NELSEN CHIP RO Controller System Controller Cov ntaub ntawv qhia phau ntawv

Table 1 – Specifications

Cov tswv yim
Tank theem hloov	(1) Nquag-Kaw. RO khiav ntawm kev kaw kaw.
Inlet siab hloov	Nquag-Qhib. Hloov qhib rau qhov tsis tshua muaj siab.
Pretreat lockout hloov	Nquag-Qhib. Pretreat lockout active nrog hloov kaw
	Nco tseg: Tag nrho cov hloov pauv inputs yog cov hu qhuav. Voltage siv rau qhov hloov pauv inputs yuav ua rau tus maub los puas
Maub los tswj fais fab	120 / 240 VAC, 60 / 50Hz (Ntau: 96-264 VAC)
	Lub switching fais fab mov cia li hloov mus rau mov voltage. Voltage thov rau cov tswv yim yog tib yam voltage lub cev muaj zog thiab li qub yuav ua haujlwm rau.
Output Relay Ratings
Pub Solenoid	12 A. Tso zis Voltage yog tib yam li lub cev muaj zog / khoom siv voltage.
Dej Solenoid	12 A. Tso zis Voltage yog tib yam li lub cev muaj zog / khoom siv voltage.
	Cov kev ntsuas ntawm solenoid relay saum toj no qhia txog lub peev xwm ntawm cov relays nkaus xwb. Tam sim no muaj peev xwm ntawm txhua lub voj voog yog 2A.
Tsav	1.0 TSI @ 120V 2.0 TSI @ 240V
Kev tiv thaiv Circuit Court
Controller Fais Fab Fuse	F1 x 5 mm	1/4 (0.25) Amp	Me Fuse 0218.250MXP
	Ceg tiv thaiv Circuit Court, lub cev muaj zog thiab valve tiv thaiv yuav tsum tau muab rau sab nraud
Lwm yam
Qhov ntev	7 "siab, 5" wide, 2.375" tob. Nema 4X Polycarbonate Enclosure
Qhov hnyav	1.1 lb ib.
Ib puag ncig	0-50 ° C, 10-90% RH (tsis-condensing)

Daim duab 1. Tus Tswj Tshajview

 Daim duab 2 - Tus Tswj Xyuas Kom Paub meej

Daim duab 3

Daim duab 4:

RO Program Settings
Hloov 1	Hloov 2	Program
OFF	OFF	1
ON	OFF	2
OFF	ON	3
ON	ON	4

Table 2 – Controller Programming: CHIP Program Selections

Tus maub los muaj 4 cais cov neeg siv-xaiv cov teeb tsa rau kev teeb tsa RO. Lub Hoobkas pib teeb tsa tau qhia hauv qab no. Cov kev teeb tsa zoo ib yam tshwj tsis yog kev hloov pauv hauv tus cwj pwm flush.

• Qhov program 1: High Pressure Flush
• Program 2: Tsis Muaj Flush
• Program 3: Permeate Flush, (tsis tshua muaj siab, inlet valve kaw)
• Program 4: Tsis tshua muaj siab, pub dej ntws tawm
• Saib nplooj ntawv dhau los rau cov lus qhia yuav ua li cas xaiv cov kev pab cuam no.
• Saib Daim Ntawv Ntxiv A rau cov lus piav qhia ntxaws txog Cov Tsis Muaj thiab lawv cuam tshuam rau RO txoj haujlwm.
• Saib Daim Ntawv Ntxiv B rau cov ntaub ntawv ntawm qhov programming interface siv los hloov kho cov chaw no.

Parameter	Tus nqi	Program 1	Program 2	Program 3	Program 4
Tank Level Hloov ncua (Actuation thiab de-actuation)	Thib ob	2	2	2	2
Pressure Switch ncua (actuation thiab de-actuation)	Thib ob	2	2	2	2
Pretreat Hloov ncua ncua sij hawm (actuation thiab de-actuation)	Thib ob	2	2	2	2
Pump pib qeeb	Thib ob	10	10	10	10
Inlet Solenid nres ncua	Thib ob	1	1	1	1
Pump start retry interval (restart ncua tom qab LP txhaum)	Thib ob	60	60	60	60
Tsawg siab yuam kev kaw, # ntawm faults	Ua txhaum	5	5	5	5
Tsis tshua muaj siab fault kaw, lub sij hawm rau suav faults	feeb	10	10	10	10
Tsawg siab yuam kev kaw, rov pib dua tom qab kaw	feeb	60	60	60	60
Tsawg siab lub sij hawm tawm txhaum	Thib ob	60	60	60	60
Flush Cwj Pwm	–	Siab Siab	Tsis muaj Flush	Perm Flush	Tsawg Pres Flush
Startup Flush: feeb los ntawm qhov dej ntws dhau los	feeb	0	0	0	0
Startup Flush: Duration	Thib ob	0	0	0	30
Periodic Flush: Lub sijhawm	feeb	60	0	0	0
Periodic Flush: Duration	Thib ob	30	0	0	0
Shutdown Flush: Sijhawm los ntawm qhov dej ntws dhau los	feeb	10	0	0	0
Shutdown Flush: Yam tsawg kawg nkaus	feeb	30	0	0	0
Shutdown Flush: Duration	Thib ob	60	0	60	60
Idle Flush: Lub sijhawm *	feeb	0	0	0	0
Idle Flush: Duration *	Thib ob	0	0	0	0

• Cov yam ntxwv no yog neeg xiam oob qhab los ntawm lub neej ntawd vim muaj peev xwm tsis meej pem ntawm ib feem ntawm cov neeg siv kawg hauv thaj teb. Lawv tuaj yeem qhib tau thaum xav tau los ntawm OEM PC programming interface uas tso cai rau kev hloov pauv rau tag nrho cov txiaj ntsig tau qhia saum toj no.

Daim Ntawv Ntxiv C – Controller Limited Warranty

Qhov kev tiv thaiv npog dab tsi:
CHIP tau lees paub tias tsis muaj qhov tsis zoo ntawm cov khoom siv thiab kev ua haujlwm thaum lub sijhawm lav. Yog tias ib yam khoom ua pov thawj tias muaj teeb meem thaum lub sijhawm lav, Nelsen Corporation yuav ntawm nws qhov kev xaiv kho lossis hloov cov khoom nrog cov khoom zoo li. Hloov cov khoom lossis cov khoom yuav suav nrog cov khoom siv rov ua dua tshiab lossis rov ua dua tshiab lossis cov khoom siv.

Lub warranty siv sijhawm ntev npaum li cas:
CHIP tau lav rau ib (1) xyoo rau cov khoom thiab kev ua haujlwm txij li hnub thawj cov neeg siv khoom yuav khoom lossis 15 lub hlis txij li hnub nkoj nkoj, qhov twg los ua ntej.

Dab tsi lub warranty tsis them:

1. Kev puas tsuaj, deterioration los yog malfunction los ntawm:
   1.  Kev siv tsis raug, kev tsis saib xyuas, hluav taws kub, dej xob laim lossis lwm yam kev ua ntawm qhov xwm txheej, kev hloov kho cov khoom tsis raug tso cai lossis tsis ua raws li cov lus qhia muab rau cov khoom.
   2. Kho lossis sim kho los ntawm leej twg tsis tau tso cai los ntawm Nelsen Corporation.
   3. Kev puas tsuaj ntawm cov khoom vim kev xa khoom.
   4. Ua rau sab nraud rau cov khoom xws li hluav taws xob hloov pauv.
   5. Kev siv cov khoom siv lossis cov khoom tsis ua raws li i-Controls ' specifications.
   6. Ib txwm hnav thiab tsim kua muag.
   7. Lwm qhov laj thawj uas tsis cuam tshuam nrog cov khoom tsis raug.
2. Cov nqi tsheb thauj mus los tsim nyog kom tau txais kev pabcuam raws li qhov kev lees paub no.
3. Ua hauj lwm tshaj li lub Hoobkas ua hauj lwm.

Yuav ua li cas thiaj tau txais kev pabcuam:

1. Yuav kom tau txais kev pab cuam warranty, hu rau koj tus neeg muag khoom muag rau Daim Ntawv Tso Cai Rov Qab (RMA).
2. Koj yuav tsum tau muab:
   1. Koj lub npe thiab chaw nyob
   2. Kev piav qhia ntawm qhov teeb meem
3.  Ntim tus maub los ua tib zoo rau kev xa khoom thiab xa rov qab rau koj, freight prepaid.

Txwv tsis pub muaj kev lav phib xaub:
Tsis muaj kev lav phib xaub, qhia lossis qhia, uas txuas ntxiv tshaj li cov lus piav qhia hauv no suav nrog kev lees paub ntawm kev ua lag luam thiab kev nyab xeeb rau ib lub hom phiaj tshwj xeeb.
Kev cais tawm ntawm kev puas tsuaj:
Kev lav phib xaub yog txwv rau tus nqi kho lossis hloov cov khoom. Nelsen Corporation yuav tsis lav rau:

1. Kev puas tsuaj rau lwm yam khoom uas tshwm sim los ntawm ib qho tsis xws luag hauv cov khoom, kev puas tsuaj raws li kev tsis txaus siab, kev siv cov khoom siv, kev siv lub sijhawm, kev poob nyiaj, kev poob haujlwm, kev poob siab, kev cuam tshuam kev lag luam lossis lwm yam kev lag luam poob, txawm hais tias tau qhia txog qhov ua tau lossis kev puas tsuaj.
2. Lwm yam kev puas tsuaj, txawm li cas los xij, qhov tshwm sim los yog lwm yam.
3. Ib qho kev thov tawm tsam tus neeg siv khoom los ntawm lwm tus neeg sab nrauv.

Cov nyhuv ntawm lub xeev txoj cai:
Qhov kev lees paub no muab cov cai tshwj xeeb rau koj, thiab koj tuaj yeem muaj lwm txoj cai uas txawv ntawm lub xeev mus rau ib lub xeev. Qee lub xeev tsis tso cai txwv tsis pub muaj kev lav phib xaub thiab/lossis tsis pub cais tawm ntawm qhov xwm txheej lossis kev puas tsuaj, yog li cov kev txwv saum toj no thiab kev cais tawm yuav tsis siv rau koj.

 

Cov ntaub ntawv / Cov ntaub ntawv

	NELSEN CHIP RO Controller System Controller Cov ntaub ntawv [ua pdf] Phau ntawv qhia CHIP RO Controller System Cov Ntaub Ntawv Cov Ntaub Ntawv, CHIP RO, Cov Txheej Txheem Tswj Xyuas Cov Ntaub Ntawv
	NELSEN CHIP RO Controller System Controller Cov ntaub ntawv [ua pdf] Tus neeg siv phau ntawv CHIP RO Controller System Controller Documentation, CHIP RO, Controller System Controller Cov ntaub ntawv, Cov ntaub ntawv tswj xyuas, Cov ntaub ntawv

Cov ntaub ntawv

• Cov neeg siv phau ntawv