Mòduls de memòria DDR4
“
Especificacions
| Tipus de memòria | DDR4 Desktop Memory (Unbuffered) |
|---|---|
| Capacitats disponibles | 8GB, 16GB (Single Module) |
| Freqüències disponibles | 2666 MHz, 3200 MHz, 3600 MHz |
| Voltage | 1.2 V |
| Configuració del pin | 288 pins |
| Correcció d'errors | Non-ECC Unbuffered |
| Registrat | Sí |
| Latència CAS | CL21 (depending on frequency) |
| Factor de forma | DIMM (mòdul de memòria dual en línia) |
| Escampador de calor | Aluminum heat spreader |
Compatibilitat
Desktop motherboards with DDR4 slots.
Components compatibles
Recommended Motherboards:
- Intel 600, 500, and 400 series chipsets (Z690, B660, H610,
Z590, B560, etc.) - AMD 500 and 400 series chipsets (X570, B550, X470, B450,
etc.) - Older chipsets that support DDR4 memory
Recommended Processors:
- Intel Core i3, i5, i7, i9 processors (10th, 11th, 12th, 13th
Gen) - AMD Ryzen 3, 5, 7, 9 processors (3000, 4000, 5000 series)
Configuració de la memòria
Per obtenir un rendiment òptim:
- Install memory in pairs for dual-channel operation (check
motherboard manual for correct slots) - For best results, use identical memory modules with same
capacity and frequency - Enable XMP/D.O.C.P. in BIOS to achieve advertised speeds
Nota: Higher frequency memory (3600MHz) may
require a more recent CPU and motherboard to achieve full speed.
Always check your motherboard’s QVL (Qualified Vendor List) for
compatibilitat.
Guia d'instal·lació
- Avís: Always handle memory modules by the
edges. Avoid touching the gold contacts or components on the
circuit board. Static electricity can damage the memory, so use an
anti-static wrist strap when handling components. - 1. Power Down the System
Shut down the computer completely and disconnect all power cables
de la font d'alimentació. - 2. Open the Computer Case
Remove the side panel of your computer case to access the
placa base. - 3. Locate Memory Slots
Identify the memory slots on your motherboard. Consult your
motherboard manual for optimal slot population order (usually slots
2 and 4 for dual channel). - 4. Release Retention Clips
Open the retention clips at both ends of the memory slot by pushing
them outward. - 5. Align the Memory Module
Align the notch in the memory module with the key in the memory
slot to ensure proper orientation. - 6. Install the Memory
Firmly press down on the memory module until the retention clips
snap into place automatically. - 7. Repeat for Additional Modules
If installing multiple modules, repeat the process for each module,
following the motherboard’s recommended population sequence. - 8. Close the System
Replace the computer case panel, reconnect all cables, and power on
el sistema. - Nota: After installing new memory, enter the
system BIOS/UEFI to verify that all memory is detected and enable
XMP/D.O.C.P. to achieve the advertised speed.
Preguntes freqüents (FAQ)
Q: Can I mix different capacities of KLLISRE Desktop DDR4
Memory modules?
A: While it is possible to mix different capacities, it is
recommended to use identical memory modules for optimal
rendiment.
Q: Is it necessary to enable XMP/D.O.C.P. in BIOS after
installing KLLISRE Desktop DDR4 Memory?
A: Enabling XMP/D.O.C.P. in BIOS is recommended to achieve the
advertised speeds of the memory modules.
"`
KLLISRE Desktop DDR4 Memory
Manual d'usuari i guia d'instal·lació Descarregar com a document de Word
Producte acabatview
KLLISRE Desktop DDR4 Memory modules are designed for high-performance computing, offering excellent speed and reliability for gaming, content creation, and everyday computing tasks. These modules feature sleek heat spreaders for improved thermal performance and stability.
Especificacions
Especificació Tipus de memòria Capacitats disponibles Freqüències disponibles Volumtage Pin Configuration Error Correction Registered CAS Latency Form Factor Heat Spreader
Details DDR4 Desktop Memory (Unbuffered) 8GB,16GB (Single Module) 2666MHZ, 3200MHz, 3600MHz 1.2V 288-pin Non-ECC Unbuffered CL21 (depending on frequency) DIMM (Dual In-line Memory Module) Yes, aluminum heat spreader
Compatibilitat
Desktop motherboards with DDR4 slots
Components compatibles
Plaques base recomanades
KLLISRE Desktop DDR4 Memory is compatible with a wide range of desktop motherboards:
Intel 600, 500, and 400 series chipsets (Z690, B660, H610, Z590, B560, etc.)
AMD 500 and 400 series chipsets (X570, B550, X470, B450, etc.) Older chipsets that support DDR4 memory
Processadors recomanats
This memory works with both Intel and AMD platforms:
Intel Core i3, i5, i7, i9 processors (10th, 11th, 12th, 13th Gen)
AMD Ryzen 3, 5, 7, 9 processors (3000, 4000, 5000 series)
Configuració de la memòria
Per obtenir un rendiment òptim:
Install memory in pairs for dual-channel operation (check motherboard manual for correct slots)
For best results, use identical memory modules with same capacity and frequency
Enable XMP/D.O.C.P. in BIOS to achieve advertised speeds
Note: Higher frequency memory (3600MHz) may require a more recent CPU and motherboard to achieve full speed. Always check your motherboard’s QVL (Qualified Vendor List) for compatibility.
Guia d'instal·lació
Warning: Always handle memory modules by the edges. Avoid touching the gold contacts or components on the circuit board. Static electricity can damage the memory, so use an anti-static wrist strap when handling components. 1 Power Down the System Shut down the computer completely and disconnect all power cables from the power supply.
2 Open the Computer Case Remove the side panel of your computer case to access the motherboard.
3 Locate Memory Slots Identify the memory slots on your motherboard. Consult your motherboard manual for optimal slot population order (usually slots 2 and 4 for dual channel).
4 Alliberament dels clips de retenció Obriu els clips de retenció dels dos extrems de la ranura de memòria empenyent-los cap a fora.
5 Alineeu el mòdul de memòria Alineeu l'osca del mòdul de memòria amb la clau de la ranura de memòria per garantir una orientació correcta.
6 Instal·leu la memòria Premeu fermament el mòdul de memòria fins que els clips de retenció encaixin automàticament al seu lloc.
7 Repetiu per a mòduls addicionals Si instal·leu diversos mòduls, repetiu el procés per a cada mòdul, seguint la seqüència d'ompliment recomanada per la placa base.
8 Close the System Replace the computer case panel, reconnect all cables, and power on the system.
Note: After installing new memory, enter the system BIOS/UEFI to verify that all memory is detected and enable XMP/D.O.C.P. to achieve the advertised speed.
Resolució de problemes
El sistema no arrenca després de la instal·lació
Possible causes: Improperly seated memory, incompatible memory, BIOS needs update.
Solutions: Reseat memory modules, clear CMOS, update motherboard BIOS to latest version.
Només s'ha detectat memòria parcial
Possibles causes: memòria mal instal·lada, ocupament de memòria incompatible, ranura de memòria defectuosa.
Solucions: Torneu a col·locar els mòduls de memòria, consulteu el manual de la placa base per conèixer l'ordre correcte d'ompliment i proveu els mòduls en ranures diferents.
Memory Not Running at Advertised Speed (3200/3600MHz)
Why this happens: By default, DDR4 memory runs at a conservative JEDEC standard speed (usually 2133MHz or 2400MHz). To achieve the advertised higher speeds, you must enable the XMP (Extreme Memory Profile) for Intel systems or D.O.C.P. (Direct Overclock Profile) for AMD systems in the BIOS.
Other reasons: Some older CPUs or motherboards may not support higher memory speeds. The memory controller in your CPU has limitations, and motherboard topology can affect maximum achievable speed.
Solucions:
1. Enter BIOS/UEFI settings during boot (usually by pressing DEL or F2)
2. Find memory settings (often under “Advanced” or “Overclocking” menu)
3. Enable XMP (Intel) or D.O.C.P. (AMD)
4. Select the appropriate profile for your memory speed
5. Save changes and exit BIOS
6. If system becomes unstable, update BIOS to latest version
7. If problems persist, you may need to manually set speed and timings
Inestabilitat o bloquejos del sistema
Causes possibles: Configuració de temporització de memòria incompatible, sobreescalfament, energia insuficient.
Solutions: Load BIOS optimized defaults, ensure proper system cooling, verify power supply adequacy, test with one module at a time.
Blue Screen Errors
Possible causes: Memory compatibility issues,Processor incompatibility, incorrect timings.
Solutions: Test each module individually, run memory diagnostic tools (Windows Memory Diagnostic or MemTest86), adjust BIOS memory settings.
Nota: Si els problemes persisteixen, proveu cada mòdul de memòria individualment per identificar possibles mòduls defectuosos. Poseu-vos en contacte amb el suport tècnic de KLLISRE si sospiteu que el producte és defectuós.
Informació de la garantia
KLLISRE Desktop DDR4 Memory modules are covered by one year warranty. The warranty covers defects in materials and workmanship under normal use. Proof of purchase is required for warranty service.
Per a reclamacions de garantia o assistència tècnica, poseu-vos en contacte amb el servei d'assistència de KLLISRE amb els detalls de la vostra compra i una descripció del problema.
Aquesta garantia no cobreix els danys resultants d'accidents, mal ús, abús, instal·lació incorrecta o modificacions no autoritzades.
2023 KLLISRE. All rights reserved. KLLISRE is a registered trademark. Specifications are subject to change without notice.
Documents/Recursos
 |
KLLISRE DDR4 Memory Modules [pdfManual d'usuari DDR4 Memory Modules, DDR4, Memory Modules, Modules |