Módulos de memoria DDR4
“
Especificacións
| Tipo de memoria | DDR4 Desktop Memory (Unbuffered) |
|---|---|
| Capacidades Dispoñibles | 8GB, 16GB (Single Module) |
| Frecuencias dispoñibles | 2666 MHz, 3200 MHz, 3600 MHz |
| Voltage | 1.2 V |
| Configuración de pin | 288 pinos |
| Corrección de erros | Non-ECC Unbuffered |
| Rexistrado | Si |
| CAS de latencia | CL21 (depending on frequency) |
| Factor de forma | DIMM (módulo de memoria dual en liña) |
| Esparcidor de calor | Aluminum heat spreader |
Compatibilidade
Desktop motherboards with DDR4 slots.
Compoñentes compatibles
Recommended Motherboards:
- Intel 600, 500, and 400 series chipsets (Z690, B660, H610,
Z590, B560, etc.) - AMD 500 and 400 series chipsets (X570, B550, X470, B450,
etc.) - Older chipsets that support DDR4 memory
Recommended Processors:
- Intel Core i3, i5, i7, i9 processors (10th, 11th, 12th, 13th
Xer) - AMD Ryzen 3, 5, 7, 9 processors (3000, 4000, 5000 series)
Configuración da memoria
Para un rendemento óptimo:
- Install memory in pairs for dual-channel operation (check
motherboard manual for correct slots) - For best results, use identical memory modules with same
capacity and frequency - Enable XMP/D.O.C.P. in BIOS to achieve advertised speeds
Nota: Higher frequency memory (3600MHz) may
require a more recent CPU and motherboard to achieve full speed.
Always check your motherboard’s QVL (Qualified Vendor List) for
compatibilidade.
Guía de instalación
- Aviso: Always handle memory modules by the
edges. Avoid touching the gold contacts or components on the
circuit board. Static electricity can damage the memory, so use an
anti-static wrist strap when handling components. - 1. Power Down the System
Shut down the computer completely and disconnect all power cables
da fonte de alimentación. - 2. Open the Computer Case
Remove the side panel of your computer case to access the
placa base. - 3. Locate Memory Slots
Identify the memory slots on your motherboard. Consult your
motherboard manual for optimal slot population order (usually slots
2 and 4 for dual channel). - 4. Release Retention Clips
Open the retention clips at both ends of the memory slot by pushing
them outward. - 5. Align the Memory Module
Align the notch in the memory module with the key in the memory
slot to ensure proper orientation. - 6. Install the Memory
Firmly press down on the memory module until the retention clips
snap into place automatically. - 7. Repeat for Additional Modules
If installing multiple modules, repeat the process for each module,
following the motherboard’s recommended population sequence. - 8. Close the System
Replace the computer case panel, reconnect all cables, and power on
o sistema. - Nota: After installing new memory, enter the
system BIOS/UEFI to verify that all memory is detected and enable
XMP/D.O.C.P. to achieve the advertised speed.
Preguntas frecuentes (FAQ)
Q: Can I mix different capacities of KLLISRE Desktop DDR4
Memory modules?
A: While it is possible to mix different capacities, it is
recommended to use identical memory modules for optimal
rendemento.
Q: Is it necessary to enable XMP/D.O.C.P. in BIOS after
installing KLLISRE Desktop DDR4 Memory?
A: Enabling XMP/D.O.C.P. in BIOS is recommended to achieve the
advertised speeds of the memory modules.
"'
KLLISRE Desktop DDR4 Memory
Manual de usuario e guía de instalación Descargar como documento de Word
Produto rematadoview
KLLISRE Desktop DDR4 Memory modules are designed for high-performance computing, offering excellent speed and reliability for gaming, content creation, and everyday computing tasks. These modules feature sleek heat spreaders for improved thermal performance and stability.
Especificacións
Especificación Tipo de memoria Capacidades dispoñibles Frecuencias dispoñibles Vol.tage Pin Configuration Error Correction Registered CAS Latency Form Factor Heat Spreader
Details DDR4 Desktop Memory (Unbuffered) 8GB,16GB (Single Module) 2666MHZ, 3200MHz, 3600MHz 1.2V 288-pin Non-ECC Unbuffered CL21 (depending on frequency) DIMM (Dual In-line Memory Module) Yes, aluminum heat spreader
Compatibilidade
Desktop motherboards with DDR4 slots
Compoñentes compatibles
Placas base recomendadas
KLLISRE Desktop DDR4 Memory is compatible with a wide range of desktop motherboards:
Intel 600, 500, and 400 series chipsets (Z690, B660, H610, Z590, B560, etc.)
AMD 500 and 400 series chipsets (X570, B550, X470, B450, etc.) Older chipsets that support DDR4 memory
Procesadores recomendados
This memory works with both Intel and AMD platforms:
Intel Core i3, i5, i7, i9 processors (10th, 11th, 12th, 13th Gen)
AMD Ryzen 3, 5, 7, 9 processors (3000, 4000, 5000 series)
Configuración da memoria
Para un rendemento óptimo:
Install memory in pairs for dual-channel operation (check motherboard manual for correct slots)
For best results, use identical memory modules with same capacity and frequency
Enable XMP/D.O.C.P. in BIOS to achieve advertised speeds
Note: Higher frequency memory (3600MHz) may require a more recent CPU and motherboard to achieve full speed. Always check your motherboard’s QVL (Qualified Vendor List) for compatibility.
Guía de instalación
Warning: Always handle memory modules by the edges. Avoid touching the gold contacts or components on the circuit board. Static electricity can damage the memory, so use an anti-static wrist strap when handling components. 1 Power Down the System Shut down the computer completely and disconnect all power cables from the power supply.
2 Open the Computer Case Remove the side panel of your computer case to access the motherboard.
3 Locate Memory Slots Identify the memory slots on your motherboard. Consult your motherboard manual for optimal slot population order (usually slots 2 and 4 for dual channel).
4 Liberación dos clips de retención Abra os clips de retención en ambos extremos da ranura de memoria empuxándoos cara a fóra.
5 Aliñe o módulo de memoria Aliñe a muesca do módulo de memoria coa chave da ranura de memoria para garantir unha orientación correcta.
6 Instale a memoria Prema firmemente o módulo de memoria ata que os clips de retención encaixen no seu lugar automaticamente.
7 Repita para módulos adicionais Se instala varios módulos, repita o proceso para cada módulo, seguindo a secuencia de poboamento recomendada pola placa base.
8 Close the System Replace the computer case panel, reconnect all cables, and power on the system.
Note: After installing new memory, enter the system BIOS/UEFI to verify that all memory is detected and enable XMP/D.O.C.P. to achieve the advertised speed.
Resolución de problemas
O sistema non arranca despois da instalación
Possible causes: Improperly seated memory, incompatible memory, BIOS needs update.
Solutions: Reseat memory modules, clear CMOS, update motherboard BIOS to latest version.
Só se detectou memoria parcial
Posibles causas: memoria incorrectamente instalada, poboamento de memoria incompatible, ranura de memoria defectuosa.
Solucións: Reinstalar os módulos de memoria, consultar o manual da placa base para coñecer a orde de poboamento correcta e probar os módulos en diferentes ranuras.
Memory Not Running at Advertised Speed (3200/3600MHz)
Why this happens: By default, DDR4 memory runs at a conservative JEDEC standard speed (usually 2133MHz or 2400MHz). To achieve the advertised higher speeds, you must enable the XMP (Extreme Memory Profile) for Intel systems or D.O.C.P. (Direct Overclock Profile) for AMD systems in the BIOS.
Other reasons: Some older CPUs or motherboards may not support higher memory speeds. The memory controller in your CPU has limitations, and motherboard topology can affect maximum achievable speed.
Solucións:
1. Enter BIOS/UEFI settings during boot (usually by pressing DEL or F2)
2. Find memory settings (often under “Advanced” or “Overclocking” menu)
3. Enable XMP (Intel) or D.O.C.P. (AMD)
4. Select the appropriate profile for your memory speed
5. Save changes and exit BIOS
6. If system becomes unstable, update BIOS to latest version
7. If problems persist, you may need to manually set speed and timings
Inestabilidade ou fallos do sistema
Posibles causas: configuracións de temporización da memoria incompatibles, sobrequecemento, enerxía insuficiente.
Solutions: Load BIOS optimized defaults, ensure proper system cooling, verify power supply adequacy, test with one module at a time.
Blue Screen Errors
Possible causes: Memory compatibility issues,Processor incompatibility, incorrect timings.
Solutions: Test each module individually, run memory diagnostic tools (Windows Memory Diagnostic or MemTest86), adjust BIOS memory settings.
Nota: Se os problemas persisten, probe cada módulo de memoria individualmente para identificar posibles módulos defectuosos. Póñase en contacto co servizo de asistencia de KLLISRE se sospeita que o produto é defectuoso.
Información da garantía
KLLISRE Desktop DDR4 Memory modules are covered by one year warranty. The warranty covers defects in materials and workmanship under normal use. Proof of purchase is required for warranty service.
Para reclamacións de garantía ou asistencia técnica, póñase en contacto co servizo de asistencia de KLLISRE cos detalles da súa compra e unha descrición do problema.
Esta garantía non cobre os danos resultantes de accidentes, mal uso, abuso, instalación incorrecta ou modificacións non autorizadas.
2023 KLLISRE. All rights reserved. KLLISRE is a registered trademark. Specifications are subject to change without notice.
Documentos/Recursos
 |
KLLISRE DDR4 Memory Modules [pdfManual do usuario DDR4 Memory Modules, DDR4, Memory Modules, Modules |