TEXAS INSTRUMENTS CC1312PSIP SimpleLink Sub-1-GHz Alailowaya Eto-ninu-Package ti eni

Awọn agbeegbe asọye sọfitiwia; ifọwọkan capacitive, mita sisan,
LCD Low agbara agbara
Lilo MCU: – 2.9 mA ti nṣiṣe lọwọ mode, CoreMark ®
– 60 μA/MHz nṣiṣẹ CoreMark®
- Ipo imurasilẹ 0.9 μA, RTC, Ramu 80KB
- Ipo tiipa 0.1 μA, ji dide lori pin

Lilo agbara sensọ agbara kekere:
- 30 μA ni ipo 2-MHz
- 808 μA ni ipo 24-MHz
Lilo Redio:
- 5.8-mA RX ni 868 MHz
- 28.7-mA TX ni +14 dBm ni 868 MHz
Alailowaya Ilana support

Wi-SUN®
mioty®

Alailowaya M-Bus
SimpleLink™ TI 15.4-akopọ

6LoWPAN
Ohun-ini awọn ọna ṣiṣe Redio iṣẹ-giga

-119 dBm fun ipo-gigun 2.5-kbps
-108 dBm ni 50 kbps, 802.15.4, 868 MHz
Ibamu ilana

Ti jẹri tẹlẹ fun:
– FCC CFR47 Apa 15
Dara fun awọn eto ifọkansi ibamu pẹlu:
– ETSI EN 300 220 Ologbo olugba. 1.5 ati 2, EN 303 131, EN 303 204
- ARIB STD-T108
MCU pẹẹpẹẹpẹ

Awọn agbeegbe oni nọmba le jẹ ipalọlọ si 30 GPIOs
Mẹrin 32-bit tabi mẹjọ 16-bit gbogboogbo-idi awọn aago

12-bit ADC, 200 kSamples / s, 8 awọn ikanni
8-bit DAC

Meji comparators
Eto orisun lọwọlọwọ
UART meji, SSI meji, I
Aago gidi-akoko (RTC)
Iṣọkan otutu ati atẹle batiri
Awọn oluṣe aabo
AES 128- ati 256-bit cryptographic imuyara
ECC ati RSA àkọsílẹ bọtini hardware imuyara
SHA2 Accelerator (Suite kikun titi di SHA-512)
Olupilẹṣẹ nọmba ID otitọ (TRNG)
Awọn irinṣẹ idagbasoke ati sọfitiwia
LP-CC1312PSIP Idagbasoke Apo
SimpleLink™ CC13xx ati CC26xx Software
Apo Idagbasoke (SDK)
Studio SmartRF™ fun iṣeto redio ti o rọrun
Studio Adarí Sensọ fun kikọ awọn ohun elo oye agbara kekere
Ọpa iṣeto eto SysConfig
Iwọn iṣẹ
1.8-V to 3.8-V nikan ipese voltage
-40 si +105°C (+14 dBm PA)
Gbogbo pataki irinše ese
48-MHz gara: RF išedede ± 10 ppm

32-kHz gara: RTC išedede ± 50 ppm
DC/DC converter irinše ati decoupling capacitors
RF iwaju-opin irinše pẹlu 50-Ohm o wu
Package

7-mm × 7-mm MOT (30 GPIOs)
Pin-to-pin ni ibamu pẹlu CC2652RSIP ati CC2652PSIP
RoHS-ibaramu package

PATAKI AKIYESI ni opin iwe data yii awọn adirẹsi wiwa, atilẹyin ọja, awọn ayipada, lilo ninu awọn ohun elo to ṣe pataki aabo, awọn ọrọ ohun-ini imọ ati awọn ailabo pataki miiran. ALAYE Ilọsiwaju fun awọn ọja iṣaaju; koko ọrọ si ayipada lai akiyesi.

Awọn ohun elo

868 ati 902 si 928 MHz ISM ati awọn eto SRD 1 pẹlu isalẹ si 4 kHz ti bandiwidi gbigba
Adaṣiṣẹ ile
- Awọn ọna aabo ile - aṣawari išipopada, titiipa smati itanna, ilẹkun ati sensọ window, eto ilẹkun gareji, ẹnu-ọna
- HVAC – thermostat, sensọ ayika alailowaya, oluṣakoso eto HVAC, ẹnu-ọna
- Eto aabo ina - ẹfin ati aṣawari ooru, igbimọ iṣakoso itaniji ina (FACP)
– Fidio – Kamẹra nẹtiwọki IP
– Elevators ati escalators – elevator akọkọ Iṣakoso nronu fun elevators ati escalators

Akoj amayederun
- Awọn mita smart - mita omi, mita gaasi, mita ina, ati awọn ipin iye owo ooru
– Awọn ibaraẹnisọrọ Grid – awọn ibaraẹnisọrọ alailowaya – awọn ohun elo sensọ gigun-gun
- EV Gbigba agbara amayederun - AC gbigba agbara (opoplopo) ibudo
– Miiran yiyan agbara – agbara ikore
Irinna ile-iṣẹ – ipasẹ dukia
Automation Factory ati iṣakoso

Iṣoogun
Awọn ẹrọ ibaraẹnisọrọ
Nẹtiwọọki ti a firanṣẹ - LAN alailowaya tabi awọn aaye iwọle Wi-Fi, olulana eti

Apejuwe

Ẹrọ SimpleLink ™ CC1312PSIP jẹ System-in-Package (SiP) Sub-1 GHz module alailowaya ti n ṣe atilẹyin IEEE 802.15.4, awọn ohun ijafafa IPv6 (6LoWPAN), mioty, awọn eto ohun-ini, pẹlu TI 15.4-Stack. CC1312PSIP microcontroller (MCU) da lori ohun elo Arm M4F akọkọ ati iṣapeye fun ibaraẹnisọrọ alailowaya agbara kekere ati oye ilọsiwaju ninu awọn amayederun grid, adaṣe ile, adaṣe soobu ati awọn ohun elo iṣoogun. CC1312PSIP naa ni lọwọlọwọ oorun oorun ti 0.9 μA pẹlu RTC ati 80KB Ramu idaduro. Ni afikun si ero isise Cortex® M4F akọkọ, ẹrọ naa tun ni adase adase ultra-kekere sensọ Adarí Sipiyu pẹlu agbara jidide iyara. Bi example, awọn sensọ oludari ni o lagbara ti 1-Hz ADC sampling ni apapọ 1-μA eto lọwọlọwọ.
CC1312PSIP ni SER Kekere (Oṣuwọn Aṣiṣe Asọ) FIT (Ikuna-ni-akoko) fun igbesi aye ṣiṣe pipẹ. Ibaṣepọ SRAM ti o wa nigbagbogbo dinku eewu fun ibajẹ nitori awọn iṣẹlẹ itankalẹ ti o pọju. Ni ibamu pẹlu ọpọlọpọ awọn onibara 10 si ọdun 15 tabi awọn ibeere igbesi aye gigun, TI ni eto imulo igbesi-aye ọja kan pẹlu ifaramo si igbesi aye ọja ati ilosiwaju ti ipese pẹlu awọn ohun elo meji ti awọn eroja pataki ni SIP. Ẹrọ CC1312PSIP jẹ apakan ti SimpleLink™ MCU Syeed, eyiti o ni Wi-Fi®, Bluetooth® Low Energy, Thread, Zigbee, Wi-SUN®, Amazon Sidewalk, mioty, Sub-1 GHz MCUs, ati gbalejo MCUs. CC1312PSIP jẹ apakan ti portfolio ti o ni awọn SIPs 2.4-GHz pin-ibaramu fun irọrun ti ọja alailowaya si awọn iṣedede ibaraẹnisọrọ lọpọlọpọ. SimpleLink™ CC13xx ti o wọpọ ati CC26xx Ohun elo Idagbasoke sọfitiwia (SDK) ati ohun elo atunto eto SysConfig ṣe atilẹyin ijira laarin awọn ẹrọ inu portfolio. Nọmba okeerẹ ti awọn akopọ sọfitiwia, ohun elo examples ati awọn akoko ikẹkọ Ile-ẹkọ giga SimpleLink wa ninu SDK. Fun alaye diẹ sii, ṣabẹwo si Asopọmọra alailowaya.

PART NOMBA	Package	ÌWÉ ARA (NOM)
CC1312PSIPMOT	QFM	7.00 mm × 7.00 mm

(1) Fun apakan lọwọlọwọ julọ, package, ati alaye pipaṣẹ fun gbogbo awọn ẹrọ ti o wa, wo Afikun Aṣayan Package ni Mechanical, Packaging, ati Alaye Ti o paṣẹ, tabi wo TI webojula.
1 Wo Core RF fun awọn alaye ni afikun lori awọn iṣedede ilana atilẹyin, awọn ọna kika awose, ati awọn oṣuwọn data.

Aworan Àkọsílẹ iṣẹ

Àtúnyẹwò History

AKIYESI: Awọn nọmba oju-iwe fun awọn atunyẹwo iṣaaju le yatọ si awọn nọmba oju-iwe ni ẹya lọwọlọwọ.

DATE	Atunyẹwo	AKIYESI
Oṣu Karun-23	*	Itusilẹ akọkọ

Ifiwera ẹrọ

Iṣeto ni Pin ati Awọn iṣẹ

7.1 Pin aworan atọka – MOT Package (Oke View)
olusin 7-1. MOT (7-mm × 7-mm) Pinout, 0.5-mm Pitch (Oke View)

Awọn pinni I/O wọnyi ti a samisi ni Nọmba 7-1 ni igboya ni awọn agbara awakọ giga:

Pin 23, DIO_5
Pin 24, DIO_6
Pin 25, DIO_7

Pin 34, JTAG_TMSC
Pin 36, DIO_16
Pin 37, DIO_17

Awọn pinni I/O wọnyi ti o samisi ni Nọmba 7-1 ni awọn italics ni awọn agbara afọwọṣe:

Pin 1, DIO_26
Pin 2, DIO_27

Pin 3, DIO_28
Pin 7, DIO_29
Pin 8, DIO_30

Pin 44, DIO_23
Pin 45, DIO_24
Pin 48, DIO_25

7.2 Awọn apejuwe ifihan agbara - MOT Package
tabili 7-1. Awọn apejuwe ifihan – SIP Package

PIN		I/O	ORISI	Apejuwe
ORUKO	RARA.	I/O	ORISI	Apejuwe
NC	14	I/O	Oni-nọmba	Ko si Asopọmọra
DIO_1	21	I/O	Oni-nọmba	GPIO
DIO_10	28	I/O	Oni-nọmba	GPIO
DIO_11	29	I/O	Oni-nọmba	GPIO
DIO_12	30	I/O	Oni-nọmba	GPIO
DIO_13	31	I/O	Oni-nọmba	GPIO
DIO_14	32	I/O	Oni-nọmba	GPIO
DIO_15	33	I/O	Oni-nọmba	GPIO
DIO_16	36	I/O	Oni-nọmba	GPIO, JTAG_TDO, ga-drive agbara
DIO_17	37	I/O	Oni-nọmba	GPIO, JTAG_TDI, ga-drive agbara
DIO_18	39	I/O	Oni-nọmba	GPIO
DIO_19	40	I/O	Oni-nọmba	GPIO
DIO_2	20	I/O	Oni-nọmba	GPIO
DIO_20	41	I/O	Oni-nọmba	GPIO
DIO_21	42	I/O	Oni-nọmba	GPIO
DIO_22	43	I/O	Oni-nọmba	GPIO
DIO_23	44	I/O	Digital tabi Analog	GPIO, afọwọṣe agbara
DIO_24	45	I/O	Digital tabi Analog	GPIO, afọwọṣe agbara
DIO_25	48	I/O	Digital tabi Analog	GPIO, afọwọṣe agbara
DIO_26	1	I/O	Digital tabi Analog	GPIO, afọwọṣe agbara
DIO_27	2	I/O	Digital tabi Analog	GPIO, afọwọṣe agbara
DIO_28	3	I/O	Digital tabi Analog	GPIO, afọwọṣe agbara
DIO_29	7	I/O	Digital tabi Analog	GPIO, afọwọṣe agbara
NC	15	I/O	Oni-nọmba	Ko si Asopọmọra
DIO_30	8	I/O	Digital tabi Analog	GPIO, afọwọṣe agbara
PIO_31	38	I/O	Oni-nọmba	Ṣe atilẹyin iṣẹ agbeegbe nikan. Ko ṣe atilẹyin idi gbogbogbo I/O iṣẹ ṣiṣe.
DIO_4	22	I/O	Oni-nọmba	GPIO
DIO_5	23	I/O	Oni-nọmba	GPIO, ga-wakọ agbara
DIO_6	24	I/O	Oni-nọmba	GPIO, ga-wakọ agbara
DIO_7	25	I/O	Oni-nọmba	GPIO, ga-wakọ agbara
DIO_8	26	I/O	Oni-nọmba	GPIO
DIO_9	27	I/O	Oni-nọmba	GPIO
GND	5	—	—	GND
GND	9	—	—	GND
GND	10	—	—	GND
GND	11	—	—	GND
GND	12	—	—	GND
GND	13	—	—	GND
GND	16	—	—	GND
GND	17	—	—	GND
GND	19	—	—	GND
GND	49-73	—	—	GND

7.3 Awọn isopọ fun a ko lo awọn pinni ati modulu
tabili 7-2. Awọn isopọ fun a ko lo pinni

PIN		I/O	ORISI	Apejuwe
ORUKO	RARA.	I/O	ORISI	Apejuwe
NC	6	—	—	Ko si Asopọmọra
n RESET	4	I	Oni-nọmba	Tunto, ti nṣiṣe lọwọ kekere. Ti abẹnu pullup resistor ati ti abẹnu 100 nF to VDDS_PU
RF	18	—	RF	50 ohm RF ibudo
JTAG_TCKC	35	I	Oni-nọmba	JTAG_TCKC
JTAG_TMSC	34	I/O	Oni-nọmba	JTAG_TMSC, agbara awakọ giga
VDDS	46	—	Agbara	1.8-V to 3.8-V akọkọ SIP ipese
VDDS_PU	47	—	Agbara	Agbara lati tun ti abẹnu pullup resistor

Awọn pato

8.1 Idi ti o pọju-wonsi
lori iwọn otutu ti afẹfẹ ọfẹ ti nṣiṣẹ (ayafi bibẹẹkọ ṣe akiyesi) (1) (2)

			MIN	MAX	UNIT
VDDS(3)	Ipese voltage		–0.3	4.1	V
	Voltage lori eyikeyi oni nọmba (4)		–0.3	VDDS + 0.3, max 4.1	V
Vin	Voltage lori ADC igbewọle	Voltage igbelosoke ṣiṣẹ	–0.3	VDDS	V
		Voltage igbelosoke alaabo, ti abẹnu itọkasi	–0.3	1.49
		Voltage igbelosoke alaabo, VDDS bi itọkasi	–0.3	VDDS / 2.9
			10		dBm
Tstg	Ibi ipamọ otutu		–40	150	°C

Iṣiṣẹ ni ita Awọn iwọn-wonsi to pọju le fa ibajẹ ẹrọ titilai. Awọn iwontun-wonsi to gaju ko tumọ si iṣẹ ṣiṣe ẹrọ ni iwọnyi tabi awọn ipo miiran ju eyiti a ṣe akojọ labẹ Awọn ipo Iṣiṣẹ Iṣeduro. Ti o ba lo ni ita Awọn ipo Iṣiṣẹ ti a ṣeduro ṣugbọn laarin Awọn Iwọn Iwọn pipe to gaju, ẹrọ naa le ma ṣiṣẹ ni kikun, ati pe eyi le ni ipa lori igbẹkẹle ẹrọ, iṣẹ ṣiṣe, iṣẹ, ati kikuru igbesi aye ẹrọ naa.
Gbogbo voltage iye ni o wa pẹlu ọwọ si ilẹ, ayafi ti bibẹkọ ti woye.
VDDS_DCDC, VDDS2 ati VDDS3 gbọdọ wa ni agbara kanna bi VDDS.

Pẹlu afọwọṣe DIOs.

8.2 ESD-wonsi

				IYE	UNIT
VESD	Electrostatic itujade	Awoṣe ara eniyan (HBM), fun ANSI/ESDA/JEDEC JS-001(1)	Gbogbo awọn pinni	±1000	V
VESD	Electrostatic itujade	Awoṣe ẹrọ ti o gba agbara (CDM), fun ANSI/ESDA/JEDEC JS-002(2)	Gbogbo awọn pinni	±500	V

Iwe JEDEC JEP155 sọ pe 500-V HBM ngbanilaaye iṣelọpọ ailewu pẹlu ilana iṣakoso ESD boṣewa.

JEDEC iwe JEP157 sọ pe 250-V CDM ngbanilaaye iṣelọpọ ailewu pẹlu ilana iṣakoso ESD boṣewa.

8.3 Niyanju Awọn ipo iṣẹ
lori iwọn iwọn otutu ọfẹ-afẹfẹ ṣiṣẹ (ayafi bibẹẹkọ ṣe akiyesi)

		MIN	MAX	UNIT
Iwọn otutu ibaramu nṣiṣẹ (1) (2)		–40	105	°C
Ipese ipese voltage (VDDS)		1.8	3.8	V
Ipese ipese voltage (VDDS), igbelaruge mode	VDDR = 1.95 V +14 dBm RF ti o njade agbara sub-1 GHz ampitanna	2.1	3.8	V
Nyara ipese voltage pa oṣuwọn		0	100	mV/µs
Ja bo ipese voltage pa oṣuwọn		0	20	mV/µs

(1) Iṣiṣẹ ni tabi sunmọ iwọn otutu iṣiṣẹ ti o pọju fun awọn akoko gigun yoo ja si idinku ninu igbesi aye.
(2) Fun awọn abuda resistance igbona tọka si.
8.4 Power Ipese ati modulu
lori iwọn iwọn otutu ọfẹ-afẹfẹ ṣiṣẹ (ayafi bibẹẹkọ ṣe akiyesi)

PARAMETER		MIN	TYP	MAX	UNIT
VDDS Agbara-lori-Tunto (POR) ala		1.1 – 1.55			V
VDDS Brown-jade Oluwari (BOD) (1)	Ipele ti nyara	1.77			V
VDDS Brown-out Detector (BOD), ṣaaju bata ibẹrẹ (2)	Ipele ti nyara	1.70			V
VDDS Brown-jade Oluwari (BOD) (1)	Ibalẹ ti o ṣubu	1.75			V

(1) Fun ipo igbelaruge (VDDR = 1.95 V), ipilẹṣẹ sọfitiwia awakọ TI yoo ge awọn opin VDDS BOD si o pọju (isunmọ 2.0 V)
(2) Oluwari-jade Brown jẹ gige ni bata ibẹrẹ, iye ti wa ni ipamọ titi ti ẹrọ yoo fi tunto nipasẹ atunto POR tabi PIN RESET_N
8.5 Agbara agbara - Awọn ọna agbara
Nigbati a ba ṣe iwọn lori apẹrẹ itọkasi CC1312PSIP-EM pẹlu Tc = 25 °C, VDDS = 3.6 V pẹlu DC/DC ṣiṣẹ ayafi ti o ba ṣe akiyesi bibẹẹkọ.

PARAMETER		IPO IDANWO	TYP	UNIT
Core Lọwọlọwọ Lilo
Icore	Tunto	Tunto. RESET_N PIN ti a fi idi rẹ mulẹ tabi VDDS ni isalẹ agbara-lori ipilẹ ala (4)	36	.A
	Paade	Paade. Ko si awọn aago nṣiṣẹ, ko si idaduro	150	nA
	Imurasilẹ pẹlu kaṣe idaduro	RTC nṣiṣẹ, Sipiyu, 80KB Ramu ati (apakan) idaduro iforukọsilẹ. RCOSC_LF	0.9	.A
	Imurasilẹ pẹlu kaṣe idaduro	RTC nṣiṣẹ, Sipiyu, 80KB Ramu ati (apakan) iforukọsilẹ idaduro XOSC_LF	1.0	.A
	Imurasilẹ pẹlu kaṣe idaduro	RTC nṣiṣẹ, Sipiyu, 80KB Ramu ati (apakan) iforukọsilẹ idaduro XOSC_LF	2.8	.A
	Imurasilẹ pẹlu kaṣe idaduro	RTC nṣiṣẹ, Sipiyu, 80KB Ramu ati (apakan) iforukọsilẹ idaduro XOSC_LF	2.9	.A
	Laiṣiṣẹ	Awọn ọna Ipese ati Ramu agbara RCOSC_HF	590	.A
Icore	Ti nṣiṣe lọwọ	MCU nṣiṣẹ CoreMark ni 48 MHz RCOSC_HF	2.89	mA
Agbeegbe Lọwọlọwọ Lilo
Iperi	Agbeegbe agbara ašẹ	Delta lọwọlọwọ pẹlu ašẹ ṣiṣẹ	82	.A
	Serial agbara domain	Delta lọwọlọwọ pẹlu ašẹ ṣiṣẹ	5.5
	RF mojuto	Delta lọwọlọwọ pẹlu agbara ašẹ ṣiṣẹ, sise aago, RF mojuto laišišẹ	179
	µDMA	Delta lọwọlọwọ pẹlu aago ṣiṣẹ, module ni laišišẹ	54
	Aago	Delta lọwọlọwọ pẹlu aago ṣiṣẹ, module ko ṣiṣẹ (3)	68
	I2C	Delta lọwọlọwọ pẹlu aago ṣiṣẹ, module ni laišišẹ	8.2
	I2S	Delta lọwọlọwọ pẹlu aago ṣiṣẹ, module ni laišišẹ	22
	SSI	Delta lọwọlọwọ pẹlu aago ṣiṣẹ, module ko ṣiṣẹ (2)	70
	UART	Delta lọwọlọwọ pẹlu aago ṣiṣẹ, module ko ṣiṣẹ (1)	141
	CRYPTO (AES)	Delta lọwọlọwọ pẹlu aago ṣiṣẹ, module ni laišišẹ	21
	PKA	Delta lọwọlọwọ pẹlu aago ṣiṣẹ, module ni laišišẹ	71
	TRNG	Delta lọwọlọwọ pẹlu aago ṣiṣẹ, module ni laišišẹ	30
Sensọ Adarí Engine agbara
ISCE	Ipo ti nṣiṣe lọwọ	24 MHz, ailopin lupu	808	.A
ISCE	Ipo agbara kekere	2 MHz, ailopin lupu	30.1	.A

Nikan kan UART nṣiṣẹ
Nikan SSI kan nṣiṣẹ

GPTimer kan ṣoṣo ti nṣiṣẹ
CC1312PSIP ṣepọ 100 kΩ resistor fa-soke lori nRESET

8.6 Agbara agbara – Awọn ipo Redio
Nigbati a ba ṣe iwọn lori apẹrẹ itọkasi CC1312PSIP-EM pẹlu Tc = 25 °C, VDDS = 3.6 V pẹlu DC/DC ṣiṣẹ ayafi ti o ba ṣe akiyesi bibẹẹkọ.
Lilo ipo igbelaruge (npo VDDR to 1.95 V), yoo mu eto lọwọlọwọ pọ si nipasẹ 15% (ko kan si eto TX + 14 dBm nibiti lọwọlọwọ yii ti wa tẹlẹ).
Icore ti o yẹ ati awọn ṣiṣan Iperi wa ninu awọn nọmba ni isalẹ.

PARAMETER		IPO IDANWO	TYP	UNIT
	Redio gba lọwọlọwọ, 868 MHz		5.8	mA
	Redio atagba lọwọlọwọ deede PA	0 dBm o wu eto 868 MHz	9.4	mA
	Redio atagba lọwọlọwọ deede PA	+10 dBm o wu eto 868 MHz	17.3	mA
	Redio atagba lọwọlọwọ Ipo Igbelaruge, deede PA	+14 dBm o wu eto 868 MHz	28.7	mA

8.7 Nonvolatile (Flash) Memory abuda
Lori iwọn otutu ti afẹfẹ ọfẹ ti n ṣiṣẹ ati VDDS = 3.0 V (ayafi bibẹẹkọ ṣe akiyesi)

PARAMETER	IPO IDANWO	MIN	TYP	MAX	UNIT
Flash eka iwọn		8			KB
Awọn iyipo piparẹ filasi ti o ṣe atilẹyin ṣaaju ikuna, banki ẹyọkan (1) (5)		30			k Awọn iyipo
Awọn iyipo piparẹ filasi atilẹyin ṣaaju ikuna, eka ẹyọkan (2)		60			k Awọn iyipo
Nọmba ti o pọju ti awọn iṣẹ kikọ fun laini ṣaaju ki o to paarẹ eka (3)		83			Kọ Awọn isẹ
Filasi idaduro	105 °C	11.4			Awọn ọdun ni 105 ° C
Flash aladani nu lọwọlọwọ	Apapọ delta lọwọlọwọ	10.7			mA
Akoko piparẹ eka eka filasi(4)	Awọn iyipo odo	10			ms
Akoko piparẹ eka eka filasi(4)	Awọn iyipo 30k	4000			ms
Filaṣi kọ lọwọlọwọ	Apapọ delta lọwọlọwọ, 4 baiti ni akoko kan	6.2			mA
Akoko kikọ Filaṣi (4)	4 baiti ni akoko kan	21.6			.s

Paarẹ ile-ifowopamọ ni kikun ni a ka bi ọna piparẹ ẹyọkan lori eka kọọkan.
Titi di awọn apa iyasọtọ ti alabara 4 le paarẹ lọkọọkan ni afikun awọn akoko 30k ju opin opin banki ipilẹ ti awọn iyipo 30k

Laini ọrọ kọọkan jẹ 2048 die-die (tabi 256 baiti) fife. Idiwọn yii ni ibamu si awọn kikọ iranti lẹsẹsẹ ti 4 (3.1) awọn baiti o kere ju fun kikọ lori gbogbo laini ọrọ kan. Ti afikun ba kọwe si laini ọrọ kanna ni o nilo, paarẹ eka kan nilo ni kete ti nọmba ti o pọ julọ ti awọn iṣẹ kikọ fun ọna kan ti de.
Nọmba yii dale lori Flash ti ogbo ati pe o pọ si lori akoko ati nu awọn iyipo
Gbigbọn filasi lakoko piparẹ tabi awọn ipo eto kii ṣe iṣẹ ṣiṣe ailewu.

8.8 Gbona Resistance Abuda

IGBONA METRIC		Package	UNIT
		MOT (SIP)
		73 PINS
RÉJA	Ipade-si-ibaramu resistance igbona	48.7	°C/W(1)
RθJC(oke)	Junction-to-case (oke) gbona resistance	12.4	°C/W(1)
RθJB	Ipade-si-ọkọ gbona resistance	32.2	°C/W(1)
ψJT	Paramita ijumọsọrọ-si-oke	0.40	°C/W(1)
ψJB	Paramita ijumọsọrọ-si-ọkọ	32.0	°C/W(1)

(1) °C/W = iwọn Celsius fun watt.
8.9 RF Igbohunsafẹfẹ iye
Lori iwọn otutu ti afẹfẹ ọfẹ ti n ṣiṣẹ (ayafi bibẹẹkọ ṣe akiyesi).

PARAMETER	MIN	TYP	MAX	UNIT
Ẹgbẹ igbohunsafẹfẹ	863		930	MHz

8.10 861 MHz si 1054 MHz – Gba (RX)
Nigbati o ba ṣe iwọn lori apẹrẹ itọkasi CC1312PSIP-EM pẹlu Tc = 25 °C, VDDS = 3.0 V pẹlu DC/DC ṣiṣẹ ati agbara giga PA ti a ti sopọ si VDDS ayafi ti bibẹẹkọ ṣe akiyesi.
Gbogbo awọn wiwọn ni a ṣe ni titẹ sii eriali pẹlu ọna RX kan ati ọna TX, ayafi fun agbara giga PA eyiti o jẹwọn ni asopọ eriali ti a ṣe iyasọtọ. Gbogbo awọn wiwọn ni a ṣe.

PARAMETER	IPO IDANWO	MIN	TYP	MAX	UNIT
Gbogbogbo Parameters
Digital ikanni àlẹmọ siseto gba bandiwidi		4		4000	kHz
Iwọn igbesẹ oṣuwọn data		1.5		bps
Awọn itujade spurious 25 MHz si 1 GHz	868 MHz Ṣiṣe awọn itujade ti a ṣe ni ibamu si ETSI EN 300 220	<-57		dBm
Awọn itujade spurious 1 GHz si 13 GHz		<-47		dBm
802.15.4, 50 kbps, ± 25 kHz iyapa, 2-GFSK, 100 kHz RX bandiwidi
Ifamọ	BER = 10–2, 868 MHz	–108		dBm
Ekunrere iye to	BER = 10–2, 868 MHz	10		dBm
Yiyan, ± 200 kHz	BER = 10–2, 868 MHz (1)	44		dB
Yiyan, ± 400 kHz	BER = 10–2, 868 MHz(1)	48		dB
Ìdènà, ± 1 MHz	BER = 10–2, 868 MHz(1)	57		dB
Ìdènà, ± 2 MHz	BER = 10–2, 868 MHz(1)	62		dB
Ìdènà, ± 5 MHz	BER = 10–2, 868 MHz(1)	68		dB
Ìdènà, ± 10 MHz	BER = 10–2, 868 MHz(1)	76		dB
Ijusilẹ aworan (ṣe isanpada aworan ṣiṣẹ)	BER = 10–2, 868 MHz(1)	39		dB
RSSI ìmúdàgba ibiti	Bibẹrẹ lati opin ifamọ	95		dB
RSSI išedede	Bibẹrẹ lati opin ifamọ kọja iwọn agbara ti a fun	±3		dB
802.15.4, 100 kbps, ± 25 kHz iyapa, 2-GFSK, 137 kHz RX bandiwidi
Ifamọ 100 kbps	868 MHz, 1% PER, 127 baiti owo sisan	-101		dBm
Yiyan, ± 200 kHz	868 MHz, 1% PER, 127 baiti owo sisan. Ti o fẹ ifihan agbara ni -96 dBm	38		dB
Yiyan, ± 400 kHz	868 MHz, 1% PER, 127 baiti owo sisan. Ti o fẹ ifihan agbara ni -96 dBm	45		dB
Àjọ-ikanni ijusile	868 MHz, 1% PER, 127 baiti owo sisan. Ti o fẹ ifihan agbara ni -79 dBm	-9		dB
802.15.4, 200 kbps, ± 50 kHz iyapa, 2-GFSK, 311 kHz RX bandiwidi
Ifamọ	BER = 10–2, 868 MHz	–103		dBm
Ifamọ	BER = 10–2, 915 MHz	–103		dBm
Yiyan, ± 400 kHz	BER = 10–2, 915 MHz. Ifihan agbara ti o fẹ 3 dB loke iye ifamọ.	41		dB
Yiyan, ± 800 kHz	BER = 10–2, 915 MHz. Ifihan agbara ti o fẹ 3 dB loke iye ifamọ.	47		dB
Ìdènà, ± 2 MHz	BER = 10–2, 915 MHz. Ifihan agbara ti o fẹ 3 dB loke iye ifamọ.	55		dB
Ìdènà, ± 10 MHz	BER = 10–2, 915 MHz. Ifihan agbara ti o fẹ 3 dB loke iye ifamọ.	67		dB
802.15.4, 500 kbps, ± 190 kHz iyapa, 2-GFSK, 655 kHz RX bandiwidi
Ifamọ 500 kbps	916 MHz, 1% PER, 127 baiti owo sisan	-90		dBm
Yiyan, ± 1 MHz	916 MHz, 1% PER, 127 baiti owo sisan. Ti o fẹ ifihan agbara ni -88 dBm	11		dB
Yiyan, ± 2 MHz	916 MHz, 1% PER, 127 baiti owo sisan. Ti o fẹ ifihan agbara ni -88 dBm	43		dB
Àjọ-ikanni ijusile	916 MHz, 1% PER, 127 baiti owo sisan. Ti o fẹ ifihan agbara ni -71 dBm	-9		dB
SimpleLink™ Gigun Range 2.5 kbps tabi 5 kbps (20 ksym/s, 2-GFSK, ± 5 kHz Iyapa, FEC (Oṣuwọn Idaji), DSSS = 1:2 tabi 1:4, 34 kHz RX Bandwidth
Ifamọ	2.5 kbps, BER = 10–2, 868 MHz	-119		dBm
Ifamọ	5 kbps, BER = 10–2, 868 MHz	-117		dBm
Ekunrere iye to	2.5 kbps, BER = 10–2, 868 MHz	10		dBm
Yiyan, ± 100 kHz	2.5 kbps, BER = 10–2, 868 MHz (1)	49		dB
Yiyan, ± 200 kHz	2.5 kbps, BER = 10–2, 868 MHz (1)	50		dB
Yiyan, ± 300 kHz	2.5 kbps, BER = 10–2, 868 MHz (1)	51		dB
Ìdènà, ± 1 MHz	2.5 kbps, BER = 10–2, 868 MHz (1)	63		dB
Ìdènà, ± 2 MHz	2.5 kbps, BER = 10–2, 868 MHz (1)	68		dB
Ìdènà, ± 5 MHz	2.5 kbps, BER = 10–2, 868 MHz (1)	78		dB
Ìdènà, ± 10 MHz	2.5 kbps, BER = 10–2, 868 MHz (1)	87		dB

Nigbati o ba ṣe iwọn lori apẹrẹ itọkasi CC1312PSIP-EM pẹlu Tc = 25 °C, VDDS = 3.0 V pẹlu DC/DC ṣiṣẹ ati agbara giga PA ti a ti sopọ si VDDS ayafi ti bibẹẹkọ ṣe akiyesi.
Gbogbo awọn wiwọn ni a ṣe ni titẹ sii eriali pẹlu ọna RX kan ati ọna TX, ayafi fun agbara giga PA eyiti o jẹwọn ni asopọ eriali ti a ṣe iyasọtọ. Gbogbo awọn wiwọn ni a ṣe.

PARAMETER	IPO IDANWO	MIN TYP Max	UNIT
Ijusilẹ aworan (ṣe isanpada aworan ṣiṣẹ)	2.5 kbps, BER = 10–2, 868 MHz (1)	45	dB
RSSI ìmúdàgba ibiti	Bibẹrẹ lati opin ifamọ	97	dB
RSSI išedede	Bibẹrẹ lati opin ifamọ kọja iwọn agbara ti a fun	±3	dB
Alailowaya M-Bus
Ifamọ olugba, wM-BUS C-mode, 100 kbps ± 45 kHz	Bandiwidi olugba 236 kHz, BER 1%	-104	dBm
Ifamọ olugba, wM-BUS T-mode, 100 kbps ± 50 kHz	Bandiwidi olugba 236 kHz, BER 1%	-103	dBm
Ifamọ olugba, ipo wM-BUS S2, 32.768 kbps ± 50 kHz	Bandiwidi olugba 196 kHz, BER 1%	-109	dBm
Ifamọ olugba, ipo wM-BUS S1, 32.768 kbps ± 50 kHz	Bandiwidi olugba 311 kHz, BER 1%	-107	dBm
O dara, 4.8 kbps, 39 kHz RX bandiwidi
Ifamọ	BER = 10–2, 868 MHz	-112	dBm
Ifamọ	BER = 10–2, 915 MHz	-112	dBm
Narrowband, 9.6 kbps ± 2.4 kHz iyapa, 2-GFSK, 868 MHz, 17.1 kHz RX bandiwidi
Ifamọ	1% BER	-118	dBm
Ijusile ikanni nitosi	1% BER. Ifihan agbara ti o fẹ 3 dB loke opin ifamọ itọkasi ETSI (-104.6 dBm). Interferer ± 20 kHz	39	dB
Alternate ikanni ijusile	1% BER. Ifihan agbara ti o fẹ 3 dB loke opin ifamọ itọkasi ETSI (-104.6 dBm). Interferer ± 40 kHz	40	dB
Ìdènà, ± 1 MHz	1% BER. Ifihan agbara ti o fẹ 3 dB loke opin ifamọ itọkasi ETSI (-104.6 dBm).	65	dB
Ìdènà, ± 2 MHz		69	dB
Ìdènà, ± 10 MHz		85	dB
1 Mbps, ± 350 kHz iyapa, 2-GFSK, 2.2 MHz RX bandiwidi
Ifamọ	BER = 10–2, 868 MHz	-94	dBm
Ifamọ	BER = 10–2, 915 MHz	-93	dBm
Ìdènà, +2 MHz	BER = 10–2, 915 MHz. Ifihan agbara ti o fẹ 3 dB loke iye ifamọ.	44	dB
Ìdènà, -2 MHz	BER = 10–2, 915 MHz. Ifihan agbara ti o fẹ 3 dB loke iye ifamọ.	27	dB
Ìdènà, +10 MHz	BER = 10–2, 915 MHz. Ifihan agbara ti o fẹ 3 dB loke iye ifamọ.	59	dB
Ìdènà, -10 MHz	BER = 10–2, 915 MHz. Ifihan agbara ti o fẹ 3 dB loke iye ifamọ.	54	dB
Wi-SUN, 2-GFSK
Ifamọ	50 kbps, ± 12.5 kHz iyapa, 2-GFSK, 866.6 MHz, 68 kHz RX BW, 10% PER, 250 baiti owo sisan	-104	dBm
Yiyan, -100 kHz, 50 kbps, ± 12.5 kHz iyapa, 2-GFSK, 866.6 MHz	50 kbps, ± 12.5 kHz iyapa, 2-GFSK, 68 kHz RX bandiwidi, 866.6 MHz, 10% PER, 250 baiti owo sisan. Ifihan agbara ti o fẹ 3 dB loke ipele ifamọ	32	dB
Yiyan, +100 kHz, 50 kbps, ± 12.5 kHz iyapa, 2-GFSK, 866.6 MHz		33	dB
Yiyan, ± 100 kHz, 50 kbps, ± 12.5 kHz iyapa, 2-GFSK, 866.6 MHz		30	dB
Yiyan, -200 kHz, 50 kbps, ± 12.5 kHz iyapa, 2-GFSK, 866.6 MHz		36	dB
Yiyan, +200 kHz, 50 kbps, ± 12.5 kHz iyapa, 2-GFSK, 866.6 MHz		38	dB
Yiyan, ± 200 kHz, 50 kbps, ± 12.5 kHz iyapa, 2-GFSK, 866.6 MHz		37	dB
Ifamọ	50 kbps, ± 25 kHz iyapa, 2-GFSK, 98 kHz RX Bandwidth,918.2 MHz, 10% fun, 250 baiti owo sisan	-104	dBm

Nigbati o ba ṣe iwọn lori apẹrẹ itọkasi CC1312PSIP-EM pẹlu Tc = 25 °C, VDDS = 3.0 V pẹlu DC/DC ṣiṣẹ ati agbara giga PA ti a ti sopọ si VDDS ayafi ti bibẹẹkọ ṣe akiyesi. Gbogbo awọn wiwọn ni a ṣe ni titẹ sii eriali pẹlu ọna RX kan ati ọna TX, ayafi fun agbara giga PA eyiti o jẹwọn ni asopọ eriali ti a ṣe iyasọtọ. Gbogbo awọn wiwọn ni a ṣe.

PARAMETER	IPO IDANWO	MIN TYP Max	UNIT
Yiyan, -200 kHz, 50 kbps, ± 25 kHz iyapa, 2-GFSK, 918.2 MHz	50 kbps, ± 25 kHz iyapa, 2-GFSK, 98 kHz RX bandiwidi, 918.2 MHz, 10% PER, 250 baiti owo sisan. Ifihan agbara ti o fẹ 3 dB loke ipele ifamọ	34	dB
Yiyan, +200 kHz, 50 kbps, ± 25 kHz iyapa, 2-GFSK, 918.2 MHz		35	dB
Yiyan, ± 200 kHz, 50 kbps, ± 25 kHz iyapa, 2-GFSK, 918.2 MHz		34	dB
Yiyan, -400 kHz, 50 kbps, ± 25 kHz iyapa, 2-GFSK, 918.2 MHz		40	dB
Yiyan, +400 kHz, 50 kbps, ± 25 kHz iyapa, 2-GFSK, 918.2 MHz		40	dB
Yiyan, ± 400 kHz, 50 kbps, ± 25 kHz iyapa, 2-GFSK, 918.2 MHz		40	dB
Ifamọ	100 kbps, ± 25 kHz iyapa, 2-GFSK, 866.6 MHz, 135 kHz RX BW, 10% fun, 250 baiti owo sisan	-102	dBm
Ifamọ	100 kbps, ± 25 kHz iyapa, 2-GFSK, 918.2 MHz, 135 kHz RX BW, 10% fun, 250 baiti owo sisan	-101	dBm
Yiyan, -200 kHz, 100 kbps, ± 25 kHz iyapa, 2-GFSK, 866.6 MHz	100 kbps, ± 25 kHz iyapa, 2-GFSK, 135 kHz RX bandiwidi, 866.6 MHz, 10% PER, 250 baiti owo sisan. Ifihan agbara ti o fẹ 3 dB loke ipele ifamọ	37	dB
Yiyan, +200 kHz, 100 kbps, ± 25 kHz iyapa, 2-GFSK, 866.6 MHz		38	dB
Yiyan, ± 200 kHz, 100 kbps, ± 25 kHz iyapa, 2-GFSK, 866.6 MHz		37	dB
Yiyan, -400 kHz, 100 kbps, ± 25 kHz iyapa, 2-GFSK, 866.6 MHz		45	dB
Yiyan, +400 kHz, 100 kbps, ± 25 kHz iyapa, 2-GFSK, 866.6 MHz		45	dB
Yiyan, ± 400 kHz, 100 kbps, ± 25 kHz iyapa, 2-GFSK, 866.6 MHz		45	dB
Ifamọ	100 kbps, ± 50 kHz iyapa, 2-GFSK, 920.9 MHz, 196 kHz RX BW, 10% fun, 250 baiti owo sisan	-100	dBm
Yiyan, -400 kHz, 100 kbps, ± 50 kHz iyapa, 2-GFSK, 920.9 MHz	100 kbps, ± 50 kHz iyapa, 2-GFSK, 196 kHz RX bandiwidi, 920.9 MHz, 10% PER, 250 baiti owo sisan. Ifihan agbara ti o fẹ 3 dB loke ipele ifamọ	40	dB
Yiyan, +400 kHz, 100 kbps, ± 50 kHz iyapa, 2-GFSK, 920.9 MHz		40	dB
Yiyan, ± 400 kHz, 100 kbps, ± 50 kHz iyapa, 2-GFSK, 920.9 MHz		40	dB
Yiyan, -800 kHz, 100 kbps, ± 50 kHz iyapa, 2-GFSK, 920.9 MHz		46	dB
Yiyan, +800 kHz, 100 kbps, ± 50 kHz iyapa, 2-GFSK, 920.9 MHz		52	dB
Yiyan, ± 800 kHz, 100 kbps, ± 50 kHz iyapa, 2-GFSK, 920.9 MHz		48	dB
Ifamọ	150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 918.4 MHz, 273 kHz RX BW, 10% fun, 250 baiti owo sisan	-96	dBm
Yiyan, -400 kHz, 150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 918.4 MHz	150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 273 kHz RX bandiwidi, 918.4 MHz, 10% PER, 250 baiti owo sisan. Ifihan agbara ti o fẹ 3 dB loke ipele ifamọ	41	dB
Yiyan, +400 kHz, 150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 918.4 MHz		42	dB
Yiyan, -800 kHz, 150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 918.4 MHz		46	dB
Yiyan, +800 kHz, 150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 918.4 MHz		49	dB
Ifamọ		-96	dBm

PARAMETER	IPO IDANWO	MIN TYP Max	UNIT
Yiyan, -400 kHz, 150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 920.9 MHz	150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 273 kHz RX bandiwidi, 920.9 MHz, 10% PER, 250 baiti owo sisan. Ifihan agbara ti o fẹ 3 dB loke ipele ifamọ	40	dB
Yiyan, +400 kHz, 150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 920.9 MHz		42	dB
Yiyan, ± 400 kHz, 150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 920.9 MHz		40	dB
Yiyan, -800 kHz, 150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 920.9 MHz		46	dB
Yiyan, +800 kHz, 150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 920.9 MHz		49	dB
Yiyan, ± 800 kHz, 150 kbps, ± 37.5 kHz iyapa, 2-GFSK, 920.9 MHz		46	dB
Ifamọ	200 kbps, ± 50 kHz iyapa, 2-GFSK, 918.4 MHz, 273 kHz RX BW, 10% fun, 250 baiti owo sisan	-97	dBm
Yiyan, -400 kHz, 200 kbps, ± 50 kHz iyapa, 2-GFSK, 918.4 MHz	200 kbps, ± 50 kHz iyapa, 2-GFSK, 273 kHz RX Bandiwidi, 918.4 MHz, 10% PER, 250 baiti owo sisan. Ifihan agbara ti o fẹ 3 dB loke ipele ifamọ	40	dB
Yiyan, +400 kHz, 200 kbps, ± 50 kHz iyapa, 2-GFSK, 918.4 MHz		43	dB
Yiyan, ± 400 kHz, 200 kbps, ± 50 kHz iyapa, 2-GFSK, 918.4 MHz		41	dB
Yiyan, -800 kHz, 200 kbps, ± 50 kHz iyapa, 2-GFSK, 918.4 MHz		46	dB
Yiyan, +800 kHz, 200 kbps, ± 50 kHz iyapa, 2-GFSK, 918.4 MHz		50	dB
Yiyan, ± 800 kHz, 200 kbps, ± 50 kHz iyapa, 2-GFSK, 918.4 MHz		48	dB
Ifamọ	200 kbps, ± 100 kHz iyapa, 2-GFSK, 920.8 MHz, 273 kHz RX BW, 10% fun, 250 baiti owo sisan	-96	dBm
Yiyan, -600 kHz, 200 kbps, ± 100 kHz iyapa, 2-GFSK, 920.8 MHz	200 kbps, ± 100 kHz iyapa, 2-GFSK, 273 kHz RX Bandiwidi, 920.8 MHz,, 10% fun, 250 baiti owo sisan. Ifihan agbara ti o fẹ 3 dB loke ipele ifamọ	43	dB
Yiyan, +600 kHz, 200 kbps, ± 100 kHz iyapa, 2-GFSK, 920.8 MHz		47	dB
Yiyan, ± 600 kHz, 200 kbps, ± 100 kHz iyapa, 2-GFSK, 920.8 MHz		44	dB
Yiyan, -1200 kHz, 200 kbps, ± 100 kHz iyapa, 2-GFSK, 920.8 MHz		51	dB
Yiyan, +1200 kHz, 200 kbps, ± 100 kHz iyapa, 2-GFSK, 920.8 MHz		54	dB
Yiyan, ± 1200 kHz, 200 kbps, ± 100 kHz iyapa, 2-GFSK, 920.8 MHz		51	dB
Ifamọ	300 kbps, ± 75 kHz iyapa, 2-GFSK, 917.6 MHz, 576 kHz RX BW, 10% fun, 250 baiti owo sisan	-94	dBm
Yiyan, -600 kHz, 300 kbps, ± 75 kHz iyapa, 2-GFSK, 917.6 MHz	300 kbps, ± 75 kHz iyapa, 2-GFSK, 576 kHz RX Bandwidth, 917.6 MHz,, 10% PER, 250 baiti owo sisan. Ifihan agbara ti o fẹ 3 dB loke ipele ifamọ	27	dB
Yiyan, +600 kHz, 300 kbps, ± 75 kHz iyapa, 2-GFSK, 917.6 MHz		45	dB
Yiyan, ± 600 kHz, 300 kbps, ± 75 kHz iyapa, 2-GFSK, 917.6 MHz		35	dB
Yiyan, -1200 kHz, 300 kbps, ± 75 kHz iyapa, 2-GFSK, 917.6 MHz		46	dB
Yiyan, +1200 kHz, 300 kbps, ± 75 kHz iyapa, 2-GFSK, 920.8 MHz		50	dB
Yiyan, ± 1200 kHz, 300 kbps, ± 75 kHz iyapa, 2-GFSK, 917.6 MHz		48	dB
WB-DSSS, 240/120/60/30 kbps (480 ksym/s, 2-GFSK, ± 195 kHz Iyapa, FEC (Iwọn Idaji), DSSS = 1/2/4/8, 622 kHz RX BW)
Ifamọ	240 kbps, DSSS = 1, BER = 10–2, 915 MHz	-101	dBm
Ifamọ	120 kbps, DSSS = 2, BER = 10–2, 915 MHz	-103	dBm

PARAMETER	IPO IDANWO	MIN TYP Max	UNIT
Ifamọ	60 kbps, DSSS = 4, BER = 10–2, 915 MHz	-105	dBm
Ifamọ	30 kbps, DSSS = 8, BER = 10–2, 915 MHz	-106	dBm
Ìdènà ± 1 MHz	240 kbps, DSSS = 1, BER = 10–2, 915 MHz	49	dB
Ìdènà ± 2 MHz	240 kbps, DSSS = 1, BER = 10–2, 915 MHz	53	dB
Ìdènà ± 5 MHz	240 kbps, DSSS = 1, BER = 10–2, 915 MHz	58	dB
Ìdènà ± 10 MHz	240 kbps, DSSS = 1, BER = 10–2, 915 MHz	67	dB

(1) Ifihan agbara ti o fẹ 3 dB loke opin ifamọ itọkasi ni ibamu si ETSI EN 300 220 v. 3.1.1

8.11 861 MHz si 1054 MHz - Gbigbe (TX)
Ti wiwọn lori apẹrẹ itọkasi CC1312PSIP-EM pẹlu Tc = 25 °C, VDDS = 3.0 V pẹlu DC/DC ṣiṣẹ ati agbara giga PA ti a ti sopọ si VDDS nipa lilo 2-GFSK, 50 kbps, ± 25 kHz iyapa ayafi ti bibẹẹkọ ṣe akiyesi. Gbogbo awọn wiwọn ni a ṣe ni titẹ sii eriali pẹlu ọna RX kan ati ọna TX, ayafi fun agbara giga PA eyiti o jẹwọn ni asopọ eriali ti a ṣe iyasọtọ. Gbogbo awọn wiwọn ni a ṣe. (1) c

PARAMETER		IPO IDANWO	MIN	TYP	MAX	UNIT
Gbogbogbo paramita
Agbara ti o pọju, ipo igbelaruge PA deede		VDDR = 1.95 V Ipese ti o kere ju voltage (VDDS) fun ipo igbelaruge jẹ 2.1 V 915 MHz	14			dBm
Agbara ti o pọju, PA deede		868 MHz ati 915 MHz	12.4			dBm
O wu agbara siseto ibiti o deede PA		868 MHz ati 915 MHz	34			dB
Iyatọ agbara ijade lori iwọn otutu deede PA		+10 dBm eto Lori iwọn iṣiṣẹ iwọn otutu ti a ṣeduro	±2			dB
Iyatọ agbara ijade lori ipo Igbelaruge iwọn otutu, PA deede		+14 dBm eto Lori iwọn iṣiṣẹ iwọn otutu ti a ṣeduro	±1.5			dB
Awọn itujade spurious ati harmonics
Awọn itujade asan (laisi awọn irẹpọ) PA deede (2)	30 MHz to 1 GHz	+14 dBm eto ETSI ihamọ awọn ẹgbẹ	<-54			dBm
		+14 dBm eto ETSI ita awọn ẹgbẹ ihamọ	<-36			dBm
	1 GHz si 12.75 GHz (ita awọn ẹgbẹ ihamọ ETSI)	Eto +14 dBm awọn ni bandiwidi 1 MHz (ETSI)		<-30	-35	dBm
Awọn itujade apanirun jade-ti-band PA deede, 915 MHz (2)	30 MHz si 88 MHz (laarin awọn ẹgbẹ ihamọ FCC)	+14 dBm eto	<-56			dBm
	88 MHz si 216 MHz (laarin awọn ẹgbẹ ihamọ FCC)	+14 dBm eto	<-52			dBm
	216 MHz si 960 MHz (laarin awọn ẹgbẹ ihamọ FCC)	+14 dBm eto	<-50			dBm
	960 MHz si 2390 MHz ati loke 2483.5 MHz (laarin ẹgbẹ ihamọ FCC)	+14 dBm eto	<-42			dBm
	1 GHz si 12.75 GHz (ita awọn ẹgbẹ ihamọ FCC)	+14 dBm eto		<-40	-44	dBm
Awọn itujade apanirun jade-ti-band PA deede, 920.6/928 MHz (2)	Ni isalẹ 710 MHz (ARIB T-108)	+14 dBm eto	<-36			dBm
	710 MHz si 900 MHz (ARIB T-108)	+14 dBm eto	<-55			dBm
	900 MHz si 915 MHz (ARIB T-108)	+14 dBm eto	<-55			dBm
	930 MHz si 1000 MHz (ARIB T-108)	+14 dBm eto	<-55			dBm
	1000 MHz si 1215 MHz (ARIB T-108)	+14 dBm eto	<-45			dBm
	Ju 1215 MHz (ARIB T-108)	+14 dBm eto	<-30			dBm
Harmonics deede PA	Irẹpọ keji	+ 14 dBm eto, 868 MHz	<-30			dBm
		+ 14 dBm eto, 915 MHz	<-30
	Kẹta ti irẹpọ	+ 14 dBm eto, 868 MHz	<-30			dBm
		+ 14 dBm eto, 915 MHz	<-42
	Harmonic kẹrin	+ 14 dBm eto, 868 MHz	<-30			dBm
		+ 14 dBm eto, 915 MHz	<-30
	Karun ti irẹpọ	+ 14 dBm eto, 868 MHz	<-30			dBm
		+ 14 dBm eto, 915 MHz	<-42

Ti wiwọn lori apẹrẹ itọkasi CC1312PSIP-EM pẹlu Tc = 25 °C, VDDS = 3.0 V pẹlu DC/DC ṣiṣẹ ati agbara giga PA ti a ti sopọ si VDDS nipa lilo 2-GFSK, 50 kbps, ± 25 kHz iyapa ayafi ti bibẹẹkọ ṣe akiyesi. Gbogbo awọn wiwọn ni a ṣe ni titẹ sii eriali pẹlu ọna RX kan ati ọna TX, ayafi fun agbara giga PA eyiti o jẹwọn ni asopọ eriali ti a ṣe iyasọtọ. Gbogbo awọn wiwọn ni a ṣe.(1)

PARAMETER		IPO IDANWO	MIN TYP Max	UNIT
Agbara ikanni nitosi
Agbara ikanni ti o wa nitosi, deede 14 dBm PA	Ikanni ti o wa nitosi, aiṣedeede 20 kHz. 9.6 kbps, h = 0.5	12.5 dBm eto. 868.3 MHz. 14 kHz ikanni BW	-24	dBm
Agbara ikanni omiiran, deede 14 dBm PA	Yiyan ikanni, 40 kHz aiṣedeede. 9.6 kbps, h = 0.5	12.5 dBm eto. 868.3 MHz. 14 kHz ikanni BW	-31	dBm

(1) Diẹ ninu awọn akojọpọ ti igbohunsafẹfẹ, data oṣuwọn ati awose ọna kika nbeere lilo ti ita fifuye gara fun ibamu ilana. Awọn alaye diẹ sii ni a le rii ni errata ẹrọ.
(2) Dara fun awọn eto ifọkansi ibamu pẹlu EN 300 220, EN 303 131, EN 303 204, FCC CFR47 Apá 15, ARIB STD-T108.
8.12 861 MHz si 1054 MHz – PLL Ipo Ariwo Fifẹ Ipo Alakoso
Nigbati a ba wọn lori apẹrẹ itọkasi pẹlu Tc = 25 °C, VDDS = 3.0 V.

PARAMETER	IPO IDANWO	MIN	TYP	MAX	UNIT
Ariwo alakoso ni awọn ẹgbẹ 868- ati 915-MHz 20 kHz PLL loop bandiwidi	± 10 kHz aiṣedeede	–74			dBc/Hz
	± 100 kHz aiṣedeede	–97			dBc/Hz
	± 200 kHz aiṣedeede	–107			dBc/Hz
	± 400 kHz aiṣedeede	–113			dBc/Hz
	± 1000 kHz aiṣedeede	–120			dBc/Hz
	± 2000 kHz aiṣedeede	–127			dBc/Hz
	± 10000 kHz aiṣedeede	–141			dBc/Hz

8.13 861 MHz si 1054 MHz – PLL Ipo Ariwo Narrowband Alakoso
Nigbati a ba wọn lori apẹrẹ itọkasi pẹlu Tc = 25 °C, VDDS = 3.0 V.

PARAMETER	IPO IDANWO	MIN	TYP	MAX	UNIT
Ariwo alakoso ni awọn ẹgbẹ 868- ati 915-MHz 150 kHz PLL loop band pẹlu	± 10 kHz aiṣedeede	–93			dBc/Hz
	± 100 kHz aiṣedeede	–93			dBc/Hz
	± 200 kHz aiṣedeede	–95			dBc/Hz
	± 400 kHz aiṣedeede	–104			dBc/Hz
	± 1000 kHz aiṣedeede	–121			dBc/Hz
	± 2000 kHz aiṣedeede	–130			dBc/Hz
	± 10000 kHz aiṣedeede	–140			dBc/Hz

8.14 Akoko ati Yipada Abuda
8.14.1 Tunto akoko

PARAMETER	MIN	TYP	MAX	UNIT
RESET_N igba kekere	1			.s

8.14.2 Wakeup Time
Wiwọn lori iwọn otutu ọfẹ-afẹfẹ ṣiṣẹ pẹlu VDDS = 3.0 V (ayafi bibẹẹkọ ṣe akiyesi). Awọn akoko ti a ṣe akojọ si nibi ko pẹlu sọfitiwia lori oke.

PARAMETER	IPO IDANWO	MIN	TYP	MAX	UNIT
MCU, Tunto si Ṣiṣẹ(1)		850 – 4000			.s
MCU, Tiipa si Ṣiṣẹ(1)		850 – 4000			.s
MCU, Imurasilẹ si Ṣiṣẹ		165			.s
MCU, Ti nṣiṣe lọwọ si Imurasilẹ		39			.s

Wiwọn lori iwọn otutu ọfẹ-afẹfẹ ṣiṣẹ pẹlu VDDS = 3.0 V (ayafi bibẹẹkọ ṣe akiyesi). Awọn akoko ti a ṣe akojọ si nibi ko pẹlu sọfitiwia lori oke.

PARAMETER	IPO IDANWO	MIN TYP Max	UNIT
MCU, Laiṣiṣẹ si Ṣiṣẹ		15	.s

(1) Akoko jiji da lori idiyele ti o ku lori kapasito VDDR nigbati o ba bẹrẹ ẹrọ naa, ati nitorinaa bawo ni ẹrọ naa ti wa ni Tunto tabi Tiipa ṣaaju ki o to bẹrẹ lẹẹkansi. Awọn ji soke akoko posi pẹlu kan ti o ga kapasito iye.

8.14.3 aago pato
8.14.3.1 48 MHz Crystal Oscillator (XOSC_HF) ati deede igbohunsafẹfẹ RF
Awọn module ni a 48 MHz gara ti o ti wa ni ti sopọ si oscillator. Lakoko idanwo iṣelọpọ ti module, akopọ kapasito inu inu ikojọpọ gara ti wa ni titunse lati dinku aṣiṣe igbohunsafẹfẹ gara. Idanwo iṣelọpọ naa tun n dinku aṣiṣe igbohunsafẹfẹ RF ni iwọn otutu yara nipa titunṣe ọrọ igbohunsafẹfẹ RF (PLL). Atunse ibẹrẹ ti igbohunsafẹfẹ RF ni a lo ninu sọfitiwia (ti o ba ṣiṣẹ) lati san isanpada igbohunsafẹfẹ RF ti o da lori ifoju iwọn otutu fiseete ti gara. Ti ṣe iwọn lori apẹrẹ itọkasi Texas Instruments pẹlu Tc = 25 °C, VDDS = 3.0 V, ayafi bibẹẹkọ ṣe akiyesi.

PARAMETER	MIN	TYP	MAX	UNIT
Crystal igbohunsafẹfẹ	48			MHz
Akoko ibere Crystal oscillator(2)	200			.s
48 MHz ni ibẹrẹ igbohunsafẹfẹ deede ni 25°	-5	2	5	ppm
48 MHz igbohunsafẹfẹ iduroṣinṣin, otutu fiseete -40 ° to 105 °	-16		18	ppm
Crystal ti ogbo, ọdun 5	-2		2	ppm
Crystal ti ogbo, ọdun 10	-4		2	ppm
Ipeye Igbohunsafẹfẹ RF pẹlu sọfitiwia inu ti inu sanpada iwọn otutu, laisi ti ogbo, -40° si 65°. Da lori ifoju kirisita fiseete kọja iwọn otutu lati sipesifikesonu gara ti olupese.	-10		10	ppm

Ṣiṣayẹwo tabi bibẹẹkọ didaduro gara nigba ti oluyipada DC/DC ti ṣiṣẹ le fa ibajẹ ayeraye si ẹrọ naa.

Akoko ibẹrẹ ni lilo awakọ agbara ti TI ti pese. Akoko ibẹrẹ le pọ si ti awakọ ko ba lo.

8.14.3.2 48 MHz RC Oscillator (RCOSC_HF)
Ti ṣe iwọn lori apẹrẹ itọkasi Texas Instruments pẹlu Tc = 25 °C, VDDS = 3.0 V, ayafi bibẹẹkọ ṣe akiyesi.

	MIN	TYP	MAX	UNIT
Igbohunsafẹfẹ	48			MHz
Uncalibrated igbohunsafẹfẹ išedede	±1			%
Ipeye iye iwọn (1)	±0.25			%
Akoko ibẹrẹ	5			.s

Yiye ni ibatan si orisun isọdiwọn (XOSC_HF)

8.14.3.3 2 MHz RC Oscillator (RCOSC_MF)
Ti ṣe iwọn lori apẹrẹ itọkasi Texas Instruments pẹlu Tc = 25 °C, VDDS = 3.0 V, ayafi bibẹẹkọ ṣe akiyesi.

	MIN	TYP	MAX	UNIT
Igbohunsafẹfẹ calibrated	2			MHz
Akoko ibẹrẹ	5			.s

8.14.3.4 32.768 kHz Crystal Oscillator (XOSC_LF) ati deede RTC
Awọn module ni a 32 kHz gara ti o ti wa ni ti sopọ si oscillator. Lakoko idanwo iṣelọpọ ti module, RTC (Aago Aago Gidi) ti o wa lati oscillator 32 kHz gara ti jẹ calibrated ni iwọn otutu yara. Eyi ni a ṣe lati dinku aṣiṣe RTC ti o ṣẹlẹ nipasẹ aṣiṣe ibẹrẹ ti 32 kHz gara. Atunse ibẹrẹ ti RTC ni a lo ninu sọfitiwia (ti o ba ṣiṣẹ) lati sanpada RTC ti o da lori ifoju iwọn otutu fiseete ti gara. Ti ṣe iwọn lori apẹrẹ itọkasi Texas Instruments pẹlu Tc = 25 °C, VDDS = 3.0 V, ayafi bibẹẹkọ ṣe akiyesi.

	MIN	TYP	MAX	UNIT
Crystal igbohunsafẹfẹ	32.768			kHz
Ipeye igbohunsafẹfẹ ibẹrẹ ni 25°	-20	20		ppm
32kHz gara ti ogbo, ọdun akọkọ	-3	3		ppm
Aago Aago gidi (RTC) deede ni lilo isanpada iwọn otutu fun 32kHz xtal (ti o ba ṣiṣẹ ni sọfitiwia), laisi ti ogbo, -40° si awọn iwọn 105°. Da lori ifoju kirisita fiseete kọja iwọn otutu lati sipesifikesonu gara ti olupese.	-100	50		ppm
Aago Aago gidi (RTC) deede ni lilo isanpada iwọn otutu fun 32kHz xtal (ti o ba ṣiṣẹ ni sọfitiwia), laisi ti ogbo, -40° si awọn iwọn 65°. Da lori ifoju kirisita fiseete kọja iwọn otutu lati sipesifikesonu gara ti olupese.	-50	50		ppm

8.14.3.5 32 kHz RC Oscillator (RCOSC_LF)
Ti ṣe iwọn lori apẹrẹ itọkasi Texas Instruments pẹlu Tc = 25 °C, VDDS = 3.0 V, ayafi bibẹẹkọ ṣe akiyesi.

		MIN	TYP	MAX	UNIT
Igbohunsafẹfẹ		32.8			kHz
Iṣatunṣe RTC iyatọ (1)	Ti ṣe atunṣe lorekore lodi si XOSC_HF(2)	± 600 (3)			ppm
Olusodipupo iwọn otutu		50			ppm/°C

Nigbati o ba nlo RCOSC_LF gẹgẹbi orisun fun aago eto igbohunsafẹfẹ kekere (SCLK_LF), išedede ti SCLK_LF-ti ari Real Time Clock (RTC) le ni ilọsiwaju nipasẹ wiwọn RCOSC_LF ibatan si XOSC_HF ati isanpada fun iyara ami si RTC. Iṣẹ ṣiṣe yii wa nipasẹ awakọ Agbara ti TI ti pese.
Sọfitiwia awakọ TI ṣe iwọn RTC ni gbogbo igba ti XOSC_HF ti ṣiṣẹ.
Diẹ ninu awọn iyatọ ẹrọ le kọja 1000 ppm. Isọdiwọn siwaju kii yoo mu iyatọ dara si.

8.14.4 Amuṣiṣẹpọ Serial Interface (SSI) abuda

8.14.4.1.1 Amuṣiṣẹpọ Serial Interface (SSI) abuda lori iwọn iwọn otutu ọfẹ-afẹfẹ ṣiṣẹ (ayafi bibẹẹkọ ṣe akiyesi)

PARAMETER RARA.	PARAMETER		MIN	TYP	MAX	UNIT
S1	tclk_per	SSIClk ọmọ akoko	12		65024	Awọn aago eto (2)
S2(1)	tclk_high	SSIClk ga akoko	0.5			tclk_per
S3(1)	tclk_low	SSIClk kekere akoko	0.5			tclk_per

Tọkasi awọn aworan atọka akoko SSI, ati .

Nigbati o ba nlo awakọ Agbara ti TI ti pese, aago eto SSI nigbagbogbo jẹ 48 MHz.

8.14.5 UART
8.14.5.1 UART Abuda
lori iwọn iwọn otutu ọfẹ-afẹfẹ ṣiṣẹ (ayafi bibẹẹkọ ṣe akiyesi)

PARAMETER	MIN	TYP	MAX	UNIT
Oṣuwọn UART	3			MBAud

8.15 Agbeegbe abuda
8.15.1 AD
8.15.1.1 Afọwọṣe-to-Digital Converter (ADC) abuda
Tc = 25 °C, VDDS = 3.0 V ati voltage igbelosoke sise, ayafi ti bibẹkọ ti woye. (1)
Awọn nọmba iṣẹ ṣiṣe nilo lilo aiṣedeede ati jèrè awọn atunṣe ni sọfitiwia nipasẹ awọn awakọ ADC ti TI pese.

PARAMETER		IPO IDANWO	MIN	TYP	MAX	UNIT
	Iwọn titẹ siitage ibiti		0		VDDS	V
	Ipinnu		12			Awọn die-die
	Sample Oṣuwọn		200			ksps
	Aiṣedeede	Itọkasi deede 4.3V ti inu (2)	±2			LSB
	Aṣiṣe ere	Itọkasi deede 4.3V ti inu (2)	±7			LSB
DNL(4)	Iyatọ aiṣedeede		>–1			LSB
INL	Integral aiṣedeede		±4			LSB
ENOB	Munadoko nọmba ti die-die	Ti abẹnu 4.3 V deede itọkasi (2), 200 kSampTi o kere, 9.6 kHz input ohun orin	9.8			Awọn die-die
		Ti abẹnu 4.3 V deede itọkasi (2), 200 kSampTi o kere, 9.6 kHz input ohun orin, DC/DC ṣiṣẹ	9.8
		VDDS bi itọkasi, 200 kSamples/s, 9.6 kHz ohun orin kikọ	10.1
		Itọkasi inu, voltagati alaabo wiwọn, 32 iṣẹju-aayaamples apapọ, 200 kSamples / s, 300 Hz input ohun orin	11.1
		Itọkasi inu, voltage igbelosoke alaabo, 14-bit mode, 200 kSamples/s, ohun orin igbewọle 600 Hz (5)	11.3
		Itọkasi inu, voltage alaabo iwọn iwọn, 15-bit mode, 200 kSamples/s, ohun orin igbewọle 150 Hz (5)	11.6
THD	Lapapọ ti irẹpọ iparun	Ti abẹnu 4.3 V deede itọkasi (2), 200 kSamples/s, 9.6 kHz ohun igbewọle	–65			dB
		VDDS bi itọkasi, 200 kSamples/s, 9.6 kHz ohun orin kikọ	–70
		Itọkasi inu, voltage alaabo igbelosoke, 32 samples apapọ, 200 kSamples / s, 300 Hz input ohun orin	–72
SINAD, SNDR	Ifihan agbara-si-ariwo ati ipin ipalọlọ	Ti abẹnu 4.3 V deede itọkasi (2), 200 kSamples/s, 9.6 kHz ohun igbewọle	60			dB
		VDDS bi itọkasi, 200 kSamples/s, 9.6 kHz ohun orin kikọ	63
		Itọkasi inu, voltage alaabo igbelosoke, 32 samples apapọ, 200 kSamples / s, 300 Hz input ohun orin	68
SFDR	Spurious-ọfẹ ìmúdàgba ibiti	Ti abẹnu 4.3 V deede itọkasi (2), 200 kSamples/s, 9.6 kHz ohun igbewọle	70			dB
		VDDS bi itọkasi, 200 kSamples/s, 9.6 kHz ohun orin kikọ	73
		Itọkasi inu, voltage alaabo igbelosoke, 32 samples apapọ, 200 kSamples / s, 300 Hz input ohun orin	75
	Akoko iyipada	Iyipada ni tẹlentẹle, akoko-si-jade, aago 24 MHz	50			Awọn Aago Aago
	Lilo lọwọlọwọ	Itọkasi deede 4.3V ti inu (2)	0.40			mA
	Lilo lọwọlọwọ	VDDS bi itọkasi	0.57			mA
	Reference voltage	Itọkasi inu ti o wa titi deede (igbewọle voltage igbelosoke ṣiṣẹ). Fun išedede to dara julọ, iyipada ADC yẹ ki o bẹrẹ nipasẹ TI-RTOS API lati le ṣafikun ere/awọn ifosiwewe isanpada aiṣedeede ti o fipamọ sinu FCFG1	4.3 (2) (3)			V
	Reference voltage	Itọkasi inu ti o wa titi (igbewọle voltage igbelosoke alaabo). Fun išedede to dara julọ, iyipada ADC yẹ ki o bẹrẹ nipasẹ TI-RTOS API lati le pẹlu ere/aiṣedeede awọn okunfa isanpada ti o fipamọ sinu FCFG1. Iye yii jẹyọ lati iye iwọn (4.3V) bi atẹle: V_Ref = 4.3 V × 1408 / 4095	1.48			V
	Reference voltage	VDDS bi itọkasi, input voltage igbelosoke ṣiṣẹ	VDDS			V
	Reference voltage	VDDS bi itọkasi, input voltage igbelosoke alaabo	VDDS / 2.82(3)			V

Tc = 25 °C, VDDS = 3.0 V ati voltage igbelosoke sise, ayafi ti bibẹkọ ti woye. (1)
Awọn nọmba iṣẹ ṣiṣe nilo lilo aiṣedeede ati jèrè awọn atunṣe ni sọfitiwia nipasẹ awọn awakọ ADC ti TI pese.

PARAMETER		IPO IDANWO	MIN TYP Max	UNIT
	Input impedance	200 kSamples/s, voltage igbelosoke ṣiṣẹ. Iṣagbewọle agbara, Imudaniloju igbewọle da lori sampling igbohunsafẹfẹ ati sampakoko ling	>1	MΩ

Lilo IEEE Std 1241-2010 fun imọ-ọrọ ati awọn ọna idanwo
Ifihan agbara igbewọle ti dinku ni inu ṣaaju iyipada, bi ẹnipe voltagIwọn rẹ jẹ 0 si 4.3 V

Ohun elo voltage gbọdọ wa laarin Idiwọn Iwọn to gaju ni gbogbo igba
Ko si awọn koodu sonu
ADC_output = Σ(4 nsamples) >> n, n = fẹ afikun die-die

8.15.2 DAC
8.15.2.1 Digital-to-Analog Converter (DAC) abuda
Tc = 25 °C, VDDS = 3.0 V, ayafi ti bibẹẹkọ ṣe akiyesi.

PARAMETER		IPO IDANWO	MIN	TYP	MAX	UNIT
Gbogbogbo Parameters
	Ipinnu		8			Awọn die-die
VDDS	Ipese voltage	Eyikeyi fifuye, eyikeyi V_REF, ṣaju-idiyele PA, DAC idiyele-fifa ON	1.8		3.8	V
		Fifuye ita (4), eyikeyi V_REF, ṣaaju-idiyele PA, DAC idiyele-fifa PA	2.0		3.8
		Eyikeyi fifuye, V_REF = DCOUPL, ami-idiyele ON	2.6		3.8
FDAC	Igbohunsafẹfẹ aago	Ifipamọ ON (a ṣeduro fun ẹru ita)	16		250	kHz
		Pipa Pipa (ẹrù inu)	16		1000
	Voltage o wu yanju akoko	V_REF = VDDS, saarin PA, ti abẹnu fifuye	13			1 / F_DAC
		V_REF = VDDS, ifipamọ ON, fifuye agbara ita = 20 pF(3)	13.8
	Ita capacitive fifuye			20	200	pF
	Ita resistive fifuye		10			MΩ
	Kukuru Circuit lọwọlọwọ		400			.A
ZMAX	Idiwọn ti o pọju Vref = VDDS, ifipamọ ON, CLK 250 kHz	VDDS = 3.8 V, DAC idiyele-fifa PA	50.8			kí
		VDDS = 3.0 V, DAC idiyele-fifa ON	51.7
		VDDS = 3.0 V, DAC idiyele-fifa PA	53.2
		VDDS = 2.0 V, DAC idiyele-fifa ON	48.7
		VDDS = 2.0 V, DAC idiyele-fifa PA	70.2
		VDDS = 1.8 V, DAC idiyele-fifa ON	46.3
		VDDS = 1.8 V, DAC idiyele-fifa PA	88.9
Ti abẹnu Fifuye – Tesiwaju Time Comparator / Low Power clocked Comparator
DNL	Iyatọ aiṣedeede	V_REF = VDDS, firù = Aago Tesiwaju tabi Olufiwera Titiipa Agbara Kekere F_DAC = 250 kHz	±1			LSB(1)
	Iyatọ aiṣedeede	V_REF = VDDS, firù = Aago Tesiwaju tabi Olufiwera Titiipa Agbara Kekere F_DAC = 16 kHz	±1.2
	Aṣiṣe aiṣedeede(2) Firù = Aago Tesiwaju	V_REF VDDS = 3.8 V	±0.64			LSB(1)
		V_REF VDDS = 3.0 V	±0.81
		V_REF VDDS = 1.8 V	±1.27
		V_REF = DCOUPL, ami-idiyele ON	±3.43
		V_REF = DCOUPL, ami-idiyele PA	±2.88
		V_REF = ADCREF	±2.37
	Aṣiṣe aiṣedeede(2) Fifuye = Comparator Titiikun Agbara Kekere	V_REF VDDS = 3.8 V	±0.78			LSB(1)
		V_REF VDDS = 3.0 V	±0.77
		V_REF VDDS = 1.8 V	±3.46
		V_REF = DCOUPL, ami-idiyele ON	±3.44
		V_REF = DCOUPL, ami-idiyele PA	±4.70
		V_REF = ADCREF	±4.11
	Max koodu o wu voltage variation(2) Firù = Aago Tesiwaju	V_REF VDDS = 3.8 V	±1.53			LSB(1)
		V_REF VDDS = 3.0 V	±1.71
		V_REF VDDS = 1.8 V	±2.10
		V_REF = DCOUPL, ami-idiyele ON	±6.00
		V_REF = DCOUPL, ami-idiyele PA	±3.85
		V_REF = ADCREF	±5.84

Tc = 25 °C, VDDS = 3.0 V, ayafi ti bibẹẹkọ ṣe akiyesi.

PARAMETER		IPO IDANWO	MIN TYP Max	UNIT
	Max koodu o wu voltage iyatọ (2) Fifuye = Low Power clocked Comparator	V_REF VDDS = 3.8 V	±2.92	LSB(1)
		V_REF = VDDS = 3.0 V	±3.06
		V_REF VDDS = 1.8 V	±3.91
		V_REF = DCOUPL, ami-idiyele ON	±7.84
		V_REF = DCOUPL, ami-idiyele PA	±4.06
		V_REF = ADCREF	±6.94
	O wu voltage range(2) Firù = Aago Tesiwaju	V_REF = VDDS = 3.8 V, koodu 1	0.03	V
		V_REF = VDDS = 3.8 V, koodu 255	3.62
		V_REF = VDDS = 3.0 V, koodu 1	0.02
		V_REF = VDDS = 3.0 V, koodu 255	2.86
		V_REF = VDDS = 1.8 V, koodu 1	0.01
		V_REF = VDDS = 1.8 V, koodu 255	1.71
		V_REF = DCOUPL, ṣaju-idiyele PA, koodu 1	0.01
		V_REF = DCOUPL, ṣaju-idiyele PA, koodu 255	1.21
		V_REF = DCOUPL, ṣaju-idiyele ON, koodu 1	1.27
		V_REF = DCOUPL, ṣaju-idiyele ON, koodu 255	2.46
		V_REF = ADCREF, koodu 1	0.01
		V_REF = ADCREF, koodu 255	1.41
	O wu voltage ibiti o(2) Irù = Apapa Titiipa Agbara Kekere	V_REF = VDDS = 3.8 V, koodu 1	0.03	V
		V_REF = VDDS = 3.8 V, koodu 255	3.61
		V_REF = VDDS = 3.0 V, koodu 1	0.02
		V_REF = VDDS = 3.0 V, koodu 255	2.85
		V_REF = VDDS = 1.8 V, koodu 1	0.01
		V_REF = VDDS = 1.8 V, koodu 255	1.71
		V_REF = DCOUPL, ṣaju-idiyele PA, koodu 1	0.01
		V_REF = DCOUPL, ṣaju-idiyele PA, koodu 255	1.21
		V_REF = DCOUPL, ṣaju-idiyele ON, koodu 1	1.27
		V_REF = DCOUPL, ṣaju-idiyele ON, koodu 255	2.46
		V_REF = ADCREF, koodu 1	0.01
		V_REF = ADCREF, koodu 255	1.41
Ikojọpọ ita
INL	Integral aiṣedeede	V_REF = VDDS, F_DAC = 250 kHz	±1	LSB(1)
		V_REF = DCOUPL, F_DAC = 250 kHz	±2
		V_REF = ADCREF, F_DAC = 250 kHz	±1
DNL	Iyatọ aiṣedeede	V_REF = VDDS, F_DAC = 250 kHz	±1	LSB(1)
	Aṣiṣe aiṣedeede	V_REF VDDS = 3.8 V	±0.40	LSB(1)
		V_REF VDDS = 3.0 V	±0.50
		V_REF VDDS = 1.8 V	±0.75
		V_REF = DCOUPL, ami-idiyele ON	±1.55
		V_REF = DCOUPL, ami-idiyele PA	±1.30
		V_REF = ADCREF	±1.10
	Max koodu o wu voltage iyatọ	V_REF VDDS = 3.8 V	±1.00	LSB(1)
		V_REF VDDS = 3.0 V	±1.00
		V_REF VDDS = 1.8 V	±1.00
		V_REF = DCOUPL, ami-idiyele ON	±3.45
		V_REF = DCOUPL, ami-idiyele PA	±2.10
		V_REF = ADCREF	±1.90

O wu voltage ibiti
Fifuye = Low Power clocked Comparator

V_REF = VDDS = 3.8 V, koodu 1

0.03

1 LSB (VREF 3.8 V/3.0 V/1.8 V/DCOUPL/ADCREF) = 14.10 mV/11.13 mV/6.68 mV/4.67 mV/5.48 mV

Pẹlu aiṣedeede comparator
Fifuye> 20 pF yoo mu akoko ifakalẹ pọ si
Keysight 34401A Multimeter

8.15.3 Iwọn otutu ati Atẹle Batiri
8.15.3.1 Sensọ otutu
Ti ṣe iwọn lori apẹrẹ itọkasi Texas Instruments pẹlu Tc = 25 °C, VDDS = 3.0 V, ayafi bibẹẹkọ ṣe akiyesi.

PARAMETER	IPO IDANWO	MIN	TYP	MAX	UNIT
Ipinnu		2			°C
Yiye	-40 °C si 0 °C	±5.0			°C
Yiye	0 °C si 105 °C	±3.5			°C
Ipese voltage iyeida(1)		3.6			°C/V

Sensọ iwọn otutu jẹ isanpada laifọwọyi fun iyatọ VDDS nigba lilo awakọ iwọn otutu TI ti pese.

8.15.3.2 batiri Monitor
Ti ṣe iwọn lori apẹrẹ itọkasi Awọn irinṣẹ Texas pẹlu T = 25 °C, ayafi bibẹẹkọ ṣe akiyesi.

PARAMETER	IPO IDANWO	MIN	TYP	MAX	UNIT
Ipinnu		25			mV
Ibiti o		1.8		3.8	V
Àìsípàárọ́pọ̀ (ó pọ̀ jù)		23			mV
Yiye	VDDS = 3.0 V	22.5			mV
Aṣiṣe aiṣedeede		-32			mV
Aṣiṣe ere		-1			%

8.15.4 Comparators
8.15.4.1 Low-Power clocked Comparator
T = 25 °C, V = 3.0 V, ayafi ti bibẹkọ ti woye.

PARAMETER	IPO IDANWO	MIN	TYP	MAX	UNIT
Iwọn titẹ siitage ibiti		0		VDDS	V
Igbohunsafẹfẹ aago		SCLK_LF
Ti abẹnu itọkasi voltage(1)	Lilo DAC inu pẹlu VDDS bi itọkasi voltage, DAC koodu = 0 – 255	0.024 – 2.865			V
Aiṣedeede	Ti ṣe iwọn ni V_DDS / 2, pẹlu aṣiṣe lati inu DAC	±5			mV
Akoko ipinnu	Igbesẹ lati -50 mV si 50 mV	1			Aago Aago

(1) Comparator le lo ohun inu 8 die-die DAC bi itọkasi rẹ. Ijade DAC voltage ibiti o da lori itọkasi voltage ti yan. Wo

8.15.4.2 Tesiwaju Time Comparator
Tc = 25 ° C, VDDS = 3.0 V, ayafi ti bibẹẹkọ ṣe akiyesi.

PARAMETER	IPO IDANWO	MIN	TYP	MAX	UNIT
Iwọn titẹ siitage ibiti (1)		0		VDDS	V
Aiṣedeede	Ti ṣe iwọn ni V_DDS / 2	±5			mV
Akoko ipinnu	Igbesẹ lati -10 mV si 10 mV	0.70			.s
Lilo lọwọlọwọ	Itọkasi inu	8.0			.A

Iwọn titẹ siitages le ti wa ni ti ipilẹṣẹ ita ati ti sopọ jakejado I/Os tabi ohun ti abẹnu itọkasi voltage le ṣe ipilẹṣẹ nipa lilo DAC

8.15.5 Lọwọlọwọ Orisun
8.15.5.1 Programmable Lọwọlọwọ Orisun
Tc = 25 °C, VDDS = 3.0 V, ayafi ti bibẹẹkọ ṣe akiyesi.

PARAMETER	IPO IDANWO	MIN	TYP	MAX	UNIT
Orisun lọwọlọwọ ibiti o ti le siseto (ibiti logarithmic)		0.25 – 20			.A
Ipinnu		0.25			.A

8.15.6 GPIO
8.15.6.1 GPIO DC Abuda
Awọn wiwọn CBSed si PG2.1:

PARAMETER	IPO IDANWO	MIN	TYP	MAX	UNIT
T_A = 25 °C, V_DDS = 1.8 V
GPIO VOH ni fifuye 8 mA	IOCURR = 2, awọn GPIO awakọ giga nikan	1.56			V
GPIO VOL ni 8 mA fifuye	IOCURR = 2, awọn GPIO awakọ giga nikan	0.24			V
GPIO VOH ni fifuye 4 mA	IOCURR = 1	1.59			V
GPIO VOL ni 4 mA fifuye	IOCURR = 1	0.21			V
GPIO fifa soke lọwọlọwọ	Ipo igbewọle, fifa soke ṣiṣẹ, Vpad = 0 V	73			.A
GPIO pulldown lọwọlọwọ	Ipo igbewọle, fifasilẹ ṣiṣẹ, Vpad = VDDS	19			.A
GPIO kekere-si-giga igbewọle iyipada, pẹlu hysteresis	IH = 1, iyipada voltage fun kika bi 0 → 1	1.08			V
GPIO ga-si-kekere igbewọle iyipada, pẹlu hysteresis	IH = 1, iyipada voltage fun kika bi 1 → 0	0.73			V
GPIO igbewọle hysteresis	IH = 1, iyato laarin 0 → 1ati 1 → 0 ojuami	0.35			V
T_A = 25 °C, V_DDS = 3.0 V
GPIO VOH ni fifuye 8 mA	IOCURR = 2, awọn GPIO awakọ giga nikan	2.59			V
GPIO VOL ni 8 mA fifuye	IOCURR = 2, awọn GPIO awakọ giga nikan	0.42			V
GPIO VOH ni fifuye 4 mA	IOCURR = 1	2.63			V
GPIO VOL ni 4 mA fifuye	IOCURR = 1	0.40			V
T_A = 25 °C, V_DDS = 3.8 V
GPIO fifa soke lọwọlọwọ	Ipo igbewọle, fifa soke ṣiṣẹ, Vpad = 0 V	282			.A
GPIO pulldown lọwọlọwọ	Ipo igbewọle, fifasilẹ ṣiṣẹ, Vpad = VDDS	110			.A
GPIO kekere-si-giga igbewọle iyipada, pẹlu hysteresis	IH = 1, iyipada voltage fun kika bi 0 → 1	1.97			V
GPIO ga-si-kekere igbewọle iyipada, pẹlu hysteresis	IH = 1, iyipada voltage fun kika bi 1 → 0	1.55			V
GPIO igbewọle hysteresis	IH = 1, iyato laarin 0 → 1ati 1 → 0 ojuami	0.42			V
T_A = 25 ° C
VIH	Asuwon ti GPIO igbewọle voltage reliably tumo bi a Ga	0.8*V_DDS			V
VIL	Ti o ga julọ GPIO igbewọle voltage reliably tumo bi a Kekere	0.2*V_DDS			V

8.16 Aṣoju Awọn abuda
Gbogbo awọn wiwọn ni apakan yii ni a ṣe pẹlu Tc = 25 °C ati VDDS = 3.0 V, ayafi bibẹẹkọ ṣe akiyesi. Wo Awọn ipo iṣiṣẹ ti a ṣeduro fun awọn opin ẹrọ. Awọn iye ti o kọja awọn opin wọnyi wa fun itọkasi nikan.
8.16.1 MCU Lọwọlọwọ

8.16.2 RX Lọwọlọwọ

8.16.3 TX Lọwọlọwọ

Table 8-1. Aṣoju TX Lọwọlọwọ ati Agbara Ijade

CC1312PSIP ni 915 MHz, VDDS = 3.0 V (Tiwọn lori LP-EM-CC1312PSIP)
txPower	Eto Agbara TX (SmartRF Studio)	Agbara Ijade Aṣoju [dBm]	Aṣoju Lilo lọwọlọwọ [mA]
0x013F	14	13.8	34.6
0x823F	12.5	12.2	24.9
0x7828	12	11.8	23.5
0x7A15	11	10.9	21.6
0x4C0D	10	10.1	20.0
0x400A	9	9.5	19.1
0x449A	8	8.1	17.1
0x364D	7	6.8	15.3
0x2892	6	6.3	14.8
0x20DC	5	4.9	13.7
0x28D8	4	4	12.6
0x1C46	3	3.7	11.7
0x18D4	2	2.8	11.5
0x16D1	1	0.8	10.6
0x16D0	0	0.3	10.3
0x0CCB	-3	-3.4	8.6
0x0CC9	-5	-5.4	7.9
0x08C7	-7	-8	7.3
0x0AC5	-10	-11.7	6.6
0x08C3	-15	-17.1	5.9
0x08C2	-20	-20.9	5.6

8.16.4 RX Performance

8.16.5 TX Performance

8.16.6 ADC Performance

Alaye Apejuwe

9.1 Ipariview
Abala 4 fihan awọn modulu mojuto ti ẹrọ CC1312PSIP.
9.2 Sipiyu System
-M4F eto Sipiyu, eyi ti nṣiṣẹ awọn
ohun elo ati awọn ipele ti o ga julọ ti awọn akopọ ilana redio.
CC1312PSIP SimpleLink ™ Alailowaya MCU ni Arm Cortex kan ninu
Sipiyu eto jẹ ipilẹ ti iṣẹ ṣiṣe giga, ipilẹ idiyele kekere ti o pade awọn ibeere eto ti imuse iranti kekere, ati lilo agbara kekere, lakoko jiṣẹ iṣẹ ṣiṣe iṣiro to dayato ati idahun eto iyasọtọ si awọn idilọwọ.
Awọn ẹya ara ẹrọ rẹ pẹlu awọn wọnyi:

ARMv7-M faaji iṣapeye fun awọn ohun elo ifibọ ẹsẹ-kekere
Arm Thumb -2 adalu 16- ati eto itọnisọna 32-bit n pese iṣẹ giga ti a nireti ti mojuto Arm 32-bit ni iwọn iranti iwapọ kan
Ṣiṣe koodu iyara n gba akoko ipo oorun pọ si
Ipinnu, mimu idalọwọduro iṣẹ ṣiṣe giga fun awọn ohun elo to ṣe pataki akoko
Nikan-cycle isodipupo itọnisọna ati hardware pin
Pipin hardware ati ki o yara oni-ifihan agbara-processing Iṣalaye isodipupo
Saturating isiro fun ifihan agbara
IEEE 754-ni ifaramọ Ẹyọ Ojuami Lilefoofo kanṣoṣo (FPU)
Ẹka Idaabobo Iranti (MPU) fun awọn ohun elo to ṣe pataki aabo
yokokoro ni kikun pẹlu data ibaramu fun iran aago
- Iboju Data ati Ẹka Wa kakiri (DWT)
– JTAG Ibudo Wiwọle Ṣatunkọ (DAP)
- Flash Patch ati Ẹka Breakpoint (FPB)
Atilẹyin itọpa dinku nọmba awọn pinni ti o nilo fun ṣiṣatunṣe ati wiwa kakiri
- Ẹrọ Itọpa Macrocell Unit (ITM)
- Ẹka Interface Port Wa kakiri (TPIU) pẹlu iṣelọpọ waya ni tẹlentẹle asynchronous (SWO)
Iṣapeye fun iraye si iranti filasi ọmọ-ọkan
Ti sopọ mọ ni wiwọ si 8-KB 4-ọna kaṣe rirọpo laileto fun agbara agbara ti nṣiṣe lọwọ ati awọn ipinlẹ iduro
Lilo agbara-kekere pẹlu awọn ipo oorun ti a ṣepọ
48 MHz isẹ
1.25 DMIPS fun MHz

9.3 Redio (mojuto RF)

RF Core jẹ rọra gaan ati module redio ẹri ọjọ iwaju eyiti o ni ero isise Arm Cortex-M0 ti o ni atọkun RF afọwọṣe ati Circuit band-band, mu data si ati lati ẹgbẹ Sipiyu eto, ati pe o ṣajọ awọn alaye diẹ ninu apo ti a fun. igbekale. Ipilẹ RF nfunni ni ipele giga, API ti o da lori aṣẹ si Sipiyu akọkọ ti awọn atunto ati data ti kọja. Awọn ero isise Arm Cortex-M0 kii ṣe siseto nipasẹ awọn alabara ati pe o wa ni wiwo nipasẹ awakọ RF ti o pese TI ti o wa pẹlu Apo Idagbasoke Software SimpleLink (SDK).
Ipilẹ RF le ṣe adase mu awọn abala pataki akoko ti awọn ilana redio, nitorinaa gbejade Sipiyu akọkọ, eyiti o dinku agbara ati fi awọn orisun diẹ sii silẹ fun ohun elo olumulo. Orisirisi awọn ifihan agbara tun wa lati ṣakoso awọn iyika itagbangba gẹgẹbi awọn iyipada RF tabi awọn olutaja ibiti o wa ni adase.
Orisirisi awọn ọna kika redio Layer ti ara ni a kọ ni apakan bi sọfitiwia asọye redio nibiti ihuwasi redio jẹ asọye boya nipasẹ awọn akoonu ROM redio tabi nipasẹ awọn ọna kika redio ti kii ṣe ROM ti a firanṣẹ ni irisi awọn abulẹ famuwia pẹlu awọn SimpleLink SDKs. Eyi ngbanilaaye aaye ẹrọ redio lati ṣe imudojuiwọn fun atilẹyin awọn ẹya iwaju ti awọn iṣedede paapaa pẹlu awọn imudojuiwọn lori-air (OTA) lakoko ti o tun nlo ohun alumọni kanna.
Akiyesi
Kii ṣe gbogbo awọn akojọpọ awọn ẹya ara ẹrọ, awọn igbohunsafẹfẹ, awọn oṣuwọn data, ati awọn ọna kika iyipada ti a ṣalaye ninu ipin yii ni atilẹyin. Ni akoko pupọ, TI le mu awọn ọna kika redio ti ara tuntun ṣiṣẹ (PHYs) fun ẹrọ naa ati pese awọn nọmba iṣẹ fun awọn PHY ti a yan ninu iwe data. Awọn ọna kika redio ti a ṣe atilẹyin fun ẹrọ kan pato, pẹlu awọn eto iṣapeye lati lo pẹlu awakọ TI RF, wa ninu irinṣẹ SmartRF Studio pẹlu awọn nọmba iṣẹ ṣiṣe ti awọn ọna kika ti o yan ti a rii ni apakan Awọn alaye.

9.3.1 Ohun-ini Redio ọna kika
Redio CC1312PSIP le ṣe atilẹyin fun ọpọlọpọ awọn ọna kika redio ti ara nipasẹ eto awọn agbeegbe ohun elo ni idapo pẹlu famuwia ti o wa ninu ẹrọ ROM, ti o bo ọpọlọpọ awọn iwulo alabara fun iṣapeye si ọna awọn aye bi iyara tabi ifamọ. Eyi ngbanilaaye irọrun nla ni titọka redio mejeeji lati ṣiṣẹ pẹlu awọn ilana aṣẹ-ọrọ bii isọdi ihuwasi fun awọn iwulo ohun elo kan pato.
Table 9-1 yoo fun a yepere loriview ti awọn ẹya ara ẹrọ ti awọn orisirisi ọna kika redio wa ni ROM. Awọn ọna kika redio miiran le wa ni irisi awọn abulẹ famuwia redio tabi awọn eto nipasẹ Apo Idagbasoke Software (SDK) ati pe o le ṣajọpọ awọn ẹya ni ọna ti o yatọ, bakannaa ṣafikun awọn ẹya miiran.
Table 9-1. Atilẹyin ẹya ara ẹrọ

Ẹya ara ẹrọ	Akọkọ 2-(G) Ipo FSK	Ga Data Awọn ošuwọn	Kekere Data Awọn ošuwọn	SimpleLink™ Gigun Ibiti
Iṣaju eto, ọrọ amuṣiṣẹpọ, ati CRC	Bẹẹni	Bẹẹni	Bẹẹni	Rara
Eto gbigba bandiwidi	Bẹẹni	Bẹẹni	Bẹẹni (si isalẹ lati 4 kHz)	Bẹẹni
Data / Oṣuwọn aami (3)	20 to 1000 kbps	≤ 2 Ms	≤ 100 kps	≤ 20 kps
Awoṣe kika	2-(G) FSK	2-(G) FSK 4-(G) FSK	2- (G) FSK 4- (G) FSK	2-(G) FSK
Ọrọ Amuṣiṣẹpọ Meji	Bẹẹni	Bẹẹni	Rara	Rara
Sense ti ngbe (1) (2)	Bẹẹni	Rara	Rara	Rara
Ṣiṣawari Iṣaaju (2)	Bẹẹni	Bẹẹni	Bẹẹni	Rara
Data Whitening	Bẹẹni	Bẹẹni	Bẹẹni	Bẹẹni
RSSI oni-nọmba	Bẹẹni	Bẹẹni	Bẹẹni	Bẹẹni
CRC sisẹ	Bẹẹni	Bẹẹni	Bẹẹni	Bẹẹni
spekitiriumu itọka taara-taara (DSSS)	Rara	Rara	Rara	1:2 1:4 1:8
Atunse aṣiṣe siwaju (FEC)	Rara	Rara	Rara	Bẹẹni
Atọka Didara Ọna asopọ (LQI)	Bẹẹni	Bẹẹni	Bẹẹni	Bẹẹni

Sense ti ngbe ni a le lo lati ṣe imuse iṣakoso HW-ṣaaju-ọrọ (LBT) ati Ṣiṣayẹwo ikanni Clear (CCA) fun ibamu pẹlu iru awọn ibeere ni awọn iṣedede ilana. Eyi wa nipasẹ CMD_PROP_CS redio API.
Sense ti ngbe ati Wiwa Preamble le ṣee lo lati ṣe awọn ipo sniff nibiti redio ti wa ni gigun kẹkẹ lati fi agbara pamọ.
Awọn oṣuwọn data jẹ itọkasi nikan. Awọn oṣuwọn data ni ita ibiti o le tun ṣe atilẹyin. Fun awọn akojọpọ kan pato ti awọn eto, iwọn kekere le ni atilẹyin.

9.4 Iranti

Iranti ti o to 352-KB ti kii ṣe iyipada (Flash) n pese ibi ipamọ fun koodu ati data. Iranti filasi jẹ siseto ninu eto ati paarẹ. Ẹka iranti filasi ti o kẹhin gbọdọ ni apakan Iṣeto Onibara (CCFG) eyiti o lo nipasẹ bata ROM ati TI awọn awakọ ti a pese lati tunto ẹrọ naa. Iṣeto ni a ṣe nipasẹ orisun ccfg.c file ti o wa ninu gbogbo TI pese examples.
Eto jijo ole-kekere Ramu aimi (SRAM) ti pin si awọn bulọọki 16-KB marun ati pe o le ṣee lo fun ibi ipamọ data mejeeji ati ipaniyan koodu. Idaduro awọn akoonu SRAM ni ipo agbara Imurasilẹ ti ṣiṣẹ nipasẹ aiyipada ati pẹlu awọn nọmba agbara agbara ipo imurasilẹ. Ṣiṣayẹwo Parity fun wiwa ti awọn aṣiṣe bit ni iranti ti a ṣe sinu, eyiti o dinku awọn aṣiṣe rirọ ipele-pipẹ ati nitorinaa mu igbẹkẹle pọ si. SRAM System ti wa ni ipilẹṣẹ nigbagbogbo si awọn odo lori ipaniyan koodu lati bata.
Lati mu iyara ipaniyan koodu pọ si ati agbara kekere nigbati o ba n ṣiṣẹ koodu lati iranti ti kii ṣe iyipada, kaṣe 4-KB ti kii ṣe ọna 8 kan ti ṣiṣẹ nipasẹ aiyipada si kaṣe ati awọn ilana prefetch ti a ka nipasẹ Sipiyu eto.
Kaṣe le ṣee lo bi Ramu gbogbogbo nipa ṣiṣe ẹya ara ẹrọ ni agbegbe Iṣeto Onibara (CCFG).
SRAM jijo kekere 4-KB wa fun lilo pẹlu Ẹrọ Adarí Sensọ eyiti o jẹ igbagbogbo lo fun titoju awọn eto Adarí sensọ, data ati awọn aye atunto. Ramu yii tun wa nipasẹ Sipiyu eto. Ramu Adarí sensọ ko ti sọ di mimọ laarin awọn atunto eto.
ROM pẹlu ekuro TI-RTOS ati awọn awakọ ipele kekere, bakanna bi awọn ẹya pataki ti awọn akopọ redio ti a yan, eyiti o ṣe idasilẹ iranti filasi fun ohun elo naa. Awọn ROM tun ni a ni tẹlentẹle (SPI ati UART) bootloader ti o le ṣee lo fun ni ibẹrẹ siseto ti awọn ẹrọ.

9.5 sensọ Adarí

Adarí Sensọ naa ni irin-ajo ti o le mu ṣiṣẹ ni yiyan ni imurasilẹ mejeeji ati awọn ipo agbara Nṣiṣẹ. Awọn agbeegbe ni agbegbe yii le jẹ iṣakoso nipasẹ Ẹrọ Alakoso Sensọ, eyiti o jẹ Sipiyu iṣapeye agbara ohun-ini. Sipiyu yii le ka ati ṣe atẹle awọn sensọ tabi ṣe awọn iṣẹ-ṣiṣe miiran ni adase; nitorina ni pataki idinku agbara agbara ati piparẹ Sipiyu eto.
Sensọ Adarí Engine ni olumulo siseto pẹlu kan ti o rọrun siseto ede ti o ni sintasi iru si C. Eleyi programmability faye gba fun sensọ didi ati awọn miiran awọn iṣẹ-ṣiṣe lati wa ni pato bi lesese aligoridimu kuku ju aimi iṣeto ni ti eka agbeegbe modulu, Aago, DMA, forukọsilẹ ti siseto ipinle. awọn ẹrọ, tabi ipa ọna iṣẹlẹ.

Ilọsiwaju akọkọtages ni:

Irọrun - data le ka ati ni ilọsiwaju ni awọn ọna ailopin lakoko ti o tun n ṣe idaniloju agbara-kekere
Ipo agbara kekere 2 MHz ngbanilaaye mimu ti o ṣeeṣe ti o kere julọ ti awọn sensọ oni-nọmba
Ìmúdàgba ilotunlo ti hardware oro
40-bit accumulator atilẹyin isodipupo, afikun ati naficula
Observability ati yokokoro awọn aṣayan

Studio Adarí Sensọ ni a lo lati kọ, idanwo, ati koodu yokokoro fun Adarí Sensọ. Ọpa naa ṣe agbejade koodu orisun awakọ C, eyiti ohun elo Sipiyu System nlo lati ṣakoso ati paarọ data pẹlu Oluṣakoso sensọ. Awọn ọran lilo deede le jẹ (ṣugbọn ko ni opin si) atẹle naa:

Ka awọn sensọ afọwọṣe nipa lilo ADC ti a ṣepọ tabi awọn afiwera
Awọn sensọ oni-nọmba wiwo ni lilo awọn GPIO, SPI, UART, tabi I2 C jẹ banged-bit)
Imọye agbara
iran Waveform
Kika pulse agbara kekere pupọ (iwọn iwọn sisan) Ṣiṣayẹwo bọtini

Awọn agbeegbe inu Adari Sensọ pẹlu atẹle naa:

Comparator clocked-kekere ni a le lo lati ji Sipiyu eto lati eyikeyi ipinle ninu eyiti comparator n ṣiṣẹ. Itọkasi inu atunto DAC le ṣee lo ni apapo pẹlu olufiwewe.
Ijade ti comparator tun le ṣee lo lati ma nfa idalọwọduro tabi ADC.
Iṣẹ ṣiṣe oye agbara jẹ imuse nipasẹ lilo orisun lọwọlọwọ igbagbogbo, oluyipada akoko-si-nọmba, ati afiwera kan. Ifiwera akoko lilọsiwaju ni bulọọki yii tun le ṣee lo bi yiyan deede ti o ga julọ si afiwera clocked agbara kekere. Adarí Sensọ n ṣe abojuto titele ipilẹ, hysteresis, sisẹ, ati awọn iṣẹ miiran ti o ni ibatan nigbati a lo awọn modulu wọnyi fun oye agbara.
ADC jẹ 12-bit, 200-ksamples/s ADC pẹlu awọn igbewọle mẹjọ ati voltage itọkasi. ADC le ṣe okunfa nipasẹ ọpọlọpọ awọn orisun oriṣiriṣi pẹlu awọn aago, awọn pinni I/O, sọfitiwia, ati awọn afiwera.
Awọn modulu afọwọṣe le sopọ si awọn GPIO oriṣiriṣi mẹjọ
Titunto si SPI igbẹhin pẹlu iyara aago 6 MHz
Awọn agbeegbe inu Oluṣakoso sensọ tun le ṣakoso lati ọdọ ero isise ohun elo akọkọ.

9.6 cryptography

Ẹrọ CC1312PSIP wa pẹlu eto nla ti awọn ohun elo imuyara ohun elo ti o ni ibatan cryptography, ti o dinku ifẹsẹtẹ koodu ati akoko ipaniyan fun awọn iṣẹ cryptographic. O tun ni anfani ti jijẹ agbara kekere ati ilọsiwaju wiwa ati idahun ti eto nitori awọn iṣẹ ṣiṣe cryptografi n ṣiṣẹ ni okun ohun elo abẹlẹ.
Paapọ pẹlu yiyan nla ti awọn ile-ikawe cryptography orisun-ìmọ ti a pese pẹlu Apo Idagbasoke Software (SDK), eyi ngbanilaaye fun aabo ati ẹri ọjọ iwaju awọn ohun elo IoT lati ni irọrun kọ lori oke pẹpẹ naa. Awọn modulu imuyara ohun elo jẹ:

Module Olumuda Nọmba ID otitọ (TRNG) n pese otitọ, orisun ariwo ti kii ṣe ipinnu fun idi ti ipilẹṣẹ awọn bọtini, awọn adaṣe ipilẹṣẹ (IVs), ati awọn ibeere nọmba ID miiran. TRNG ti wa ni itumọ ti lori 24 oruka oscillators ti o ṣẹda unpredictable o wu kikọ sii kan eka ti kii-combinatorial Circuit.
Algorithm Hash to ni aabo 2 (SHA-2) pẹlu atilẹyin fun SHA224, SHA256, SHA384, ati SHA512
Standard ìsekóòdù To ti ni ilọsiwaju (AES) pẹlu 128 ati 256 bit bọtini gigun
Ohun imuyara Bọtini gbangba – Ohun imuyara ohun elo ti n ṣe atilẹyin awọn iṣẹ ṣiṣe mathematiki nilo fun awọn igun elliptic to 512 die-die ati iran bata bọtini RSA to awọn die-die 1024.

Nipasẹ lilo awọn modulu wọnyi ati awọn awakọ cryptography TI ti pese, awọn agbara wọnyi wa fun ohun elo tabi akopọ:

Key Adehun Ero
– Elliptic ti tẹ Diffie – Hellman pẹlu aimi tabi awọn bọtini ephemeral (ECDH ati ECDHE)
- Ọrọigbaniwọle Ifọwọsi Iyipada Iyipada Elliptic nipasẹ Juggling (ECJ-PAKE)
Ibuwọlu Iran
– Elliptic ti tẹ Diffie-Hellman Digital Ibuwọlu alugoridimu (ECDSA)
Àtìlẹyìn Curve
- Fọọmu Weierstrass Kuru (atilẹyin ohun elo ni kikun), gẹgẹbi:
NIST-P224, NIST-P256, NIST-P384, NIST-P521
Brainpool-256R1, Brainpool-384R1, Brainpool-512R1
iṣẹju 256r1
- Fọọmu Montgomery (atilẹyin ohun elo fun isodipupo), gẹgẹbi:
Epo25519
SHA2 orisun MACs
- HMAC pẹlu SHA224, SHA256, SHA384, tabi SHA512
Dina ipo cipher iṣẹ
– AESCCM
- AESGCM
- AESECB
– AESCBC
– AESCBC-MAC
Otitọ ID nọmba iran

Awọn agbara miiran, gẹgẹbi fifi ẹnọ kọ nkan RSA ati awọn ibuwọlu bakanna bi Edwards iru awọn iha elliptic gẹgẹbi Curve1174 tabi Ed25519, tun le ṣe imuse nipa lilo awọn ohun elo ohun elo ti a pese ṣugbọn kii ṣe apakan TI SimpleLink SDK fun ẹrọ CC1312PSIP.

9.7 Aago
Aṣayan titobi ti awọn aago wa bi apakan ti ẹrọ CC1312PSIP. Awọn akoko wọnyi ni:

Aago gidi-gidi (RTC)
Aago 70-ikanni 3-bit ti nṣiṣẹ lori aago eto igbohunsafẹfẹ kekere 32 kHz (SCLK_LF)
Aago yii wa ni gbogbo awọn ipo agbara ayafi Tiipa. Aago le jẹ calibrated lati sanpada fun fiseete igbohunsafẹfẹ nigba lilo LF RCOSC bi aago eto igbohunsafẹfẹ kekere. Ti aago LF ita kan pẹlu igbohunsafẹfẹ yatọ si 32.768 kHz ti lo, iyara ami RTC le ṣe atunṣe lati sanpada fun eyi.
Nigbati o ba nlo TI-RTOS, a lo RTC gẹgẹbi aago ipilẹ ninu ẹrọ ṣiṣe ati pe o yẹ ki o wọle nikan nipasẹ awọn ekuro APIs gẹgẹbi module Aago. Aago akoko gidi le tun jẹ kika nipasẹ Ẹrọ Alakoso sensọ si awọn akokoamp data sensọ ati pe o tun ni awọn ikanni iyaworan igbẹhin. Nipa aiyipada, RTC da duro nigbati oluyipada kan da ẹrọ naa duro.
Awọn Aago Idi Gbogbogbo (GPTIMER)
Awọn GPTIMER mẹrin rọ le ṣee lo bi boya awọn aago 4 × 32 bit tabi awọn aago 8 × 16 bit, gbogbo wọn nṣiṣẹ to 48 MHz. Ọkọọkan awọn aago 16- tabi 32-bit ṣe atilẹyin ọpọlọpọ awọn ẹya ara ẹrọ bii ọkan-shot tabi kika igbakọọkan, awose iwọn pulse (PWM), kika akoko laarin awọn egbegbe ati kika eti. Awọn igbewọle ati awọn ọnajade ti aago naa ni asopọ si aṣọ iṣẹlẹ iṣẹlẹ ẹrọ, eyiti o fun laaye awọn aago lati ṣe ajọṣepọ pẹlu awọn ifihan agbara bii awọn igbewọle GPIO, awọn akoko miiran, DMA ati ADC. Awọn GPTIMER naa wa ni Awọn ọna agbara Nṣiṣẹ ati Laiṣiṣẹ.
Sensọ Adarí Aago
Adarí Sensọ ni awọn aago mẹta ninu:
Aago AUX 0 ati 1 jẹ awọn aago 16-bit pẹlu prescaler 2 kan. Awọn aago le boya pọ si lori aago kan tabi ni eti kọọkan ti orisun ami ti o yan. Mejeeji ọkan-shot ati awọn ipo aago igbakọọkan wa.
Aago AUX 2 jẹ aago 16-bit ti o le ṣiṣẹ ni 24 MHz, 2 MHz tabi 32 kHz ni ominira ti iṣẹ-ṣiṣe Iṣakoso sensọ. Yaworan 4 wa tabi ṣe afiwe awọn ikanni, eyiti o le ṣiṣẹ ni ọkan-shot tabi awọn ipo igbakọọkan. Aago le ṣee lo lati ṣe ipilẹṣẹ awọn iṣẹlẹ fun Ẹrọ Alakoso Sensọ tabi ADC, bakanna fun iṣelọpọ PWM tabi iran igbi.
Aago Redio
Aago 32-bit multichannel ti nṣiṣẹ ni 4 MHz wa gẹgẹbi apakan ti redio ẹrọ naa. Aago redio ni igbagbogbo lo bi ipilẹ akoko ni ibaraẹnisọrọ nẹtiwọki alailowaya nipa lilo ọrọ akoko 32-bit bi akoko nẹtiwọọki. Aago redio ti muuṣiṣẹpọ pẹlu RTC nipa lilo API redio igbẹhin nigbati redio ẹrọ ba wa ni titan tabi paa. Eyi ṣe idaniloju pe fun akopọ nẹtiwọọki kan, aago redio dabi pe o nṣiṣẹ nigbagbogbo nigbati redio ba ṣiṣẹ. Aago redio ni ọpọlọpọ awọn ọran ti a lo ni aiṣe-taara nipasẹ awọn aaye akoko okunfa ni awọn API redio ati pe o yẹ ki o lo nikan nigbati o ba n ṣiṣẹ kirisita igbohunsafẹfẹ giga 48 MHz deede jẹ orisun SCLK_HF.
Aago ajafitafita
Aago aago naa ni a lo lati tun gba iṣakoso ti eto naa ba ṣiṣẹ ni aṣiṣe nitori awọn aṣiṣe sọfitiwia. Nigbagbogbo a lo lati ṣe ipilẹṣẹ idalọwọduro ati tunto ẹrọ naa fun ọran nibiti ibojuwo igbakọọkan ti awọn paati eto ati awọn iṣẹ ṣiṣe kuna lati jẹrisi iṣẹ ṣiṣe to dara. Aago aago naa nṣiṣẹ lori iwọn aago 1.5 MHz ati pe ko le duro ni kete ti o ti ṣiṣẹ. Aago aago naa da duro lati ṣiṣẹ ni ipo agbara Imurasilẹ ati nigbati yokokoro ba da ẹrọ naa duro.

9.8 Tẹlentẹle Agbeegbe ati ki o Mo / awọn

Awọn SSI jẹ awọn atọkun ni tẹlentẹle amuṣiṣẹpọ ti o ni ibamu pẹlu SPI, MICROWIRE, ati awọn atọkun atọwọdọwọ ti TI. Awọn SSI ṣe atilẹyin mejeeji oluwa SPI ati ẹrú to 4 MHz. Awọn modulu SSI ṣe atilẹyin ipele atunto ati polarity.
Awọn UART ṣe imuse olugba asynchronous agbaye ati awọn iṣẹ atagba. Wọn ṣe atilẹyin iran baudrate to rọ titi di iwọn 3 Mbps ti o pọju.
S ni wiwo ti wa ni lilo lati mu awọn oni iwe ati ki o tun le ṣee lo lati ni wiwo pulse-iwuwo modulation microphones (PDM).
Ni wiwo I 2 I C le mu 100 kHz ati 400 kHz ṣiṣẹ, ati pe o le ṣiṣẹ bi oluwa ati ẹrú.
C ni wiwo tun lo lati ṣe ibasọrọ pẹlu awọn ẹrọ ibaramu pẹlu boṣewa I 2 C. I 2 Olutọju I/O (IOC) n ṣakoso awọn pinni I/O oni-nọmba ati pe o ni circuitry multiplexer lati jẹ ki a ṣeto awọn agbeegbe si awọn pinni I/O ni ọna rọ. Gbogbo awọn I/O oni-nọmba jẹ idalọwọduro ati ji dide ti o lagbara, ni fifa eto ati iṣẹ fifalẹ, ati pe o le ṣe idalọwọduro lori odi tabi eti rere (iṣeto atunto). Nigbati o ba tunto bi iṣẹjade, awọn pinni le ṣiṣẹ bi boya titari-fa tabi ṣiṣi-igbẹ. Awọn GPIO marun ni awọn agbara awakọ-giga, eyiti a samisi ni igboya ni Abala 7. Gbogbo awọn agbeegbe oni-nọmba le ni asopọ si PIN oni-nọmba eyikeyi lori ẹrọ naa.
Fun alaye diẹ ẹ sii, wo CC13x2, CC26x2 SimpleLink™ Alailowaya MCU Itọkasi Imọ-ẹrọ.

9.9 Batiri ati Atẹle iwọn otutu
A ni idapo otutu ati batiri voltage atẹle wa ninu ẹrọ CC1312PSIP. Batiri naa ati atẹle iwọn otutu ngbanilaaye ohun elo lati ṣe atẹle nigbagbogbo ni iwọn otutu chip ati ipese voltage ati dahun si awọn ayipada ninu awọn ipo ayika bi o ṣe nilo. Awọn module ni awọn window comparators lati da gbigbi awọn Sipiyu eto nigba ti iwọn otutu tabi ipese voltage lọ ita telẹ windows. Awọn iṣẹlẹ wọnyi tun le ṣee lo lati ji ẹrọ naa lati ipo imurasilẹ nipasẹ aṣọ iṣẹlẹ Nigbagbogbo-Lori (AON).

9.10 µDMA
Ẹrọ naa pẹlu oluṣakoso wiwọle si iranti taara (µDMA). Adarí µDMA n pese ọna lati gbe awọn iṣẹ gbigbe data kuro lati Sipiyu eto, nitorinaa ngbanilaaye fun lilo daradara siwaju sii ti ero isise ati bandiwidi ọkọ akero to wa. Oluṣakoso µDMA le ṣe gbigbe laarin iranti ati awọn agbeegbe. Adarí µDMA naa ni awọn ikanni iyasọtọ fun ọkọọkan atilẹyin lori-chip module ati pe o le ṣe eto lati ṣe awọn gbigbe laifọwọyi laarin awọn agbeegbe ati iranti nigbati agbeegbe ba ṣetan lati gbe data diẹ sii.
Diẹ ninu awọn ẹya ti oludari µDMA pẹlu atẹle yii (eyi kii ṣe atokọ pipe):

Giga rọ ati iṣẹ ikanni atunto ti to awọn ikanni 32
Awọn ọna gbigbe: iranti-si-iranti, iranti-si-ẹgbeegbe, agbeegbe-si-iranti, ati agbeegbe-si-agbeegbe
Awọn iwọn data ti 8, 16, ati 32 die-die
Ipo Ping-pong fun ṣiṣanwọle data lemọlemọfún

9.11 Ṣatunkọ
Atilẹyin yokokoro lori-chip jẹ ṣiṣe nipasẹ cJ ti a ṣe iyasọtọTAG (IEEE 1149.7) tabi JTAG (IEEE 1149.1) ni wiwo.
Ẹrọ bata nipasẹ aiyipada sinu cJTAG ipo ati pe o gbọdọ tunto lati lo 4-pin JTAG.
9.12 Iṣakoso agbara
Lati dinku agbara agbara, CC1312PSIP ṣe atilẹyin nọmba awọn ipo agbara ati awọn ẹya iṣakoso agbara (wo Tabili 9-2).

Table 9-2. Awọn ọna agbara

MODE	SOFTWARE atunto AGBARA ipa				Tunto PIN WA
MODE	OSISE	IDLE	DURO DIE	PAADE	Tunto PIN WA
Sipiyu	Ti nṣiṣe lọwọ	Paa	Paa	Paa	Paa
Filaṣi	On	Wa	Paa	Paa	Paa
SRAM	On	On	Idaduro	Paa	Paa
Redio	Wa	Wa	Paa	Paa	Paa
Ipese System	On	On	Yiyipo Ojuse	Paa	Paa
Forukọsilẹ ati Sipiyu idaduro	Ni kikun	Ni kikun	Apa kan	Rara	Rara
SRAM idaduro	Ni kikun	Ni kikun	Ni kikun	Rara	Rara
48 MHz aago iyara giga (SCLK_HF)	XOSC_HF tabi RCOSC_HF	XOSC_HF tabi RCOSC_HF	Paa	Paa	Paa
Aago iyara alabọde 2 MHz (SCLK_MF)	RCOSC_MF	RCOSC_MF	Wa	Paa	Paa
32 kHz aago iyara kekere (SCLK_LF)	XOSC_LF tabi RCOSC_LF	XOSC_LF tabi RCOSC_LF	XOSC_LF tabi RCOSC_LF	Paa	Paa
Awọn agbeegbe	Wa	Wa	Paa	Paa	Paa
Sensọ Adarí	Wa	Wa	Wa	Paa	Paa
Ji-soke lori RTC	Wa	Wa	Wa	Paa	Paa
Ji-soke lori pin eti	Wa	Wa	Wa	Wa	Paa
Ji-soke lori pin atunto	On	On	On	On	On
Awari Brownout (BOD)	On	On	Yiyipo Ojuse	Paa	Paa
Atunto-agbara (POR)	On	On	On	Paa	Paa
Aago oluṣọ (WDT)	Wa	Wa	Daduro	Paa	Paa

Ni ipo ti nṣiṣe lọwọ, eto ohun elo Sipiyu n ṣiṣẹ koodu ṣiṣẹ. Ipo ti nṣiṣe lọwọ pese iṣẹ deede ti ero isise ati gbogbo awọn agbeegbe ti o ṣiṣẹ lọwọlọwọ. Aago eto le jẹ orisun aago eyikeyi ti o wa (wo Tabili 9-2).
Ni ipo Aiṣiṣẹ, gbogbo awọn agbeegbe ti nṣiṣe lọwọ le wa ni clocked, ṣugbọn ohun elo Sipiyu inu ohun elo ati iranti ko ni aago ati pe ko si koodu ṣiṣẹ. Eyikeyi iṣẹlẹ idalọwọduro mu ero isise pada sinu ipo ti nṣiṣe lọwọ.
Ni ipo Imurasilẹ, aaye nigbagbogbo-lori (AON) nikan nṣiṣẹ. Iṣẹlẹ jide ita, iṣẹlẹ RTC, tabi iṣẹlẹ Adarí sensọ ni a nilo lati mu ẹrọ naa pada si ipo ti nṣiṣe lọwọ. Awọn agbeegbe MCU pẹlu idaduro ko nilo lati tunto nigbati o ji lẹẹkansi, ati Sipiyu tẹsiwaju ipaniyan lati ibiti o ti lọ si ipo imurasilẹ. Gbogbo awọn GPIO ti wa ni idaduro ni ipo imurasilẹ.
Ni ipo tiipa, ẹrọ naa ti wa ni pipa patapata (pẹlu aaye AON ati Adari Sensọ), ati awọn I/Os ti wa ni dimu pẹlu iye ti wọn ni ṣaaju titẹ si ipo titiipa. Iyipada ti ipinle lori eyikeyi I/O pinni asọye bi ji lati PIN tiipa ti ji ẹrọ naa ati awọn iṣẹ bi okunfa atunto. Sipiyu le ṣe iyatọ laarin atunto ni ọna yii ati atunto-nipasẹ-tunto pin tabi ipilẹ agbara-lori nipasẹ kika iforukọsilẹ ipo atunto. Ipo kanṣoṣo ti o wa ni ipo yii ni ipo I/O ti a latched ati awọn akoonu iranti filasi.

Adarí Sensọ jẹ ero isise adase ti o le ṣakoso awọn agbeegbe inu Adari sensọ ni ominira ti Sipiyu eto. Eyi tumọ si pe Sipiyu eto ko ni lati ji, fun example lati ṣe ohun ADC sampling tabi idibo sensọ oni-nọmba kan lori SPI, nitorinaa fifipamọ mejeeji lọwọlọwọ ati akoko ji ti yoo bibẹẹkọ jẹ sofo. Ohun elo Studio Adarí Sensọ n fun olumulo laaye lati ṣe eto Adarí Sensọ, ṣakoso awọn agbeegbe rẹ, ati ji Sipiyu eto bi o ti nilo. Gbogbo awọn agbeegbe Adarí sensọ le tun jẹ iṣakoso nipasẹ Sipiyu eto.

Akiyesi
Agbara, RF ati iṣakoso aago fun ẹrọ CC1312PSIP nilo iṣeto ni pato ati mimu nipasẹ sọfitiwia fun iṣẹ iṣapeye. Iṣeto ati mimu yii jẹ imuse ni awọn awakọ TI ti pese ti o jẹ apakan ti ohun elo idagbasoke sọfitiwia CC1312PSIP (SDK). Nitorinaa, TI ṣeduro gaan ni lilo ilana sọfitiwia yii fun gbogbo idagbasoke ohun elo lori ẹrọ naa. SDK pipe pẹlu TI-RTOS (aṣayan), awakọ ẹrọ, ati examples funni ni ọfẹ ni koodu orisun.
9.13 aago Systems
Ẹrọ CC1312PSIP ni ọpọlọpọ awọn aago eto inu.
48 MHz SCLK_HF ti lo bi aago akọkọ (MCU ati awọn agbeegbe). Eleyi le wa ni ìṣó nipasẹ awọn ti abẹnu 48 MHz RC Oscillator (RCOSC_HF) tabi ni-package 48 MHz gara (XOSC_HF). Akiyesi pe iṣẹ redio nṣiṣẹ ni pipa ti o wa ninu, ninu-package 48 MHz gara laarin module. Igbohunsafẹfẹ kirisita jẹ iwọn ni iṣelọpọ ni iwọn otutu yara lati dinku aṣiṣe igbohunsafẹfẹ ibẹrẹ si o kere ju. Eyi ni a ṣe nipa siseto akojọpọ kapasito inu si iye ti o funni ni isunmọ si 48 MHz.
SCLK_LF ni 32.768 kHz ti abẹnu kekere-igbohunsafẹfẹ eto aago. O le ṣee lo nipasẹ Oluṣakoso sensọ fun iṣẹ agbara-kekere ati pe o tun lo fun RTC ati lati mu aago redio ṣiṣẹpọ ṣaaju tabi lẹhin ipo agbara Imurasilẹ. SCLK_LF le ti wa ni ìṣó nipasẹ awọn ti abẹnu 32.8 kHz RC Oscillator (RCOSC_LF) tabi awọn to wa, ni-package 32.768 kHz gara laarin awọn module.
Nigbati o ba nlo kirisita tabi oscillator RC ti inu, ẹrọ naa le ṣe ifihan ifihan 32 kHz SCLK_LF si awọn ẹrọ miiran, nitorinaa dinku idiyele eto gbogbogbo.

9.14 Network isise
Ti o da lori iṣeto ọja, ẹrọ CC1312PSIP le ṣiṣẹ bi ero isise nẹtiwọọki alailowaya (WNP – ẹrọ ti n ṣiṣẹ akopọ ilana alailowaya pẹlu ohun elo ti n ṣiṣẹ lori MCU agbalejo lọtọ), tabi bi eto-lori-chip (SoC) pẹlu ohun elo ati akopọ ilana nṣiṣẹ lori Sipiyu eto inu ẹrọ naa.
Ni akọkọ nla, awọn ita ogun MCU ibasọrọ pẹlu awọn ẹrọ nipa lilo SPI tabi UART. Ni ọran keji, ohun elo naa gbọdọ kọ ni ibamu si ilana ohun elo ti a pese pẹlu akopọ Ilana alailowaya.

9.15 Ẹrọ Ijẹrisi ati Ijẹrisi
Module lati TI jẹ ifọwọsi fun FCC ati IC/ISED. Awọn alabara TI ti o kọ awọn ọja ti o da lori module TI le fipamọ ni idiyele idanwo ati akoko fun idile ọja.

Akiyesi
Awọn FCC ati awọn ID IC gbọdọ wa ni inu iwe afọwọkọ olumulo mejeeji ati lori apoti. Nitori iwọn kekere ti module (7 mm x 7 mm), gbigbe awọn ID ati awọn isamisi sinu iwọn iru ti o tobi to lati jẹ legible laisi iranlọwọ ti titobi jẹ aiṣedeede.

Table 9-3. Akojọ ti awọn iwe-ẹri

Ara ilana	Sipesifikesonu	ID (Ti o ba wulo)
FCC (AMẸRIKA)	15.247 Isẹ laarin 902-928 MHz iye	ZAT-1312PSIP-1
IC/ISED (Kanada)	RSS-247 Isẹ laarin 902–928 MHz iye	451H-1312PSIP1
ETSI/CE (Europe) & RER (UK)	EN 300 220, 863 -870 MHz iye	–
	EN 303 204, 870-876 MHz iye
	EN 303 659, 865-868 MHz ati 915-919.4MHz

9.15.1 FCC Ijẹrisi ati Gbólóhùn

Ṣọra
Gbólóhùn Ifihan Radiation FCC RF:
Ohun elo yii ni ibamu pẹlu awọn opin ifihan itankalẹ FCC ti a ṣeto fun agbegbe ti a ko ṣakoso. Awọn olumulo ipari gbọdọ tẹle awọn ilana iṣiṣẹ kan pato fun itelorun awọn opin ifihan RF. Atagba yii ko gbọdọ wa ni ipo papọ tabi ṣiṣẹ pẹlu eriali miiran tabi atagba.

Module CC1312PSIPMOT lati TI jẹ ifọwọsi fun FCC gẹgẹbi atagba-modulu kan. Module naa jẹ ẹya FCC-ifọwọsi redio module ti o gbe ẹbun modulu kan.
A kilọ fun ọ pe awọn iyipada tabi awọn iyipada ti ko fọwọsi ni pato nipasẹ ẹgbẹ ti o ni iduro fun ibamu le sọ aṣẹ olumulo di ofo lati ṣiṣẹ ohun elo naa.
Ẹrọ yii ti gbero lati ni ibamu pẹlu Apá 15 ti Awọn ofin FCC. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:

Ẹrọ yii le ma fa kikọlu ipalara.
Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa iṣẹ ti a ko fẹ fun ẹrọ naa.

9.15.2 IC / ISED Ijẹrisi ati Gbólóhùn

Ṣọra
Gbólóhùn Ifihan Radiation IC RF:
Lati ni ibamu pẹlu awọn ibeere ifihan IC RF, ẹrọ yii ati eriali rẹ ko gbọdọ wa ni ipo papọ tabi ṣiṣẹ ni apapo pẹlu eyikeyi eriali miiran tabi atagba.
Module CC1312PSIPMOT lati TI jẹ ifọwọsi fun IC gẹgẹbi atagba kan-modul. module CC1312PSIPMOT lati TI ni ibamu pẹlu ifọwọsi apọjuwọn IC ati awọn ibeere isamisi. IC tẹle idanwo kanna ati awọn ofin bi FCC nipa awọn modulu ifọwọsi ni ohun elo ti a fun ni aṣẹ.
Ẹrọ yii ni ibamu pẹlu awọn iṣedede RSS laisi iwe-aṣẹ Ile-iṣẹ Canada.
Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:

Ẹrọ yii le ma fa kikọlu.
Ẹrọ yii gbọdọ gba kikọlu eyikeyi, pẹlu kikọlu ti o le fa iṣẹ ti a ko fẹ fun ẹrọ naa.

9.16 Module Markings
olusin 9-1 fihan awọn oke-ẹgbẹ siṣamisi fun CC1312PSIP module.

Table 9-4 awọn akojọ ti CC1312PSIP module markings.
Table 9-4. Module Awọn apejuwe

SAMIJI	Apejuwe
CC1312	Generic Apá Number
P	Awoṣe
SIP	SIP = Iru modulu, X = itusilẹ tẹlẹ
NNN NNNN	LTC (Kọọdu Iwa kakiri)

9.17 Ipari Ifamisi Ọja
Module CC1312PSIPMOT ni ibamu pẹlu ẹbun FCC apọjuwọn ẹyọkan, FCC ID: ZAT-1312PSIP-1.
Eto agbalejo ti nlo module yii gbọdọ ṣe afihan aami ti o han ti o nfihan ọrọ atẹle:
FCC ID ninu: ZAT-1312PSIP-1
Module CC1312PSIPMOT ni ibamu pẹlu ẹbun IC modular IC ẹyọkan, IC: 451H-1312PSIP1. Eto agbalejo ti nlo module yii gbọdọ ṣe afihan aami ti o han ti o nfihan ọrọ atẹle:
Ni ninu IC: 451H-1312PSIP1
Fun alaye diẹ sii lori isamisi ọja ipari ati sample aami, jọwọ wo apakan 4 ti OEM Integrators Itọsọna
9.18 Alaye Afowoyi si Olumulo Ipari
Oluṣeto OEM gbọdọ mọ lati ma pese alaye si olumulo ipari nipa bi o ṣe le fi sii tabi yọkuro module RF yii ni afọwọṣe olumulo ti ọja ipari eyiti o ṣepọ module yii. Iwe afọwọkọ olumulo ipari gbọdọ ni gbogbo alaye ilana ti a beere ati awọn ikilọ gẹgẹbi a ṣe han ninu iwe afọwọkọ yii.

Ohun elo, imuse, ati Ìfilélẹ

Akiyesi
Alaye ni apakan Awọn ohun elo atẹle kii ṣe apakan ti sipesifikesonu paati TI, ati pe TI ko ṣe atilẹyin deede tabi pipe. Awọn alabara TI jẹ iduro fun ṣiṣe ipinnu ibamu ti awọn paati fun awọn idi wọn. Awọn alabara yẹ ki o fọwọsi ati idanwo imuse apẹrẹ wọn lati jẹrisi iṣẹ ṣiṣe eto.

10.1 Alaye ohun elo
10.1.1 Aṣoju Ohun elo Circuit
olusin 10-1 fihan awọn aṣoju sikematiki elo lilo CC1312PSIP module. Fun sikematiki itọkasi ni kikun, ṣe igbasilẹ Apẹrẹ LP-EM-CC1312PSIP Files.
Akiyesi
Awọn itọnisọna wọnyi ni a ṣe iṣeduro fun imuse ti apẹrẹ RF:

Rii daju pe ọna RF ti ṣe apẹrẹ pẹlu ikọlu abuda ti 50 Ω.
Ṣiṣatunṣe ti nẹtiwọọki ibaamu impedance eriali jẹ iṣeduro lẹhin iṣelọpọ PCB si akọọlẹ fun parasitics PCB. Jọwọ tọkasi CC13xx/CC26xx Hardware Iṣeto ni ati PCB Design ero; apakan 5.1 fun alaye siwaju sii.

Table 10-1 pese awọn iwe ohun elo fun aṣoju ohun elo lilo CC1312PSIP module ni Figure 10-1.
A ṣe iṣeduro nigbagbogbo lati fi pi-filter sii (Z9, Z10 ati Z11) laarin paadi RF ati eriali / SMA asopo. Nigbati o ba baamu si eriali, eyi yoo dinku awọn adanu aiṣedeede ti eriali naa. Ibaramu-kekere tabi nẹtiwọọki ibaamu giga-giga le jẹ yiyan ni igbagbogbo.
Fun CC1312PSIP, o gba ọ niyanju lati lo ere-kere eriali kekere nitori eyi yoo ba eriali naa mu mejeeji ṣugbọn yoo tun ṣe bi iṣẹ àlẹmọ kekere-kekere bi daradara. Bi o ti le ri ninu olusin 10-1, Z10 ati Z11 fẹlẹfẹlẹ kan ti kekere-kọja eriali baramu lori LP-EM-CC1312PSIP ti o ni ohun ese PCB eriali.
Ni iṣẹlẹ ti ko si awọn paati ibaramu ti a beere fun eriali tabi asopọ taara si SMA kan, o gba ọ niyanju lati lo Z10: 5.6 nH ati Z11: 1.8 pF bi àlẹmọ-kekere.
Fun apẹrẹ itọkasi iṣẹ ṣiṣe ni kikun, wo Apẹrẹ LP-EM-CC1312PSIP Files.
Table 10-1. Bill of Ohun elo

QTY	Itọkasi APA	IYE	Olupese	PART NOMBA	Apejuwe
1	C57	100pF	Murata	GRM0335C1H101GA01D	Kapasito, Seramiki C0G/NP0, 100pF, 50V, -2%/+2%, -55DEGC/+125DEGC, 0201, SMD
1	U1	CC1312PSIP	Texas Instruments	CC1312PSIP	IC, CC1312PSIP, LGA73, SMD
1	Z10	8.2nH	Murata	LQP03TN8N2J02D	Inductor, RF, Chip, Kokoro oofa, 8.2nH, -5%/+5%, 0.25A, -55DEGC/ +125DEGC, 0201, SMD
1	Z11	1.8pF	Murata	GRM0335C1H1R8BA01J	Kapasito, Seramiki C0G/NP0, 1.8pF, 50V, -0.1pF/+0.1pF, -55DEGC/ +125DEGC, 0201, SMD

10.2 Asopọ ẹrọ ati Awọn ipilẹ Ifilelẹ
10.2.1 Tunto

Lati le pade awọn ibeere agbara-lori atunto module, VDDS (Pin 46) ati VDDS_PU (Pin 47) yẹ ki o sopọ papọ. Ti ifihan agbara atunto ko ba da lori agbara-lori atunto ati pe o jẹ jija lati MCU ita, lẹhinna VDDS_PU (Pin 47) yẹ ki o jẹ Ko si Sopọ (NC).
10.2.2 ajeku Pinni
Gbogbo awọn pinni ti ko lo ni a le fi silẹ laisi asopọ laisi ibakcdun ti nini lọwọlọwọ jijo. Jọwọ tọka si #unique_98 fun alaye diẹ sii.

10.3 Awọn Itọsọna Ifilelẹ PCB
Abala yii ṣe alaye awọn itọnisọna PCB lati yara si apẹrẹ PCB ni lilo module CC1312PSIP. Oluṣeto ti awọn modulu gbọdọ wa ni ibamu pẹlu awọn iṣeduro ifilelẹ PCB ti a ṣalaye ninu awọn abala wọnyi lati dinku eewu pẹlu awọn iwe-ẹri ilana fun FCC, IC/ISED, ETSI/CE. Pẹlupẹlu, TI ṣeduro awọn alabara lati tẹle awọn itọnisọna ti a ṣalaye ni apakan yii lati ṣaṣeyọri iru iṣẹ ṣiṣe ti o gba pẹlu apẹrẹ itọkasi TI.

10.3.1 Gbogbogbo Layout awọn iṣeduro
Rii daju pe awọn iṣeduro ifilelẹ gbogbogbo atẹle wọnyi:

Ni a ri to ilẹ ofurufu ati ilẹ vias labẹ awọn module fun idurosinsin eto ati ki o gbona dissipation.
Ma ṣe ṣiṣe awọn itọpa ifihan agbara labẹ module lori Layer nibiti module ti gbe.

10.3.2 RF Layout Awọn iṣeduro
O ṣe pataki pe apakan RF wa ni titọ ni deede lati rii daju iṣẹ module ti o dara julọ. Ifilelẹ ti ko dara le fa agbara iṣelọpọ kekere ati ibajẹ ifamọ. olusin 10-2 fihan RF placement ati afisona ti awọn module pẹlu 2.4-GHz inverted F eriali.

Tẹle awọn iṣeduro ifilelẹ RF wọnyi fun module:

Awọn itọpa RF gbọdọ ni ikọlu abuda ti 50-Ω.
Ko si awọn itọpa tabi ilẹ labẹ apakan eriali.
Awọn itọpa RF gbọdọ ni nipasẹ aranpo lori ọkọ ofurufu ilẹ lẹba itọpa RF ni ẹgbẹ mejeeji.
Awọn itọpa RF gbọdọ jẹ kukuru bi o ti ṣee ṣe.
Ẹya ara ẹrọ gbọdọ wa ni isunmọ si eti PCB ni akiyesi ibi-ipamọ ọja ati iru eriali ti a lo.

10.3.2.1 Eriali Ibi ati afisona
Eriali jẹ eroja ti a lo lati yi awọn igbi itọsọna pada lori awọn itọpa PCB si itọsi itanna aaye ọfẹ. Ibi ati ifilelẹ ti eriali jẹ awọn bọtini si ibiti o pọ si ati awọn oṣuwọn data. Tabili 10-2 n pese akojọpọ awọn itọnisọna eriali lati tẹle pẹlu CC1312PSIPmodule.

Table 10-2. Awọn Itọsọna Antenna

SR KO.	Awọn Ilana Itọsọna
1	Gbe eriali si eti PCB.
2	Rii daju wipe ko si awọn ifihan agbara ti wa ni ipa lori awọn eroja eriali lori eyikeyi PCB Layer.
3	Pupọ awọn eriali, pẹlu eriali PCB ti a lo lori LaunchPad™, nilo imukuro ilẹ lori gbogbo awọn ipele ti PCB. Rii daju pe ilẹ ti wa ni idasilẹ lori awọn ipele inu bi daradara.
4	Rii daju pe ipese wa lati gbe awọn paati ibamu fun eriali naa. Awọn wọnyi gbọdọ wa ni aifwy fun ti o dara ju pada pipadanu nigbati awọn pipe ọkọ ti wa ni jọ. Eyikeyi pilasitik tabi casing gbọdọ tun ti wa ni agesin nigba ti yiyi eriali nitori eyi le ikolu awọn ikọjujasi.
5	Rii daju pe ikọlu abuda eriali jẹ 50-Ω bi module ti ṣe apẹrẹ fun eto 50-Ω.
6	Ni irú ti tejede eriali, rii daju wipe kikopa wa ni ošišẹ ti considering soldermask sisanra.
7	Fun iṣẹ ṣiṣe RF ti o dara ṣe idaniloju pe Voltge Standing Wave Ration (VSWR) kere ju 2 kọja iye igbohunsafẹfẹ ti iwulo.
9	Ojuami kikọ sii ti eriali ni a nilo lati wa ni ilẹ. Eyi jẹ nikan fun iru eriali ti a lo lori LP-EM-CC1312PSIP LaunPad™. Wo awọn iwe data eriali pato fun awọn iṣeduro.

Tabili 10-3 ṣe atokọ awọn eriali ti a ṣeduro lati lo pẹlu CC1312PSIPmodule. Awọn eriali miiran le wa fun lilo pẹlu CC1312PSIPmodule. Jọwọ tọkasi lati awọn fun akojọ kan ti a fọwọsi eriali (ati eriali orisi) ti o le ṣee lo pẹlu CC1312PSIP module.
Table 10-3. Niyanju Eriali

Àyànfẹ́	ANTENNA	Olupese	AKIYESI
1	Ese PCB eriali lori LP-EM- CC1312PSIP	Texas Instruments	+ 2.7 dBi ere ni 915 MHz, wo apẹrẹ itọkasi LP-EM-CC1312PSIP
2	Ita okùn eriali	nitosi, S463AM-915	+ 2.0 dBi ere ni 915 MHz, https://www.nearson.com/assets/pdfs/Antenna/S463XX-915.pdf,
3	Ita okùn eriali	Pulse, W5017	+ 0.9 dBi anfani ni 915 MHz
4	Chip eriali	Johanson Technology, 0900AT43A0070	-0.5 dBi anfani ni 915 MHz
5	Chip eriali	Johanson Technology, 0915AT43A0026	+ 1.4 dBi anfani ni 915 MHz
6	Helical waya eriali	Pulse, W3113	+ 0.8 dBi anfani ni 915 MHz

10.3.2.2 Gbigbe Line ero
Awọn ifihan agbara RF lati module ti wa ni ipa si eriali lilo a Coplanar Waveguide pẹlu ilẹ (CPW-G). Eto CPW-G nfunni ni iye ti o pọju ti ipinya ati aabo ti o dara julọ ti o ṣeeṣe si awọn laini RF. Ni afikun si ilẹ lori Layer L1, gbigbe GND vias lẹgbẹẹ laini tun pese aabo aabo.
olusin 10-3 fihan a agbelebu apakan ti awọn coplanar waveguide pẹlu awọn lominu ni mefa.
olusin 10-4 fihan awọn oke view ti coplanar waveguide pẹlu GND ati nipasẹ stitching.

Awọn iye iṣeduro fun igbimọ PCB 4-Layer ti pese ni Tabili 10-4.
Table 10-4. Niyanju PCB iye fun 4-Layer
Ọkọ (L1 si L2 = 0.175 mm)

10.4 Awọn apẹrẹ itọkasi
Awọn apẹrẹ itọkasi atẹle yẹ ki o tẹle ni pẹkipẹki nigbati o ba n ṣe awọn apẹrẹ nipa lilo ẹrọ CC1312PSIP.
Ifarabalẹ pataki gbọdọ wa ni san si gbigbe awọn paati RF, awọn olutọpa decoupling ati awọn paati olutọsọna DCDC, bakanna bi awọn asopọ ilẹ fun gbogbo iwọnyi.

LP-EM-CC1312PSIP
Apẹrẹ Files

Apẹrẹ itọkasi LP-EM-CC1312PSIP n pese apẹrẹ, ipilẹ ati iṣelọpọ files fun awọn karakitariasesonu ọkọ ti a lo fun nianfani nọmba išẹ ri ni yi iwe.

Iha-1 GHz ati 2.4 GHz Antenna Apo fun
Ohun elo Idagbasoke LaunchPad™ ati sensọTag

Ohun elo eriali ngbanilaaye idanwo igbesi aye gidi lati ṣe idanimọ eriali ti o dara julọ fun ohun elo rẹ. Ohun elo eriali naa pẹlu awọn eriali 16 fun awọn loorekoore lati 169 MHz si 2.4 GHz, pẹlu:
• PCB eriali
• Helical eriali
• Chip eriali
• Awọn eriali meji-band fun 868 MHz ati 915 MHz ni idapo pelu 2.4 GHz Ohun elo eriali pẹlu okun JSC kan lati sopọ si Awọn ohun elo Idagbasoke MCU Alailowaya MCU LaunchPad ati SensọTags.

Awọn ibeere Ayika ati Awọn pato SMT

11.1 PCB atunse
PCB naa tẹle IPC-A-600J fun lilọ PCB ati oju-iwe ogun <0.75% tabi 7.5 mil fun inch.
11.2 mimu Ayika
11.2.1 ebute
Awọn ọja ti wa ni agesin pẹlu modaboudu nipasẹ ilẹ-akoj orun (LGA). Lati ṣe idiwọ titaja ti ko dara, maṣe kan si awọ ara pẹlu apakan LGA.
11.2.2 isubu
Awọn paati ti a gbe soke yoo bajẹ ti ọja ba ṣubu tabi ti lọ silẹ. Iru ibajẹ le fa ọja naa si aiṣedeede.
11.3 Ibi ipamọ Ipò
11.3.1 Ọrinrin Idankan apo Ṣaaju Ṣii
Apo idena ọrinrin gbọdọ wa ni ipamọ ni iwọn otutu ti o kere ju 30°C pẹlu ọriniinitutu labẹ 85% RH. Igbesi aye selifu ti a ṣe iṣiro fun ọja ti o ti gbẹ yoo jẹ oṣu 24 lati ọjọ ti a ti di apo naa.
11.3.2 Ọrinrin Idankan Bag Ṣii
Awọn kaadi itọkasi ọriniinitutu gbọdọ jẹ buluu, <30%.
11.4 PCB Apejọ Itọsọna
Awọn modulu MCU alailowaya ti wa ni akopọ ni ipilẹ sobusitireti Leadless Quad Flatpack (QFM) package. Awọn modulu ti wa ni apẹrẹ pẹlu fa awọn itọsọna pada fun ipilẹ PCB ti o rọrun ati iṣagbesori igbimọ.
11.4.1 PCB Land Àpẹẹrẹ & gbona Vias
A ṣeduro boju-boju ti o ta ọja ti o ṣalaye ilana ilẹ lati pese iwọn paadi solder deede lati le gba iwọntunwọnsi solder to dara julọ ati igbẹkẹle apapọ solder. PCB ilẹ Àpẹẹrẹ ni o wa 1: 1 to module soldering pad apa miran. Awọn ọna igbona lori PCB ti a ti sopọ si ọkọ ofurufu irin miiran jẹ fun idinaduro igbona. O ṣe pataki lati ni awọn ọna igbona ti o to lati yago fun tiipa igbona ẹrọ. Iwọn nipasẹs ti a ṣe iṣeduro jẹ 0.2mm ati ipo kii ṣe taara labẹ lẹẹmọ tita lati yago fun sisọ solder sinu vias.
11.4.2 SMT Apejọ Awọn iṣeduro
Awọn iṣẹ iṣakojọpọ dada module pẹlu:

Iboju titẹ sita lẹẹmọ solder lori PCB
Bojuto iwọn didun lẹẹ tita (aṣọkan)
Package placement lilo boṣewa SMT placement ẹrọ
Ayẹwo X-ray ṣaaju-atunṣe – lẹẹ afara
Atunse
Ayẹwo X-ray lẹhin-atunse – solder bridge ati ofo

11.4.3 PCB dada Ipari ibeere
A aṣọ PCB plating sisanra jẹ bọtini fun ga ijọ ikore. Fun ipari goolu immersion nickel ti ko ni elekitiroti, sisanra goolu yẹ ki o wa lati 0.05 µm si 0.20 µm lati yago fun isọdọkan solder. Lilo PCB kan pẹlu Organic Solderability Preservative (OSP) ipari ti a bo ni a tun ṣe iṣeduro bi yiyan si Ni-Au.

11.4.4 Solder Stencil
Isọsọsọ lẹẹ solder ni lilo ilana titẹ stencil kan pẹlu gbigbe lẹẹmọ tita nipasẹ awọn iho ti a ti yan tẹlẹ pẹlu ohun elo titẹ. Awọn paramita Stencil gẹgẹbi ipin agbegbe iho ati ilana iṣelọpọ ni ipa pataki lori ifisilẹ lẹẹmọ. Ayewo ti stencil ṣaaju si ipo ti package jẹ iṣeduro gaan lati mu ilọsiwaju awọn ikojọpọ igbimọ igbimọ.
11.4.5 Package Placement
Awọn idii le ṣee gbe ni lilo yiyan boṣewa ati ohun elo ibi pẹlu deede ± 0.05 mm. Awọn ọna gbigbe ati ibi ti paati jẹ akojọpọ eto iran ti o ṣe idanimọ ati ipo paati ati eto ẹrọ ti o n ṣe iṣẹ gbigbe ati ibi ti ara. Awọn ọna ṣiṣe iriran meji ti o wọpọ ni:

Eto iran ti o wa ojiji biribiri package kan
Eto iran ti o wa awọn paadi kọọkan lori ilana isọpọ

Iru keji n pese awọn aye deede diẹ sii ṣugbọn o duro lati jẹ gbowolori diẹ sii ati gbigba akoko. Awọn ọna mejeeji jẹ itẹwọgba nitori awọn apakan ti o ṣe deede nitori awọn ẹya ara ẹni ti ara ẹni ti apapọ solder lakoko isọdọtun solder. A gbaniyanju lati yago fun gbigbe solder si 2 mils sinu lẹẹ tita tabi pẹlu ipa ti o kere ju lati yago fun ibajẹ eyikeyi ti o ṣeeṣe si awọn idii tinrin.
11.4.6 Solder Joint ayewo
Lẹhin apejọ oke dada, X-ray gbigbe yẹ ki o lo fun sample monitoring ti solder asomọ ilana. Eyi n ṣe idanimọ awọn abawọn bii gbigbẹ tita, awọn kuru, ṣiṣi, ati ofo. O tun ṣe iṣeduro lati lo ẹgbẹ view ayewo ni afikun si X-ray lati mọ ti o ba ti wa ni "Wakati Gilasi" sókè solder ati package pulọgi si tẹlẹ. Awọn apẹrẹ ti o ta "Wakati Gilasi" kii ṣe asopọ ti o gbẹkẹle. Isọtẹlẹ digi 90° le ṣee lo fun ẹgbẹ view ayewo.
11.4.7 Atunse ati Rirọpo
TI ṣeduro yiyọkuro awọn modulu nipasẹ ibudo atunṣiṣẹ kan ti o lo profile iru si awọn iṣagbesori ilana. Lilo ibon igbona le fa ibajẹ si module nigbakan nipasẹ igbona.
11.4.8 Solder Joint Voiding
TI ṣe iṣeduro lati ṣakoso isọpọ solder solder lati jẹ kere ju 30% (fun IPC-7093). Awọn ofo apapọ solder le dinku nipasẹ didin ti awọn paati ati PCB, idinku akoko ifihan lẹẹmọ tita, ati isọdọtun profile iṣapeye.
11.5 yan Awọn ipo
Awọn ọja nilo yan ṣaaju iṣagbesori ti:

Awọn kaadi itọkasi ọriniinitutu ti ka> 30%
Iwọn otutu <30°C, ọriniinitutu <70% RH, ju wakati 96 lọ
Ipo ndin: 90 ° C, 12 si 24 wakati
Awọn akoko yan: 1 akoko

11.6 Soldering ati reflow Ipò

Ọna gbigbona: Convection ti aṣa tabi IR convection
Iwọn iwọn otutu: Thermocouple d = 0.1 mm si 0.2 mm CA (K) tabi CC (T) ni ipin tita tabi ọna deede
Solder lẹẹ tiwqn: SAC305
Allowable reflow soldering igba: 2 igba da lori reflow soldering profile (wo aworan 11-1)
Awọn iwọn otutu profile: Reflow soldering yoo ṣee ṣe ni ibamu si awọn iwọn otutu profile (wo aworan 11-1)
Iwọn otutu ti o ga julọ: 260°Colusin 11-1. Iwọn otutu Profile fun Akojopo Solder Heat Resistance ti a paati (ni Solder Joint)

Table 11-1. Iwọn otutu Profile

Profile Awọn eroja	Convection tabi IR(1)
Iwọn otutu ti o ga julọ	235 si 240°C aṣoju (o pọju 260°C)
Ṣaaju-ooru / Ríiẹ (150 si 200 ° C)	60 si 120 aaya
Akoko loke yo ojuami	60 si 90 aaya
Akoko pẹlu 5 ° C si tente	30 aaya ti o pọju
Ramp up	<3°C / iṣẹju-aaya
Ramp isalẹ	<-6°C / iṣẹju-aaya

(1) Fun awọn alaye, tọka si iṣeduro ti olupese lẹẹ lẹẹmọ.

Akiyesi
TI ko ṣeduro lilo ibora ti o ni ibamu tabi ohun elo ti o jọra lori module SimpleLink™.
Ibora yii le ja si aapọn agbegbe lori awọn asopọ solder inu module ati ni ipa igbẹkẹle module. Lo iṣọra lakoko ilana apejọ module si PCB ikẹhin lati yago fun wiwa awọn ohun elo ajeji inu module.

Ẹrọ ati Iwe Atilẹyin

TI nfunni ni laini nla ti awọn irinṣẹ idagbasoke. Awọn irinṣẹ ati sọfitiwia lati ṣe iṣiro iṣẹ ṣiṣe ti ẹrọ, ṣe ipilẹṣẹ koodu, ati idagbasoke awọn solusan ti wa ni atokọ bi atẹle.

12.1 Device Nomenclature
Lati ṣe apẹrẹ awọn stages ni ọmọ idagbasoke ọja, TI ṣe ipinnu awọn asọtẹlẹ si gbogbo awọn nọmba apakan ati/tabi koodu ọjọ.
Ẹ̀rọ kọ̀ọ̀kan ní ọ̀kan nínú àwọn ìpele mẹ́ta/mẹ́ta ìdámọ̀: X, P, tàbí asán (kò sí ìpele ìpele) (fun ex.ample, XCC1312PSIP wa ni iṣaajuview; nitorina, a fi ami-iṣaaju X/idamọ sọtọ).
Sisan itiranya idagbasoke ẹrọ:
Ẹrọ idanwo X ti kii ṣe aṣoju dandan ti awọn pato itanna ẹrọ ikẹhin ati pe o le ma lo ṣiṣan apejọ iṣelọpọ.
Ẹrọ Afọwọkọ P ti kii ṣe dandan pe ohun alumọni ti o kẹhin ku ati pe o le ma pade awọn pato itanna ikẹhin.
Ẹya iṣelọpọ asan ti ohun alumọni kú ti o jẹ oṣiṣẹ ni kikun.
Awọn ẹrọ iṣelọpọ ti ṣe afihan ni kikun, ati pe didara ati igbẹkẹle ẹrọ naa ti ṣafihan ni kikun. Atilẹyin boṣewa TI kan.
Awọn asọtẹlẹ fihan pe awọn ẹrọ apẹrẹ (X tabi P) ni oṣuwọn ikuna ti o tobi ju awọn ẹrọ iṣelọpọ boṣewa lọ. Texas Instruments ṣe iṣeduro pe awọn ẹrọ wọnyi ko ṣee lo ni eyikeyi eto iṣelọpọ nitori pe oṣuwọn ikuna lilo ipari ti wọn nireti ṣi jẹ aisọye. Awọn ẹrọ iṣelọpọ ti o peye nikan ni o yẹ ki o lo.
TI ẹrọ nomenclature tun pẹlu kan suffix pẹlu awọn ẹrọ ebi orukọ. Suffix yii tọkasi iru package (fun example, RGZ).
Fun awọn nọmba apakan ti a le paṣẹ ti awọn ẹrọ CC1312PSIP ni iru package RGZ (7-mm x 7-mm), wo Atunkun Aṣayan Package ti iwe yii, Alaye Ẹrọ ni Abala 3, TI webAaye (www.ti.com), tabi kan si aṣoju tita TI rẹ.

12.2 Irinṣẹ ati Software
Ẹrọ CC1312PSIP ni atilẹyin nipasẹ ọpọlọpọ sọfitiwia ati awọn irinṣẹ idagbasoke ohun elo.
Idagbasoke Apo
Software

SimpleLink™ CC13xx ati CC26xx Software

Ohun elo Idagbasoke sọfitiwia SimpleLink CC13xx-CC26xx (SDK) pese pipe
package fun idagbasoke awọn ohun elo alailowaya lori idile CC13x2 / CC26x2

Apo Idagbasoke (SDK)

ti awọn ẹrọ. SDK naa pẹlu package sọfitiwia pipe fun ẹrọ CC1312PSIP, pẹlu awọn akopọ ilana atẹle wọnyi:
Wi-SUN®
• TI 15.4-Stack – ojuutu nẹtiwọki irawọ orisun IEEE 802.15.4 fun Sub-1 GHz ati 2.4 GHz
• Prop RF API – eto ti o rọ ti awọn bulọọki ile fun idagbasoke awọn akopọ sọfitiwia RF ohun-ini SimpleLink CC13xx-CC26xx SDK jẹ apakan ti Syeed SimpleLink MCU TI ti TI, ti o funni ni agbegbe idagbasoke kan ti o nfi ohun elo rọ, sọfitiwia ati awọn aṣayan irinṣẹ fun awọn alabara ti o dagbasoke ti firanṣẹ ati alailowaya ohun elo.
Fun alaye diẹ sii nipa SimpleLink MCU Platform, ṣabẹwo https://www.ti.com/simplelink.

Awọn Irinṣẹ Idagbasoke

Olupilẹṣẹ koodu Studio™ Ti ṣepọ Idagbasoke Ayika (IDE)	Studio Olupilẹṣẹ koodu jẹ agbegbe idagbasoke ti irẹpọ (IDE) ti o ṣe atilẹyin Microcontroller TI ati portfolio Awọn ilana ti a fi sii. Studio Olupilẹṣẹ koodu ni akojọpọ awọn irinṣẹ ti a lo lati ṣe agbekalẹ ati ṣatunṣe awọn ohun elo ifibọ. O pẹlu olupilẹṣẹ C/C++ ti o dara ju, olootu koodu orisun, agbegbe ikole iṣẹ akanṣe, atunkọ, profiler, ati ọpọlọpọ awọn miiran awọn ẹya ara ẹrọ. IDE ogbon inu n pese wiwo olumulo kan ti o mu ọ nipasẹ igbesẹ kọọkan ti ṣiṣan idagbasoke ohun elo. Awọn irinṣẹ ti o mọ ati awọn atọkun gba awọn olumulo laaye lati bẹrẹ ni iyara ju ti tẹlẹ lọ. Code Olupilẹṣẹ Studio daapọ advantages ti ilana sọfitiwia Eclipse® pẹlu awọn agbara yokokoro ti o ni ilọsiwaju ti o ni ilọsiwaju lati ọdọ TI ti o yorisi agbegbe idagbasoke ẹya-ara ti o lagbara fun awọn olupilẹṣẹ ifibọ. CCS ni atilẹyin fun gbogbo awọn MCU Alailowaya SimpleLink ati pẹlu atilẹyin fun sọfitiwia EnergyTrace™ (profaili lilo agbara ohun elo). Ohun gidi-akoko viewer itanna wa fun TI-RTOS, apakan ti SimpleLink SDK. Studio Olupilẹṣẹ koodu ti pese ni ọfẹ nigbati o ba lo ni apapo pẹlu awọn apanirun XDS ti o wa lori Apo Idagbasoke LaunchPad kan.
Olupilẹṣẹ koodu Studio™ awọsanma IDE	Code Olupilẹṣẹ Studio (CCS) Awọsanma ni a webIDE orisun ti o fun ọ laaye lati ṣẹda, ṣatunkọ ati kọ CCS ati awọn iṣẹ akanṣe Energia ™. Lẹhin ti o ti kọ iṣẹ akanṣe rẹ ni aṣeyọri, o le ṣe igbasilẹ ati ṣiṣẹ lori LaunchPad ti o sopọ. N ṣatunṣe aṣiṣe ipilẹ, pẹlu awọn ẹya bii eto awọn aaye fifọ ati viewAwọn iye oniyipada ni atilẹyin ni bayi pẹlu CCS Cloud.
IAR Ifibọ Ibujoko iṣẹ® fun Apa®	IAR Embedded Workbench® jẹ eto awọn irinṣẹ idagbasoke fun kikọ ati ṣatunṣe awọn ohun elo eto ifibọ nipa lilo apejọ, C ati C ++. O pese agbegbe idagbasoke imudara patapata ti o pẹlu oluṣakoso ise agbese, olootu, ati awọn irinṣẹ kọ. IAR ni atilẹyin fun gbogbo SimpleLink Alailowaya MCUs. O funni ni atilẹyin yokokoro gbooro, pẹlu XDS110, IAR I-jet™ ati Segger J-Link™. Ohun gidi-akoko viewer itanna wa fun TI-RTOS, apakan ti SimpleLink SDK. IAR tun ṣe atilẹyin jade-ti-apoti lori ọpọlọpọ sọfitiwia examples pese bi apakan ti SimpleLink SDK. Igbelewọn ọjọ 30 tabi ẹya iwọn-iwọn 32 KB wa nipasẹ iar.com.
SmartRF™ Studio	SmartRF™ Studio jẹ ohun elo Windows® ti o le ṣee lo lati ṣe iṣiro ati tunto SimpleLink Alailowaya MCUs lati Texas Instruments. Ohun elo naa yoo ṣe iranlọwọ fun awọn apẹẹrẹ ti awọn eto RF lati ṣe iṣiro redio ni irọrun ni kutukutu stage ninu ilana apẹrẹ. O wulo paapaa fun iran ti awọn iye iforukọsilẹ iṣeto ni ati fun idanwo iṣe ati ṣiṣatunṣe ti eto RF. Studio SmartRF le ṣee lo boya bi ohun elo adaduro tabi papọ pẹlu awọn igbimọ igbelewọn to wulo tabi awọn iwadii yokokoro fun ẹrọ RF. Awọn ẹya ara ẹrọ SmartRF Studio pẹlu: Awọn idanwo ọna asopọ – firanṣẹ ati gba awọn apo-iwe wọle laarin awọn apa

12.2.1 SimpleLink™ Microcontroller Platform
Syeed microcontroller SimpleLink ṣeto idiwọn tuntun fun awọn olupilẹṣẹ pẹlu portfolio gbooro ti onirin ati Apa alailowaya
Awọn MCU (System-on-Chip) ni agbegbe idagbasoke sọfitiwia kan ṣoṣo. Gbigbe ohun elo to rọ, sọfitiwia ati awọn aṣayan irinṣẹ fun awọn ohun elo IoT rẹ. Ṣe idoko-owo lẹẹkan ninu ohun elo idagbasoke sọfitiwia SimpleLink ati lo jakejado gbogbo portfolio rẹ. Kọ ẹkọ diẹ sii lori ti.com/simplelink.

12.3 Iwe Support

Lati gba iwifunni ti awọn imudojuiwọn iwe lori awọn iwe data, errata, awọn akọsilẹ ohun elo ati iru, lilö kiri si folda ọja ẹrọ lori ti.com/product/CC1312PSIP. Ni igun apa ọtun oke, tẹ Itaniji mi lati forukọsilẹ ati gba iṣiro ọsẹ kan ti eyikeyi alaye ọja ti o ti yipada. Fun awọn alaye iyipada, tunview itan atunyẹwo ti o wa ninu eyikeyi iwe ti a tunwo.
Awọn iwe-ipamọ lọwọlọwọ ti o ṣe apejuwe MCU, awọn agbeegbe ti o jọmọ, ati iwe adehun imọ-ẹrọ miiran jẹ atokọ bi atẹle.

TI oluşewadi Explorer
TI oluşewadi Explorer
Software examples, ikawe, executables, ati iwe wa o si wa fun ẹrọ rẹ ati idagbasoke ọkọ.

Erratum

CC1312PSIP ohun alumọni Erratum

Errata silikoni ṣe apejuwe awọn imukuro ti a mọ si awọn pato iṣẹ ṣiṣe fun atunyẹwo ohun alumọni kọọkan ti ẹrọ naa ati apejuwe bi o ṣe le ṣe idanimọ atunyẹwo ẹrọ kan.

Ohun elo Iroyin
Gbogbo awọn ijabọ ohun elo fun ẹrọ CC1312PSIP ni a rii lori folda ọja ẹrọ ni: ti.com/product/CC1312PSIP/technicaldocuments.
Ilana Itọkasi Imọ-ẹrọ (TRM)
CC13x2, CC26x2 SimpleLink™ Alailowaya MCU TRM

TRM n pese alaye alaye ti gbogbo awọn modulu ati awọn agbeegbe ti o wa ninu ẹbi ẹrọ.

12.4 Support Resources
support forum jẹ orisun ẹlẹrọ kan fun iyara, awọn idahun ti a rii daju ati iranlọwọ apẹrẹ - taara lati ọdọ awọn amoye. Wa awọn idahun ti o wa tẹlẹ tabi beere ibeere tirẹ lati gba iranlọwọ oniru iyara ti o nilo. ™ Akoonu ti o somọ ti pese AS WA” nipasẹ awọn oluranlọwọ. Wọn ko jẹ awọn pato TI ati pe ko ṣe afihan ti TI dandan views; wo Awọn ofin Lilo TI. 12.5 Awọn aami-iṣowo jẹ aami-iṣowo ti Texas Instruments. I-jet SimpleLink ™ , LaunchPad ™ , Code Composer Studio ™ , EnergyTrace ™ , ati TI E2E ™ jẹ aami-iṣowo ti IAR Systems AB. J-Link ™ jẹ aami-iṣowo ti SEGGER Microcontroller Systeme GmbH. Arm ™ jẹ aami-išowo ti a forukọsilẹ ti Arm Limited (tabi awọn ẹka rẹ) ni AMẸRIKA ati/tabi ibomiiran. CoreMark ® ati Cortex ® tr ictio ns jẹ aami-išowo ti a forukọsilẹ ti Ifibọ Microprocessor Benchmark Consortium Corporation. Arm Thumb ® jẹ aami-išowo ti a forukọsilẹ ti Arm Limited (tabi awọn ẹka rẹ). Eclipse ® jẹ aami-iṣowo ti a forukọsilẹ ti Eclipse Foundation. IAR ifibọ Workbench ® jẹ aami-iṣowo ti a forukọsilẹ ti IAR Systems AB. Windows ® jẹ aami-iṣowo ti a forukọsilẹ ti Microsoft Corporation. Gbogbo awọn aami-išowo jẹ ohun-ini ti awọn oniwun wọn. ®
12.6 Electrostatic Sisọ Išọra

12.6 Electrostatic Sisọ Išọra
Yi ese Circuit le bajẹ nipa ESD. Texas Instruments ṣe iṣeduro pe gbogbo awọn iyika iṣọpọ ni a mu pẹlu awọn iṣọra ti o yẹ. Ikuna lati ṣe akiyesi mimu to dara ati awọn ilana fifi sori ẹrọ le fa ibajẹ.
Ibajẹ ESD le wa lati ibajẹ iṣẹ ṣiṣe arekereke lati pari ikuna ẹrọ. Awọn iyika iṣọpọ pipe le jẹ ifaragba si ibajẹ nitori awọn iyipada parametric kekere le fa ki ẹrọ naa ko ni ibamu pẹlu awọn pato ti a tẹjade.
12.7 Gilosari
TI Gilosari
Gilosari yii ṣe atokọ ati ṣalaye awọn ofin, awọn adape, ati awọn itumọ.

Mechanical, Iṣakojọpọ, ati Alaye ti o paṣẹ

Awọn oju-iwe atẹle pẹlu iṣakojọpọ ẹrọ ati alaye ti o le paṣẹ. Alaye yii jẹ data lọwọlọwọ julọ ti o wa fun awọn ẹrọ ti a yan. Data yii jẹ koko ọrọ si iyipada laisi akiyesi ati atunyẹwo iwe yii. Fun awọn ẹya orisun ẹrọ aṣawakiri ti iwe data yii, tọka si lilọ kiri ọwọ osi.
Akiyesi
Awọn lapapọ iga ti awọn module ni 1.51 mm.
Iwọn ti module CC1312PSIP jẹ deede 0.19 g.

AKIYESI:

Gbogbo awọn iwọn laini wa ni millimeters. Eyikeyi awọn iwọn ni akọmọ jẹ fun itọkasi nikan. Dimensioning ati ifarada fun ASME Y14.5M.
Iyaworan yii jẹ koko ọrọ si iyipada laisi akiyesi.
EXAMPLE BOARD LAYOUT QFM - 1.51 mm max iga
MOT0048A
A ṣe apẹrẹ package yii lati ta si paadi igbona lori ọkọ. Fun alaye diẹ sii, wo nọmba litireso Texas Instruments SLUA271 (www.ti.com/lit/slua271).
Awọn iho gige lesa pẹlu awọn odi trapezoidal ati awọn igun yika le funni ni idasilẹ lẹẹmọ dara julọ. IPC-7525 le ni awọn iṣeduro apẹrẹ miiran.

AKIYESI PATAKI ATI ALAYE

TI n pese data imọ-ẹrọ ati igbẹkẹle (pẹlu awọn iwe data), Awọn orisun apẹrẹ (pẹlu awọn apẹrẹ itọkasi), Ohun elo tabi imọran apẹrẹ miiran, WEB Awọn irinṣẹ, ALAYE Aabo, Ati awọn orisun miiran “BI o ti ri” ATI PẸLU GBOGBO AWỌN AṢẸ, ATI PẸLU GBOGBO awọn ATILẸYIN ỌJA, KIAKIA ATI ITOJU, PẸLU LAISI OPIN KANKAN ATILẸYIN ỌJA TI ỌLỌJA, AGBARA FUN AGBẸRẸ. .
Awọn orisun wọnyi jẹ ipinnu fun awọn oludasilẹ ti oye ti n ṣe apẹrẹ pẹlu awọn ọja TI. Iwọ nikan ni o ni iduro fun (1) yiyan awọn ọja TI ti o yẹ fun ohun elo rẹ, (2) ṣe apẹrẹ, ijẹrisi ati idanwo ohun elo rẹ, ati (3) rii daju pe ohun elo rẹ ni ibamu pẹlu awọn iṣedede iwulo, ati eyikeyi aabo, aabo, ilana tabi awọn ibeere miiran. .
Awọn orisun wọnyi jẹ koko ọrọ si iyipada laisi akiyesi. TI fun ọ ni igbanilaaye lati lo awọn orisun wọnyi nikan fun idagbasoke ohun elo kan ti o nlo awọn ọja TI ti a ṣalaye ninu awọn orisun. Atunse miiran ati ifihan awọn orisun wọnyi jẹ eewọ. Ko si iwe-aṣẹ ti a fun ni eyikeyi ẹtọ ohun-ini imọ-ọgbọn TI miiran tabi si eyikeyi ẹtọ ohun-ini ọgbọn ti ẹnikẹta. TI ko ni ẹtọ fun, ati pe iwọ yoo jẹri fun TI ni kikun ati awọn aṣoju rẹ lodi si, eyikeyi awọn ẹtọ, awọn bibajẹ, awọn idiyele, awọn adanu, ati awọn gbese ti o dide nipa lilo awọn orisun wọnyi.
Awọn ọja TI ti pese labẹ Awọn ofin Tita ti TI tabi awọn ofin iwulo miiran ti o wa boya lori ti.com tabi pese ni apapo pẹlu iru awọn ọja TI. Ipese TI ti awọn orisun wọnyi ko faagun tabi bibẹẹkọ paarọ awọn iṣeduro iwulo TI tabi awọn idawọle atilẹyin ọja fun awọn ọja TI.
TI ṣe ohun si ati kọ eyikeyi afikun tabi awọn ofin oriṣiriṣi ti o le ti daba.
AKIYESI PATAKI Adirẹsi Ifiweranṣẹ: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Aṣẹ-lori-ara © 2023, Texas Instruments Incorporated

Aṣẹ-lori-ara © 2023 Texas Instruments Incorporated
Ọja Folda Links: CC1312PSIP
Fi Esi iwe aṣẹ silẹ
www.ti.com

Awọn iwe aṣẹ / Awọn orisun

Awọn irinṣẹ TEXAS CC1312PSIP SimpleLink Sub-1-GHz Eto Alailowaya-ni-package [pdf] Afọwọkọ eni
CC1312PSIP SimpleLink Sub-1-GHz Eto Alailowaya-ninu-Package, CC1312PSIP, SimpleLink Sub-1-GHz Eto Alailowaya-ninu-Package, Sub-1-GHz System-in-Package, System-in-Package, System- ni-Package

Awọn itọkasi

Itọsọna olumulo

Awọn ẹya ara ẹrọ