99	Square waveform nrog 99% dej num
Kho mob	EOG	Electro-oculogram
	EEG	Electroencephalogram
	EMG	Electromyogram
	Pulselogram	Pulselogram
	ReSpeed	Ceev nkhaus ntawm kev ua pa
	ECG 1	Electrocardiogram 1
	ECG 2	Electrocardiogram 2
	ECG 3	Electrocardiogram 3
	ECG 4	Electrocardiogram 4
	ECG 5	Electrocardiogram 5
	ECG 6	Electrocardiogram 6
	ECG 7	Electrocardiogram 7
	ECG 8	Electrocardiogram 8
	ECG 9	Electrocardiogram 9
	ECG 10	Electrocardiogram 10
	ECG 11	Electrocardiogram 11
	ECG 12	Electrocardiogram 12
	ECG 13	Electrocardiogram 13
	ECG 14	Electrocardiogram 14
	ECG 15	Electrocardiogram 15
	LFPulse	Waveform ntawm tsawg zaus mem tes electrotherapy
	Kaum 1	Waveform 1 ntawm cov paj hlwb stimulation electrotherapy
	Kaum 2	Waveform 2 ntawm cov paj hlwb stimulation electrotherapy
	Kaum 3	Waveform 3 ntawm cov paj hlwb stimulation electrotherapy
Mod	AM	Sectional sine AM signal
	FM	Sectional sine FM teeb liab
	PFM	Sectional mem tes FM teeb liab
	PM	Sectional sine PM teeb liab l
	PWM	Sectional PWM signal
Lim	Butterworth	Butterworth lim
Lim	Chebyshev 1	Chebyshev 1 lim

	Chebyshev 2	Chebyshev 2 lim
Demo	demo1_375pts	TureArb waveform 1 (375 pts)
	demo1_16kpts	TureArb waveform 1 (16384 pts)
	demo2_3kpts	TureArb waveform 2 (3000 pts)
	demo2_16kpts	TureArb waveform 2 (16384 pts)

2. Xaiv cov Waveform khaws cia
Xaiv Waveforms → Nplooj 1/2 → Arb → Arb Hom → Khaws Waveforms nkag mus rau hauv qab no interface, raws li qhia hauv daim duab 2-22.Tig lub pob qhov rooj lossis kov lub vijtsam xaiv qhov xav tau waveform. Tom qab ntawd xaiv Recall los yog nias lub pob khawm kom rov qab tau qhov sib thooj waveform.
2.8 Txhawm rau teeb tsa Harmonic Function
Lub SDG2000X tuaj yeem siv los ua lub tshuab hluav taws xob sib haum xeeb los ua kom muaj kev sib haum xeeb nrog kev txiav txim siab, amplitude thiab theem. Raws li Fourier hloov pauv, lub sij hawm ncua sij hawm sau waveform yog lub superposition ntawm sine waveforms raws li qhia hauv kab zauv hauv qab no: Feem ntau, cov khoom siv nrog f1 zaus hu ua fundamental waveform, f1 yog fundamental waveform zaus, A1 yog fundamental waveform. amplitude, thiab φ1 yog qhov tseem ceeb waveform theem.
Cov zaus ntawm lwm cov khoom (hu ua harmonics) yog tag nrho cov kev sib npaug ntawm cov qauv waveform. Cheebtsam uas nws cov zaus yog khib ntau ntawm qhov tseem ceeb waveform zaus hu ua khib harmonics thiab cov khoom uas nws zaus txawm ntau ntau ntawm lub hauv paus waveform zaus hu ua txawm harmonics.
Xovxwm Waveforms → Sine → Harmonic thiab xaiv "On", ces nias Harmonic Parameter nkag mus rau hauv qab no interface. Table 2-9 Menu Kev piav qhia ntawm Harmonic

Muaj nuj nqi zaub mov	Chaw	Kev piav qhia
Hom		Teem hom kev sib haum xeeb rau "kawg", "puas tau" lossis "tag nrho".
Kev txiav txim		Teeb qhov kev txiav txim ntawm lub harmonic.
Harmonic Ampl		Teeb lub amplitude ntawm lub harmonic.
Harmonic Phase		Teem lub theem ntawm kev sib haum xeeb.
Rov qab los		Rov qab mus rau sine parameters zaub mov.

Xaiv hom Harmonic
SDG2000X tuaj yeem tsim cov khoom sib txawv tsis zoo, puas muaj kev sib haum xeeb thiab cov neeg siv kev txiav txim siab ntawm kev sib haum xeeb.
Tom qab nkag mus rau cov ntawv qhia zaub mov harmonic, nias Hom xaiv hom kev sib haum xeeb uas xav tau.

Xovxwm Txawm , qhov ntsuas yuav tso tawm qhov tseem ceeb waveform thiab txawm tias harmonics.

Xovxwm khib , qhov ntsuas yuav tso tawm cov qauv waveform thiab khib harmonics.
Xovxwm Tag nrho , qhov ntsuas yuav tso tawm cov qauv waveform thiab tag nrho cov neeg siv kev txiav txim siab ntawm kev sib haum xeeb.

Txhawm rau teeb tsa Harmonic Order
Tom qab nkag mus rau hauv cov ntawv qhia zaub mov sib haum xeeb, nias Order , siv tus lej keyboard lossis pob qhov rooj nkag rau qhov xav tau.

Qhov ntau yog txwv los ntawm qhov tso zis ntau zaus ntawm qhov ntsuas thiab tam sim no qhov tseem ceeb waveform zaus.
Ntau yam: 2 txog qhov tso zis ntau zaus ntawm qhov ntsuas ÷ tam sim no qhov tseem ceeb waveform zaus
Qhov siab tshaj plaws yog 10.

Xaiv lub Harmonic Amptoj siab
Tom qab nkag mus rau cov ntawv qhia kev sib haum xeeb, nias Harmonic Ampl teem lub harmonic amplitude ntawm txhua qhov kev txiav txim.

Nias Order xaiv tus naj npawb ntawm cov kev sib raug zoo los teeb tsa.
Xovxwm Harmonic Ampl rau set amplitude ntawm lub harmonic xaiv. Siv cov xub xub thiab pob qhov rooj los hloov tus nqi. Los yog siv tus lej keyboard los nkag rau amplitude tus nqi thiab tom qab ntawd xaiv lub tsev xav tau los ntawm cov ntawv qhia pop-up. Cov chav nyob muaj yog Vpp, mVpp thiab dBc.

Xaiv qhov Harmonic Phase
Tom qab nkag mus rau hauv cov ntawv qhia kev sib haum xeeb, nias Harmonic Phase los teeb tsa cov theem kev sib haum xeeb ntawm txhua qhov kev txiav txim.

Nias Order xaiv tus naj npawb ntawm cov kev sib raug zoo los teeb tsa.
Nias Harmonic Phase los teeb tsa theem ntawm kev sib haum xeeb xaiv. Siv cov xub xub thiab pob qhov rooj los hloov tus nqi. Los yog siv tus lej keyboard los nkag rau theem tus nqi thiab tom qab ntawd xaiv chav tsev.

2.9 Txhawm rau teeb tsa Modulation Function
Siv cov Mod tus yuam sij los tsim modulated waveforms. SDG2000X tuaj yeem tsim AM, FM, ASK, FSK, PSK, PM, PWM thiab DSB-AM modulated waveforms. Modulating tsis sib txawv nrog cov hom ntawm cov modulation. Hauv AM, cov neeg siv tuaj yeem teeb tsa qhov chaw (sab hauv / sab nraud), qhov tob, hloov pauv zaus, hloov pauv waveform thiab cov cab kuj. Hauv DSB-AM, cov neeg siv tuaj yeem teeb tsa qhov chaw (sab hauv / sab nraud), kev hloov pauv zaus, hloov pauv waveform thiab cov cab kuj. Hauv FM, cov neeg siv tuaj yeem teeb tsa qhov chaw (sab hauv / sab nraud), hloov pauv zaus, qhov sib txawv zaus, hloov pauv waveform thiab cov cab kuj. Hauv PM, cov neeg siv tuaj yeem teeb tsa qhov chaw (sab hauv / sab nraud), theem sib txawv, hloov pauv zaus, hloov pauv waveform thiab cov cab kuj. Hauv ASK, cov neeg siv tuaj yeem teeb tsa qhov chaw (sab hauv / sab nraud), qhov tseem ceeb zaus thiab cov cab kuj. Hauv FSK, cov neeg siv tuaj yeem teeb tsa qhov chaw (sab hauv / sab nraud), qhov tseem ceeb zaus, hop zaus thiab cov cab kuj. Hauv PSK, cov neeg siv tuaj yeem teeb tsa qhov chaw (sab hauv / sab nraud), qhov tseem ceeb zaus, polarity thiab cov cab kuj. Hauv PWM, cov neeg siv tuaj yeem teeb tsa qhov chaw (sab hauv / sab nraud), kev hloov pauv zaus, qhov dav / lub luag haujlwm sib txawv, hloov pauv waveform thiab cov cab kuj.
Peb yuav qhia txog yuav ua li cas los teeb tsa cov kev txwv no hauv cov ntsiab lus raws li hom kev hloov pauv.
2.9.1 AM
Modulated waveform muaj ob ntu: tus cab kuj thiab modulating waveform. Hauv AM, lub amplitude ntawm tus cab kuj txawv nrog lub instantaneous voltage ntawm modulating waveform.
Xovxwm Mod → Hom → AM , qhov tsis sib xws ntawm AM modulation yog qhia hauv daim duab 2-24.Table 2-10 Menu Kev piav qhia ntawm AM Parameters

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Hom	AM	Ampkev hloov kho qhov siab
Qhov chaw	Sab hauv	Qhov chaw yog sab hauv
	Sab nraud	Qhov chaw yog sab nraud. Siv [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab.
	Channel	Modulation teeb liab xaiv lwm channel tso zis teeb liab.
AM Qhov tob		Teem lub modulation qhov tob.
Cov duab	Sine	Xaiv qhov modulating waveform.
	Square
	Daim duab peb sab
	UpRamp
	DnRamp
	Suab nrov
	Arb
AM Freq		Teem lub modulating waveform zaus. Ntau zaus: 1mHz ~ 1MHz (tsuas yog qhov chaw sab hauv).

Mus Xaiv Modulation Source
SDG2000X tuaj yeem lees txais cov teeb liab modulating los ntawm ib qho chaw sab hauv, sab nraud lossis lwm qhov kev hloov pauv channel. Xovxwm Mod → AM → Source xaiv "Internal", "External" los yog lwm channel modulation qhov chaw. Lub neej ntawd yog "Internal".

1. Internal Source
Thaum xaiv AM modulation qhov chaw, nias Shape los xaiv Sine, Square, Daim duab peb sab, UpRamp, DnRamp, Suab nrov lossis Arb li modulating waveform.

Square: 50% lub luag haujlwm voj voog
Daim duab peb sab: 50% symmetry
UpRamp: 100% symmetry
DnRamp: 0% symmetry
Arb: qhov arbitrary waveform xaiv ntawm cov channel tam sim no

Nco tseg:
Lub suab nrov tuaj yeem siv los ua kev hloov pauv waveform tab sis tsis tuaj yeem siv los ua tus cab kuj.
2. Sab nraud Source
Thaum xaiv qhov chaw sab nraud AM modulation, lub tshuab hluav taws xob lees txais sab nraud modulating teeb liab los ntawm [Aux In/Out] connector ntawm lub vaj huam sib luag tom qab. Lub sijhawm no, lub amplitude ntawm modulated waveform yog tswj los ntawm lub teeb liab theem siv rau lub connector. Rau example, yog qhov ntsuas qhov tob yog teem rau 100%, cov zis amplitude yuav yog qhov siab tshaj plaws thaum lub teeb liab modulating yog +6V thiab qhov tsawg kawg nkaus thaum lub teeb liab modulating yog -6V.
Kom Teem Modulation Depth
Modulation qhov tob qhia raws li ib tug percentage qhia cov amplitude variation degree. AM modulation qhov tob txawv ntawm 1% mus rau 120%. Nias AM Qhov tob los teeb qhov parameter.

Hauv 0% kev hloov pauv, cov zis amplitude yog ib nrab ntawm cov cab kuj amptoj siab.
Hauv 120% kev hloov pauv, cov zis amplitude yog tib yam nrog cov cab kuj amptoj siab.
Rau qhov chaw sab nraud, qhov tob ntawm AM yog tswj los ntawm voltage theem ntawm lub connector txuas nrog [Aux In/Out]. ± 6V sib haum rau 100% qhov tob.

Thaum xaiv qhov chaw modulation sab nraud, cov ntawv qhia zaub mov no tau muab zais.

Txhawm rau teeb tsa Modulation zaus
Thaum xaiv qhov kev hloov kho sab hauv, nias AM Freq kom pom qhov ntsuas qhov ntsuas, tom qab ntawd siv cov lej keyboard lossis xub yuam sij thiab pob qhov nkag rau qhov xav tau.

Modulation zaus ntawm 1mHz mus rau 1MHz.
Thaum xaiv qhov chaw modulation sab nraud, cov ntawv qhia zaub mov no tau muab zais.

2.9.2 DSB-AM
DSB-AM yog cov ntawv luv rau Ob-Sideband Suppressed Carrier - AmpLitude Modulation. Xovxwm Mod → Hom → DSB-AM . Cov kev txwv ntawm DSB-AM kev hloov pauv tau pom hauv daim duab 2-25.Table 2-1 1 Cov Ntawv Qhia Cov Lus Qhia ntawm DSB-AM Parameters

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Hom	DSB-AM	DSB Amplitude modulation.
Qhov chaw	Sab hauv	Qhov chaw yog sab hauv.
	Sab nraud	Qhov chaw yog sab nraud. Siv [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab.
	Channel	Modulation teeb liab xaiv lwm channel tso zis teeb liab
DSB Freq		Teem lub modulating waveform zaus. Ntau zaus: 1mHz ~ 1MHz (tsuas yog qhov chaw sab hauv).
Cov duab	Sine	Xaiv qhov modulating waveform.
	Square
	Daim duab peb sab
	UpRamp
	DnRamp
	Suab nrov
	Arb

Nco tseg: Cov cov txheej txheem ntawm kev teeb tsa cov kev txwv ntawm DSB-AM zoo ib yam li AM.
2.9.3fm ua
Modulated waveform muaj ob ntu: tus cab kuj thiab modulating waveform. Hauv FM, qhov zaus ntawm tus neeg nqa khoom sib txawv nrog qhov tam sim no voltage ntawm modulating waveform. Xovxwm Mod → Hom → FM , cov kev txwv ntawm FM modulation yog qhia hauv daim duab 2-26Table 2-12 Cov Ntawv Qhia Kev piav qhia ntawm FM Parameters

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Hom	FM	Zaus modulation
Qhov chaw	Sab hauv	Qhov chaw yog sab hauv
	Sab nraud	Qhov chaw yog sab nraud. Siv [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab.
	Channel	Modulation teeb liab xaiv lwm channel tso zis teeb liab
Freq Dev		Teeb qhov sib txawv zaus
Cov duab	Sine	Xaiv qhov modulating waveform.
	Square
	Daim duab peb sab
	UpRamp
	DnRamp
	Suab nrov
	Arb
FM zaus		Teem lub modulating waveform zaus. Ntau zaus 1mHz ~ 1MHz (qhov chaw sab hauv).

Kom Teem Frequency Deviation
Nias FM Dev txhawm rau txhawm rau ntsuas qhov ntsuas, thiab tom qab ntawd siv tus lej keyboard lossis xub yuam sij thiab pob qhov nkag mus rau qhov xav tau.

Qhov sib txawv yuav tsum sib npaug los yog tsawg tshaj li tus cab kuj zaus.
Qhov sib txawv ntawm qhov sib txawv thiab qhov sib txawv ntawm cov cab kuj yuav tsum sib npaug los yog tsawg dua qhov siab tshaj plaws ntawm cov khoom siv waveform uas tau xaiv.

Nco tseg:
Cov txheej txheem ntawm kev teeb tsa lwm qhov ntsuas ntawm FM zoo ib yam li AM.
2.9.4 XNUMXh
Modulated waveform muaj ob ntu: tus cab kuj thiab modulating waveform. Hauv PM, theem ntawm tus neeg nqa khoom sib txawv nrog lub sijhawm tam simtage theem ntawm modulating waveform. Xovxwm Mod → Hom → PM , qhov tsis zoo ntawm PM modulation yog qhia hauv daim duab 2-27.Table 2-13 Cov Ntawv Qhia piav qhia txog PM Parameters

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Hom	PM	Phase modulation
Qhov chaw	Sab hauv	Qhov chaw yog sab hauv
	Sab nraud	Qhov chaw yog sab nraud. Siv [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab.
	Channel	Modulation teeb liab xaiv lwm channel tso zis teeb liab
Phase Dev		Phase sib txawv ntawm 0 ° ~ 360 °.

Cov duab	Sine	Xaiv qhov modulating waveform.
	Square
	Daim duab peb sab
	UpRamp
	DnRamp
	Suab nrov
	Arb
PM Freq		Teem lub modulating waveform zaus. Ntau zaus: 1mHz ~ 1MHz.

Kom Teem Phase Deviation
Nias Phase Dev txhawm rau txhawm rau ntsuas qhov ntsuas, thiab tom qab ntawd siv tus lej keyboard lossis xub yuam sij thiab pob qhov nkag mus rau qhov xav tau.

Siv tus lej keyboard lossis xub yuam sij thiab pob qhov rooj nkag rau qhov xav tau.
Qhov ntau ntawm theem sib txawv yog los ntawm 0 ° txog 360 ° thiab tus nqi pib yog 100 °.

Nco tseg:
Cov txheej txheem ntawm kev teeb tsa lwm qhov tsis zoo ntawm PM zoo ib yam li AM.
2.9.5 FSK
FSK yog Frequency Shift Keying, qhov tso zis ntau zaus ntawm qhov hloov pauv ntawm ob lub sijhawm ua ntej (cov cab kuj zaus thiab qhov hop zaus lossis qee zaum hu ua cim zaus (1) thiab qhov chaw zaus (0)).
Xovxwm Mod → Hom → FSK , qhov tsis sib xws ntawm FSK kev hloov kho tau qhia hauv daim duab 2-28.Table 2-14 Cov Ntawv Qhia piav qhia ntawm FSK Parameters

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Hom	FSK	Zaus hloov keying modulation.
Qhov chaw	Sab hauv	Qhov chaw yog sab hauv.
Qhov chaw	Sab nraud	Qhov chaw yog sab nraud. Siv [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab.
Ntsiab Freq		Teem lub zaus ntawm qhov tso zis zaus hloov pauv ntawm cov cab kuj zaus thiab qhov hop zaus (tsuas yog kev hloov kho sab hauv): 1mHz ~ 1MHz.
Hop Freq		Teem lub hop zaus.

Txhawm rau teeb tsa qhov tseem ceeb
Thaum xaiv qhov kev hloov kho sab hauv, nias Qhov Tseem Ceeb Freq los teeb tsa tus nqi uas qhov tso zis zaus hloov ntawm "cov cab kuj zaus" thiab "hop zaus".

Siv tus lej keyboard lossis xub yuam sij thiab pob qhov rooj nkag rau qhov xav tau.

Cov zaus tseem ceeb ntawm 1mHz txog 1MHz.
Thaum xaiv qhov chaw modulation sab nraud, cov ntawv qhia zaub mov no tau muab zais.

Kom Teem Hop Frequency
Qhov ntau ntawm hop zaus nyob ntawm tus cab kuj zaus tam sim no xaiv. Nias Hop Freq los qhia txog qhov ntsuas, thiab tom qab ntawd siv tus lej keyboard lossis xub yuam sij thiab pob qhov rooj nkag rau qhov xav tau.

Zaus: 1uHz ~ 120MHz
Square: 1uHz ~ 25MHz
RampZaus: 1uHz ~ 1MHz
Zaus: 1uHz ~ 20MHz

Nco tseg:
Cov txheej txheem ntawm kev teeb tsa lwm qhov ntawm FSK zoo ib yam li AM. Tsis tas li ntawd, sab nraud modulating teeb liab ntawm FSK yuav tsum yog Square uas ua raws li CMOS qib specification.
2.9.6 UAS
Thaum siv NUG (Amplitude Shift Keying), tus cab kuj zaus thiab qhov tseem ceeb zaus yuav tsum tau teeb tsa. Qhov tseem ceeb zaus yog qhov hloov pauv ntawm modulated waveform amptoj siab.
Xovxwm Mod → Hom → NUG , cov kev txwv ntawm ASK kev hloov pauv tau qhia hauv daim duab 2-29.Table 2-15 Cov Ntawv Qhia piav qhia ntawm ASK Parameters

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Hom	NUG	Amplitude hloov keying modulation.
Qhov chaw	Sab hauv	Qhov chaw yog sab hauv.
Qhov chaw	Sab nraud	Qhov chaw yog sab nraud. Siv [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab.
Ntsiab Freq		Teem lub zaus ntawm qhov tso zis amplitude hloov ntawm cov cab kuj ampLitude thiab xoom (tsuas yog kev hloov kho sab hauv): 1mHz ~ 1MHz.

Nco tseg:
Cov txheej txheem rau kev teeb tsa qhov ntsuas ntawm ASK zoo ib yam li AM. Tsis tas li ntawd, sab nraud modulating teeb liab ntawm ASK yuav tsum yog Square uas ua raws li CMOS qib specification.
2.9.7 TSI
Thaum siv PSK (Phase Shift Keying), teeb tsa lub tshuab hluav taws xob rau "ua haujlwm" nws cov zis theem ntawm ob theem preset qhov tseem ceeb (theem nqa khoom thiab theem hloov pauv). Lub default modulating theem yog 180 °.
Xovxwm Mod → Hom → PSK , qhov tsis muaj PSK kev hloov pauv tau qhia hauv daim duab 2-30. Table 2-16 Cov Lus Qhia piav qhia ntawm PSK Parameters

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Hom	PSK	Phase hloov keying modulation.
Qhov chaw	Sab hauv	Qhov chaw yog sab hauv.
Qhov chaw	Sab nraud	Qhov chaw yog sab nraud. Siv [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab.
Ntsiab Freq		Teem lub zaus ntawm qhov tso zis theem hloov ntawm cov cab kuj theem thiab 180 ° (sab hauv kev hloov pauv nkaus xwb): 1mHz ~ 1MHz.
Polarity	Qhov zoo	Teem lub modulating polarity.
Polarity	Tsis zoo	Teem lub modulating polarity.

Nco tseg:
Cov txheej txheem ntawm kev teeb tsa qhov ntsuas ntawm PSK zoo ib yam li AM. Tsis tas li ntawd, sab nraud modulating teeb liab ntawm PSK yuav tsum yog Square uas ua raws li CMOS qib specification.
2.9.8 PWM
Hauv PWM (Pulse Width Modulation), lub mem tes dav ntawm lub mem tes sib txawv nrog qhov tam sim no vol.tage ntawm modulating waveform. Tus neeg nqa khoom tuaj yeem tsuas yog mem tes.
Xovxwm Waveforms → Pulse → Mod , qhov tsis muaj ntawm PWM kev hloov pauv tau qhia hauv daim duab 2-31

Table 2-17 Menu Explanations of PWM Parameters

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Hom	PWM	Pulse width modulation. Tus cab kuj yog mem tes.
Qhov chaw	Sab hauv	Qhov chaw yog sab hauv.
	Sab nraud	Qhov chaw yog sab nraud. Siv [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab.
	Channel	Modulation teeb liab xaiv lwm channel tso zis teeb liab
Dav Dev		Teeb qhov dav sib txawv.
Duty Dev		Teeb lub luag haujlwm sib txawv.
Cov duab	Sine	Xaiv qhov modulating waveform.
	Square
	Daim duab peb sab
	UpRamp
	DnRamp
	Suab nrov
	Arb
PWM Freq		Teem lub modulating waveform zaus. Ntau zaus: 1mHz ~ 1MHz (tsuas yog qhov chaw sab hauv).

Kom Teem Pulse Dav/Duty Deviation
Width Deviation sawv cev rau qhov kev hloov pauv ntawm modulated waveform pulse width txheeb ze rau qhov qub mem tes dav. Nias Dav Dev txhawm rau txhawm rau ntsuas qhov ntsuas, thiab siv tus lej keyboard lossis xub yuam sij thiab lub pob khawm kom nkag mus rau qhov xav tau, raws li qhia hauv daim duab 2-32.

Qhov dav sib txawv tsis tuaj yeem tshaj qhov dav pulse tam sim no.
Qhov dav sib txawv yog txwv los ntawm qhov tsawg kawg nkaus pulse dav thiab tam sim no ntug lub sij hawm teem.

Lub luag haujlwm Deviation sawv cev rau qhov kev hloov pauv (%) ntawm lub luag haujlwm hloov pauv hloov pauv piv rau lub luag haujlwm qub. Nias Lub Luag Haujlwm Dev txhawm rau txhawm rau ntsuas qhov ntsuas, thiab tom qab ntawd siv tus lej keyboard lossis xub yuam sij thiab lub pob kom nkag mus rau qhov xav tau, raws li qhia hauv daim duab 2-33.

Lub luag hauj lwm sib txawv tsis tuaj yeem tshaj lub voj voog lub luag hauj lwm mem tes tam sim no.

Lub luag haujlwm sib txawv yog txwv los ntawm qhov tsawg kawg nkaus lub luag haujlwm voj voog thiab lub sijhawm tam sim no ntawm ntug kev teeb tsa.
Lub luag haujlwm sib txawv thiab qhov dav sib txawv yog sib txheeb. Thaum ib qho kev hloov pauv, lwm qhov yuav raug hloov pauv.

Nco tseg:
Cov txheej txheem ntawm kev teeb tsa lwm qhov tsis zoo ntawm PWM zoo ib yam li AM.
2.10 Txhawm rau teeb tsa Sweep Function
Hauv hom cheb, lub tshuab hluav taws xob cov kauj ruam los ntawm qhov pib zaus mus rau qhov nres zaus hauv lub sijhawm cheb tau teev tseg los ntawm tus neeg siv. Cov waveforms uas txhawb cheb muaj xws li sine, square, ramp thiab arbitrary.
Nias Sweep key nkag mus rau cov ntawv qhia zaub mov nram qab no. Teem lub waveform parameters los ntawm kev siv cov ntawv qhia ua haujlwm. Table 2-18 Phau Ntawv Qhia Txog Sweep (Nplooj 1/2)

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Siv sijhawm		Teem lub sij hawm ncua sij hawm ntawm lub cheb nyob rau hauv uas lub zaus hloov ntawm qhov pib zaus kom nres zaus.
Pib Freq Mid Freq		Teem qhov pib zaus ntawm cheb; Teem lub nruab nrab zaus ntawm cheb.
Nres Freq Freq Span		Teem lub sijhawm nres ntawm qhov cheb; Teem lub zaus ncua ntawm cheb.
Qhov chaw	Sab hauv	Xaiv qhov chaw sab hauv raws li qhov tshwm sim.
	Sab nraud	Xaiv qhov chaw sab nraud los ua qhov tshwm sim. Siv [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab.
	Phau ntawv	Tig lub cheb los ntawm phau ntawv.
Trig tawm	Tawm	Disable trigger tawm.
Trig tawm	On	Enable ua kom tawm.
Nplooj 1/2		Nkag mus rau nplooj ntawv tom ntej.

Table 2-19 Phau Ntawv Qhia Txog Sweep (Nplooj 2/2)

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Hom	Tawm	Teem lub cheb nrog linear profile.
Hom	Log	Teem lub cheb nrog logarithmic profile.
Kev taw qhia	Up	Sweep upward.
Kev taw qhia	nqes	cheb downward.
Idle Freq	Pib Freq	Tom qab cheb cov zis, qhov zaus nyob ntawm qhov pib zaus
	Nres Freq	Tom qab cheb cov zis, qhov zaus nyob ntawm qhov nres zaus
	Pib Point	Tom qab cheb cov zis, qhov zaus nyob ntawm qhov pib Point
Nplooj 2/2		Rov qab mus rau nplooj ntawv dhau los.

Sweep Zaus
Siv pib freq thiab nres freq los yog qhov chaw freq thiab freq ncua sij hawm los teeb qhov ntau ntawm cov zaus cheb.
Nias tus yuam sij dua los hloov ntawm ob hom cheb ntau hom.
Pib zaus thiab nres zaus
Start Frequency thiab Stop Frequency yog qhov qis thiab sab sauv txwv ntawm zaus rau cheb. Pib zaus ≤ Nres zaus.

Xaiv Kev taw qhia → Up , lub tshuab hluav taws xob yuav cheb los ntawm Pib zaus kom nres zaus.
Xaiv Kev taw qhia → Down , lub tshuab hluav taws xob yuav cheb los ntawm Nres zaus mus rau Pib zaus.

Center Frequency thiab zaus Span
Center zaus = (| Pib zaus + Nres zaus |)/2
Zaus Span = Nres zaus – Pib zaus
Sweep Hom
SDG2000X muab "Linear" thiab "Log" cheb profiles thiab lub neej ntawd yog "Linear".
Linear Sweep
Nyob rau hauv linear cheb, qhov tso zis zaus ntawm qhov ntsuas nws txawv linearly nyob rau hauv txoj kev ntawm "ntau tus Hertz ib ob". Xaiv Sweep → Nplooj 1/2 → Hom → Linear , muaj ib txoj kab ncaj nraim tso tawm ntawm lub waveform ntawm qhov screen, qhia tias cov zis zaus sib txawv linearly.Log Sweep
Nyob rau hauv lub log cheb, qhov tso zis zaus ntawm qhov ntsuas nws txawv nyob rau hauv ib tug logarithmic zam, uas yog, cov zis zaus hloov nyob rau hauv txoj kev ntawm "xyoo caum ib ob". Xaiv Sweep → Nplooj 1/2 → Hom → Log , muaj ib tug exponential muaj nuj nqi nkhaus tso tawm nyob rau hauv lub waveform ntawm qhov screen, qhia tias cov zis zaus hloov nyob rau hauv ib tug logarithmic hom.

Sweep Trigger Source
Lub cheb trigger qhov chaw tuaj yeem yog sab hauv, sab nraud lossis phau ntawv. Lub tshuab hluav taws xob yuav tsim cov khoom tawm cheb thaum lub teeb liab tau txais thiab tom qab ntawd tos rau qhov txiaj ntsig tom ntej.

Internal Trigger
Xaiv Qhov chaw → Internal , lub tshuab hluav taws xob outputs nruam cheb waveform thaum sab hauv trigger raug xaiv. Lub neej ntawd yog "Internal". Xaiv Trig Out → On , [Aux In/Out] connector ntawm lub vaj huam sib luag tom qab yuav tso tawm cov teeb liab tshwm sim.

Sab nraud Trigger
Xaiv Spebce → External , lub tshuab hluav taws xob lees txais lub cim teeb liab nkag los ntawm [Aux In/Out] connector ntawm lub vaj huam sib luag tom qab thaum xaiv sab nraud. Kev cheb yuav raug tsim tawm thaum lub connector tau txais CMOS mem tes nrog cov polarity teev. Txhawm rau teeb tsa CMOS pulse polarity, xaiv Edge los xaiv "Up" lossis "Down".
Phau ntawv txhais
Xaiv Source → Phau ntawv , ib qho cheb yuav raug tsim los ntawm cov channel sib raug thaum lub Trigger softkey raug nias thaum phau ntawv txhais lus raug xaiv. Xaiv Trig Out → On , [Aux In/Out] connector ntawm lub vaj huam sib luag tom qab yuav tso tawm cov teeb liab tshwm sim.

2.11 Txhawm rau teeb tsa tawg ua haujlwm
Kev ua haujlwm tawg tuaj yeem tsim muaj ntau yam waveforms hauv hom no. Lub sij hawm tawg tuaj yeem kav ntev npaum li cas ntawm lub voj voog waveform (N-Cycle hom), lossis thaum siv cov teeb liab sab nraud (Gated hom) siv. Txhua yam waveform (tshwj tsis yog DC) tuaj yeem siv los ua tus nqa khoom, tab sis lub suab nrov tsuas yog siv tau hauv Gated hom.
Hom tawg
SDG2000X muab peb hom tawg xws li N-Cycle, Infinite thiab Gated. Lub neej ntawd yog N-Cycle.
Table 2-20 Kev sib raug zoo ntawm cov tawg hom, ua rau qhov chaw thiab cov cab kuj

Hom tawg	Nthuav qhov chaw	Tus neeg nqa khoom
N-Cycle	Internal/External/Manual	Sib, Square, Ramp, Pulse, Arbitrary.
Tsis kawg	Sab nraud / Phau ntawv	Sib, Square, Ramp, Pulse, Arbitrary.
Gated	Sab Hauv / Sab Nraud	Sib, Square, Ramp, Pulse, Suab nrov, Arbitrary.

N-Cycle
Nyob rau hauv hom N-Cycle, lub tshuab hluav taws xob yuav tso tawm waveform nrog rau tus naj npawb ntawm cov voj voog tom qab tau txais cov teeb liab tshwm sim. Waveforms uas txhawb N-Cycle tawg muaj xws li sine, square, ramp, mem tes thiab arbitrary.
Xovxwm Ncua → Ncua sij hawm → Cycles , thiab siv tus lej keyboard lossis xub yuam sij thiab pob qhov rooj nkag mus rau qhov xav tau mus. Teem lub waveform tsis los ntawm kev siv cov ntawv qhia ua haujlwm, raws li pom hauv daim duab 2-38 thiab daim duab 2-39.Table 2-21 Menu Kev piav qhia ntawm N-Cycle Burst (Page 1/2)

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Ncis		Siv N-Cycle hom.
Cycles Infinite		Teem tus naj npawb ntawm qhov tawg hauv N-Cycle. Teem tus naj npawb ntawm qhov tawg hauv N-Cycle kom tsis kawg.
Pib Theem		Teem lub sijhawm pib ntawm qhov tawg.
Lub Sijhawm tawg		Teem lub sijhawm tawg.
Qhov chaw	Sab hauv	Xaiv qhov chaw sab hauv raws li qhov tshwm sim.
	Sab nraud	Xaiv qhov chaw sab nraud los ua qhov tshwm sim. Siv [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab.
	Phau ntawv	Ua kom tawg los ntawm phau ntawv.
Nplooj 1/2		Nkag mus rau nplooj ntawv tom ntej.

Table 2-22 Menu Kev piav qhia ntawm N-Cycle Burst (Page2/2)

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
ncua		Teem lub sijhawm ncua ua ntej qhov tawg pib.
Trig tawm	Tawm	Disable trigger tawm.
Trig tawm	On	Enable ua kom tawm.
Cov Counter		Teem tus naj npawb ntawm cov voj voog tawg nyob rau hauv qhov kev cuam tshuam yog sab nraud thiab phau ntawv
Nplooj 2/2		Rov qab mus rau nplooj ntawv dhau los.

Tsis kawg
Nyob rau hauv hom infinite, lub voj voog tus lej ntawm lub waveform yog teem raws li tus nqi infinite. Lub tshuab hluav taws xob outputs ib tug nruam waveform tom qab tau txais cov teeb liab trigger. Waveforms uas txhawb hom infinite muaj xws li sine, square, ramp, mem tes thiab arbitrary.
Xovxwm Tawg → NCycle → Infinite , thiab teeb qhov chaw ua rau "sab nraud" lossis "phau ntawv". Lub vijtsam yuav tso saib lub voj voog tawg tsis kawg, raws li pom hauv daim duab 2-40 Infinite Burst Interface Daim duab 2-40.Gated
Nyob rau hauv hom gated, lub tshuab hluav taws xob tswj cov waveform tso zis raws li lub rooj vag teeb liab theem. Thaum lub teeb liab gated yog "muaj tseeb", lub tshuab hluav taws xob tso tawm ib qho kev sib txuas tsis tu ncua. Thaum lub teeb liab gated yog "tsis tseeb", lub tshuab hluav taws xob ua ntej ua tiav cov zis ntawm lub sijhawm tam sim no thiab tom qab ntawd nres. Waveforms uas txhawb gated tawg muaj xws li sine, square, ramp, mem tes, suab nrov thiab arbitrary.
Xovxwm Poob → Gated , nkag mus rau hauv qab no interface. Table 2-23 Menu Piav Qhia ntawm Gated Burst

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Gated		Siv lub qhov rooj kaw.
Polarity	Qhov zoo	Teem lub polarity rau lub teeb liab gated.
Polarity	Tsis zoo	Teem lub polarity rau lub teeb liab gated.
Pib Theem		Teem lub sijhawm pib ntawm qhov tawg.
Lub Sijhawm tawg		Teem lub sijhawm tawg.
Qhov chaw	Sab hauv	Xaiv qhov chaw sab hauv raws li qhov tshwm sim.
Qhov chaw	Sab nraud	Xaiv qhov chaw sab nraud los ua qhov tshwm sim. Siv [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab.

Pib Theem
Txhais qhov pib taw tes nyob rau hauv ib tug waveform. Cov theem sib txawv ntawm 0 ° mus rau 360 °, thiab qhov chaw pib yog 0 °.
Rau qhov Arbitrary Waveform, 0 ° yog thawj qhov taw tes waveform.
Lub Sijhawm tawg
Lub Sijhawm tawg yog muaj thaum lub hauv paus pib yog sab hauv thiab Phau Ntawv Qhia. Nws txhais tau tias yog lub sijhawm los ntawm qhov pib tawg mus rau qhov pib ntawm qhov tom ntej. Xaiv Lub Sijhawm Hlawv thiab siv tus lej keyboard lossis xub yuam sij thiab pob qhov nkag mus rau qhov xav tau.

Lub Sijhawm tawg ≥ 0.99μs + lub sijhawm thauj khoom × tawg tus lej
Yog tias lub sijhawm tawg tam sim no luv dhau lawm, lub tshuab hluav taws xob yuav nce tus nqi no cia li tso cai tso tawm cov lej teev cov voj voog.

Cycles/Infinite
Teem tus naj npawb ntawm waveform voj voog hauv N-Cycle (1 txog 50,000 lossis Infinite).
Yog tias Infinite raug xaiv, ces qhov nruam waveform yuav raug tsim ib zaug ib qho tshwm sim.
ncua
Teem lub sij hawm ncua nruab nrab ntawm qhov kev tawm tswv yim thiab pib ntawm N-Cycle tawg.
Burst Trigger Source
Qhov tshwm sim tawg tuaj yeem yog sab hauv, sab nraud lossis phau ntawv. Lub tshuab hluav taws xob yuav ua kom tawg
tso zis thaum lub teeb liab tau txais thiab tom qab ntawd tos rau qhov tshwm sim tom ntej.

Internal Trigger
Xaiv Qhov chaw → Internal , lub tshuab hluav taws xob outputs nruam tawg waveform thaum sab hauv trigger raug xaiv. Xaiv Trig Out li "Up" lossis "Down", [Aux In/Out] connector ntawm lub vaj huam sib luag tom qab yuav tso tawm lub teeb liab nrog cov ntug.
Sab nraud Trigger
Xaiv Source → Sab nraud , lub tshuab hluav taws xob lees txais lub cim teeb liab nkag los ntawm [Aux In/Out] connector ntawm lub vaj huam sib luag tom qab thaum xaiv sab nraud. Kev tawg yuav raug tsim tawm thaum lub connector tau txais CMOS mem tes nrog cov polarity teev. Txhawm rau teeb tsa CMOS pulse polarity, xaiv Edge los xaiv "Up" lossis "Down".
Phau ntawv txhais
Xaiv Source → Phau ntawv , qhov tawg yuav raug tsim los ntawm cov channel sib raug thaum lub Trigger softkey raug nias thaum phau ntawv txhais lus raug xaiv.

2.12 Khaws thiab Rov Qab
SDG2000X tuaj yeem khaws cov ntsuas ntsuas tam sim no thiab cov neeg siv cov ntaub ntawv tsis txaus ntseeg nyob rau hauv lub cim xeeb sab hauv lossis sab nraud thiab nco qab lawv thaum xav tau. Xovxwm Khw/Rau nkag mus rau hauv qab no interface.Table 2-24 Phau Ntawv Qhia Txog Txuag thiab Rov Qab

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
File Hom	Xeev	Kev teeb tsa ntawm lub tshuab hluav taws xob;
File Hom	Cov ntaub ntawv	Arbitrary waveform file
Saib		View daim ntawv teev npe tam sim no.
Txuag		Txuag lub waveform mus rau txoj kev teev tseg.
Nco qab		Nco qab lub waveform los yog teeb tsa cov ntaub ntawv nyob rau hauv qhov chaw tshwj xeeb ntawm lub cim xeeb.
Rho tawm		Rho tawm cov xaiv file.
Nplooj 1/2		Nkag mus rau nplooj ntawv tom ntej.

Table 2-25 Phau Ntawv Qhia Txog Txuag thiab Rov Qab

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Luam		Luam qhov xaiv file.
Muab tshuaj txhuam		Paste qhov xaiv file.
Tso tseg		Tawm hauv Khw / Rov qab interface.
Nplooj 2/2		Rov qab mus rau nplooj ntawv dhau los.

2.12.1 Cia System
SDG2000X muab lub cim xeeb sab hauv uas tsis yog-volatile (C Disk) thiab USB Host interface rau lub cim xeeb sab nraud.

Hauv zos (C:)
Cov neeg siv tuaj yeem khaws cov ntsuas lub xeev thiab cov ntawv tsis txaus ntseeg files rau C Disk.

USB ntaus ntawv (0:)
Nws muaj USB Host interface nyob rau sab laug ntawm lub vaj huam sib luag pem hauv ntej uas tso cai rau cov neeg siv khaws cia / nco qab cov duab los yog hloov kho cov firmware version los ntawm U-Disk. Thaum lub tshuab hluav taws xob pom lub cuab yeej USB cia, lub vijtsam yuav qhia tsab ntawv tsav "USB Device (0:)" thiab tso cov lus ceeb toom "USB ntaus ntawv txuas nrog.", raws li pom hauv daim duab 2-44. Tom qab tshem tawm U-Disk, lub vijtsam yuav tso tawm cov lus ceeb toom "USB ntaus ntawv tshem tawm." Thiab "USB Device (0:)" hauv cov ntawv qhia zaub mov yuav ploj mus.

Nco tseg:
SDG2000X tsuas tuaj yeem txheeb xyuas files uas filecov npe muaj cov tsiaj ntawv Askiv, lej thiab underscore. Yog tias siv lwm cov cim, lub npe yuav raug tso tawm hauv lub khw thiab nco qab qhov cuam tshuam txawv txav.
Saib

Siv lub pob khawm hloov ntawm cov npe lossis nyem qhov chaw sib txuas ntawm qhov screen xaiv Local (C:) lossis USB Device (0:). Xaiv Browse, nias lub pob los yog nyem rau ntawm lub nplaub tshev xaiv los qhib cov npe tam sim no.

Siv lub pob khawm hloov ntawm cov ntawv tais ceev tseg thiab files nyob rau hauv daim ntawv teev npe tam sim no. Xaiv Xauj , nias lub pob khawm lossis nyem rau ntawm cov ntawv tais ceev tseg qhib lub subdirectory. Xaiv , tom qab ntawd xaiv Brower lossis nias lub pob khawm kom rov qab mus rau qib siab sau npe.

2.12.2 File Hom
Xaiv Khw / Rov qab → File Hom los xaiv qhov xav tau file hom. Muaj file hom yog Xeev File thiab Data File.
Xeev File
Khaws lub ntsuas ntsuas hauv lub cim xeeb sab hauv lossis sab nraud hauv "*.xml" hom. Lub xeev file khaws cia suav nrog waveform parameters thiab modulation, cheb, tawg tsis tau ntawm ob txoj kab thiab cov khoom siv hluav taws xob.
Cov ntaub ntawv File
SDG2000X tuaj yeem rov qab tau cov ntaub ntawv files hauv "*.csv" lossis "*.dat" hom ntawv los ntawm lub cim xeeb sab nraud thiab hloov mus rau hauv "*.bin" hom ntawv ces khaws cia rau hauv lub cim xeeb sab hauv. Thaum nws ua tiav, lub tshuab hluav taws xob yuav nkag mus rau qhov arbitrary waveform interface tau txais.
Tsis tas li ntawd, cov neeg siv tuaj yeem hloov kho qhov tsis txaus ntseeg waveforms nrog PC software - EasyWave, rub lawv mus rau lub cim xeeb sab hauv los ntawm cov chaw taws teeb interface thiab khaws lawv (hauv "*.bin" hom) hauv lub cim xeeb sab hauv.
2.12.3 File Kev ua haujlwm
Kom Txuag Instrument State
Cov neeg siv tuaj yeem khaws cov ntsuas tam sim no hauv kev nco sab hauv thiab sab nraud. Qhov chaw cia yuav txuag cov haujlwm uas tau xaiv (xws li cov qauv waveform tsis yooj yim, kev hloov pauv tsis tau thiab lwm qhov chaw siv hluav taws xob siv.)
Txhawm rau txuag lub xeev ntsuas, cov txheej txheem tau muab raws li hauv qab no:

Xaiv qhov file hom khaws cia.
Xovxwm Khw / Rov qab → File Hom → Xeev , thiab xaiv lub xeev raws li hom cia.
Xaiv qhov chaw ntawm lub file.
Xaiv qhov chaw xav tau los ntawm kev tig lub pob qhov rooj lossis nyem qhov chaw sib thooj ntawm lub vijtsam kov.
Lub npe file.
Nyem Txuag , nkag mus rau hauv qab no interface.

Table 2-26 Menu Kev piav qhia ntawm File Cia

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Up		Cursor upward los xaiv.
nqes		Cursor downward los xaiv.
Xaiv		Xaiv tus cim tam sim no.
Rho tawm		Tshem tawm cov cim tam sim no.
Txuag		Khaws lub file nrog lub npe tam sim no.
Tso tseg		Rov qab mus rau lub khw / Recall interface.

Xaiv tus cwj pwm
Cov neeg siv tuaj yeem xaiv cov cim xav tau los ntawm cov keyboard virtual los ntawm kev siv lub pob qhov rooj lossis Up thiab Down menus. Los yog kov qhov chaw ntawm tus cwj pwm ntawm qhov screen ncaj qha. Ces xaiv Xaiv los tso saib cov cim xaiv nyob rau hauv lub filenpe area.
Rho tawm tus cwj pwm
Siv cov ntiv tes laug thiab sab xis txav tus cursor hauv qhov file npe. Tom qab ntawd xaiv Delete los rho tawm cov cim coj.

4. Txuag cov file.
Tom qab ua tiav inputting filenpe, nias Txuag. Lub tshuab hluav taws xob yuav txuag tau qhov file nyob rau hauv lub tam sim no xaiv directory nrog cov teev filenpe.
Mus Rov Qab Xeev File los yog Data File
Txhawm rau rov qab cov ntaub ntawv ntsuas lub xeev lossis cov ntaub ntawv tsis txaus ntseeg, cov txheej txheem yog raws li hauv qab no:

Xaiv qhov file hom.
Xovxwm Khw / Rov qab → File Hom , thiab xaiv lub xeev lossis cov ntaub ntawv raws li hom cia.
Xaiv qhov file kom nco qab.
Tig lub pob qhov rooj los yog nyem qhov screen kov los xaiv qhov file koj xav rov qab los.
Nco qab lub file.
Xaiv Recall , nias lub pob khawm lossis nyem qhov chaw ntawm lub file ntawm qhov screen, lub tshuab hluav taws xob yuav nco qab cov xaiv file thiab tso saib cov lus ceeb toom thaum lub file tau nyeem tiav.

Mus Rho Tawm File
Txhawm rau rho tawm cov ntaub ntawv ntsuas lub xeev lossis cov ntaub ntawv arbitrary waveform, cov txheej txheem yog raws li hauv qab no:

Xaiv qhov file.
Tig lub pob qhov rooj los yog nyem qhov screen kov los xaiv qhov file koj xav rho tawm.
Rho tawm cov file.
Xaiv Rho tawm, lub tshuab hluav taws xob yuav tso tawm cov lus ceeb toom 'Delete the file?' Tom qab ntawd nias Txais , lub tshuab hluav taws xob yuav tshem tawm cov kev xaiv tam sim no file.

Luam thiab Paste File
SDG2000X txhawb nqa sab hauv thiab sab nraud cia rau luam files sib. Rau example, luam ib tug arbitrary yoj file Hauv U-disk rau qhov ntsuas, cov txheej txheem yog raws li hauv qab no:

Xaiv qhov file hom.
Xovxwm Khw / Rov qab → File Ntause , thiab xaiv "Cov ntaub ntawv" raws li hom cia.
Xaiv qhov file kom tau theej.
Tig lub pob qhov rooj xaiv USB Device (0:) thiab nias lub pob qhib nws cov npe. Tom qab ntawd tig lub pob qhov rooj los xaiv qhov file koj xav luam thiab nias Page 1/2 → Copy .
Muab tshuaj txhuam rau file.
Tig lub pob qhov rooj los xaiv Local (C:) thiab nias lub pob qhib nws cov npe. Ces nias Paste.

2.13 Txhawm rau teeb tsa kev siv hluav taws xob
Nrog rau kev siv hluav taws xob muaj nuj nqi, tus neeg siv tuaj yeem teeb tsa qhov tsis sib xws ntawm lub tshuab hluav taws xob xws li Sync, Interface, Kev Teeb Meem, Kev Ntsuas Tus Kheej thiab Zaus Counter, thiab lwm yam. Kev siv hluav taws xob kom nkag mus rau hauv cov ntawv qhia hluav taws xob, raws li qhia hauv daim duab 2-47 Daim duab 2-48 thiab daim duab 2-49. Table 2-27 Phau Ntawv Qhia Txog Kev Siv Hluav Taws Xob (Page 1/3)

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Qhov system		Teem lub system configuration.
Test/Cal		Kuaj thiab calibrate lub ntsuas.
Cov txee		Kev teeb tsa zaus.
Kev teeb tsa tso zis		Teem cov zis tsis tau ntawm CH1 thiab CH2.
CH Copy Coupling		Teem tus khiav, channel coupling los yog channel luam muaj nuj nqi.
Nplooj 1/3		Nkag mus rau nplooj ntawv tom ntej.

Table 2-28 Phau Ntawv Qhia Txog Kev Siv Hluav Taws Xob (Page 2/3)

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Interface		Teem lub parameter ntawm tej thaj chaw deb interfaces.
Sync		Teem lub sync tso zis.
moos	Sab hauv	Xaiv qhov system moos qhov chaw.
moos	Sab nraud	Xaiv qhov system moos qhov chaw.
Pab		View cov ntaub ntawv pab.
OverVoltage Kev Tiv Thaiv		Qhib / tawm lub overvoltage kev tiv thaiv muaj nuj nqi.
Nplooj 2/3		Nkag mus rau nplooj ntawv tom ntej.

Table 2-29 Phau Ntawv Qhia Txog Kev Siv Hluav Taws Xob (Page 3/3)

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Multi-Device Sync		Nthuav ntau yam khoom siv ob-channel rau plaub lossis ntau dua
Nplooj 3/3		Rov qab mus rau nplooj ntawv dhau los.

2.13.1 System Settings
Xovxwm Utility → System , nkag mus rau hauv qab no interface.Table 2-30 Cov Ntawv Qhia piav qhia txog Kev Teeb Meem (Nplooj 1/2)

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Tus lej format		Teem tus naj npawb hom.
Lus	Lus Askiv	Teem cov lus.
Lus	Suav	Teem cov lus.
Hwj chim On	Default	Txhua qhov teeb tsa rov qab mus rau qhov qub thaum lub hwj chim qhib;
	Kawg	Tag nrho cov kev teeb tsa rov qab mus rau qhov chaw ntawm lub hwj chim kawg.
	Cov neeg siv	Load configuration nyob rau hauv tus neeg siv teev configuration file ntawm lub zog
Teem rau Default		Teem tag nrho cov chaw rau lub neej ntawd.
Beeper	On	Qhib lub beeper.

	Tawm	Kaw lub beeper.
Nplooj 1/2		Nkag mus rau nplooj ntawv tom ntej.

Table 2-31 Cov Ntawv Qhia piav qhia txog Kev Teeb Meem (Nplooj 2/2)

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
ScrnSvr	1 min	Qhib lossis kaw qhov screen saver.
	5 min
	15 min
	30 min
	1 teev
	2 teev
	5 teev
	Tawm	Disable qhov screen saver.
System Info		View cov ntaub ntawv system
Firmware Update		Hloov kho cov firmware los ntawm U-disk.
Pab		Cov ntsiab lus ntawm tus neeg siv phau ntawv
UI Style	Classical	Raws li pom hauv daim duab 2-52
UI Style	Ib txwm	Raws li pom hauv daim duab 2-53
Nplooj 2/2		Rov qab mus rau nplooj ntawv dhau los.

1. Tus lej Format
Xovxwm Utility → System → Number Format , nkag mus rau hauv qab no interface.Table 2-32 Ntawv qhia zaub mov piav qhia txog kev teeb tsa tus lej hom

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Taw tes	.	Siv dot los sawv cev tus lej lej;
Taw tes	,	Siv comma los sawv cev tus lej lej.
Separator	On	Ua kom lub Separator;
	Tawm	Kaw lub Separator;
	Qhov chaw	Siv Space ua tus cais.
Ua tiav		Txuag cov chaw tam sim no thiab rov qab mus rau System menu.

Raws li kev xaiv sib txawv ntawm tus lej lej thiab tus cais, cov ntawv tuaj yeem muaj ntau hom.
2. Kev teeb tsa lus
Lub tshuab hluav taws xob muaj ob hom lus (Lus Askiv thiab Lus Suav). Xovxwm Kev siv hluav taws xob → System → Lus , xaiv hom lus uas xav tau. Qhov kev teeb tsa no tau muab khaws cia rau hauv lub cim xeeb uas tsis yog qhov tsis hloov pauv thiab yuav tsis cuam tshuam los ntawm Kev Ua Haujlwm Teeb Meem.
Lus Askiv InterfaceSuav Interface 3. Fais fab
Xaiv SDG2000X qhov teeb tsa thaum lub tshuab hluav taws xob qhib. Muaj ob txoj kev xaiv: qhov teeb tsa lub neej ntawd thiab qhov chaw zaum kawg tau teeb tsa thaum lub tshuab hluav taws xob zaum kawg. Thaum xaiv, qhov teeb tsa yuav raug siv thaum lub ntsuas hluav taws xob qhib. Qhov kev teeb tsa no tau muab khaws cia rau hauv lub cim xeeb uas tsis yog qhov tsis hloov pauv thiab yuav tsis cuam tshuam los ntawm Kev Ua Haujlwm Teeb Meem.

Kawg: suav nrog tag nrho cov kab ke thiab cov xeev, tshwj tsis yog lub xeev tso tawm channel.
Default: qhia lub Hoobkas ua ntej tshwj tsis yog qee yam tsis muaj (xws li Lus).
Tus neeg siv: thauj cov kev teeb tsa hauv cov neeg siv tau teev tseg file thaum fais fab tuag

4. Teem rau Default
Xovxwm Utility → System → Teem Rau Default, teeb lub system mus rau qhov chaw nyob. Lub neej ntawd nqis ntawm lub system yog raws li nram no:
Table 2-33 Factory Default Setting

Tso zis	Default
Muaj nuj nqi	Sine yoj
Ntau zaus	1 kHz
Amplitude/offset	4 Vpp/0 Vdc
Theem	0° Nws
Thauj khoom	Siab Z
Modulation	Default
Tus neeg nqa khoom	1 kHz Sine Wave
Module	100Hz Sine Wave

AM Qhov tob	100%
FM Deviation	100 Hz
NUG Key Frequency	100 Hz
FSK Qhov tseem ceeb zaus	100 Hz
FSK Hop zaus	1MHz
PSK Key Zaus	100 Hz
PM Phase Deviation	100° Nws
PWM Width Dev	190 m s
cheb	Default
Pib / Nres zaus	500Hz / 1.5kHz
Sweep Sijhawm	1s
Trig tawm	Tawm
Hom	Tawm
Kev taw qhia	↑
tawg	Default
Lub Sijhawm tawg	10ms ib
Pib Theem	0° Nws
Lub voj voog	1 Lub voj voog
Trig tawm	Tawm
ncua	521 XNUMX nsq
Ua rau	Default
Qhov chaw	Sab hauv

5 ib. Beeper
Qhib los yog lov tes taw lub beeper. Xovxwm Utility → System → Beeper xaiv "On" lossis "Off"
thiab lub neej ntawd yog "On".
6. Tshuaj ntsuam qhov ntsuas
Qhib lossis kaw qhov screen saver. Xovxwm Utility → System → Page 1/2 → ScrnSvr xaiv "On" lossis "Off" thiab lub neej ntawd yog "Off". Screen saver yuav qhib yog tias tsis muaj dab tsi tshwm sim hauv lub sijhawm koj tau xaiv. Nyem qhov kov screen lossis Nias ib qho yuam sij kom rov pib dua.
7. Cov ntaub ntawv pov thawj
Xaiv qhov System Info xaiv ntawm cov ntawv qhia zaub mov rau view lub tshuab hluav taws xob cov ntaub ntawv kaw lus, suav nrog lub sijhawm pib, software version, hardware version, qauv thiab tus lej xov tooj.8. Hloov tshiab
Lub software version thiab configuration file ntawm lub tshuab hluav taws xob tuaj yeem hloov kho ncaj qha ntawm U-disk.
Ua raws li cov kauj ruam hauv qab no:

Ntxig U-disk nrog firmware hloov tshiab file (*.ADS) thiab configuration file (*.CFG) rau USB host interface ntawm lub vaj huam sib luag pem hauv ntej ntawm lub tshuab hluav taws xob.
Nias Utility → Page 1/2 → Firmware Update . Lossis nias Khw / Rov qab ncaj qha.
Xaiv lub firmware file (*.ADS) thiab xaiv Recall los hloov kho qhov system software.
Tom qab kev hloov kho tiav lawm, lub tshuab hluav taws xob yuav rov pib dua.

Nco tseg:

Tsis txhob txiav tawm lub zog thaum lub tshuab hluav taws xob tau hloov kho!
Ib configuration file (*.CFG) tej zaum yuav lossis tsis suav nrog kev hloov kho firmware. Yog CFG file tsis suav nrog firmware hloov tshiab ces nws yuav tsis tas rau qhov hloov tshiab ntawd.

9. Ua-nyob rau hauv pab System
Lub SDG2000X muab ib qho kev pab ua ke, uas cov neeg siv tau view cov ntaub ntawv pab tau txhua lub sijhawm thaum ua haujlwm ntawm qhov ntsuas. Xovxwm Utility → System → Page 1/2 → Pab nkag mus rau hauv qab no interface.Table 2-34 Help Menu Explanations

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
UP		Cursor upward los xaiv.
nqes		Cursor downward los xaiv.
Xaiv		Nyeem cov ntaub ntawv pab cuam tam sim no.
Tso tseg		Tawm hauv qhov kev pab cuam built-in.

Muaj 10 lub ntsiab lus hauv daim ntawv pab. Koj tuaj yeem siv lub pob qhov rooj thiab / lossis cov ntawv qhia ua haujlwm los xaiv cov ntaub ntawv pabcuam uas koj xav nyeem.
2.13.2 Test/Cal
Xaiv Utility → Test/Cal , to nkag mus rau hauv qab no interface.Table 2-35 Menu Kev piav qhia ntawm Kev Ntsuas / Cal Setting

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Piav
Kev kuaj tus kheej		Ua ib qho kev ntsuas tus kheej.
TouchCal		Ua ib qho screen calibration.
Rov qab los		Rov qab mus rau Utility menu.

Kev kuaj tus kheej
Xovxwm Utility → Test/Cal → SelfTest, nkag mus rau cov ntawv qhia zaub mov nram qab no.Table 2-36 Menu Explanations of Self Test

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Piav
ScrTest		Khiav qhov kev ntsuam xyuas qhov screen.
KeyTest		Khiav cov ntawv xeem keyboard.
LEDTest		Khiav qhov kev ntsuas ntsuas qhov ntsuas qhov tseem ceeb.
BoardTest		Khiav hardware circuit self-test program.
Tso tseg		Rov qab mus rau Test/Cal menu.

1. ScrTest
Xaiv ScrTest nkag mus rau qhov screen test interface. Cov lus ceeb toom 'Thov nias '7' tus yuam sij txuas ntxiv, nias '8' tus yuam sij tawm.' yog tso tawm. Nias lub '7' tus yuam sij rau kev sim thiab saib yog tias muaj qhov sib txawv xim loj, pixel tsis zoo lossis kev ua yuam kev.2. Kev Xeem Xeem
Xaiv KeyTest kom nkag mus rau cov keyboard xeem interface, cov duab ntawm cov duab plaub dawb ntawm lub vijtsam sawv cev rau cov yuam sij hauv pem hauv ntej. Lub voj voog ntawm ob tus xub sawv cev rau lub pob qhov rooj. Kuaj tag nrho cov yuam sij thiab pob qhov rooj thiab xyuas kom meej tias tag nrho cov yuam sij backlight teeb pom kev raug. Qhov chaw sib thooj ntawm cov yuam sij kuaj lossis pob qhov rooj yuav tso tawm xim xiav.
Sab saum toj ntawm qhov screen qhia 'Thov nias '8' yuam sij peb zaug kom tawm.
3. LED Test
Xaiv LEDTest kom nkag mus rau qhov kev ntsuam xyuas LED interface, cov duab ntawm lub vijtsam dawb daim duab plaub sawv cev rau cov yuam sij hauv pem hauv ntej. Cov lus ceeb toom 'Thov nias '7' Ntsiab lus txuas ntxiv, nias '8' Ntsiab Lus tawm.' yog tso tawm. Nias tus yuam sij '7' tsis tu ncua rau kev sim thiab thaum tus yuam sij tau teeb, thaj chaw sib thooj ntawm qhov screen yuav tso tawm xim xiav. 4. Board Test
Xaiv BoardTest nkag mus rau hauv qab no interface. Kov Kho
Siv cov haujlwm tsis tu ncua los ntsuas lub vijtsam kov, uas ua rau nws muaj tseeb dua thaum tus ntiv tes lossis tus cwj mem kov kov lub vijtsam thiab zam kev ua haujlwm tsis raug.
Xovxwm Utility → Test/Cal → TouchCal , nkag mus rau hauv qab no interface. Raws li cov lus, nyem lub voj voog liab nyob rau sab sauv sab laug, sab xis sab xis, sab laug ces kaum thiab sab xis kaum ntawm lub vijtsam hauv ntu. Tom qab kov calibration ua tiav, lub kaw lus yuav tso saib cov lus qhia hauv qab no. Tom qab ntawd nias txhua tus yuam sij lossis kov lub vijtsam kom tawm ntawm lub interface tam sim no.2.13.3 Counter
Lub SDG2000X muab qhov ntsuas zaus uas tuaj yeem ntsuas qhov zaus ntawm 100mHz txog 200MHz. Lub dual channels tseem tuaj yeem tso tawm ib txwm thaum lub txee qhib. Xovxwm Kev siv hluav taws xob → Cov txee , nkag mus rau hauv qab no interface. Table 2-37 Cov Ntawv Qhia Cov Lus Qhia ntawm Zaus Counter

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Xeev	Tawm	Qhib lub txee.
Xeev	On	Kaw lub txee.
Ntau zaus		Ntsuas zaus.
Lub sijhawm		Ntsuas lub sij hawm.
PWidth		Ntsuas qhov dav dav.
NWidth		Ntsuas qhov dav tsis zoo.
RefFreq		Teeb tsa qhov siv zaus. Qhov system yuav xam qhov sib txawv ntawm qhov ntsuas zaus thiab qhov siv zaus tau txais.
TrigLev		Teem lub trigger theem voltage.
Lub luag haujlwm		Ntsuas lub luag haujlwm.
Teeb tsa		Teem lub txee configuration.
Tso tseg		Tawm ntawm qhov zaus counter interface.

Table 2-38 Cov Lus Qhia Qhia Txog Kev Teeb

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Hom	DC	Teem lub coupling hom rau DC
Hom	AC	Teem lub coupling hom rau AC
HFR	On	Qhib cov lim dej tsis txaus siab.
HFR	Tawm	Kaw cov lim dej tsis txaus siab.
Default		Teem lub zaus counter settings rau lub neej ntawd.
Hom	qeeb	Kev ntsuas qeeb thiab ntau tus lej samples
Hom	Ceev ceev	Kev ntsuas ceev thiab ob peb cov lej samples
Ua tiav		Txuag cov chaw tam sim no thiab rov qab mus rau cov ntawv qhia dhau los.

Xaiv cov Parameters los ntsuas
Lub txee zaus ntawm SDG2000X tuaj yeem ntsuas qhov ntsuas tsis xws li zaus, lub sijhawm, lub luag haujlwm, qhov dav ntawm pulse zoo thiab qhov dav pulse tsis zoo.
Kev siv zaus
Qhov system yuav xam qhov sib txawv ntawm qhov ntsuas zaus thiab qhov siv zaus tau txais.
Trigger Level
Teem lub trigger theem ntawm qhov ntsuas qhov system. Lub kaw lus ua rau thiab tau txais qhov ntsuas ntsuas thaum lub teeb liab nkag mus txog qib ntsuas qhov ntsuas. Lub neej ntawd yog 0V thiab muaj ntau yam yog los ntawm -3V txog 1.5V. Xaiv TrigLev thiab siv cov lej keyboard los nkag rau qhov xav tau thiab xaiv chav tsev (V lossis mV) los ntawm cov ntawv qhia zaub mov pop-up. Los yog siv cov pob qhov rooj thiab cov xub xub los hloov tus nqi parameter.
Hom kev sib txuas
Teem lub coupling qauv ntawm input teeb liab mus rau "AC" los yog "DC". Lub neej ntawd yog "AC".
HFR
High Frequency Rejection tuaj yeem siv los lim tawm cov khoom siv hluav taws xob ntau ntawm cov teeb liab ntsuas thiab txhim kho qhov ntsuas qhov tseeb hauv qhov ntsuas hluav taws xob tsawg.
Nias HFR kom pab tau lossis tsis ua haujlwm no. Lub neej ntawd yog "Tawm".
Ua kom Muaj Kev Tsis Txaus Siab Siab thaum lub teeb liab tsawg zaus nrog qis dua 250kHz zaus ntsuas los lim tawm cov suab nrov nrov cuam tshuam.
Disable High Frequency Rejection thaum ntsuas lub teeb liab nrog lub zaus siab dua 250 KHz. Qhov siab tshaj plaws zaus uas suav tau yog 200 MHz.

2.13.4 Tso zis teeb
Xovxwm Utility → Tso zis nkag mus rau hauv qab no interface. Thauj khoom
Rau [CH1] thiab [CH2] connectors ntawm lub vaj huam sib luag pem hauv ntej, lub tshuab hluav taws xob muaj qhov tso tawm impedance ntawm 50Ω. Yog hais tias qhov tseeb load tsis phim lub teeb load, tso tawm voltage yuav tsis zoo ib yam li cov zis voltage. Qhov kev ua haujlwm no yog siv los ua kom phim cov voltage nrog qhov xav tau. Qhov kev teeb tsa no tsis tau hloov qhov tso zis impedance rau lwm tus nqi.
Cov kauj ruam rau kev teeb tsa lub load:
Xovxwm Utility → Output Setup → Load , los teeb tsa cov zis load. Lub load parameter qhia nyob rau hauv qab yog lub neej ntawd qhov chaw thaum lub hwj chim yog nyob rau los yog lub pre-set load nqi.
High impedance: tso tawm raws li HiZ;
Thauj khoom: Lub neej ntawd yog 50Ω thiab qhov ntau yog 50Ω txog 100kΩ.
Nco tseg:
Txuas ntxiv nias tus yuam sij tso zis rau ob vib nas this los hloov ntawm High Impedance thiab 50Ω.
Polarity
Xovxwm Utility → Output Setup → Polarity los teeb tsa cov teeb liab tso zis li qub lossis inverted. Lub waveform inversion yog txheeb ze rau 0V offset voltage.
Raws li qhia hauv daim duab hauv qab no. Nco tseg:
Lub Sync teeb liab hais txog lub waveform tsis inverted thaum lub waveform yog inverted.
EqPhase
Xovxwm Utility → Output Setup → EqPhase txhawm rau kho cov theem ntawm CH1 thiab CH2. Xaiv cov ntawv qhia zaub mov yuav rov teeb tsa ob txoj hauv kev thiab pab kom lub tshuab hluav taws xob tso tawm nrog cov zaus teev thiab pib theem. Rau ob lub teeb liab uas nws zaus yog tib yam lossis ntau yam ntawm qhov ntawd, qhov kev ua haujlwm no yuav ua kom lawv cov theem.
Waveforms sib xyaw
Lub CH1 tso zis chaw nres nkoj ntawm SDG2000X outputs lub waveform ntawm CH1 nyob rau hauv lub general hom, thaum lub waveform ntawm CH1 + CH2 yuav tso zis nyob rau hauv lub ua ke hom. Ib yam li ntawd, qhov chaw nres nkoj CH2 tso zis ntawm SDG2000X tso tawm lub waveform ntawm CH2 nyob rau hauv hom dav dav thaum lub waveform ntawm CH1 + CH2 tuaj yeem tso tawm hauv hom sib xyaw.
Xovxwm Utility → Output Setup → Wave Muab tso rau hauv lub waveforms combining interface, raws li qhia hauv daim duab hauv qab no.

Table 2-39 Cov Lus Qhia Qhia Txog Wave Combine

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
CH1 hloov	CH 1	Tshaj tawm lub waveform ntawm CH1.
CH1 hloov	CH1 + CH2	Tshaj tawm lub waveform ntawm CH1 + CH2.
CH2 hloov	CH 2	Tshaj tawm lub waveform ntawm CH2.
CH2 hloov	CH1 + CH2	Tshaj tawm lub waveform ntawm CH1 + CH2.
Rov qab los		Txuag cov haujlwm tam sim no thiab tawm ntawm qhov tam sim no interface.

Nco tseg:
Thaum lub waveforms combining muaj nuj nqi yog enabled, lub load ntawm ob channel yuav tsum tau teem rau tib yam nkaus xwb, default siv load tus nqi ntawm lub tam sim no ua hauj lwm channel.
Amptoj siab
Hauv qee qhov kev thov scenarios, cov neeg siv yuav tsum txwv qhov amplitude ntawm channel tso zis los xyuas kom meej tias amplitude rhiab teeb liab txais cov cuab yeej yuav tsis puas. Nias Utxoj cai → Kev teeb tsa → tam sim no nplooj 1/2 → amptoj siab nkag mus rau amplitude teeb nplooj ntawv thiab txwv qhov tso zis ntau tshaj plaws amplitude. Qhov siab tshaj plaws amplitude yog qhov siab tshaj plaws amplitude uas lub cuab yeej muab tau. Nws yuav siv tau rau ob lub channel tam sim ntawd tom qab teeb tsa.
Fais fab ntawm cov zis raws li txoj cai
Hauv qee qhov kev thov, tus neeg siv yuav tsum tau qhib lub hwj chim ntawm channel tso zis sai li sai tau thaum lub hwj chim ntawm channel qhib. Xovxwm Utility → Output Setup → tam sim no nplooj 1/2 → fais fab ntawm cov zis raws li txoj cai → teeb tsa "ua". Qhov no muaj nuj nqi yuav tsum tau teem lub hwj chim rau lub xeem los yog tus neeg siv-txhais hom. Xa mus rau ntu 2.13.1 rau cov chaw tshwj xeeb
2.13.5 CH Copy/coupling
Channel Copy
SDG2000X txhawb nqa lub xeev thiab waveform luam ua haujlwm ntawm nws ob txoj kev. Qhov ntawd yog hais tias, nws luam tawm tag nrho cov kev txwv thiab lub xeev (nrog rau cov channel tso zis lub xeev) thiab cov ntaub ntawv tsis txaus ntseeg ntawm ib qho channel mus rau lwm qhov.
Xovxwm Utility → CH Copy Coupling → Channel Luam, nkag mus rau hauv qab no interface.Table 2-40 Cov Ntawv Qhia Kev piav qhia ntawm Channel Copy

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
CH1=> CH2		Luam tag nrho cov kev txwv thiab lub xeev ntawm CH1 rau CH2.
CH2=> CH1		Luam tag nrho cov kev txwv thiab lub xeev ntawm CH2 rau CH1.
Txais		Ua qhov kev xaiv tam sim no thiab rov qab mus rau Utility menu.
Tso tseg		Muab qhov kev xaiv tam sim no thiab rov qab mus rau Utility menu.

Nco tseg:
Channel coupling los yog taug qab muaj nuj nqi thiab channel luam muaj nuj nqi yog kev sib koom ua ke. Thaum channel txuas lossis khiav haujlwm tau qhib, cov ntawv qhia zaub mov Channel Copy yog muab zais.
Channel sib txuas
SDG2000X txhawb ntau zaus, amplitude thiab theem coupling. Cov neeg siv tuaj yeem teeb tsa qhov sib txawv / qhov sib txawv, amplitude sib txawv / piv los yog theem sib txawv / piv ntawm ob txoj kev. Thaum qhib kev sib txuas, CH1 thiab CH2 tuaj yeem hloov kho ib txhij. Thaum zaus, amplitude lossis theem ntawm ib channel (raws li qhov kev siv) tau hloov pauv, qhov sib thooj ntawm lwm cov channel yuav raug hloov pauv thiab ib txwm khaws qhov sib txawv ntawm qhov sib txawv / qhov sib txawv, amplitude sib txawv / piv los yog theem sib txawv / piv piv rau lub hauv paus channel.
Xovxwm Utility → CH Copy Coupling → Channel Coupling , nkag mus rau hauv qab no interface.

Frequency Coupling

Txhawm rau ua kom muaj kev sib txuas zaus
Nias FreqCoup kom tig zaus coupling "On" lossis "Tawm". Lub neej ntawd yog "Tawm".
Txhawm rau xaiv zaus Coupling hom
Nias FreqMode los xaiv "Deviation" lossis "Ratio", thiab tom qab ntawd siv tus lej keyboard lossis pob qhov rooj thiab xub yuam sij los nkag rau tus nqi xav tau.
Deviation: qhov sib txawv ntawm CH1 thiab CH2. Cov teeb liab tshwm sim yog sawv cev los ntawm: FreqCH2-FreqCH1=FreqDev.
Qhov ratio: Qhov zaus piv ntawm CH1 thiab CH2. Cov teeb liab tshwm sim yog sawv cev los ntawm: Freq CH2 / Freq CH1 = FreqRatio.

AmpLitude Coupling

Txhawm rau pab AmpLitude Coupling Function
Xovxwm AmplCoup tig ampLitude coupling "On" lossis "Off". Lub neej ntawd yog "Tawm".
Xaiv AmpLitude Coupling Hom
Xovxwm AmplMode xaiv "Deviation" lossis "Ratio", thiab tom qab ntawd siv tus lej keyboard lossis pob qhov rooj thiab cov xub xub los nkag rau tus nqi xav tau.
Sib txawv: tus ampLitude sib txawv ntawm CH1 thiab CH2. Lub teeb liab tshwm sim yog sawv cev los ntawm: Ampl CH 2 -Ampl CH1 =AmplDev.
Qhov ratio: tus ampLitude ratio ntawm CH1 thiab CH2. Lub teeb liab tshwm sim yog sawv cev los ntawm: Ampl CH 2 /Ampl CH1 =AmplRatio.

Phase Coupling

Txhawm rau pab kom Theem Coupling Function
Nias PhaseCoup kom tig theem txuas "On" lossis "Tawm". Lub neej ntawd yog "Tawm".
Xaiv Phase Coupling Hom
Nias PhaseMode los xaiv "Deviation" lossis "Ratio", thiab tom qab ntawd siv tus lej keyboard lossis pob qhov rooj thiab cov xub xub los nkag rau tus nqi xav tau.
Sib txawv: Theem deviation ntawm CH1 thiab CH2. Cov teeb liab tshwm sim yog sawv cev los ntawm: Theem CH2 - Phase CH1 = PhaseDev.
Qhov ratio: theem piv ntawm CH1 thiab CH2. Cov teeb liab tshwm sim yog sawv cev los ntawm: Theem CH2 / Phase CH1 = PhaseRatio.

Cov ntsiab lus tseem ceeb:

Channel coupling tsuas yog muaj thaum ob qho tib si waveforms ntawm ob txoj kab yog qhov yooj yim waveforms suav nrog Sine, Square, Ramp, Pulse thiab Arbitrary.
Thaum Theem Coupling muaj nuj nqi qhib, yog tias theem ntawm ib channel hloov pauv, theem ntawm lwm cov channel yuav raug hloov raws li. Nyob rau ntawm lub sijhawm no, kev sib koom ua ke ntawm ob txoj hauv kev tuaj yeem ua tiav yam tsis muaj kev ua haujlwm Eqphase.
Channel coupling thiab channel muaj nuj nqi yog kev sib koom ua ke. Thaum channel txuas txuas tau qhib, cov ntawv qhia zaub mov Channel Luam tau muab zais.

Channel Track
Thaum txoj haujlwm khiav tau qhib, los ntawm kev hloov pauv qhov tsis muaj lossis lub xeev ntawm CH1, qhov sib thooj lossis cov xeev ntawm CH2 yuav raug hloov kho rau tib qhov nqi lossis lub xeev tau txais. Lub sijhawm no, ob lub channel tuaj yeem tso tawm tib lub teeb liab.
Xaiv Utility → CH Copy Coupling → Track kom pab tau lossis lov tes taw txoj haujlwm khiav. Thaum txoj haujlwm khiav tau qhib, channel luam thiab coupling ua haujlwm raug kaw; tus neeg siv interface tau hloov mus rau CH1 thiab tsis tuaj yeem hloov mus rau CH2, raws li qhia hauv daim duab hauv qab no.

Nias PhaseDev kom nkag mus rau hauv qab no interface. Tom qab ntawd siv tus lej keyboard lossis pob qhov rooj thiab cov xub xub los nkag rau tus nqi xav tau rau theem sib txawv ntawm CH1 thiab CH2. Lub teeb liab tshwm sim yog sawv cev los ntawm: PhaseCH2-PhaseCH1 = PhaseDev. Trigger CH
Teem kev sib raug zoo ntawm ob lub channel ua rau cov teeb liab
Xovxwm Trigger CH xaiv "Tib CH" lossis "Dual CH".

Ib leeg CH: Lub teeb liab ua haujlwm tsuas yog ua haujlwm ntawm cov channel tam sim no.
Dual CH: Lub teeb liab ua rau ntawm ob lub channel ib txhij

Xovxwm Utility → CH Copy Coupling → Trigger CH , nkag mus rau hauv qab no interface. Nco tseg:
Rau example, ob lub channel qhib cheb thiab teeb tsa phau ntawv txhais. Thaum "ib leeg CH" raug teeb tsa, lub teeb liab tshwm sim los ntawm tus kheej. Tsuas yog cov channel tam sim no tso tawm cheb thiab lwm qhov channel tsis muaj qhov tso tawm; Thaum teeb tsa "Dual CH", lub teeb liab tshwm sim los ntawm txhais tes, thiab ob qho tib si yuav tso tawm cheb.
2.13.6 Chaw taws teeb Interface
SDG2000X tuaj yeem tswj tau nyob deb ntawm USB, LAN thiab GPIB (kev xaiv) interfaces. Cov neeg siv tuaj yeem teeb tsa cov interface sib xws raws li lawv xav tau.
Xovxwm Utility → Page 1/2 → Interface qhib cov ntawv qhia zaub mov nram qab no. Tus neeg siv tuaj yeem teem caij LAN lossis GPIB chaw nyob. Table 2-41 Cov Ntawv Qhia piav qhia ntawm Interface

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
GPIB		Set the GPIB address.
LAN State	On	Qhib LAN.
LAN State	Tawm	Tua tawm LAN.
Teeb LAN		Teem tus IP chaw nyob, subnet mask thiab rooj vag.
Txais		Txuag cov chaw tam sim no thiab rov qab mus rau Utility menu.

SDG2000X tuaj yeem tswj tau nyob deb ntawm ob txoj hauv qab no:
1. Tus neeg siv-txhais programming
Cov neeg siv tuaj yeem ua haujlwm thiab tswj cov cuab yeej los ntawm kev siv SCPI cov lus txib (Cov Lus Qhia rau Cov Khoom Siv Hluav Taws Xob). Yog xav paub ntxiv txog cov lus txib thiab kev ua haujlwm, thov mus rau "Kev Tswj Xyuas Chaw Taws Teeb".
2 ib. PC software
Cov neeg siv tuaj yeem siv PC software Measurement & Automation Explorer ntawm NI (National Instruments Corporation) xa cov lus txib los tswj cov cuab yeej remotely.

Chaw taws teeb tswj ntawm USB
SDG2000X tuaj yeem sib txuas lus nrog PC los ntawm USBTMC raws tu qauv. Koj raug pom zoo kom ua raws li cov kauj ruam hauv qab no.

Txuas lub cuab yeej.
Txuas USB Device interface ntawm lub vaj huam sib luag tom qab ntawm SDG2000X nrog lub PC ntawm USB cable.
Nruab tus tsav tsheb USB.
NI Visa raug pom zoo.
Sib txuas lus nrog lub PC tej thaj chaw deb
Qhib Kev Ntsuas & Automation Explorer ntawm NI thiab xaiv cov npe khoom siv sib xws.
Tom qab ntawd nyem "Qhib VISA Test Vaj Huam Sib Luag" txhawm rau qhib lub chaw taws teeb tswj vaj huam sib luag uas koj tuaj yeem xa cov lus txib thiab nyeem cov ntaub ntawv.

Remote Control via GPIB
Txhua lub cuab yeej txuas nrog GPIB interface yuav tsum muaj qhov chaw nyob tshwj xeeb. Lub neej ntawd tus nqi yog 18 thiab qhov tseem ceeb ntawm 1 txog 30. Qhov chaw nyob xaiv tau muab khaws cia rau hauv lub cim xeeb uas tsis yog-volatile.

Txuas lub cuab yeej.
Txuas lub tshuab hluav taws xob rau lub computer siv USB rau GPIB adapter (kev xaiv).
Nco tseg: Thov nco ntsoov tias lub PC muaj GPIB interface card ntsia.
Txuas lub USB davhlau ya nyob twg ntawm USB rau GPIB adapter rau USB Host interface ntawm lub vaj huam sib luag pem hauv ntej ntawm lub tshuab hluav taws xob thiab GPIB lub davhlau ya nyob twg mus rau GPIB daim npav davhlau ya nyob twg ntawm PC.
Nruab tus tsav tsheb ntawm GPIB card.
Thov nruab tus tsav tsheb rau daim npav GPIB uas tau txuas nrog koj lub PC.
Set the GPIB address.
Xaiv Utility → Page 1/2 → Interface → GPIB kom nkag mus rau hauv qab no interface.
Cov neeg siv tuaj yeem siv lub pob qhov rooj, cov yuam sij xub lossis cov lej keyboard hloov tus nqi thiab nias Txais kom txuag tau qhov chaw tam sim no.
Sib txuas lus nrog PC remotely
Qhib Kev Ntsuas & Automation Explorer ntawm NI. Tom qab ntxiv GPIB cov cuab yeej ua tiav, xaiv cov npe khoom siv sib xws. Tom qab ntawd nyem "Qhib VISA Test Vaj Huam Sib Luag" txhawm rau qhib lub chaw taws teeb tswj vaj huam sib luag uas koj tuaj yeem xa cov lus txib thiab nyeem cov ntaub ntawv.

Chaw taws teeb tswj ntawm LAN
SDG2000X tuaj yeem sib txuas lus nrog PC los ntawm LAN interface. Cov neeg siv tau view thiab hloov cov kev txwv LAN.

Txuas lub cuab yeej.
Txuas lub tshuab hluav taws xob rau koj lub PC lossis LAN ntawm koj lub PC siv lub network cable.
Configure network parameters.
Xaiv Utility → Page 1/2 → Interface → LAN State kom qhib LAN. Ces xaiv
LAN Teeb kom nkag mus rau hauv qab no interface.
1. Txhawm rau teeb IP chaw nyob
  Cov hom ntawv ntawm IP chaw nyob yog nnn.nnn.nnn.nn. Thawj nnn yog nyob ntawm 1 txog 223 thiab lwm qhov sib txawv ntawm 0 txog 255. Koj raug pom zoo kom tau txais ib qho chaw nyob IP los ntawm koj tus thawj tswj hwm network.
  Nias IP Chaw nyob thiab siv tus xub yuam sij thiab cov lej keyboard lossis pob khawm kom nkag mus rau koj qhov chaw nyob IP uas xav tau. Qhov chaw khaws cia rau hauv lub cim xeeb uas tsis yog-volatile thiab yuav raug loaded txiav thaum
  lub generator yog powered nyob rau lwm lub sij hawm.
2. Txhawm rau teeb Subnet Mask
  Cov hom ntawv ntawm lub npog ntsej muag yog nnn.nnn.nnn.nnn thiab txhua qhov nnn nyob ntawm 0 txog 255. Koj raug pom zoo kom tau txais ib daim npog ntsej muag muaj los ntawm koj tus thawj coj hauv lub network.
  Nias Subnet Mask thiab siv tus xub yuam sij thiab cov lej keyboard lossis pob qhov rooj nkag mus rau koj lub ntsej muag subnet xav tau. Qhov chaw yog khaws cia rau hauv lub cim xeeb uas tsis yog-volatile thiab yuav raug loaded cia li thaum lub tshuab hluav taws xob yog powered nyob rau lwm lub sij hawm.
3. Txhawm rau teeb Gateway
  Lub hom phiaj ntawm lub rooj vag yog nnn.nnn.nnn.nnn thiab txhua qhov nnn yog li ntawm 0 txog 255. Nws raug nquahu kom tau txais lub rooj vag muaj los ntawm koj tus thawj tswj hwm network.
  Nias Gateway thiab siv tus xub yuam sij thiab cov lej keyboard lossis pob qhov rooj nkag mus rau koj lub qhov rooj uas koj xav tau. Qhov chaw yog khaws cia rau hauv lub cim xeeb uas tsis yog-volatile thiab yuav raug loaded cia li thaum lub tshuab hluav taws xob yog powered nyob rau lwm lub sij hawm.
  Nco tseg:
  • Yog tias lub tshuab hluav taws xob txuas nrog PC ncaj qha, teeb tsa IP chaw nyob, lub qhov ncauj qhov ntswg subnet thiab lub rooj vag rau ob qho tib si ntawm PC thiab lub tshuab hluav taws xob. Lub qhov ncauj qhov ntswg subnet thiab lub rooj vag ntawm PC thiab lub tshuab hluav taws xob yuav tsum yog tib yam thiab IP chaw nyob ntawm lawv yuav tsum nyob hauv tib ntu ntu.
  • Yog tias lub tshuab hluav taws xob txuas nrog LAN ntawm koj lub PC, thov hu rau koj tus thawj tswj hwm network kom tau txais qhov chaw nyob IP. Yog xav paub ntxiv, xa mus rau TCP/IP raws tu qauv.
4. DHCP Configuration Hom
  Hauv DHCP hom, DHCP neeg rau zaub mov hauv lub network tam sim no muab cov kev txwv LAN, xws li IP chaw nyob, rau lub tshuab hluav taws xob. Nias DHCP los xaiv "On" lossis "Tawm" kom tig DHCP hom rau lossis tawm.
  Lub neej ntawd yog "Tawm".
Sib txuas lus nrog PC remotely
Qhib Kev Ntsuas & Automation Explorer ntawm NI. Tom qab ntxiv LAN ntaus ntawv (VISA TCP/IP Resource…) ua tiav, xaiv cov khoom siv lub npe. Tom qab ntawd nyem "Qhib VISA Test Vaj Huam Sib Luag" txhawm rau qhib lub chaw taws teeb tswj vaj huam sib luag uas koj tuaj yeem xa cov lus txib thiab nyeem cov ntaub ntawv.

2.13.7 Sync tso zis
Lub tshuab hluav taws xob muab Sync tso zis los ntawm [Aux In/Out] connector ntawm lub vaj huam sib luag nram qab. Thaum lub synchronization nyob rau, qhov chaw nres nkoj tuaj yeem tso tawm lub teeb liab CMOS nrog tib zaus raws li cov qauv siv hluav taws xob (tshwj tsis yog Suab nrov thiab DC), arbitrary waveforms, thiab modulated waveforms (tshwj tsis yog cov qauv sab nraud).

Table 2-42 Ntawv qhia zaub mov piav qhia txog Sync Output

Muaj nuj nqi Ntawv qhia zaub mov	Chaw	Kev piav qhia
Xeev	Tawm	Kaw cov zis sync
Xeev	On	Qhib cov zis sync
Channel	CH 1	Teem lub teeb liab sync ntawm CH1.
Channel	CH 2	Teem lub teeb liab sync ntawm CH2.
Txais		Txuag cov chaw tam sim no thiab rov qab mus rau Utility menu.
Tso tseg		Muab cov kev teeb tsa tam sim no thiab rov qab mus rau Utility menu.

Sync teeb liab ntawm txawv Waveforms:
Basic Waveform thiab Arbitrary Waveform

Thaum qhov zaus ntawm lub waveform tsawg dua los yog sib npaug rau 10MHz, lub teeb liab sync yog a
Pulse nrog 50ns mem tes dav thiab tib zaus raws li lub waveform.
Thaum qhov zaus ntawm lub waveform ntau dua 10MHz, tsis muaj cov teeb liab synchronization.
Suab nrov thiab DC: tsis muaj synchronization teeb liab tso zis.

Modulated Waveform

Thaum xaiv sab hauv modulation, lub teeb liab sync yog Pulse nrog 50ns mem tes dav.
Rau AM, FM, PM thiab PWM, qhov zaus ntawm lub teeb liab synchronization yog qhov hloov pauv zaus.
Rau ASK, FSK thiab PSK, qhov zaus ntawm lub teeb liab sync yog qhov tseem ceeb zaus.
Thaum xaiv cov kev hloov kho sab nraud, tsis muaj cov teeb liab synchronization, rau [Aux In/Out] connector ntawm lub vaj huam sib luag tom qab yog siv los nkag rau sab nraud modulating teeb liab.

Sweep thiab tawg Waveform
Thaum Sweep los yog tawg muaj nuj nqi yog qhib, tsis muaj sync teeb liab tso zis thiab Sync ntawv qhia zaub mov yog muab zais.

2.13.8 Clock Source
SDG2000X muab ib qho 10MHz moos qhov chaw. Nws kuj tseem tuaj yeem lees txais lub moos sab nraud hauv daim ntawv [10 MHz Hauv / Tawm] txuas ntawm lub vaj huam sib luag tom qab. Nws tseem tuaj yeem tso tawm lub moos los ntawm [10 MHz Hauv / Tawm] txuas rau lwm yam khoom siv.
Nias Utility → Page 1/2 → Clock → Source los xaiv “Internal” lossis “External”. Yog tias xaiv "sab nraud", lub cuab yeej yuav kuaj xyuas seb lub teeb liab lub moos sab nraud puas siv tau los ntawm [10MHz In/Out] connector ntawm lub vaj huam sib luag tom qab. Yog tias tsis yog, cov lus ceeb toom "Tsis muaj lub moos sab nraud!" yuav tso saib lub moos qhov chaw rau "sab nraud".

Sync txoj kev rau ob los yog ntau dua twj paj nruag:

Synchronization ntawm ob lub cuab yeej
Txuas lub [10MHz Hauv / Tawm] txuas ntawm lub tshuab hluav taws xob A (siv lub moos sab hauv) mus rau [10MHz Hauv / Tawm] txuas ntawm lub tshuab hluav taws xob B (siv lub moos sab nraud) thiab teeb tsa cov zis zaus ntawm A thiab B raws li tus nqi tib yam kom paub txog synchronization .
Synchronization ntawm ntau yam cuab yeej
Faib lub 10MHz moos qhov chaw ntawm lub tshuab hluav taws xob (siv lub moos sab hauv) rau hauv ntau txoj hauv kev, thiab tom qab ntawd txuas lawv mus rau [10MHz Hauv / Tawm] cov khoom sib txuas ntawm lwm lub tshuab hluav taws xob (siv lub moos sab nraud), thiab thaum kawg teeb tsa cov zis ntau zaus ntawm txhua lub tshuab hluav taws xob raws li tib tus nqi kom paub synchronization.

2.13.9 hom
Nias Utility → Nplooj 1/2 → Hom nkag mus rau hom teeb tsa Interface, raws li pom hauv daim duab 2-82.

Phase-locked hom
Thaum hloov qhov zaus, DDSs ntawm ob txoj kab rov pib dua, thiab cov theem sib txawv ntawm CH1 thiab CH2 raug tswj xyuas.

Hom kev ywj pheej
Thaum hloov qhov zaus, tsis yog cov channel 'DDS rov pib dua thiab qhov sib txawv ntawm CH1 thiab CH2 hloov ntawm random. Thaum txoj kev ywj pheej qhib, cov theem tsis tuaj yeem hloov kho thiab cov ntawv qhia theem tau muab zais, raws li pom hauv daim duab 2-84.

2.13.10 Hloov pauvtage Kev Tiv Thaiv
Xaiv Utility → Page 1/2 → OverVoltage Kev Tiv Thaiv kom qhib lossis tawm haujlwm, raws li pom hauv daim duab hauv qab no.

Yog hais tias lub xeev teem rau ON, overvoltage kev tiv thaiv ntawm CH1 thiab CH2 yuav siv tau thaum ib qho ntawm cov xwm txheej hauv qab no tau ua tiav. Thaum overvoltage kev tiv thaiv tshwm sim, ib cov lus yuav tshwm sim thiab cov zis yog neeg xiam.

Tus nqi kiag li input voltage yog siab tshaj 11V ± 0.5V thaum lub amplitude ntawm lub tshuab hluav taws xob yog siab dua lossis sib npaug rau 3.2Vpp lossis DC offset siab dua lossis sib npaug rau |2VDC|.
Tus nqi kiag li input voltage yog siab tshaj 4V ± 0.5V thaum lub ampLitude ntawm lub tshuab hluav taws xob qis dua 3.2Vpp lossis DC offset qis dua |2VDC|.

2.13.11 Multi-Device Synchronization
Synchronization ntawm zaus thiab kev ua kom zoo ntawm cov theem tuaj yeem pom tau ntawm ob lossis ntau dua SDG2000X li los ntawm kev siv Multi-Device Sync muaj nuj nqi.
Cov kauj ruam ua haujlwm tshwj xeeb yog raws li hauv qab no:

Tom qab nkag mus rau ntau lub cuab yeej synchronization teeb tsa interface, teeb tsa "Sync Status" ntawm txhua yam khoom siv rau "On".
Teem ib qho ntawm cov khoom siv ua "Master" thiab lwm yam khoom siv li "Slave".
Txuas lub [Aux In/Out] ntawm tus tswv mus rau [Aux In/Out] ntawm lwm tus qhev raws.
Txuas tus [10MHz Tawm] txuas ntawm tus Tswv mus rau [10MHz Hauv] txuas ntawm tus qhev thawj, thiab tom qab ntawd txuas lub [10MHz Tawm] txuas ntawm thawj tus qhev mus rau [10MHz Hauv] txuas ntawm tus qhev thib ob, thiab lwm yam.
Teem tib qhov tso zis ntau zaus rau txhua lub tshuab hluav taws xob.
Nias lub pob "Sync Device" ntawm tus Xib Hwb los siv synchronization.

Xaiv Utility → Page 1/3 → Page 2/3 → Multi-Device Sync kom tig rau txoj haujlwm, raws li qhia hauv daim duab hauv qab no.

Qhib tus tswv hom raws li qhia hauv qab no hauv daim duab hauv qab no.

CEEB TOOM:
Lub teeb liab synchronous kis tau los ntawm [Aux In/Out] ntawm Master mus rau [Aux In/Out] ntawm tus qhev los ntawm BNC cable thaum Sync Devices raug nias. Muaj qee qhov qeeb ntawm lub sijhawm thaum tus tswv xa cov teeb liab synchronous thiab lub sijhawm thaum tus qhev tau txais nws.
Yog li, cov zis waveforms los ntawm cov tshuab hluav taws xob sib txawv yuav muaj qee theem sib txawv ntsig txog BNC cable. Cov neeg siv tuaj yeem kho cov theem ntawm txhua tus qhev ntawm nws tus kheej kom them nyiaj rau theem sib txawv.

Examples

Txhawm rau pab tus neeg siv tswv yuav siv SDG2000X zoo dua, peb muab qee tus examples hauv kev nthuav dav. Txhua tus examples hauv qab no siv lub neej ntawd teeb tsa ntawm qhov ntsuas tshwj tsis yog tshwj xeeb.
Tshooj lus no suav nrog cov ntsiab lus hauv qab no:

Example 1: Tsim Sine Waveform
Example 2: Tsim lub Square Waveform
Example 3: Tsim ib Ramp Waveform
Example 4: Tsim Pulse Waveform
Example 5: Tsim ib lub suab nrov
Example 6: Tsim DC Waveform
Example7: Tsim ib qho Linear Sweep Waveform
Example 8: Tsim ib tug tawg Waveform
Example 9: Tsim ib qho AM Modulation Waveform
Example 10: Tsim lub FM Modulation Waveform
Example 11: Tsim PM Modulation Waveform
Example 12: Tsim FSK Modulation Waveform
Example 13: Tsim ib qho ASK Modulation Waveform
Example 14: Tsim PSK Modulation Waveform
Example 15: Generate a PWM Modulation Waveform
Example 16: Tsim DSB-AM Modulation Waveform

3.1ex ibample 1: Tsim Sine Waveform
Tsim sine waveform nrog 1MHz zaus, 5Vpp amplitude thiab 1Vdc offset.

➢ Cov kauj ruam:

Teeb qhov zaus.
1. Nias Waveforms → Sine → Zaus / Lub Sijhawm thiab xaiv Zaus uas yuav tso tawm xim xiav.
2. Ntaus '1' los ntawm cov keyboard thiab xaiv chav tsev 'MHz'. Qhov zaus yog teem rau 1MHz.
Teeb lub Amptoj siab.
1. Xovxwm Amplitude/High Level xaiv Amplitude uas yuav tso saib xiav xim.
2. Ntaus '5' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp'. Cov amplitude yog teem rau 5Vpp.
Teeb lub Offset.
1. Nias Offset/Low Level xaiv Offset uas yuav tso saib xim xiav.
2. Ntaus '1' los ntawm cov keyboard thiab xaiv lub tsev 'Vdc'. Offset yog teem rau 1Vdc.

Thaum zaus, amplitude thiab offset yog teem, lub waveform generated yog qhia nyob rau hauv daim duab 3-1.

3.2ex ibample 2: Tsim lub Square Waveform
Tsim ib square waveform nrog 5kHz zaus, 2Vpp ampLitude, 1Vdc offset thiab 30% lub voj voog ua haujlwm.
➢ Cov kauj ruam:

Teeb qhov zaus.
1. Nias Waveforms → Square → Zaus / Lub Sijhawm thiab xaiv zaus uas yuav tso tawm xim xiav.
2. Ntaus '5' los ntawm cov keyboard thiab xaiv lub tsev 'kHz'. Qhov zaus yog teem rau 5kHz.
Teeb lub Amptoj siab.
1. Xovxwm Amplitude/High Level xaiv Amplitude uas yuav tso saib xiav xim.
2. Ntaus '2' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp'. Cov amplitude yog teem rau 2Vpp.
Teeb lub Offset.
1. Nias Offset/Low Level xaiv Offset uas yuav tso saib xim xiav.
2. Ntaus '1' los ntawm cov keyboard thiab xaiv lub tsev 'Vdc'. Offset yog teem rau 1Vdc.
Teem lub Duty Cycle.
1. Nias Duty Cycle xaiv Duty Cycle uas yuav tso tawm xim xiav.
2. Ntaus '30' los ntawm cov keyboard thiab xaiv chav tsev '%'. Lub luag haujlwm yog teem rau 30%.

Thaum zaus, amplitude, offset thiab lub voj voog lub luag haujlwm tau teeb tsa, lub waveform generated yog qhia hauv daim duab 3-2.

3.3ex ibample 3: Tsim ib Ramp Waveform
Tsim aramp waveform nrog 10μs lub sijhawm, 100mVpp ampLitude, 20mVdc offset, 45 ° theem thiab 30% symmetry.
➢ Cov kauj ruam:

Teeb lub Sijhawm.
1. Xovxwm Waveforms → Ramp → Zaus / Lub Sijhawm thiab xaiv Lub Sijhawm uas yuav tso tawm xim xiav.
2. Ntaus '10' los ntawm cov keyboard thiab xaiv chav tsev 'μs'. Lub sijhawm teem rau 10μs.
Teeb lub Amptoj siab.
1. Xovxwm Amplitude/HighLevel xaiv Amplitude uas yuav tso saib xiav xim.
2. Ntaus '100' los ntawm cov keyboard thiab xaiv chav tsev 'mVpp'. Cov amplitude yog teem rau 100mVpp.
Teeb lub Offset.
1. Nias Offset/LowLevel xaiv Offset uas yuav tso tawm xim xiav.
2. Ntaus '20' los ntawm cov keyboard thiab xaiv chav tsev 'mVdc'. Lub offset yog teem rau 20mVdc.
Teeb lub Phase.
1. Nias Phase xaiv Phase uas yuav tso saib xim xiav.
2. Ntaus '45' los ntawm cov keyboard thiab xaiv chav tsev '°'. Theem yog teem rau 45 °.
Teem lub Symmetry.
1. Nias Symmetry xaiv Symmetry uas yuav tso saib xiav xim.
2. Ntaus '30' los ntawm cov keyboard thiab xaiv chav tsev '30%'. Lub symmetry yog teem rau 30%.

Thaum lub sij hawm, amplitude, offset, theem thiab symmetry yog teem, lub waveform generated yog qhia nyob rau hauv daim duab 3-3.

3.4ex ibample 4: Tsim Pulse Waveform
Tsim cov mem tes waveform nrog 5kHz zaus, 5V qib siab, -1V qis qis, 40μs mem tes dav thiab 20ns ncua.
➢ Cov kauj ruam:

Teeb qhov zaus.
1. Xovxwm Waveforms → Pulse → Zaus / Lub Sijhawm thiab xaiv Zaus , uas yuav tso saib xim xiav.
2. Ntaus '5' los ntawm cov keyboard thiab xaiv lub tsev 'kHz'. Qhov zaus yog teem rau 5 kHz.
Teem Qib Siab.
1. Xovxwm Amplitude/High Level thiab xaiv High Level uas yuav tso saib xiav xim.
2. Ntaus '5' los ntawm cov keyboard thiab xaiv chav tsev 'V'. Cov theem siab yog teem rau 5V.
Teem Qib Qib qis.
1. Nias Offset/Low Theem thiab xaiv qhov qis qis uas yuav tso tawm xim xiav.
2. Ntaus '-1' los ntawm cov keyboard thiab xaiv chav tsev 'V'. Qib qis yog teem rau -1V.
Teem lub Pul Dav.
1. Nias Pul Width/Duty Cycle thiab xaiv Pul Width uas yuav tso saib xim xiav.
2. Ntaus '40' los ntawm cov keyboard thiab xaiv chav tsev 'μs'. Lub mem tes dav yog teem rau 40μs.
Teem lub Delay.
1. Nias Delay xaiv Ncua uas yuav tso saib xim xiav.
2. Ntaus '20' los ntawm cov keyboard thiab xaiv chav tsev 'ns'. Kev ncua yog teem rau 20ns.

Thaum qhov zaus, theem siab, theem qis, mem tes dav thiab ncua sij hawm tau teeb tsa, lub waveform generated yog qhia hauv daim duab 3-4.

3.5ex ibample 5: Tsim ib lub suab nrov
Tsim lub suab nrov nrog 0.5V stdev thiab 1 V txhais tau tias.
➢ Cov kauj ruam:

Teeb lub Stdev.
1. Nias Waveforms → Suab nrov → Stdev xaiv Stdev uas yuav tso saib xim xiav.
2. Ntaus '0.5' los ntawm cov keyboard thiab xaiv chav tsev 'V'. Lub stdev yog teem rau 0.5 V.
Teeb Mean.
Nias Mean xaiv Mean uas yuav tso tawm xim xiav.
Nkag mus '1' los ntawm cov keyboard thiab xaiv chav tsev '1'. Qhov nruab nrab yog teem rau 1V.

Thaum lub stdev thiab txhais tau tias yog teem, lub suab nrov generated yog qhia nyob rau hauv daim duab 3-5.

3.6ex ibample 6: Tsim DC Waveform
Tsim DC waveform nrog 3Vdc offset,
➢ Cov kauj ruam:

Xaiv DC waveform.
Xovxwm Waveforms → Nplooj 1/2 → DC , xaiv DC waveform.
Teeb lub Offset.
1. Nias Offset thiab xaiv Offset uas yuav tso tawm xim xiav.
2. Ntaus '3' los ntawm cov keyboard thiab xaiv lub tsev 'Vdc'. DC offset yog teem rau 3Vdc.

Thaum DC offset raug teeb tsa, lub waveform generated yog qhia hauv daim duab 3-6.

3.7ex ibample7: Tsim ib qho Linear Sweep Waveform
Tsim ib lub sine sweep waveform uas nws zaus pib ntawm 100Hz thiab cheb mus rau qhov zaus ntawm 10KHz. Siv lub hom phiaj sab hauv, tawm kab cheb, thiab lub sij hawm cheb ntawm 2s.
➢ Cov kauj ruam:

Teem lub cheb muaj nuj nqi.
1. Nias Waveforms thiab xaiv lub sine waveform raws li lub cheb muaj nuj nqi.
2. Lub neej ntawd teeb tsa ntawm qhov chaw yog sab hauv.
Teeb lub amplitude thiab offset.
1. Xovxwm Amplitude/HighLevel xaiv Amplitude uas yuav tso saib xiav xim. Nkag mus '5' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp' los teeb tsa amplus 5vp.
2. Nias Offset/LowLevel xaiv Offset uas yuav tso tawm xim xiav. Nkag mus '0' los ntawm cov keyboard thiab xaiv chav tsev 'Vdc' los teeb qhov offset rau 0Vdc
Teem lub sijhawm cheb.
Nias Sweep → Nplooj 1/2 → Sweep Sijhawm , tawm tswv yim '1' los ntawm cov keyboard thiab xaiv chav tsev 's' los teem sijhawm cheb mus rau 1s.
Teeb qhov pib zaus.
Nias StartFreq, input '100' los ntawm cov keyboard thiab xaiv chav tsev 'Hz' los teeb tsa qhov pib freq rau 100Hz.
Teem lub sijhawm nres.
Nias StopFreq, input '10' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teeb tsa qhov nres freq rau 10kHz.
Teem lub sweep profiles.
Nyem Hom thiab xaiv Linear .

Thaum tag nrho cov kev ntsuas saum toj no tau teeb tsa, qhov linear sweep waveform generated yog qhia hauv daim duab 3-7.

3.8ex ibample 8: Tsim ib tug tawg Waveform
Tsim ib qho kev sib tsoo waveform nrog 5 lub voj voog. Lub sijhawm tawg yog 3ms. Siv cov cuab yeej sab hauv thiab 0 ° pib theem.
➢ Cov kauj ruam:

Teem lub burst muaj nuj nqi.
Nias Waveforms , thiab xaiv sine waveform raws li qhov tawg ua haujlwm.
Teem lub zaus, amplitude thiab offset.
1. Nias zaus / Lub Sij Hawm thiab xaiv Zaus uas yuav tso tawm xim xiav. Nkag mus '10' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teeb tsa zaus rau 10kHz.
2. Xovxwm Amplitude/HighLevel xaiv Amplitude uas yuav tso saib xiav xim. Nkag mus '4' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp' los teeb tsa amplus 4vp.
3. Nias Offset/LowLevel xaiv Offset uas yuav tso tawm xim xiav. Nkag mus '0' los ntawm cov keyboard thiab xaiv chav tsev 'Vdc' los teeb qhov offset rau 0Vdc
Teem lub hom tawg.
Nias Burst → NCycle, xaiv N-Cycle Mode. Lub neej ntawd teeb tsa ntawm qhov chaw yog sab hauv.
Teem lub sijhawm tawg.
Nias lub sij hawm tawg, tawm tswv yim '3' los ntawm cov keyboard thiab xaiv chav tsev 'ms' los teeb lub sijhawm tawg mus rau 3ms.
Teem lub sijhawm pib.
Nyem Pib Phase, nkag mus '0' los ntawm cov keyboard thiab xaiv chav tsev '°' los teeb tsa theem pib rau 0 °.
Teeb lub voj voog tawg.
Nias Cycle, Input '5' los ntawm cov keyboard thiab xaiv chav tsev 'Cycle' los teeb lub voj voog tawg rau 5.
Teeb lub ncua.
Nias Nplooj 1/2 kom xaiv ncua sij hawm, thiab nkag '100' los ntawm cov keyboard thiab xaiv chav tsev 'μs' los teeb tsa qhov ncua mus rau 100μs.

Thaum tag nrho cov ntsuas saum toj no tau teeb tsa, lub waveform generated yog qhia hauv daim duab 3-8.

3.9ex ibample 9: Tsim ib qho AM Modulation Waveform
Tsim ib qho AM modulation waveform nrog 80% qhov tob. Tus cab kuj yog sine nthwv dej nrog 10kHz zaus, thiab modulating nthwv dej yog sine yoj nrog 200Hz zaus.
➢ Cov kauj ruam:

Teem lub zaus, amplitude thiab offset ntawm cov cab kuj yoj.
1. Nias Waveforms , thiab xaiv cov sine waveform raws li cov cab kuj yoj
2. Nias zaus / Lub Sij Hawm thiab xaiv Zaus uas yuav tso tawm xim xiav. Cov tswv yim '10' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teeb tsa zaus rau 10kHz
3. Xovxwm Amplitude/HighLevel thiab xaiv Amplitude uas yuav tso saib xiav xim. Input'1' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp' los teeb tsa amplus 1vp.
4. Nias Offset/LowLevel thiab xaiv Offset uas yuav tso saib xim xiav. Input'0' los ntawm cov keyboard thiab xaiv chav tsev 'Vdc' los teeb qhov offset rau 0Vdc.
Teem lub modulation hom AM thiab tsis.
1. Nias Mod → Hom → AM , xaiv AM. Thov nco ntsoov tias cov lus qhia nyob rau nruab nrab sab laug ntawm lub vijtsam yog 'AM'.
2. Nias AM Freq, input '200' los ntawm cov keyboard thiab xaiv chav tsev 'Hz' los teeb tsa AM Freq rau 200Hz.
3. Nias AM Qhov tob, tawm tswv yim '80' los ntawm cov keyboard thiab xaiv chav tsev '%' los teeb tsa AM qhov tob rau 80%.
4. Nias Shape → Sine, xaiv sine yoj raws li lub modulating waveform.

Thaum tag nrho cov ntsuas saum toj no tau teeb tsa, lub waveform generated yog qhia hauv daim duab 3-9.

3.10ex ibample 10: Tsim lub FM Modulation Waveform
Tsim ib lub FM modulation waveform, tus cab kuj yog sine yoj nrog 10kHz zaus, thiab modulating yoj yog sine yoj nrog 1Hz zaus thiab 2kHz zaus sib txawv.
➢ Cov kauj ruam:

Teem lub zaus, amplitude thiab offset ntawm cov cab kuj yoj.
1. Nias Waveforms , thiab xaiv cov sine waveform raws li cov cab kuj yoj.
2. Nias zaus / Lub Sij Hawm thiab xaiv Zaus uas yuav tso tawm xim xiav. Cov tswv yim '10' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teeb tsa zaus rau 10kHz
3. Xovxwm Amplitude/HighLevel thiab xaiv Amplitude uas yuav tso saib xiav xim. Input'1' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp' los teeb tsa amplus 1vp.
4. Nias Offset/LowLevel thiab xaiv Offset uas yuav tso saib xim xiav. Input'0' los ntawm cov keyboard thiab xaiv chav tsev 'Vdc' los teeb qhov offset rau 0Vdc.
Teem lub modulation hom FM thiab tsis.
1. Nias Mod → Hom → FM, xaiv FM. Thov nco ntsoov tias cov lus qhia nyob rau nruab nrab sab laug ntawm lub vijtsam yog 'FM'.
2. Nias FM Freq, input '1' los ntawm cov keyboard thiab xaiv chav tsev 'Hz' los teeb FM Freq rau 1Hz.
3. Nias FM Dev, input '2' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teeb FM sib txawv rau 2kHz.
4. Nias Shape → Sine, xaiv sine yoj raws li lub modulating waveform.

Thaum tag nrho cov ntsuas saum toj no tau teeb tsa, lub waveform generated yog qhia hauv daim duab 3-10.

3.11ex ibample 11: Tsim PM Modulation Waveform
Tsim ib qho PM modulation waveform, tus cab kuj yog sine yoj nrog 10kHz zaus, thiab modulating yoj yog sine yoj nrog 2kHz zaus thiab 90 ° theem sib txawv.
➢ Cov kauj ruam:

Teem lub zaus, amplitude thiab offset ntawm cov cab kuj yoj.
1. Nias Waveforms , thiab xaiv cov sine waveform raws li cov cab kuj yoj.
2. Nias zaus / Lub Sij Hawm thiab xaiv Zaus uas yuav tso tawm xim xiav. Cov tswv yim '10' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teeb tsa zaus rau 10kHz
3. Xovxwm Amplitude/HighLevel thiab xaiv Amplitude uas yuav tso saib xiav xim. Input'5' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp' los teeb tsa amplus 5vp.
4. Nias Offset/LowLevel thiab xaiv Offset uas yuav tso saib xim xiav. Input'0' los ntawm cov keyboard thiab xaiv chav tsev 'Vdc' los teeb qhov offset rau 0Vdc.
Teem lub modulation hom PM thiab tsis.
1. Nias Mod → Hom → PM , xaiv PM. Thov nco ntsoov tias cov lus qhia nyob rau nruab nrab sab laug ntawm lub vijtsam yog 'PM'.
2. Nias PM Freq, input '2' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teem PM Freq rau 2kHz.
3. Nias Phase Dev, tawm tswv yim '90' los ntawm cov keyboard thiab xaiv chav tsev '°' los teeb lub theem sib txawv rau 90 °.
4. Nias Shape → Sine, xaiv sine yoj raws li lub modulating waveform.

Thaum tag nrho cov kev ntsuas saum toj no tau teeb tsa, lub waveform generated yog qhia hauv daim duab 3-1 1 .

3.12ex ibample 12: Tsim FSK Modulation Waveform
Tsim ib qho FSK modulation waveform nrog 200Hz qhov tseem ceeb zaus. Tus cab kuj yog sine nthwv dej nrog 10kHz zaus, thiab lub plhaw zaus yog 500Hz.
➢ Cov kauj ruam:

Teem lub zaus, amplitude thiab offset ntawm cov cab kuj yoj.
1. Nias Waveforms , thiab xaiv cov sine waveform raws li cov cab kuj yoj
2. Nias zaus / Lub Sij Hawm thiab xaiv Zaus uas yuav tso tawm xim xiav. Cov tswv yim '10' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teeb tsa zaus rau 10kHz.
3. Xovxwm Amplitude/HighLevel thiab xaiv Amplitude uas yuav tso saib xiav xim. Input'5' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp' los teeb tsa amplus 5vp.
4. Nias Offset/LowLevel thiab xaiv Offset uas yuav tso saib xim xiav. Nkag mus '0' los ntawm cov keyboard thiab xaiv chav tsev 'Vdc' los teeb qhov offset rau 0Vdc.
Teem lub modulation hom FSK thiab tsis.
1. Nias Mod → Hom → FSK, xaiv FSK. Thov nco ntsoov tias cov lus qhia nyob rau nruab nrab sab laug ntawm lub vijtsam yog 'FSK'.
2. Nias Key Freq , input '200 ' los ntawm cov keyboard thiab xaiv chav tsev 'Hz' los teeb lub zaus zaus rau 200 Hz.
3. Nias Hop Freq, input '500' los ntawm cov keyboard thiab xaiv chav tsev 'Hz' los teeb lub hop zaus rau 500Hz.

Thaum tag nrho cov ntsuas saum toj no tau teeb tsa, lub waveform generated yog qhia hauv daim duab 3-12.

3.13ex ibample 13: Tsim ib qho ASK Modulation Waveform
Tsim ib qho ASK modulation waveform nrog 500Hz qhov tseem ceeb zaus. Cov cab kuj yog sine wave nrog 5kHz zaus.
➢ Cov kauj ruam:

Teem lub zaus, amplitude thiab offset ntawm cov cab kuj yoj.
1. Nias Waveforms , thiab xaiv cov sine waveform raws li cov cab kuj yoj
2. Nias zaus / Lub Sij Hawm thiab xaiv Zaus uas yuav tso tawm xim xiav. Cov tswv yim '5' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teeb tsa zaus rau 5kHz
3. Xovxwm Amplitude/HighLevel thiab xaiv Amplitude uas yuav tso saib xiav xim. Nkag mus '5' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp' los teeb tsa amplus 5vp.
4. Nias Offset/LowLevel thiab xaiv Offset uas yuav tso saib xim xiav. Nkag mus '0' los ntawm cov keyboard thiab xaiv chav tsev 'Vdc' los teeb qhov offset rau 0Vdc.
Teem lub modulation hom ASK thiab tsis.
1. Nias Mod → Hom → NUG , xaiv ASK. Thov nco ntsoov tias cov lus qhia nyob rau nruab nrab sab laug ntawm lub vijtsam yog 'ASK'.
2. Nias Key Freq, input '500' los ntawm cov keyboard thiab xaiv chav tsev 'Hz' los teem lub zaus zaus rau 500 Hz.

Thaum tag nrho cov ntsuas saum toj no tau teeb tsa, lub waveform generated yog qhia hauv daim duab 3-13

3.14ex ibample 14: Tsim PSK Modulation Waveform
Tsim ib PSK modulation waveform nrog 200Hz qhov tseem ceeb zaus. Cov cab kuj yog sine wave nrog 1kHz zaus.
➢ Cov kauj ruam:

Teem lub zaus, amplitude thiab offset ntawm cov cab kuj yoj.
1. Nias Waveforms , thiab xaiv cov sine waveform raws li cov cab kuj yoj
2. Nias zaus / Lub Sij Hawm thiab xaiv Zaus uas yuav tso tawm xim xiav. Cov tswv yim '1' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teeb tsa zaus rau 1kHz
3. Xovxwm Amplitude/HighLevel thiab xaiv Amplitude uas yuav tso saib xiav xim. Nkag mus '5' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp' los teeb tsa amplus 5vp.
4. Nias Offset/LowLevel thiab xaiv Offset uas yuav tso saib xim xiav. Nkag mus '0' los ntawm cov keyboard thiab xaiv chav tsev 'Vdc' los teeb qhov offset rau 0Vdc.
Teem lub modulation hom PSK thiab tsis.
Nias Mod → Hom → Nplooj 1/2 → PSK, xaiv PSK. Thov nco ntsoov tias cov lus qhia nyob rau nruab nrab sab laug ntawm lub vijtsam yog 'PSK'.
Nias Key Freq , input '200' los ntawm cov keyboard thiab xaiv chav tsev 'Hz' los teeb tsa qhov tseem ceeb zaus rau 200 Hz.
Xovxwm Polarity → Zoo.

Thaum tag nrho cov ntsuas saum toj no tau teeb tsa, lub waveform generated yog qhia hauv daim duab 3-14.

3.15ex ibample 15: Generate a PWM Modulation Waveform
Tsim ib qho PWM hloov pauv waveform nrog 200Hz qhov tseem ceeb zaus. Tus cab kuj yog ib tug mem tes nthwv dej nrog 5kHz zaus.
➢ Cov kauj ruam:

Teem lub zaus, amplitude thiab offset ntawm cov cab kuj yoj.
1. Nias Waveforms , thiab xaiv Pulse waveform raws li cov cab kuj yoj
2. Nias zaus / Lub Sij Hawm thiab xaiv Zaus uas yuav tso tawm xim xiav. Cov tswv yim '5' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teeb tsa zaus rau 5kHz
3. Xovxwm Amplitude/HighLevel thiab xaiv Amplitude uas yuav tso saib xiav xim. Nkag mus '5' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp' los teeb tsa amplus 5vp.
4. Nias Offset/LowLevel thiab xaiv Offset uas yuav tso saib xim xiav. Nkag mus '0' los ntawm cov keyboard thiab xaiv chav tsev 'Vdc' los teeb qhov offset rau 0Vdc.
5. Nias PulWidth/DutyCycle thiab xaiv PulWidth uas yuav tso saib xim xiav. Nkag mus '40' los ntawm cov keyboard thiab xaiv chav tsev 'peb' los teeb tsa PulWidth rau 40us
Teem lub modulation hom PWM thiab tsis.
1. Nias Mod , Thov ceeb toom tias cov lus qhia nyob rau nruab nrab sab laug ntawm lub vijtsam yog 'PWM'.
2. Nias PWM Freq, input '200' los ntawm cov keyboard thiab xaiv chav tsev 'Hz' los teeb lub PWM Freq rau 200Hz.
3. Nias Dav Dev, nkag '20' los ntawm cov keyboard thiab xaiv chav tsev 'peb' los teeb tsa qhov dav sib txawv rau 20us

Thaum tag nrho cov ntsuas saum toj no tau teeb tsa, lub waveform generated yog qhia hauv daim duab 3-15.

3.16ex ibample 16: Tsim DSB-AM Modulation Waveform
Tsim ib DSB-AM modulation waveform nrog 100Hz modulating zaus. Cov cab kuj yog sine wave nrog 2kHz zaus.
➢ Cov kauj ruam:

Teem lub zaus, amplitude thiab offset ntawm cov cab kuj yoj.
1. Nias Waveforms , thiab xaiv cov sine waveform raws li cov cab kuj yoj.
2. Nias zaus / Lub Sij Hawm thiab xaiv Zaus uas yuav tso tawm xim xiav. Cov tswv yim '2' los ntawm cov keyboard thiab xaiv chav tsev 'kHz' los teeb tsa zaus rau 2kHz
3. Xovxwm Amplitude/HighLevel thiab xaiv Amplitude uas yuav tso saib xiav xim. Nkag mus '4' los ntawm cov keyboard thiab xaiv chav tsev 'Vpp' los teeb tsa amplus 4vp.
4. Nias Offset/LowLevel thiab xaiv Offset uas yuav tso saib xim xiav. Nkag mus '0' los ntawm cov keyboard thiab xaiv chav tsev 'Vdc' los teeb qhov offset rau 0Vdc.
Teem lub modulation hom DSB-AM thiab tsis.
1. Nias Mod → Hom → DSB-AM , xaiv DSB-AM. Thov nco ntsoov tias cov lus qhia nyob rau nruab nrab sab laug ntawm lub vijtsam yog 'DSB-AM'.
2. Nias DSB Freq, input '100' los ntawm cov keyboard thiab xaiv chav tsev 'Hz' los teem lub DSB Freq rau 100Hz.

Thaum tag nrho cov ntsuas saum toj no tau teeb tsa, lub waveform generated yog qhia hauv daim duab 3-16.

Kev daws teeb meem

4.1 Kev soj ntsuam dav dav
Tom qab tau txais ib qho tshiab SDG2000X Series Function / Arbitrary Generator thov tshuaj xyuas cov ntsuas raws li hauv qab no:

Tshawb xyuas lub thawv xa khoom kom puas.
Khaws lub thawv xa khoom puas lossis cov khoom siv cushioning kom txog thaum cov khoom xa tuaj tau raug kuaj xyuas kom tiav thiab cov cuab yeej tau raug kuaj xyuas cov tshuab thiab hluav taws xob.
Tshawb xyuas tag nrho cov cuab yeej.
Nyob rau hauv rooj plaub uas muaj ib qho kev puas tsuaj los yog tsis xws luag, los yog lub twj paj nruag tsis ua hauj lwm zoo los yog ua tsis tiav nyob rau hauv qhov kev xeem, ceeb toom rau SIGLENT tus neeg muag khoom.
Yog tias lub thawv xa khoom puas lawm, lossis cov ntaub ntawv cushioning qhia tias muaj kev ntxhov siab, ceeb toom rau tus neeg nqa khoom nrog rau SIGLENT chav muag khoom. Khaws cov khoom xa tuaj rau cov neeg nqa khoom kuaj xyuas.
Kos rau lub accessories.
Cov khoom siv nrog cov cuab yeej tau teev nyob rau hauv "Appendix A". Yog tias cov ntsiab lus tsis tiav lossis puas, ceeb toom rau SIGLENT tus neeg muag khoom.

4.2 Troubleshooting

Tom qab lub tshuab hluav taws xob qhib, yog tias lub vijtsam tseem tsaus, thov ua raws li cov kauj ruam hauv qab no:
1) Tshawb xyuas lub hwj chim cable kev sib txuas.
2) Xyuas kom lub hwj chim hloov tau qhib.
3) Tom qab kev tshuaj xyuas saum toj no, rov pib lub tshuab hluav taws xob.
4) Yog tias lub tshuab hluav taws xob tseem tsis ua haujlwm tom qab kuaj xyuas, thov hu rau SIGLENT.
Yog tias tsis muaj qhov tso tawm waveform tom qab teeb tsa qhov ntsuas, thov ua raws li cov kauj ruam hauv qab no:
1) Xyuas seb BNC cable puas muaj kev sib txuas zoo rau qhov chaw tso zis.
2) Xyuas seb cov yuam sij tso zis puas tau qhib lawm.
3) Yog tias lub tshuab hluav taws xob tseem tsis ua haujlwm tom qab kuaj xyuas, thov hu rau SIGLENT.

Kev Pabcuam thiab Kev Pabcuam

5.1 Cov ntsiab lus ntawm kev saib xyuas
SIGLENT tau lees paub tias cov khoom uas nws tsim thiab muag yuav tsis muaj qhov tsis xws luag hauv cov ntaub ntawv thiab kev ua haujlwm rau peb xyoos txij li hnub xa khoom los ntawm tus neeg muag khoom tso cai SIGLENT.
Yog tias cov khoom raug pov thawj tias muaj kev puas tsuaj nyob rau lub sijhawm lav, SIGLENT yuav muab kev kho lossis hloov lub tsev raws li tau piav qhia hauv daim ntawv lees paub tiav.
Txhawm rau npaj rau kev pabcuam lossis tau txais ib daim qauv ntawm daim ntawv lees paub tiav, thov hu rau koj lub chaw muag khoom thiab pabcuam SIGLENT ze tshaj plaws. Tsuas yog raws li tau hais hauv cov ntsiab lus no lossis daim ntawv lees paub siv tau, SIGLENT ua tsis muaj kev lav phib xaub ntawm txhua yam, qhia lossis qhia, suav nrog tab sis tsis txwv rau qhov kev lees paub ntawm kev ua lag luam thiab kev siv tshwj xeeb. Tsis muaj qhov tshwm sim yuav tsum SIGLENT yuav raug them rau kev puas tsuaj tsis ncaj, tshwj xeeb lossis qhov tshwm sim.

5.2 Hu rau SIGLENT
SIGLENT TECHNOLOGIES CO., LTD
Chaw nyob: 3/F, NO.4 lub tsev, Antongda Industrial Zone, 3rd Liuxian Road, 68th District, Baoan District, Shenzhen, PR Tuam Tshoj
Tel: 400-878-0807 Ib
E-mail: sales@siglent.com
http://www.siglent.com

Cov ntawv ntxiv

Daim Ntawv Ntxiv A: Accessories
SDG2000X Series Function/Arbitrary Waveform Generator Accessories:
Standard Accessories:

Phau Ntawv Qhia Pib Ceev
Daim Ntawv Qhia Calibration
Ib txoj hlua fais fab uas haum rau tus qauv ntawm lub teb chaws qhov chaw
Ib USB Cable
Ib qho BNC Coaxial Cable

Optional Accessories:

USB-GPIB adapter (IEEE 488.2)
SPA 1010 Lub Zog Ampua neej nyob
20 dB Attenuator

Daim Ntawv Ntxiv B: Kev tu thiab tu txhua hnub
Kev tu txhua hnub
Tsis txhob khaws lossis tso cov twj tso rau hauv qhov chaw uas lub vijtsam yuav raug tshav ntuj ncaj qha rau lub sijhawm ntev.
CEEB TOOM: Txhawm rau kom tsis txhob muaj kev puas tsuaj rau lub twj paj nruag, tsis txhob tso nws mus rau cov tshuaj tsuag, kua, los yog hnyav.

Ntxuav
Yog tias lub cuab yeej xav tau kev tu, tshem tawm ntawm txhua qhov chaw siv hluav taws xob thiab ntxuav nws nrog xab npum me me thiab dej. Xyuas kom tseeb tias qhov ntsuas tau qhuav tag ua ntej rov txuas nws mus rau lub zog hluav taws xob.
Txhawm rau ntxuav qhov chaw sab nrauv, ua cov kauj ruam hauv qab no:

Tshem cov plua plav xoob ntawm sab nraud ntawm lub ntsuas nrog ib daim ntaub tsis muaj lint. Thaum ntxuav lub vijtsam kov, ceev faj kom tsis txhob khawb lub pob tshab yas tiv thaiv npo.
Siv daim ntaub mos dampnrog dej los ntxuav lub ntsuas.

CEEB TOOM: Txhawm rau kom tsis txhob muaj kev puas tsuaj rau saum npoo ntawm lub cuab yeej, tsis txhob siv cov tshuaj abrasive lossis tshuaj ntxuav.

Hais txog SIGLENT
SIGLENT yog lub tuam txhab thev naus laus zis thoob ntiaj teb, tsom mus rau R & D, kev muag khoom, kev tsim khoom thiab kev pabcuam hluav taws xob kuaj & ntsuas ntsuas.
SIGLENT thawj zaug pib tsim cov oscilloscopes ntawm nws tus kheej hauv xyoo 2002.
Tom qab ntau tshaj li kaum xyoo ntawm kev txhim kho tas mus li, SIGLENT tau txuas ntxiv nws cov khoom lag luam kom suav nrog cov oscilloscopes, cais cov tes tuav oscilloscopes, kev ua haujlwm / kev ua haujlwm tsis txaus ntseeg, RF / MW teeb liab generators, spectrum analyzers, vector network analyzers, digital multimeters, DC fais fab mov, hluav taws xob loads thiab lwm yam kev ntsuas lub hom phiaj. Txij li thaum nws thawj oscilloscope tau tsim nyob rau hauv 2005, SIGLENT tau dhau los ua cov chaw tsim khoom loj tshaj plaws ntawm cov oscilloscopes. Peb ntseeg siab tias niaj hnub no SIGLENT yog tus nqi zoo tshaj plaws hauv kev ntsuas hluav taws xob & ntsuas.

Ua raws li peb
Facebook: SigentTech

https://www.facebook.com/SiglentTech

Lub hauv paus:
SIGLENT Technologies Co., Ltd
Ntxiv: Bldg No.4 & No.5, Antongda Industrial
Zone, 3rd Liuxian Road, Bao'an District,
Shenzhen, 518101, Suav
Tel: +86 755 3688 7876
Fax: + 86 755 3359 1582 XNUMX

North America:
SIGLENT Technologies America, Inc
6557 Cochran Rd Solon, Ohio 44139 (UA)
Tel: 440-398-5800 Ib
Tus Hu Dawb: 877-515-5551 Ib
Fax: 440-399-1211 Ib

Teb chaws Europe:
SIGLENT Technologies Lub teb chaws Yelemees GmbH
Ntxiv: Staetzlinger Str. 70
86165 Augsburg, Lub teb chaws Yelemees
T el: +49(0)-821-666 0 111 0
Fax: +49(0)-821-666 0 111 22

Cov ntaub ntawv / Cov ntaub ntawv

SIGLENT SDG2000X Series Function Arbitrary Waveform Generator [ua pdf] Tus neeg siv phau ntawv
SDG2000X Series Function Arbitrary Waveform Generator, SDG2000X Series, Muaj nuj nqi Arbitrary Waveform Generator, Arbitrary Waveform Generator, Waveform Generator, Generator

Cov ntaub ntawv

Cov neeg siv phau ntawv