DDR4 модули памет
“
Спецификации
| Тип памет | DDR4 Desktop Memory (Unbuffered) |
|---|---|
| Налични капацитети | 8GB, 16GB (Single Module) |
| Налични честоти | 2666MHz, 3200MHz, 3600MHz |
| Voltage | 1.2V |
| Конфигурация на пин | 288-пинов |
| Корекция на грешки | Non-ECC Unbuffered |
| Регистриран | да |
| CAS закъснение | CL21 (depending on frequency) |
| Форма фактор | DIMM (Двуредов модул памет) |
| Разпределител на топлина | Aluminum heat spreader |
Съвместимост
Desktop motherboards with DDR4 slots.
Съвместими компоненти
Recommended Motherboards:
- Intel 600, 500, and 400 series chipsets (Z690, B660, H610,
Z590, B560, etc.) - AMD 500 and 400 series chipsets (X570, B550, X470, B450,
и т.н.) - Older chipsets that support DDR4 memory
Recommended Processors:
- Intel Core i3, i5, i7, i9 processors (10th, 11th, 12th, 13th
Gen) - AMD Ryzen 3, 5, 7, 9 processors (3000, 4000, 5000 series)
Конфигурация на паметта
За оптимално представяне:
- Install memory in pairs for dual-channel operation (check
motherboard manual for correct slots) - For best results, use identical memory modules with same
capacity and frequency - Enable XMP/D.O.C.P. in BIOS to achieve advertised speeds
Забележка: Higher frequency memory (3600MHz) may
require a more recent CPU and motherboard to achieve full speed.
Always check your motherboard’s QVL (Qualified Vendor List) for
съвместимост.
Ръководство за инсталиране
- Предупреждение: Always handle memory modules by the
edges. Avoid touching the gold contacts or components on the
circuit board. Static electricity can damage the memory, so use an
anti-static wrist strap when handling components. - 1. Power Down the System
Shut down the computer completely and disconnect all power cables
от захранването. - 2. Open the Computer Case
Remove the side panel of your computer case to access the
дънна платка. - 3. Locate Memory Slots
Identify the memory slots on your motherboard. Consult your
motherboard manual for optimal slot population order (usually slots
2 and 4 for dual channel). - 4. Release Retention Clips
Open the retention clips at both ends of the memory slot by pushing
them outward. - 5. Align the Memory Module
Align the notch in the memory module with the key in the memory
slot to ensure proper orientation. - 6. Install the Memory
Firmly press down on the memory module until the retention clips
snap into place automatically. - 7. Repeat for Additional Modules
If installing multiple modules, repeat the process for each module,
following the motherboard’s recommended population sequence. - 8. Close the System
Replace the computer case panel, reconnect all cables, and power on
системата. - Забележка: After installing new memory, enter the
system BIOS/UEFI to verify that all memory is detected and enable
XMP/D.O.C.P. to achieve the advertised speed.
Често задавани въпроси (FAQ)
Q: Can I mix different capacities of KLLISRE Desktop DDR4
Memory modules?
A: While it is possible to mix different capacities, it is
recommended to use identical memory modules for optimal
изпълнение.
Q: Is it necessary to enable XMP/D.O.C.P. in BIOS after
installing KLLISRE Desktop DDR4 Memory?
A: Enabling XMP/D.O.C.P. in BIOS is recommended to achieve the
advertised speeds of the memory modules.
„`
KLLISRE Desktop DDR4 Memory
Ръководство за потребителя и ръководство за инсталиране Изтегляне като Word документ
Продуктът е свършилview
KLLISRE Desktop DDR4 Memory modules are designed for high-performance computing, offering excellent speed and reliability for gaming, content creation, and everyday computing tasks. These modules feature sleek heat spreaders for improved thermal performance and stability.
Спецификации
Спецификация Тип памет Налични капацитети Налични честоти Обемtage Pin Configuration Error Correction Registered CAS Latency Form Factor Heat Spreader
Details DDR4 Desktop Memory (Unbuffered) 8GB,16GB (Single Module) 2666MHZ, 3200MHz, 3600MHz 1.2V 288-pin Non-ECC Unbuffered CL21 (depending on frequency) DIMM (Dual In-line Memory Module) Yes, aluminum heat spreader
Съвместимост
Desktop motherboards with DDR4 slots
Съвместими компоненти
Препоръчани дънни платки
KLLISRE Desktop DDR4 Memory is compatible with a wide range of desktop motherboards:
Intel 600, 500, and 400 series chipsets (Z690, B660, H610, Z590, B560, etc.)
AMD 500 and 400 series chipsets (X570, B550, X470, B450, etc.) Older chipsets that support DDR4 memory
Препоръчителни процесори
This memory works with both Intel and AMD platforms:
Intel Core i3, i5, i7, i9 processors (10th, 11th, 12th, 13th Gen)
AMD Ryzen 3, 5, 7, 9 processors (3000, 4000, 5000 series)
Конфигурация на паметта
За оптимално представяне:
Install memory in pairs for dual-channel operation (check motherboard manual for correct slots)
For best results, use identical memory modules with same capacity and frequency
Enable XMP/D.O.C.P. in BIOS to achieve advertised speeds
Note: Higher frequency memory (3600MHz) may require a more recent CPU and motherboard to achieve full speed. Always check your motherboard’s QVL (Qualified Vendor List) for compatibility.
Ръководство за инсталиране
Warning: Always handle memory modules by the edges. Avoid touching the gold contacts or components on the circuit board. Static electricity can damage the memory, so use an anti-static wrist strap when handling components. 1 Power Down the System Shut down the computer completely and disconnect all power cables from the power supply.
2 Open the Computer Case Remove the side panel of your computer case to access the motherboard.
3 Locate Memory Slots Identify the memory slots on your motherboard. Consult your motherboard manual for optimal slot population order (usually slots 2 and 4 for dual channel).
4 Освободете скобите за задържане Отворете скобите за задържане в двата края на слота за памет, като ги натиснете навън.
5 Подравнете модула памет Подравнете жлеба в модула памет с ключа в слота за памет, за да осигурите правилната ориентация.
6 Инсталирайте паметта. Натиснете здраво модула памет, докато скобите за задържане щракнат автоматично на мястото си.
7 Повторете за допълнителни модули Ако инсталирате няколко модула, повторете процеса за всеки модул, следвайки препоръчителната последователност на инсталиране на дънната платка.
8 Close the System Replace the computer case panel, reconnect all cables, and power on the system.
Note: After installing new memory, enter the system BIOS/UEFI to verify that all memory is detected and enable XMP/D.O.C.P. to achieve the advertised speed.
Отстраняване на неизправности
Системата не се стартира след инсталирането
Possible causes: Improperly seated memory, incompatible memory, BIOS needs update.
Solutions: Reseat memory modules, clear CMOS, update motherboard BIOS to latest version.
Открита е само частична памет
Възможни причини: Неправилно поставена памет, несъвместима памет, дефектен слот за памет.
Решения: Преинсталирайте модулите памет, вижте ръководството за дънната платка за правилния ред на поставяне, опитайте модулите в различни слотове.
Memory Not Running at Advertised Speed (3200/3600MHz)
Why this happens: By default, DDR4 memory runs at a conservative JEDEC standard speed (usually 2133MHz or 2400MHz). To achieve the advertised higher speeds, you must enable the XMP (Extreme Memory Profile) for Intel systems or D.O.C.P. (Direct Overclock Profile) for AMD systems in the BIOS.
Other reasons: Some older CPUs or motherboards may not support higher memory speeds. The memory controller in your CPU has limitations, and motherboard topology can affect maximum achievable speed.
Решения:
1. Enter BIOS/UEFI settings during boot (usually by pressing DEL or F2)
2. Find memory settings (often under “Advanced” or “Overclocking” menu)
3. Enable XMP (Intel) or D.O.C.P. (AMD)
4. Select the appropriate profile for your memory speed
5. Save changes and exit BIOS
6. If system becomes unstable, update BIOS to latest version
7. If problems persist, you may need to manually set speed and timings
Нестабилност или сривове на системата
Възможни причини: Несъвместими настройки за синхронизация на паметта, прегряване, недостатъчно захранване.
Solutions: Load BIOS optimized defaults, ensure proper system cooling, verify power supply adequacy, test with one module at a time.
Blue Screen Errors
Possible causes: Memory compatibility issues,Processor incompatibility, incorrect timings.
Solutions: Test each module individually, run memory diagnostic tools (Windows Memory Diagnostic or MemTest86), adjust BIOS memory settings.
Забележка: Ако проблемите продължават, тествайте всеки модул памет поотделно, за да идентифицирате потенциални дефектни модули. Свържете се с поддръжката на KLLISRE, ако подозирате дефектен продукт.
Гаранционна информация
KLLISRE Desktop DDR4 Memory modules are covered by one year warranty. The warranty covers defects in materials and workmanship under normal use. Proof of purchase is required for warranty service.
За гаранционни рекламации или техническа поддръжка, моля, свържете се с поддръжката на KLLISRE, като предоставите данните за покупката си и описание на проблема.
Тази гаранция не покрива щети, причинени от злополука, неправилна употреба, злоупотреба, неправилен монтаж или неоторизирани модификации.
2023 KLLISRE. All rights reserved. KLLISRE is a registered trademark. Specifications are subject to change without notice.
Документи / Ресурси
 |
KLLISRE DDR4 Memory Modules [pdf] Ръководство за потребителя DDR4 Memory Modules, DDR4, Memory Modules, Modules |