Sensọ otutu Wifi WS1
“
Awọn pato ọja
| Awoṣe | Ibi ti ina elekitiriki ti nwa | Max lọwọlọwọ | Iwọn Iwọn | Yiye | Ipinnu | Ipele Idaabobo | Asopọmọra | USB Ipari | Ilana ibaraẹnisọrọ | RS485 adirẹsi | Oṣuwọn Baud |
|---|---|---|---|---|---|---|---|---|---|---|---|
| UB-aaya-N1 | DC 4.5 ~ 30V | — | soil+60%+25) EC: 1S/cm Temperature: 0.1 Humidity: 0.1% | — | — | IP68 | Ohun | 3m | RS485 Modbus RTU Ilana | 0xD6 | 1200 bit/s, 2400 bit/s, 4800 bit/s (default), 9600 bit/s, 19200 bps |
Awọn ilana Lilo ọja
Agbegbe wiwọn
Measurement area: Inside a 5cm diameter cylinder of equal height
to the probes, centered on the center of the two probes.
Ilẹ ilaluja Ọna
Ni inaro ma wà iho kan pẹlu iwọn ila opin ti> 20cm. Fi sii
pin sensọ nâa sinu ogiri ọfin ni ijinle ti iṣeto
and fill the pit tightly. After a period of stabilization,
wiwọn ati awọn gbigbasilẹ le ṣee ṣe ni akoko ti awọn ọjọ,
months, or even longer.
Awọn Ilana Ibaraẹnisọrọ
1. Ibaraẹnisọrọ Ipilẹ paramita
- Ifaminsi System Data Bit
- Parity Checking Bit Stop Bit Error Checking Baud Rate 1200
bit/s, 2400 bit/s, 4800 bit/s (default), 9600 bit/s, 19200
bps
2. Data fireemu kika
Ilana ibaraẹnisọrọ Modbus-RTU ti lo ni atẹle yii
ọna kika:
- Ni ibẹrẹ be: 4 baiti ni akoko.
- Address code: 1 byte, default 0xE1.
- Koodu iṣẹ: 1 baiti, koodu iṣẹ atilẹyin 0x03 (ka nikan)
ati 0x06 (ka / kọ). - Agbegbe data: N awọn baiti, data 16-bit, baiti giga wa akọkọ.
- Ṣayẹwo aṣiṣe: koodu CRC 16-bit.
- Opin be: 4 baiti ti akoko.
3. Forukọsilẹ adirẹsi
| Adirẹsi | Apejuwe |
|---|---|
| 0x0000 | Humidity (Unsigned integer data, divided by 10) |
| 0x0001 | Temperature (Signed integer data, divided by 10) |
| 0x0002 | EC Address Baud Rate Register Address Register Length Function Code (Integer 1255) |
AKIYESI:
- The probe must be fully inserted into the soil when
wiwọn. - Pay attention to lightning protection when using in the
aaye. - Do not violently bend the probe, do not pull the sensor lead
wire, do not drop or hit the sensor.
Awọn Ibeere Nigbagbogbo (FAQ)
Q: How deep should the sensor be inserted into the soil for
accurate measurements?
A: The sensor should be fully inserted into the
soil for accurate measurements.
Q: Njẹ sensọ le ṣee lo ni awọn agbegbe ita gbangba?
A: Yes, the sensor can be used in outdoor
environments. However, it is important to pay attention to
lightning protection when using it in the field.
Q: Kini ilana ibaraẹnisọrọ ti sensọ lo?
A: The sensor uses RS485 Modbus RTU Protocol
fun ibaraẹnisọrọ.
“`
Ọja Ifihan
The sensor, with its stable performance and high sensitivity, is an important tool for observing and studying the occurrence, evolution and improvement of saline soils and water-salt dynamics. Measurement of the dielectric constant of the soil provides a direct and stable reflection of the true water content of various soils, as well as a measurement of the volume percentage of soil moisture.
Use Case Scenarios The sensor is suitable for soil moisture monitoring, scientific experiments, water-saving irrigation, greenhouses, flowers and vegetables, meadows and pastures, rapid soil measurement, plant cultivation, wastewater treatment, fine agriculture and other occasions.
Features 1. Soil water content, conductivity and temperature in one. 2. Completely sealed, acid and alkali corrosion resistant, can be buried in the soil or directly into the
water for long-term dynamic detection. 3. High precision, fast response, good interchangeability, probe insertion design ensures accurate
measurement and reliable performance.
Awọn pato ọja
Ipese Agbara Awoṣe Iwọn Iwọn Iwọn lọwọlọwọ
Yiye
Resolution Protection level
Asopọ USB Ipari Communication Protocol RS485 adirẹsi
Oṣuwọn Baud
Awọn pato
UB-aaya-N1
DC 4.5 ~ 30V
110mA@5V EC: 0~20000S/cm Temperature: -40~80 Humidity: 0~100% EC: ±3%FS (0~10000S/cm), ±5%FS (10000~20000S/cm) Temperature: ±0.5 Humidity: ±2% (@0~50%, palm soil+30%+25) ; ±3% (@50~100%, palm
soil+60%+25) EC: 1S/cm
Temperature: 0.1 Humidity: 0.1% IP68
Ohun
3m
RS485 Modbus RTU Ilana
0xD6
1200 bit/s,2400 bit/s, 4800 bit/s (aiyipada), 9600 bit/s, 19200 bit/s
Ilana onirin
Measurement Area Measurement area: Inside a 5cm diameter cylinder of equal height to the probes, centred on the centre of the two probes.
Quick Test Method Select a suitable measurement site, avoid rocks and ensure that the steel needle does not touch hard objects. Throw away the top layer of soil according to the required measuring depth, keep the original tightness of the soil underneath, and insert the sensor vertically into the soil by holding it tightly. Do not shake the sensor from side to side when inserting it. It is recommended to take several measurements within a small area of one measurement point to find the average value.
Ground Penetration Method Vertically dig a pit with a diameter of >20cm. Insert the sensor pin horizontally into the pit wall at the established depth and fill the pit tightly. After a period of stabilisation, measurements and recordings can be made over a period of days, months or even longer.
Awọn ilana ibaraẹnisọrọ
1. Awọn ipilẹ ibaraẹnisọrọ ibaraẹnisọrọ
Ifaminsi System Data Bit
Parity Ṣiṣayẹwo Bit Duro Bit
Aṣiṣe Ṣiṣayẹwo Oṣuwọn Baud
Ibaraẹnisọrọ Ipilẹ paramita 8bit alakomeji 8 die-die kò 1 bit CRC Ṣayẹwo
1200 bit/s, 2400 bit/s, 4800 bit/s (aiyipada), 9600 bit/s, 19200 bit/s
2. Data fireemu kika
Ilana ibaraẹnisọrọ Modbus-RTU jẹ lilo ni ọna kika atẹle:
Ni ibẹrẹ be 4 baiti ni akoko.
Address code: 1 byte, default 0xE1.
Koodu iṣẹ: 1 baiti, koodu iṣẹ atilẹyin 0x03 (ka nikan) ati 0x06 (ka / kọ).
Agbegbe data: N awọn baiti, data 16-bit, baiti giga wa akọkọ.
Ṣayẹwo aṣiṣe: koodu CRC 16-bit.
Ipari be 4 baiti ti akoko.
Ibere
Ẹrú Adirẹsi
Adirẹsi iforukọsilẹ koodu iṣẹ No
CRC LSB
CRC MSB
1 baiti
1 baiti
2 baiti
2 baiti
1 baiti
1 baiti
Idahun
Koodu Iṣẹ-ṣiṣe Adirẹsi Ẹrú No. ti Awọn akoonu Baiti 1 Akoonu 1
…
Akoonu n
CRC
1 baiti
1 baiti
1 baiti
2 baiti
2 baiti
…
2 baiti
2 baiti
3. Forukọsilẹ adirẹsi
Address 0x0000 0x0001 0x0002 0x07D0 0x07D1
Content Humidity Temperature
EC Address Baud Rate
Forukọsilẹ Adirẹsi
Forukọsilẹ Ipari koodu koodu
1
03
1
03
1
03
1
03/06
1
03/06
Apejuwe awọn itumọ data odidi ti a ko fowo si, ti pin si 10
Signed integer data, divided by 10 Integer 1255
0:2400, 1:4800, 2:9600
NOTE 1. The probe must be fully inserted into the soil when measuring. 2. Pay attention to the lightning protection when using in the field. 3. Do not violently bend the probe, do not pull the sensor lead wire, do not drop or hit the sensor
ni agbara.
Awọn iwe aṣẹ / Awọn orisun
 |
UBiBOT WS1 Wifi Temperature Sensor [pdf] Itọsọna olumulo WS1, WS1 Pro, UB-SEC-N1, WS1 Wifi Temperature Sensor, WS1, Wifi Temperature Sensor, Temperature Sensor, Sensor |