Introduction
The STI STI-9764-R Horn/Strobe Damage Stopper is a robust, red, wall-mounted protective cage designed to safeguard horn/strobe units from accidental damage, vandalism, or tampering. This device is ideal for use in public areas, schools, hospitals, and other environments where fire safety equipment needs additional protection. Its durable construction ensures long-lasting performance and reliable protection for critical alarm components.
Safety Information
- Always disconnect power to the horn/strobe unit before installation or maintenance of the damage stopper.
- Ensure all mounting hardware is securely fastened to prevent the unit from falling.
- Do not obstruct the horn/strobe unit's sound or light output with the damage stopper. Ensure proper clearance.
- This product is designed for protection; it does not replace proper installation or maintenance of the horn/strobe unit itself.
- Consult local building codes and fire safety regulations for proper installation requirements.
Package Contents
Verify that all components are present before beginning installation:
- 1 x STI STI-9764-R Horn/Strobe Damage Stopper (Red)
- Mounting Hardware (screws, wall anchors) - (Note: Specific hardware may vary, ensure suitable fasteners for your wall type are used)
- Installation Guide (this manual)
Setup and Installation
Follow these steps for proper installation of the damage stopper:
- Prepare the Mounting Surface: Identify a suitable wall location that provides adequate support for the damage stopper and the horn/strobe unit. Ensure the surface is clean and free of obstructions.
- Position the Damage Stopper: Hold the damage stopper in the desired position over the horn/strobe unit. Ensure the unit is fully enclosed and there is sufficient clearance for its operation. Mark the drilling points through the mounting holes on the damage stopper.
- Drill Pilot Holes: Using an appropriate drill bit for your wall type, drill pilot holes at the marked locations. If installing into drywall, insert wall anchors as needed.
- Secure the Damage Stopper: Align the damage stopper with the drilled holes. Insert the provided mounting screws (or suitable alternatives) through the mounting holes and tighten them securely. Do not overtighten.
- Verify Installation: Gently tug on the installed damage stopper to ensure it is firmly attached to the wall and does not wobble. Confirm that the horn/strobe unit is protected and its functionality is not impaired.
Image: The STI STI-9764-R Horn/Strobe Damage Stopper, a red wire cage designed for wall mounting to protect horn/strobe units.
Operating Instructions
The STI STI-9764-R is a passive protective device. It does not require any operational steps once installed. Its function is to provide a physical barrier against impact and tampering for the horn/strobe unit it encloses. Ensure the horn/strobe unit itself is operating correctly according to its own manufacturer's instructions.
Maintenance
The damage stopper requires minimal maintenance:
- Cleaning: Periodically wipe the surface of the damage stopper with a soft, damp cloth to remove dust and dirt. Avoid abrasive cleaners that could damage the finish.
- Inspection: Regularly inspect the damage stopper and its mounting hardware for any signs of loosening, damage, or corrosion. Tighten any loose screws immediately.
- Damage Assessment: If the damage stopper sustains significant impact or shows signs of structural compromise, it should be replaced to ensure continued protection of the horn/strobe unit.
Troubleshooting
As a passive device, the damage stopper has limited troubleshooting scenarios:
| Problem | Possible Cause | Solution |
|---|---|---|
| Damage stopper is loose on the wall. | Mounting screws are loose or wall anchors are failing. | Tighten mounting screws. If necessary, remove, repair wall, and re-install with appropriate anchors. |
| Horn/strobe unit is still being damaged. | Damage stopper is improperly installed or insufficient for the type of impact. | Verify proper installation. Consider if a more robust protective solution is required for the environment. |
| Damage stopper is bent or broken. | Sustained significant impact. | Replace the damage stopper immediately to ensure continued protection. |
Specifications
| Attribute | Detail |
|---|---|
| Model Number | STI-9764-R (SSTI9764R) |
| Brand | STI |
| Product Type | Horn/Strobe Damage Stopper |
| Mounting Type | Wall Mount |
| Color | Red |
| Material | Durable wire construction |
| UPC | 662950018124 |
| Date First Available | May 31, 2023 |
Warranty and Support
For information regarding warranty coverage and technical support for your STI STI-9764-R Horn/Strobe Damage Stopper, please contact STI directly through their official website or customer service channels. Keep your purchase receipt as proof of purchase for any warranty claims.
Manufacturer: STI
Website: www.sti-usa.com (Note: This is a general placeholder for a manufacturer's website. Please refer to the product packaging or official STI documentation for the most accurate contact information.)
