ERP Programming Software
Amanothi Okukhishwa Kwethuluzi Lokucushwa Komshayeli

I-ERP Programming Software Driver Configuration Tool

Inguqulo 2.1.1 (19 Okthoba 2022)

1. Kubuyekezwe ukucushwa okuzenzakalelayo.
2. Kwengezwe amamanyuwali omsebenzisi kufolda yemibhalo.
3. Kwengezwe ukulungiswa kwabanye abashayeli ukuze kulungiswe ukuziphatha kokuchezuka kokwakhiwa.
4. Kungezwe isheke leluphu evaliwe kanye neluphu evulekile PKB/PKM. Izolungisa ngokuzenzakalela noma iyiphi iluphu evuliwe noma izishayeli zeluphu evaliwe ezilungiselelwe ngezilungiselelo zeluphu ephambene.
5. Ukufanisa ukulungiselelwa kuzosebenzisa inombolo yemodeli yeqiniso ngaphandle kwezijobelelo zasembonini ezifihliwe kuphela, noma inombolo yemodeli ebonisiwe. Lokhu kuvimbela ukumiswa kwe-lot ukuthi kungami uma umshayeli othi “-A” noma “-DN” exhunyiwe.
6. Ayikho ibhakhodi ekhona noma ibhakhodi engavumelekile okutholwe kuyo phakathi nemodi yokumisa inkatho manje ezokwengeza isibali sokumisa inkatho, kodwa isakhipha isexwayiso.
7. Ayikho ibhakhodi ekhona noma ibhakhodi engavumelekile ekhona manje ohlwini lomphumela wokuhlela njengokuthi “Isexwayiso” ohlwini lokucushwa kwenkatho, kunokuthi “Iphutha.”
8. Ukufaniswa kwebhokisi lenhlanganisela ye-Lot config kungasebenzisa inombolo yemodeli ebonisiwe, noma inombolo yemodeli egcwele ukuze ifane. Imizamo yokufanisa inombolo yemodeli ebonisiwe kuqala.
9. Kwengezwe ukusekelwa okufanele kwe-STM32L16x bootloader.
10. Kukhishwe iwindi le-popup ye-bootloader elinephutha, eyala ngokungalungile iyunithi ukuthi inikeze amandla umjikelezo weyunithi ebuyekezwayo.

Inguqulo 2.0.9 (14 May 2021)

1. Kwengezwe ukuhleleka kwe-NTC yochungechunge lwe-PKM.
2. Izinto zemenyu yokucushwa ye-NTC elungisiwe lapho ukufiphala okulungisekayo kanye nomshayeli we-NTC olungisekayo kuxhunyiwe.
3. Kwengezwe inkinobho yokuguqula ukuze kushintshwe viewnge-NTC profile igrafu kanye ne-dimmer profile igrafu.
4. Ukwesekwa okwengeziwe kwenkumbulo enkulu ye-FW updates.
5. Isikali se-DPI esilungisiwe se-TRIAC, 0-10 V kanye negrafu ye-NTC views.
6. Igrafu e-dimmer elungisiwe ethinta indawo yoqobo engu-0,0 ngisho noma i-dim to off ivaliwe.

Inguqulo 2.0.8 (09 Okthoba 2020)

1. Kwengezwe ukuhambisana kwe-PTB/PKB/PKM.
2. Umbhalo webha eseceleni manje usuyakwazi ukukhetha igundane ukuze ukopishe kalula ulwazi.
3. Kwengezwe umbhalo wephrinta ye-zebra uma umbhalo weqa ububanzi benkambu.
4. Thuthukisa ukusebenza kwe-Firmware yeyunithi manje ingasebenzisa izindlela zenethiwekhi.
5. Kwengezwe izinkambu ezinekhodi ezinombala ze-TRIAC/ELV zama-engeli ama-conduction aphezulu naphansi ukuze kucace okubonakalayo.
6.  Kwengezwe ukulungiswa okuzenzakalelayo kwe-PKB/PKM/PTB ehlelwe ngezibuyekezo zangaphambili ze-GUI.
7. Kwengezwe amandla okuchaza umbala wetimu nesithombe sesibhengezo ngombhalo file, CustomerColors.txt.
8. Kwengezwe izinhlamvu ze-Windows ezingekho emthethweni hlola ukuze ungene file isizukulwane samagama.
9. Ukulungiswa kweziphazamisi okuhlukahlukene nokuthuthukiswa kokuzinza

Inguqulo 2.0.7 (15 January 2020)

1. Kwengezwe ukuhambisana kwe-VZM, voltagI-e iku-mV, hhayi ama-volts aphelele.
2. Kwengezwe ukuvikelwa kwephasiwedi kumodi yokuklama.
3. Inkinga elungisiwe lapho amamodeli e-DAL kanye ne-CNB-SIL engeke ahlele kahle.
4. Ukususwa okugxilile kwamadijithi amabili okugcina ochungechungeni lwe-FW.
5. Inkinga elungisiwe lapho amanani amaminithi angu-0-10 V e-setpoint angaphansi kuka-0.7 V engeke abonakale ngendlela efanele.
6. Kushintshwe i-min dim ukuze ivale i-hysteresis ibe ngu-0.01 V.
7. Kushintshwe osayizi besinyathelo sokusethwa kwe-dimmer ukuze babe ngu-0.01 V.
8. Kushintshwe iphoyinti le-dimmer min ubuncane ukuze libe ngu-0 V, umkhawulo usetshenziselwa ukufiphala ukuya endaweni.
9. Kushintshwe ukuziphatha kokuqedela inkatho uma okuphindiwe kutholakele.
10. Inkinga exazululiwe lapho umshayeli oyimpinda noma wephutha engakhulisa ikhawunta yokumisa inkatho uma bekungumshayeli wokugcina endaweni.
11. I-GUI manje ayinaki -S noma -T lapho ifanelana nemodi yokumisa inkatho.
12. Kwengezwe amandla okulungiselela okukude. Ukucushwa kwesilawuli kude kufundwa kuphela.
13. Amandla wendlela yenethiwekhi ye-SMB engeziwe yokucushwa okukude nefolda yelogi ye-csv.
14. I-popup yephasiwedi yemodi yokukhiqiza/yokudizayina manje isiyiwindi le-popup, esikhundleni sengxoxo Ivumela ukhiye wekhibhodi, ukuze isebenze kahle uma ufaka iphasiwedi. Kwengezwe i-8.7V max dimmer voltage kuya kuzilungiselelo ze-GUI zamamodeli Ahlukanisiwe. Izingxenyekazi zekhompyutha azikwazi ukusekela amanani e-dimmer angaphezu kuka-8.7V, iyunithi ingase ingafinyeleli okukhiphayo okungu-100% uma ihlelwe ngaphezu kuka-8.7V.
15. Ukusebenza kwe-NTC kukhutshaziwe ngaphandle kwamamodeli angayisekeli.

Inguqulo 2.0.6 (12 Juni 2019)

1. Lapho kwethulwa i-GUI, kunikezwa izindlela ezimbili: Imodi Yokukhiqiza kanye Nemodi Yokuklama. I-Design Mode inikeza abasebenzisi ukulawula okugcwele kwe-GUI. Imodi Yokukhiqiza ivumela kuphela ukuhlelwa kwenqwaba futhi igodla amandla okudala ukulungiselelwa komshayeli okusha. Nquma, engeza ukulungisa, thuthukisa i-firmware, futhi susa izinkinobho zokumisa kufihlwe Kumodi Yokukhiqiza.
2. Kwengezwe ukuhambisana kwe-NFC.
3.  Amaphutha wokuhlela nezixwayiso azisanciphisi isibali senkatho.
4. Ihlukanisa phakathi kwephutha ezindabeni zezinhlelo nebhakhodi, izinkinga zebhakhodi zibonisa isikrini sokubuyekeza esiphuzi, amaphutha ohlelo abonisa isikrini sokubuyekeza esibomvu.
5. Kwengezwe ivolumu engaguqukitage ukucushwa windows ukusetshenziswa VZM series.
6.  Kwengezwe isikrini solwazi ukwazisa umsebenzisi uma umshayeli ehlelwa.
7. Indawo yelogi ye-CSV iyaqhubeka ize ishintshwe umsebenzisi.
8. Inkinga elungisiwe yokudala ukucushwa okungenalutho noma okuyimpinda lapho ungenisa ukucushwa file.

Inguqulo 2.0.5 (25 January 2019) 

1. Kwengezwe i-dimming curve profile okukhethiwe kwe-1% ngokucisha futhi ngaphandle kokufiphala; 10% ngokuvala futhi ngaphandle kokufiphala; Ijika lokufiphala elijwayelekile le-ESS; kanye ne-ANSI dimming curve. Lapho uxhuma abashayeli be-PSB50-40-30 abakhiqizwe ngokubuyekezwa C, umuntu manje angakhetha phakathi kwalokhu okulandelayo okungu-8 okuchazwe ngaphambilini kwe-0-10V dimming pro.files:
   • 1% ubuncane bokufiphalisa ngokufiphalisa ukuya kokucisha
   • 1% ubuncane bokufiphalisa ngaphandle kokufiphalisa ukuya kokucisha
   • 10% ubuncane bokufiphalisa ngokufiphalisa ukuya kokucisha
   • 10% ubuncane bokufiphalisa ngaphandle kokufiphalisa ukuya kokucisha
   • I-Logarithmic
   • I-ANSI C137.1: ifana nokufiphala okuncane okungu-1% ngokufiphala kuya kokucisha kodwa ngevelu ehlukile ye-ditto-off
   • Umugqa we-ESS: ufana ne-linear profile isetshenziswe ochungechungeni lwe-ESS/ESST, ESP/ESPT ne-ESM
   • Kuyahleleka – umsebenzisi uchaziwe: Wonke amaphuzu kule profile ihlelwa ngokugcwele ngumsebenzisi
   Abashayeli be-PSB50-40-30 abakhiqizwe noma ngemva kweviki 50 lika-2018 bathunyelwa “no-1% ubuncane bokufiphalisa ngokufiphala kokuya ku-off” 0-10V profile njenge-pro ezenzakalelayofile. Sicela uqaphele ukuthi, lapho uxhuma abashayeli be-PSB50-40-30 abakhiqizwe ngokubuyekezwa A noma B, umuntu angakhetha kuphela okulandelayo oku-4 okuchazwe ngaphambilini okungu-0-10V dimming pro.files:
   • I-Logarithmic
   • I-ANSI C137.1
   • Umugqa we-ESS
   • Kuyahleleka – kuchazwe umsebenzisi
2. Ukwesekwa okwengeziwe kokuphrinta ilebula; futhi wengeze inkinobho yokuphinda uzame ukuphrinta esimweni lapho ilebula ingaphrintwa ngemva kokuhlelwa okuyimpumelelo komshayeli.
3. Kulungiswe ukususwa ngephutha kwakho konke ukulungiselelwa uma okuthi "Susa Ukukhetha" kuchofozwe kabili efasiteleni Lokukhetha Ukucushwa. I-Delete config manje ine-popup yewindi yokuqinisekisa.
4. Kwengezwe ukulungiselelwa komshayeli we-PMB Series.
5. Amaphesenti angeziwetagkuya kumapharamitha we-dimmer yebha eseceleni lapho kusetshenziswa amajika okufiphalisa ahlelekayo.
6. Kwengezwe indawo yefolda Yokucushwa Kwelogi ekhethiwe njengamanje ekucushweni kwesitoko view.
7. Kwengezwe inkinobho ukushintsha indawo yefolda yokucushwa kwelogi.
8. Inkinobho ethi “Lungisa Uhlelo Lomshayeli” ivaliwe kuze kube yilapho ukulungiselelwa komshayeli sekufundwe ngokugcwele.
9. Uma isizindalwazi Sokucushwa Kwenkatho sinokufana nemodeli exhunywe manje, ithebula Lokucushwa Kwenkatho lizokhetha ngokuzenzakalelayo leyo modeli.
10. Imilayezo yesimo se-GUI (ngezansi kwesokunxele kwesikrini), manje bonisa ukuthi i-GUI yenzani njengamanje. Ibonisa uma ufunda kumshayeli, uhlela umshayeli, futhi ufuna umshayeli.
11. Qamba Kabusha Inkinobho Yokumisa manje isisebenza ngokugcwele esikrinini Sokucushwa Kwenqwaba. Umsebenzisi angachofoza inkinobho, noma achofoze kabili ukulungiselelwa, okumnikeza inketho yokuqamba kabusha incazelo yokucushwa.
12. Isheke elengeziwe lamabhakhodi ayimpinda atholiwe, igcina wonke amabhakhodi ahlelwe endaweni eqhubekayo eqhubekayo ehlelwayo.
13. Kwengezwe ukuqinisekiswa kokufunda ngemuva kokuhlela umshayeli kumodi ye-Lot Programming; uma wonke amapharamitha afundeka emuva afanayo, ilebula njenge-pass in log file.
14.  Ilogi ye-Lot Programming Enwetshiwe file ukufaka u-100% wawo wonke amapharamitha ahleliwe
15. Kwengezwe isheke lebhakhodi engenalutho noma ezenzakalelayo kumodi ye-Lot Programming.
16. Inkinobho eyengeziwe yokuhlela inkambu yencazelo Ekucushweni Kwenkatho.
17. I-Lot Programming izoqala kabusha ngokuzenzakalela ngemva kokuthi umshayeli wemodeli engalungile exhunywe.
18. Kushintshwe inkambu yebha eseceleni engu-0-10V ukuze ifake kuhlu ivolumu ye-dimmertages.

Inguqulo 2.0.4

1. Akuyona inguqulo ekhishwe esidlangalaleni Yethuluzi Lokulungiselela Umshayeli

Inguqulo 2.0.3 (01 Okthoba 2018)

1. I-GUI ibuyekeza ngokuzenzakalelayo umshayeli, ekuxhumekeni, uma ithola ngaphandle kobubanzi noma amabhayithi edatha eyonakele. Ububanzi bamanani amukelekayo asethiwe.
2. Ukusebenza okuthuthukisiwe kwe-TRIAC kwabashayeli be-PHB Series.
3. Kwengezwe umsebenzi wokuphrinta ilebula.
4. I-0-10V kanye ne-TRIAC Min Out zonke ziphathwa nge-% esikhundleni se-mV.
5. Inkinobho yokuhlela inkatho engaguquki ehlela umshayeli ongu-1.
6. Kwengezwe igrafu yokusebenza kwe-NTC.
7. Kwengezwe 0-10V kanye nencazelo yokusebenza ye-TRIAC kubha eseceleni.
8. Vula isifunda voltage kanye nevolumu encanetage ayisaboniswa ngokusekelwe kumpendulo yomsebenzisi.

Inguqulo 1.1.1 (12 Agasti 2018)

1. Kulungiswe iphutha lapho umsebenzi wokudlulisa we-TRIAC (PHB Series kuphela), ubulungiswa ngevelu efanayo nomsebenzi wokudlulisa ongu-0-10V.

Inguqulo 1.1.0 (02 Julayi 2018)

1. Kwengezwe amapharamitha we-NTC kuwo wonke amapharamitha files kufaka phakathi uhlu lokucushwa.
2. Kwengezwe ilogi ye-csv file ukulungiswa, okulungela ukuthi ifolda yedatha ye-ERP isuswe.
3. Izinkinobho zokumisa zokungenisa/thumela ohlangothini lwesokudla.
4. I-GUI ehlanganisiwe phakathi kwe-PSB Series ne-PDB Series.

Amadokhumenti / Izinsiza

I-ERP POWER ERP Programming Software Driver Configuration Tool [pdf] Umhlahlandlela Womsebenzisi I-ERP Programming Software Driver Configuration Tool, ERP, Programming Software Driver Configuration Tool, Software Driver Configuration Tool, Configuration Tool

Izithenjwa

• Imaniwali yosebenzisayo