TEXAS INSTRUMENTS CC1312PSIP SimpleLink Sub-1-GHz Wireless System-in-Package Bukana ea Mong'a

Mokhanni oa Dynamic multiprotocol manager (DMM).
Seea-le-moea se hlophisitsoeng se kenyelletsa tšehetso bakeng sa 2(G)FSK, 4-(G)FSK, MSK, OOK, IEEE 802.15.4 PHY le MAC

E ts'ehetsa taolo ea sensor ea matla a holimo holimo (OTA) Ultra-low power sensor
Autonomous MCU e nang le 4KB ea SRAM

Sampboloka, 'me u sebetse data ea sensor
Ho tsoha kapele bakeng sa ts'ebetso ea matla a tlase

Software hlalosoa peripherals; capacitive touch, meter ea phallo,
LCD Tšebeliso e tlase ea matla
Tšebeliso ea MCU: - 2.9 mA mokhoa o sebetsang, CoreMark ®
- 60 μA/MHz e tsamaisang CoreMark®
- 0.9 μA boemo ba standby, RTC, 80KB RAM
- 0.1 μA mokhoa oa ho koala, ho tsoha ka phini

Tšebeliso ea li-sensor tse matla a tlase haholo:
- 30 μA ka mokhoa oa 2-MHz
- 808 μA ka mokhoa oa 24-MHz
Tšebeliso ea Radio:
- 5.8-mA RX ho 868 MHz
- 28.7-mA TX ho +14 dBm ho 868 MHz
Ts'ehetso ea protocol e se nang mohala

Wi-SUN®
mioty®

Wireless M-Bus
SimpleLink™ TI 15.4-stack

6LoWPAN
Litsamaiso tsa thepa seea-le-moea se sebetsang hantle

-119 dBm bakeng sa mofuta o molelele oa 2.5-kbps
-108 dBm ho 50 kbps, 802.15.4, 868 MHz
Ho latela melao

E netefalitsoe esale pele bakeng sa:
– FCC CFR47 Karolo ea 15
E loketse litsamaiso tse shebaneng le ho latela:
– ETSI EN 300 220 Receiver Cat. 1.5 le 2, EN 303 131, EN 303 204
– ARIB STD-T108
Setšoantšo sa MCU

Lisebelisoa tsa dijithale li ka tsamaisoa ho 30 GPIOs
Linako tse 'ne tsa 32-bit kapa tse robeli tsa 16-bit ka kakaretso

12-bit ADC, 200 kSampbonyane/s, likanale tse 8
8-bit DAC

Bapisa ba babeli
Mohloli oa hona joale o hlophisitsoeng
Li-UART tse peli, SSI tse peli, I
Oache ea nako ea 'nete (RTC)
Mocheso o kopantsoeng le mochine oa betri
Lisebelisoa tsa ts'ireletso
AES 128- le 256-bit cryptographic accelerator
ECC le RSA public key hardware accelerator
SHA2 Accelerator (setupo se felletseng ho fihla ho SHA-512)
Jenereithara ea 'nete ea linomoro tse sa reroang (TRNG)
Lisebelisoa tsa ntlafatso le software
Lethathamo la lintlha tsa LP-CC1312PSIP
SimpleLink™ CC13xx le CC26xx Software
Development Kit (SDK)
SmartRF™ Studio bakeng sa tlhophiso e bonolo ea radio
Sensor Controller Studio bakeng sa ho haha lisebelisoa tse nang le matla a tlase
Sesebelisoa sa ho hlophisa sistimi ea SysConfig
Sebaka sa ts'ebetso
1.8-V ho isa ho 3.8-V phepelo e le 'ngoetage
-40 ho ea ho +105°C (+14 dBm PA)
Likarolo tsohle tse hlokahalang li kopantsoe
kristale ea 48-MHz: Ho nepahala ha RF ± 10 ppm

kristale ea 32-kHz: Ho nepahala ha RTC ± 50 ppm
Lisebelisoa tsa converter tsa DC / DC le li-decoupling capacitor
Likarolo tse ka pele tsa RF tse nang le tlhahiso ea 50-Ohm
Sephutheloana

7-mm × 7-mm MOT (30 GPIOs)
Pin-to-pin e tsamaellana le CC2652RSIP le CC2652PSIP
Sephutheloana se lumellanang le RoHS

BOHLOKOA TSEBISO qetellong ea leqephe lena la lintlha e bua ka boteng, tiisetso, liphetoho, tšebeliso ea lits'ebetso tsa bohlokoa tsa polokeho, litaba tsa thepa ea mahlale le tse ling tsa boits'oaro ba bohlokoa. TŠEBELETSO EA TSOHLE bakeng sa lihlahisoa tsa tlhahiso ea pele; e ka fetohang ntle le tsebiso.

Lisebelisoa

868 le 902 ho isa ho 928 MHz ISM le litsamaiso tsa SRD 1 tse theohelang ho 4 kHz ea bandwidth ea ho amohela
Moaho oa boiketsetso
- Ho aha lits'ebetso tsa ts'ireletso - sebui sa motsamao, senotlolo se bohlale sa elektroniki, sensor ea lemati le fensetere, sistimi ea mamati a karache, heke
- HVAC - thermostat, sensor ea tikoloho e se nang mohala, molaoli oa sistimi ea HVAC, heke
- Sistimi ea ts'ireletso ea mollo - sesebelisoa sa mosi le mocheso, phanele ea taolo ea mollo (FACP)
- Teko ea video - kh'amera ea marang-rang ea IP
- Li-elevator le li-escalator - sebaka se ka sehloohong sa taolo ea lifti bakeng sa li-elevator le li-escalator

Grid infrastructure
- Limithara tse bohlale - mithara ea metsi, mithara ea khase, mithara ea motlakase, le likabi tsa litšenyehelo tsa mocheso
- Lipuisano tsa Grid - likhokahano tse se nang mohala - lits'ebetso tsa sensor tsa nako e telele
- Lisebelisoa tsa ho tjhaja tsa EV - seteishene sa ho tjhaja AC (qubu).
- Matla a mang a mang - kotulo ea matla
Lipalangoang tsa indasteri - ho latela thepa
Boiketsetso ba feme le taolo

Bongaka
Thepa ea puisano
- Marang-rang a marang-rang - LAN e se nang mohala kapa libaka tsa phihlello tsa Wi-Fi, router ea moeli

Tlhaloso

Sesebelisoa sa SimpleLink ™ CC1312PSIP ke mochini o se nang mohala oa System-in-Package (SiP) Sub-1 GHz o tšehetsang IEEE 802.15.4, IPv6-enabled objects (6LoWPAN), mioty, proprietary systems, ho kenyeletsoa le TI 15.4-Stack. CC1312PSIP microcontroller (MCU) e ipapisitse le processor e kholo ea Arm M4F mme e ntlafalitsoe bakeng sa puisano e se nang mohala e nang le matla a tlase le kutlo e tsoetseng pele ho meaho ea marang-rang, ho aha othomathike, ho iketsetsa mabenkele le lits'ebetso tsa bongaka. CC1312PSIP e na le boroko bo tlaase ba 0.9 μA le RTC le 80KB RAM ho boloka. Ntle le processor ea mantlha ea Cortex® M4F, sesebelisoa se boetse se na le "Sensor Controller" e ikemetseng e tlase haholo e nang le matla a ho tsosa kapele. Joalo ka mohlalaampLe, molaoli oa sensor o khona ho 1-Hz ADC sampling ka karolelano 1-μA tsamaiso ea hona joale.
CC1312PSIP e na le SER e tlase (Lebelo la Phoso e Bonolo) FIT (Ho hloleha ka nako) bakeng sa nako e telele ea ts'ebetso. Ka linako tsohle SRAM parity e fokotsa kotsi ea bobolu ka lebaka la liketsahalo tse ka bang teng tsa mahlaseli. Tumellanong le litlhoko tsa nako ea bophelo ba bareki ba bangata ba lilemo tse 10 ho isa ho tse 15 kapa nako e telele, TI e na le leano la potoloho ea bophelo ba sehlahisoa ka boitlamo ba bophelo bo bolelele ba sehlahisoa le ho tsoela pele ha phepelo ho kenyelletsa le ho fumana likarolo tse peli tsa bohlokoa ho SIP. Sesebelisoa sa CC1312PSIP ke karolo ea sethala sa SimpleLink™ MCU, se nang le Wi-Fi®, Bluetooth® Low Energy, Thread, Zigbee, Wi-SUN®, Amazon Sidewalk, mioty, Sub-1 GHz MCUs, le li-MCU tse amohelang. CC1312PSIP ke karolo ea potefolio e kenyelletsang li-pin-compatible 2.4-GHz SIPs bakeng sa ho feto-fetoha ha bonolo ha sehlahisoa se se nang mohala ho maemo a mangata a puisano. Sesebediswa se tlwaelehileng sa SimpleLink™CC13xx le CC26xx Software Development Kit (SDK) le SysConfig sesebelisoa sa phetolo se tshehetsa ho falla pakeng tsa disebediswa tse potefoliong. Palo e felletseng ea li-software stacks, kopo examples le lithupelo tsa SimpleLink Academy li kenyelelitsoe ho SDK. Ho fumana lintlha tse ling, etela khokahano ea waelese.

KAROLO NUMBER	PHEKO	BOKOLO BA MMELE (NOM)
Setšoantšo sa CC1312PSIPMOT	QFM	7.00 limilimithara × 7.00 limilimithara

(1) Bakeng sa karolo ea morao-rao, sephutheloana, le tlhahisoleseding ea ho odara bakeng sa lisebelisoa tsohle tse fumanehang, bona Package Option Addendum ho Mechanical, Packaging, and Orderable Information, kapa bona TI. websebaka.
1 Sheba RF Core bakeng sa lintlha tse eketsehileng mabapi le litekanyetso tsa protocol tse tšehetsoeng, lifomate tsa modulation, le litefiso tsa data.

Setšoantšo se sebetsang sa Block

Nalane ea Phetoho

HLOKOMELA: Linomoro tsa maqephe bakeng sa litokiso tse fetileng li ka fapana le linomoro tsa maqephe a mofuta oa hajoale.

LETSATSI	PUSELETSO TS'OLO	LINTLHA TSEO
Mots'eanong-23	*	Phatlalatso ea Pele

Sesebediswa Papiso

Pin Configuration le Mesebetsi

7.1 Setšoantšo sa Pin - Pakete ea MOT (Top View)
Setšoantšo sa 7-1. MOT (7-mm × 7-mm) Pinout, 0.5-mm Pitch (Hodimo View)

Lithakhisa tse latelang tsa I/O tse tšoailoeng ho Setšoantšo sa 7-1 ka mongolo o motenya li na le bokhoni ba ho khanna haholo:

Pin 23, DIO_5
Pin 24, DIO_6
Pin 25, DIO_7

Pin 34, JTAG_TMSC
Pin 36, DIO_16
Pin 37, DIO_17

Lithakhisa tse latelang tsa I/O tse tšoailoeng ho Setšoantšo sa 7-1 ka mongolo o tšekaletseng li na le bokhoni ba analog:

Pin 1, DIO_26
Pin 2, DIO_27

Pin 3, DIO_28
Pin 7, DIO_29
Pin 8, DIO_30

Pin 44, DIO_23
Pin 45, DIO_24
Pin 48, DIO_25

7.2 Litlhaloso tsa Lipontšo - Sephutheloana sa MOT
Lethathamo la 7-1. Litlhaloso tsa Letšoao - Sephutheloana sa SIP

PIN		I/O	MOFUTA	TLHALOSO
NAME	NO.	I/O	MOFUTA	TLHALOSO
NC	14	I/O	Dijithale	Ha ho Connect
DIO_1	21	I/O	Dijithale	GPIO
DIO_10	28	I/O	Dijithale	GPIO
DIO_11	29	I/O	Dijithale	GPIO
DIO_12	30	I/O	Dijithale	GPIO
DIO_13	31	I/O	Dijithale	GPIO
DIO_14	32	I/O	Dijithale	GPIO
DIO_15	33	I/O	Dijithale	GPIO
DIO_16	36	I/O	Dijithale	GPIO, JTAG_TDO, bokhoni ba koloi e phahameng
DIO_17	37	I/O	Dijithale	GPIO, JTAG_TDI, bokhoni ba koloi e phahameng
DIO_18	39	I/O	Dijithale	GPIO
DIO_19	40	I/O	Dijithale	GPIO
DIO_2	20	I/O	Dijithale	GPIO
DIO_20	41	I/O	Dijithale	GPIO
DIO_21	42	I/O	Dijithale	GPIO
DIO_22	43	I/O	Dijithale	GPIO
DIO_23	44	I/O	Digital kapa Analog	GPIO, bokhoni ba analog
DIO_24	45	I/O	Digital kapa Analog	GPIO, bokhoni ba analog
DIO_25	48	I/O	Digital kapa Analog	GPIO, bokhoni ba analog
DIO_26	1	I/O	Digital kapa Analog	GPIO, bokhoni ba analog
DIO_27	2	I/O	Digital kapa Analog	GPIO, bokhoni ba analog
DIO_28	3	I/O	Digital kapa Analog	GPIO, bokhoni ba analog
DIO_29	7	I/O	Digital kapa Analog	GPIO, bokhoni ba analog
NC	15	I/O	Dijithale	Ha ho Connect
DIO_30	8	I/O	Digital kapa Analog	GPIO, bokhoni ba analog
PIO_31	38	I/O	Dijithale	E ts'ehetsa ts'ebetso ea peripheral feela. Ha e tšehetse tšebetso e akaretsang ea I/O.
DIO_4	22	I/O	Dijithale	GPIO
DIO_5	23	I/O	Dijithale	GPIO, bokhoni ba ho khanna bo phahameng
DIO_6	24	I/O	Dijithale	GPIO, bokhoni ba ho khanna bo phahameng
DIO_7	25	I/O	Dijithale	GPIO, bokhoni ba ho khanna bo phahameng
DIO_8	26	I/O	Dijithale	GPIO
DIO_9	27	I/O	Dijithale	GPIO
GND	5	—	—	GND
GND	9	—	—	GND
GND	10	—	—	GND
GND	11	—	—	GND
GND	12	—	—	GND
GND	13	—	—	GND
GND	16	—	—	GND
GND	17	—	—	GND
GND	19	—	—	GND
GND	49-73	—	—	GND

7.3 Likhokahanyo bakeng sa Pins le Mejule e sa sebelisoeng
Lethathamo la 7-2. Likhokahano bakeng sa Pins tse sa sebelisoeng

PIN		I/O	MOFUTA	TLHALOSO
NAME	NO.	I/O	MOFUTA	TLHALOSO
NC	6	—	—	Ha ho Connect
NRETSENG	4	I	Dijithale	Seta bocha, sebetsa tlase. Sehanyetsi sa ka hare sa ho hula le 100 nF ho ea ho VDDS_PU
RF	18	—	RF	50 ohm RF boema-kepe
JTAG_TCKC	35	I	Dijithale	JTAG_TCKC
JTAG_TMSC	34	I/O	Dijithale	JTAG_TMSC, bokhoni ba koloi e phahameng
VDDS	46	—	Matla	1.8-V ho 3.8-V phepelo ea mantlha ea SIP
VDDS_PU	47	—	Matla	Matla a ho seta mohanyetsi oa ka hare oa ho hula

Litlhaloso

8.1 Likhakanyo tse Felletseng ka ho Fetisisa
holim'a mefuta e fapaneng ea mocheso oa moea o sa lefelloeng (ntle le haeba ho boletsoe ka tsela e 'ngoe)(1) (2)

			MIN	MAX	THUTO
VDDS(3)	Phepelo voltage		–0.3	4.1	V
	Moqtage ho phini efe kapa efe ea dijithale(4)		–0.3	VDDS + 0.3, max 4.1	V
Vin	Moqtage mabapi le tlhahiso ea ADC	Moqtage scaling e lumelletsoe	–0.3	VDDS	V
		Moqtage scaling ba holofetse, referense ea ka hare	–0.3	1.49
		Moqtage scaling e holofetse, VDDS e le litšupiso	–0.3	VDDS / 2.9
			10		dBm
Tstg	Mocheso oa polokelo		–40	150	°C

Ho sebetsa ka ntle ho Absolute Maximum Ratings ho ka baka tšenyo e sa feleng ea sesebelisoa. Litefiso tse phahameng ka ho fetesisa ha li bolele hore sesebelisoa se sebetsa maemong ana kapa a mang ntle le a thathamisitsoeng tlas'a Maemo a Recommended Operating Conditions. Haeba e sebelisoa ka ntle ho Maemo a Reteletsoeng a Ts'ebetso empa e le ka har'a Absolute Maximum Ratings, sesebelisoa se kanna sa se sebetse ka botlalo, 'me sena se ka ama ts'epahalo ea sesebelisoa, ts'ebetso, ts'ebetso, le ho khutsufatsa bophelo ba sesebelisoa.
Tsohle voltaglitekanyetso tsa e li mabapi le mobu, ntle le ha ho boletsoe ka tsela e 'ngoe.
VDDS_DCDC, VDDS2 le VDDS3 li tlameha ho ba maemong a tšoanang le a VDDS.

Ho kenyelletsa le li-DIO tse nang le bokhoni ba analog.

8.2 Litekanyo tsa ESD

				VALUE	THUTO
VESD	Phallo ea motlakase	Mohlala oa 'mele oa motho (HBM), ho latela ANSI/ESDA/JEDEC JS-001(1)	Lithako tsohle	±1000	V
VESD	Phallo ea motlakase	Mofuta oa sesebelisoa se qositsoeng (CDM), ho latela ANSI/ESDA/JEDEC JS-002(2)	Lithako tsohle	±500	V

Tokomane ea JEDEC JEP155 e bolela hore 500-V HBM e lumella tlhahiso e sireletsehileng ka mokhoa o tloaelehileng oa taolo ea ESD.

Tokomane ea JEDEC JEP157 e bolela hore 250-V CDM e lumella tlhahiso e sireletsehileng ka mokhoa o tloaelehileng oa taolo ea ESD.

8.3 Maemo a Tšebetso a khothalelitsoeng
holim'a mocheso oa mocheso oa moea o sa lefelloeng (ntle le haeba ho boletsoe ka tsela e 'ngoe)

		MIN	MAX	THUTO
Thempereichara ea tikoloho e sebetsang(1) (2)		–40	105	°C
Phepelo e sebetsang voltage (VDDS)		1.8	3.8	V
Phepelo e sebetsang voltage (VDDS), mokhoa oa ho matlafatsa	VDDR = 1.95 V +14 dBm RF e hlahisoang ka tlase ho 1 GHz matla ampmoqhobi	2.1	3.8	V
Phano e ntseng e phahama voltage bolaile sekhahla		0	100	mV/µs
Phapang e oeleng voltage bolaile sekhahla		0	20	mV/µs

(1) Ts'ebetso ea mocheso kapa haufi le mocheso o phahameng oa ts'ebetso bakeng sa nako e telele e tla fella ka phokotso ea bophelo.
(2) Bakeng sa litšobotsi tsa ho hanyetsa mocheso li bua ka.
8.4 Phepelo ea Matla le Limojule
holim'a mocheso oa mocheso oa moea o sa lefelloeng (ntle le haeba ho boletsoe ka tsela e 'ngoe)

PARAMETER		MIN	TYP	MAX	THUTO
Matla a ho-Reset (POR) a VDDS		1.1 - 1.55			V
VDDS Brown-out Detector (BOD) (1)	Moepo o ntseng o phahama	1.77			V
VDDS Brown-out Detector (BOD), pele ho boot ea pele (2)	Moepo o ntseng o phahama	1.70			V
VDDS Brown-out Detector (BOD) (1)	Ho oela moeling	1.75			V

(1) Bakeng sa boost mode (VDDR = 1.95 V), ho qalisoa ha software ea bakhanni ba TI ho tla fokotsa meeli ea VDDS BOD ho ea holimo (hoo e ka bang 2.0 V)
2
8.5 Tšebeliso ea Matla - Mekhoa ea Matla
Ha e lekantsoe ka moralo oa litšupiso oa CC1312PSIP-EM ka Tc = 25 °C, VDDS = 3.6 V e nang le DC / DC e nolofalitsoeng ntle le haeba ho boletsoe ka tsela e 'ngoe.

PARAMETER		LITEKO MAEMO	TYP	THUTO
Tšebeliso ea Hona Joale
Icore	Seta bocha	Seta bocha. RESET_N phini e tiisitsoe kapa VDDS e ka tlase ho moeli oa matla a ho seta bocha (4)	36	µA
	Koala	Koala. Ha ho lioache tse ntseng li sebetsa, ha ho nako e bolokiloeng	150	nA
	E eme ka ho boloka cache	RTC e sebetsa, CPU, 80KB RAM le (karolo) ea ho boloka rejisetara. RCOSC_LF	0.9	µA
	E eme ka ho boloka cache	RTC e sebetsa, CPU, 80KB RAM le (karolo) ea ho boloka rejisetara XOSC_LF	1.0	µA
	E eme ka ho boloka cache	RTC e sebetsa, CPU, 80KB RAM le (karolo) ea ho boloka rejisetara XOSC_LF	2.8	µA
	E eme ka ho boloka cache	RTC e sebetsa, CPU, 80KB RAM le (karolo) ea ho boloka rejisetara XOSC_LF	2.9	µA
	Qetello	Supply Systems le RAM e tsamaisoang ke RCOSC_HF	590	µA
Icore	E sebetsa	MCU e mathang CoreMark ho 48 MHz RCOSC_HF	2.89	mA
Pheripheral Current Tšebeliso
Iperi	Peripheral power domain	Delta ea hajoale e nang le domain name e lumelletsoe	82	µA
	Sebaka sa matla sa serial	Delta ea hajoale e nang le domain name e lumelletsoe	5.5
	RF Core	Delta ea hajoale e nang le sebaka sa matla se lumelletsoeng, oache e nolofalitsoe, RF ea mantlha e sa sebetse	179
	µDMA	Delta ea hajoale e nang le oache e lumelletsoeng, module ha e sebetse	54
	Lisebelisoa tsa nako	Delta ea hona joale e nang le oache e lumelletsoeng, mojule ha e sebetse(3)	68
	I2C	Delta ea hajoale e nang le oache e lumelletsoeng, module ha e sebetse	8.2
	I2S	Delta ea hajoale e nang le oache e lumelletsoeng, module ha e sebetse	22
	SSI	Delta ea hona joale e nang le oache e lumelletsoeng, mojule ha e sebetse(2)	70
	UART	Delta ea hona joale e nang le oache e lumelletsoeng, mojule ha e sebetse(1)	141
	CRYPTO (AES)	Delta ea hajoale e nang le oache e lumelletsoeng, module ha e sebetse	21
	PKA	Delta ea hajoale e nang le oache e lumelletsoeng, module ha e sebetse	71
	TRNG	Delta ea hajoale e nang le oache e lumelletsoeng, module ha e sebetse	30
Tšebeliso ea Enjene ea Sensor Controller
ISCE	Mokhoa o sebetsang	24 MHz, lupu e sa feleng	808	µA
ISCE	Mokhoa o tlase oa matla	2 MHz, lupu e sa feleng	30.1	µA

UART e le 'ngoe feela e mathang
Ke SSI e le 'ngoe feela e sebetsang

Ke GPTimer e le 'ngoe feela e sebetsang
CC1312PSIP e kopanya 100 kΩ hula-up resistor ho nRESET

8.6 Tšebeliso ea Matla - Mekhoa ea Radio
Ha e lekantsoe ka moralo oa litšupiso oa CC1312PSIP-EM ka Tc = 25 °C, VDDS = 3.6 V e nang le DC / DC e nolofalitsoeng ntle le haeba ho boletsoe ka tsela e 'ngoe.
Ho sebelisa boost mode (ho eketsa VDDR ho fihlela ho 1.95 V), ho tla eketsa tsamaiso ea hona joale ka 15% (ha e sebetse ho TX +14 dBm setting moo hona joale hona joale e seng e kenyelelitsoe).
Maqhubu a Icore le a Iperi a kenyellelitsoeng linomorong tse ka tlase.

PARAMETER		LITEKO MAEMO	TYP	THUTO
	Radio e amohela hona joale, 868 MHz		5.8	mA
	Radio fetisa hona joale Regular PA	0 dBm tlhahiso ea matla a ho beha 868 MHz	9.4	mA
	Radio fetisa hona joale Regular PA	+10 dBm tlhahiso ea matla a ho beha 868 MHz	17.3	mA
	Radio fetisa mokhoa oa hona joale oa Boost, PA e tloaelehileng	+14 dBm tlhahiso ea matla a ho beha 868 MHz	28.7	mA

8.7 Litšobotsi tsa mohopolo tse sa fetoheng (Flash).
Ka holim'a mocheso oa mocheso oa moea o sa lefelloeng le VDDS = 3.0 V (ntle le haeba ho boletsoe ka tsela e 'ngoe)

PARAMETER	LITEKO MAEMO	MIN	TYP	MAX	THUTO
Boholo ba lekala la Flash		8			KB
Lipotoloho tse tšehetsoeng ke flash pele li hloleha, banka e le 'ngoe(1) (5)		30			k Lipotoloho
Lipotoloho tse tšehetsoeng ke flash pele li hloleha, lekala le le leng(2)		60			k Lipotoloho
Bongata ba palo ea mesebetsi ea ho ngola ka mola pele ho hlakoloa (3)		83			Ngola Ts'ebetso
Ho boloka lebone	105 °C	11.4			Lilemo tse 105°C
Flash sector e hlakola hajoale	Karolelano ea delta current	10.7			mA
Nako ea ho hlakola karolo ea Flash(4)	Lipotoloho tse zero	10			ms
Nako ea ho hlakola karolo ea Flash(4)	30k potoloho	4000			ms
Flash ngola hajoale	Karolelano ea delta current, li-byte tse 4 ka nako	6.2			mA
Nako ea ho ngola ea Flash(4)	Li-byte tse 4 ka nako	21.6			µs

Phallo e felletseng ea banka e baloa e le potoloho e le 'ngoe ea ho hlakola lekaleng ka leng.
Ho fihla ho likarolo tse 4 tse khethiloeng ke bareki li ka hlakoloa ka bonngoe makhetlo a 30k ho feta moeli oa banka oa li-cycle 30k.

Mohala o mong le o mong oa mantsoe ke li-bits tse 2048 (kapa 256 byte) ka bophara. Moedi ona o tsamaellana le mengolo e latellanang ea memori ea li-byte tse 4 (3.1) bonyane ka mongolo o mong le o mong holim'a mola oa mantsoe. Haeba ho hlokahala mangolo a eketsehileng ho lentsoe le tšoanang, ho hlokahala ho hlakola karolo hang ha palo e kholo ea ho ngola ka mola e fihletsoe.
Nomoro ena e ipapisitse le botsofali ba Flash mme e eketseha ha nako e ntse e tsamaea le ho hlakola lipotoloho
Ho tlosa flash nakong ea ho hlakola kapa mekhoa ea lenaneo ha se ts'ebetso e sireletsehileng.

8.8 Litšobotsi tsa ho hanyetsa Thermal Resistance

MPHETE METRI		PHEKO	THUTO
		MOT (SIP)
		73 LIPHIRI
RθJA	Junction-to-ambient ho hanyetsa mocheso	48.7	°C/W(1)
RθJC(holimo)	Khohlano-to-case (ka holimo) ho hanyetsa mocheso	12.4	°C/W(1)
RθJB	Junction-to-board thermal resistance	32.2	°C/W(1)
ψJT	Tekanyetso ea sebopeho sa Junction-to-top	0.40	°C/W(1)
ψJB	Tekanyetso ea sebopeho sa Junction-to-board	32.0	°C/W(1)

(1) °C/W = likhato tsa Celsius ka watt.
8.9 RF Frequency Bands
Ho feta moo mocheso o sebetsang oa moea o sa lefelloeng (ntle le haeba ho boletsoe ka tsela e 'ngoe).

PARAMETER	MIN	TYP	MAX	THUTO
Sehlopha sa maqhubu	863		930	MHz

8.10 861 MHz ho isa ho 1054 MHz – Amohela (RX)
Ha e lekantsoe ka CC1312PSIP-EM moralo oa litšupiso o nang le Tc = 25 °C, VDDS = 3.0 V e nang le DC / DC e nolofalitsoeng le PA e matla e amanang le VDDS ntle le haeba ho boletsoe ka tsela e 'ngoe.
Litekanyo tsohle li etsoa ka mokhoa oa ho kenya antenna ka tsela e kopantsoeng ea RX le TX, ntle le matla a phahameng a PA a lekantsoeng ka khokahanyo ea antenna e inehetseng. Litekanyo tsohle lia etsoa.

PARAMETER	LITEKO MAEMO	MIN	TYP	MAX	THUTO
Kakaretso Parameters
Digital channel filterable programmable fumana bandwidth		4		4000	kHz
Boholo ba mohato oa sekhahla sa data		1.5		bps
Likhase tsa spurious 25 MHz ho 1 GHz	868 MHz E hlahisoang ke mesi e lekantsoeng ho latela ETSI EN 300 220	<-57		dBm
Likhase tsa spurious 1 GHz ho isa ho 13 GHz		<-47		dBm
802.15.4, 50 kbps, ±25 kHz fapoha, 2-GFSK, 100 kHz RX Bandwidth
Kutloelo-bohloko	BER = 10–2, 868 MHz	–108		dBm
Moeli oa ho tlala	BER = 10–2, 868 MHz	10		dBm
Khetho, ± 200 kHz	BER = 10–2, 868 MHz(1)	44		dB
Khetho, ± 400 kHz	BER = 10–2, 868 MHz(1)	48		dB
Ho thibela, ± 1 MHz	BER = 10–2, 868 MHz(1)	57		dB
Ho thibela, ± 2 MHz	BER = 10–2, 868 MHz(1)	62		dB
Ho thibela, ± 5 MHz	BER = 10–2, 868 MHz(1)	68		dB
Ho thibela, ± 10 MHz	BER = 10–2, 868 MHz(1)	76		dB
Ho hana setšoantšo (matšeliso a setšoantšo a lumelletsoe)	BER = 10–2, 868 MHz(1)	39		dB
RSSI dynamic range	Ho qala ho tloha moeling oa kutloisiso	95		dB
Ho nepahala ha RSSI	Ho qala ho tloha moeling oa kutloisiso ho pholletsa le mefuta e fanoeng ea matla	±3		dB
802.15.4, 100 kbps, ±25 kHz fapoha, 2-GFSK, 137 kHz RX Bandwidth
Sensitivity 100 kbps	868 MHz, 1% PER, 127 byte payload	-101		dBm
Khetho, ± 200 kHz	868 MHz, 1% PER, 127 byte payload. Ho batloa lets'oao ho -96 dBm	38		dB
Khetho, ± 400 kHz	868 MHz, 1% PER, 127 byte payload. Ho batloa lets'oao ho -96 dBm	45		dB
Co ho lahla	868 MHz, 1% PER, 127 byte payload. Ho batloa lets'oao ho -79 dBm	-9		dB
802.15.4, 200 kbps, ±50 kHz fapoha, 2-GFSK, 311 kHz RX Bandwidth
Kutloelo-bohloko	BER = 10–2, 868 MHz	–103		dBm
Kutloelo-bohloko	BER = 10–2, 915 MHz	–103		dBm
Khetho, ± 400 kHz	BER = 10–2, 915 MHz. Ho batloa lets'oao la 3 dB kaholimo ho moeli oa kutlo.	41		dB
Khetho, ± 800 kHz	BER = 10–2, 915 MHz. Ho batloa lets'oao la 3 dB kaholimo ho moeli oa kutlo.	47		dB
Ho thibela, ± 2 MHz	BER = 10–2, 915 MHz. Ho batloa lets'oao la 3 dB kaholimo ho moeli oa kutlo.	55		dB
Ho thibela, ± 10 MHz	BER = 10–2, 915 MHz. Ho batloa lets'oao la 3 dB kaholimo ho moeli oa kutlo.	67		dB
802.15.4, 500 kbps, ±190 kHz fapoha, 2-GFSK, 655 kHz RX Bandwidth
Sensitivity 500 kbps	916 MHz, 1% PER, 127 byte payload	-90		dBm
Khetho, ± 1 MHz	916 MHz, 1% PER, 127 byte payload. Ho batloa lets'oao ho -88 dBm	11		dB
Khetho, ± 2 MHz	916 MHz, 1% PER, 127 byte payload. Ho batloa lets'oao ho -88 dBm	43		dB
Co ho lahla	916 MHz, 1% PER, 127 byte payload. Ho batloa lets'oao ho -71 dBm	-9		dB
SimpleLink™ Long Range 2.5 kbps or 5 kbps (20 ksym/s, 2-GFSK, ±5 kHz Deviation, FEC (Half Rate), DSSS = 1:2 kapa 1:4, 34 kHz RX Bandwidth
Kutloelo-bohloko	2.5 kbps, BER = 10–2, 868 MHz	-119		dBm
Kutloelo-bohloko	5 kbps, BER = 10–2, 868 MHz	-117		dBm
Moeli oa ho tlala	2.5 kbps, BER = 10–2, 868 MHz	10		dBm
Khetho, ± 100 kHz	2.5 kbps, BER = 10–2, 868 MHz(1)	49		dB
Khetho, ± 200 kHz	2.5 kbps, BER = 10–2, 868 MHz(1)	50		dB
Khetho, ± 300 kHz	2.5 kbps, BER = 10–2, 868 MHz(1)	51		dB
Ho thibela, ± 1 MHz	2.5 kbps, BER = 10–2, 868 MHz(1)	63		dB
Ho thibela, ± 2 MHz	2.5 kbps, BER = 10–2, 868 MHz(1)	68		dB
Ho thibela, ± 5 MHz	2.5 kbps, BER = 10–2, 868 MHz(1)	78		dB
Ho thibela, ± 10 MHz	2.5 kbps, BER = 10–2, 868 MHz(1)	87		dB

Ha e lekantsoe ka CC1312PSIP-EM moralo oa litšupiso o nang le Tc = 25 °C, VDDS = 3.0 V e nang le DC / DC e nolofalitsoeng le PA e matla e amanang le VDDS ntle le haeba ho boletsoe ka tsela e 'ngoe.
Litekanyo tsohle li etsoa ka mokhoa oa ho kenya antenna ka tsela e kopantsoeng ea RX le TX, ntle le matla a phahameng a PA a lekantsoeng ka khokahanyo ea antenna e inehetseng. Litekanyo tsohle lia etsoa.

PARAMETER	LITEKO MAEMO	MIN TYP MAX	THUTO
Ho hana setšoantšo (matšeliso a setšoantšo a lumelletsoe)	2.5 kbps, BER = 10–2, 868 MHz(1)	45	dB
RSSI dynamic range	Ho qala ho tloha moeling oa kutloisiso	97	dB
Ho nepahala ha RSSI	Ho qala ho tloha moeling oa kutloisiso ho pholletsa le mefuta e fanoeng ea matla	±3	dB
Wireless M-Bus
Kutlo ea seamoheli, wM-BUS C-mode, 100 kbps ±45 kHz	Bandwidth ea Moamoheli 236 kHz, BER 1%	-104	dBm
Kutlo ea seamoheli, wM-BUS T-mode, 100 kbps ±50 kHz	Bandwidth ea Moamoheli 236 kHz, BER 1%	-103	dBm
Kutloisiso ea moamoheli, wM-BUS S2-mode, 32.768 kbps ±50 kHz	Bandwidth ea Moamoheli 196 kHz, BER 1%	-109	dBm
Kutloisiso ea moamoheli, wM-BUS S1-mode, 32.768 kbps ±50 kHz	Bandwidth ea Moamoheli 311 kHz, BER 1%	-107	dBm
OK, 4.8 kbps, 39 kHz RX Bandwidth
Kutloelo-bohloko	BER = 10–2, 868 MHz	-112	dBm
Kutloelo-bohloko	BER = 10–2, 915 MHz	-112	dBm
Narrowband, 9.6 kbps ±2.4 kHz e fapoha, 2-GFSK, 868 MHz, 17.1 kHz RX Bandwidth
Kutloelo-bohloko	1% BER	-118	dBm
Haufi le Channel e Hanoang	1% BER. Ho batloa lets'oao la 3 dB ka holim'a moeli oa kutloisiso ea referense ea ETSI (-104.6 dBm). Sekena-lipakeng ± 20 kHz	39	dB
Ho Hanoa ha Channel e 'Ngoe	1% BER. Ho batloa lets'oao la 3 dB ka holim'a moeli oa kutloisiso ea referense ea ETSI (-104.6 dBm). Sekena-lipakeng ± 40 kHz	40	dB
Ho thibela, ± 1 MHz	1% BER. Ho batloa lets'oao la 3 dB kaholimo ho moeli oa kutlo oa ETSI (-104.6 dBm).	65	dB
Ho thibela, ± 2 MHz		69	dB
Ho thibela, ± 10 MHz		85	dB
1 Mbps, ±350 kHz fapoha, 2-GFSK, 2.2 MHz RX Bandwidth
Kutloelo-bohloko	BER = 10–2, 868 MHz	-94	dBm
Kutloelo-bohloko	BER = 10–2, 915 MHz	-93	dBm
Ho thibela, +2 MHz	BER = 10–2, 915 MHz. Ho batloa lets'oao la 3 dB kaholimo ho moeli oa kutlo.	44	dB
Ho thibela, -2 MHz	BER = 10–2, 915 MHz. Ho batloa lets'oao la 3 dB kaholimo ho moeli oa kutlo.	27	dB
Ho thibela, +10 MHz	BER = 10–2, 915 MHz. Ho batloa lets'oao la 3 dB kaholimo ho moeli oa kutlo.	59	dB
Ho thibela, -10 MHz	BER = 10–2, 915 MHz. Ho batloa lets'oao la 3 dB kaholimo ho moeli oa kutlo.	54	dB
Wi-SUN, 2-GFSK
Kutloelo-bohloko	50 kbps, ±12.5 kHz fapoha, 2-GFSK, 866.6 MHz, 68 kHz RX BW, 10% PER, 250 byte payload	-104	dBm
Khetho, -100 kHz, 50 kbps, ±12.5 kHz e kheloha, 2-GFSK, 866.6 MHz	50 kbps, ±12.5 kHz e kheloha, 2-GFSK, 68 kHz RX Bandwidth, 866.6 MHz, 10% PER, 250 byte payload. Ho batloa lets'oao la 3 dB kaholimo ho boemo ba kutlo	32	dB
Khetho, +100 kHz, 50 kbps, ±12.5 kHz e kheloha, 2-GFSK, 866.6 MHz		33	dB
Khetho, ±100 kHz, 50 kbps, ±12.5 kHz e kheloha, 2-GFSK, 866.6 MHz		30	dB
Khetho, -200 kHz, 50 kbps, ±12.5 kHz e kheloha, 2-GFSK, 866.6 MHz		36	dB
Khetho, +200 kHz, 50 kbps, ±12.5 kHz e kheloha, 2-GFSK, 866.6 MHz		38	dB
Khetho, ±200 kHz, 50 kbps, ±12.5 kHz e kheloha, 2-GFSK, 866.6 MHz		37	dB
Kutloelo-bohloko	50 kbps, ±25 kHz fapoha, 2-GFSK, 98 kHz RX Bandwidth,918.2 MHz, 10% PER, 250 byte payload	-104	dBm

Ha e lekantsoe ka CC1312PSIP-EM moralo oa litšupiso o nang le Tc = 25 °C, VDDS = 3.0 V e nang le DC / DC e nolofalitsoeng le PA e matla e amanang le VDDS ntle le haeba ho boletsoe ka tsela e 'ngoe. Litekanyo tsohle li etsoa ka mokhoa oa ho kenya antenna ka tsela e kopantsoeng ea RX le TX, ntle le matla a phahameng a PA a lekantsoeng ka khokahanyo ea antenna e inehetseng. Litekanyo tsohle lia etsoa.

PARAMETER	LITEKO MAEMO	MIN TYP MAX	THUTO
Khetho, -200 kHz, 50 kbps, ±25 kHz e kheloha, 2-GFSK, 918.2 MHz	50 kbps, ±25 kHz e kheloha, 2-GFSK, 98 kHz RX Bandwidth, 918.2 MHz, 10% PER, 250 byte payload. Ho batloa lets'oao la 3 dB kaholimo ho boemo ba kutlo	34	dB
Khetho, +200 kHz, 50 kbps, ±25 kHz e kheloha, 2-GFSK, 918.2 MHz		35	dB
Khetho, ±200 kHz, 50 kbps, ±25 kHz e kheloha, 2-GFSK, 918.2 MHz		34	dB
Khetho, -400 kHz, 50 kbps, ±25 kHz e kheloha, 2-GFSK, 918.2 MHz		40	dB
Khetho, +400 kHz, 50 kbps, ±25 kHz e kheloha, 2-GFSK, 918.2 MHz		40	dB
Khetho, ±400 kHz, 50 kbps, ±25 kHz e kheloha, 2-GFSK, 918.2 MHz		40	dB
Kutloelo-bohloko	100 kbps, ±25 kHz e kheloha, 2-GFSK, 866.6 MHz, 135 kHz RX BW, 10% PER, 250 byte payload	-102	dBm
Kutloelo-bohloko	100 kbps, ±25 kHz e kheloha, 2-GFSK, 918.2 MHz, 135 kHz RX BW, 10% PER, 250 byte payload	-101	dBm
Khetho, -200 kHz, 100 kbps, ±25 kHz e kheloha, 2-GFSK, 866.6 MHz	100 kbps, ±25 kHz e kheloha, 2-GFSK, 135 kHz RX Bandwidth, 866.6 MHz, 10% PER, 250 byte payload. Ho batloa lets'oao la 3 dB kaholimo ho boemo ba kutlo	37	dB
Khetho, +200 kHz, 100 kbps, ±25 kHz e kheloha, 2-GFSK, 866.6 MHz		38	dB
Khetho, ±200 kHz, 100 kbps, ±25 kHz e kheloha, 2-GFSK, 866.6 MHz		37	dB
Khetho, -400 kHz, 100 kbps, ±25 kHz e kheloha, 2-GFSK, 866.6 MHz		45	dB
Khetho, +400 kHz, 100 kbps, ±25 kHz e kheloha, 2-GFSK, 866.6 MHz		45	dB
Khetho, ±400 kHz, 100 kbps, ±25 kHz e kheloha, 2-GFSK, 866.6 MHz		45	dB
Kutloelo-bohloko	100 kbps, ±50 kHz e kheloha, 2-GFSK, 920.9 MHz, 196 kHz RX BW, 10% PER, 250 byte payload	-100	dBm
Khetho, -400 kHz, 100 kbps, ±50 kHz e kheloha, 2-GFSK, 920.9 MHz	100 kbps, ±50 kHz e kheloha, 2-GFSK, 196 kHz RX Bandwidth, 920.9 MHz, 10% PER, 250 byte payload. Ho batloa lets'oao la 3 dB kaholimo ho boemo ba kutlo	40	dB
Khetho, +400 kHz, 100 kbps, ±50 kHz e kheloha, 2-GFSK, 920.9 MHz		40	dB
Khetho, ±400 kHz, 100 kbps, ±50 kHz e kheloha, 2-GFSK, 920.9 MHz		40	dB
Khetho, -800 kHz, 100 kbps, ±50 kHz e kheloha, 2-GFSK, 920.9 MHz		46	dB
Khetho, +800 kHz, 100 kbps, ±50 kHz e kheloha, 2-GFSK, 920.9 MHz		52	dB
Khetho, ±800 kHz, 100 kbps, ±50 kHz e kheloha, 2-GFSK, 920.9 MHz		48	dB
Kutloelo-bohloko	150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 918.4 MHz, 273 kHz RX BW, 10% PER, 250 byte payload	-96	dBm
Khetho, -400 kHz, 150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 918.4 MHz	150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 273 kHz RX Bandwidth, 918.4 MHz, 10% PER, 250 byte payload. Ho batloa lets'oao la 3 dB kaholimo ho boemo ba kutlo	41	dB
Khetho, +400 kHz, 150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 918.4 MHz		42	dB
Khetho, -800 kHz, 150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 918.4 MHz		46	dB
Khetho, +800 kHz, 150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 918.4 MHz		49	dB
Kutloelo-bohloko		-96	dBm

PARAMETER	LITEKO MAEMO	MIN TYP MAX	THUTO
Khetho, -400 kHz, 150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 920.9 MHz	150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 273 kHz RX Bandwidth, 920.9 MHz, 10% PER, 250 byte payload. Ho batloa lets'oao la 3 dB kaholimo ho boemo ba kutlo	40	dB
Khetho, +400 kHz, 150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 920.9 MHz		42	dB
Khetho, ±400 kHz, 150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 920.9 MHz		40	dB
Khetho, -800 kHz, 150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 920.9 MHz		46	dB
Khetho, +800 kHz, 150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 920.9 MHz		49	dB
Khetho, ±800 kHz, 150 kbps, ±37.5 kHz e kheloha, 2-GFSK, 920.9 MHz		46	dB
Kutloelo-bohloko	200 kbps, ±50 kHz e kheloha, 2-GFSK, 918.4 MHz, 273 kHz RX BW, 10% PER, 250 byte payload	-97	dBm
Khetho, -400 kHz, 200 kbps, ±50 kHz e kheloha, 2-GFSK, 918.4 MHz	200 kbps, ± 50 kHz e kheloha, 2-GFSK, 273 kHz RX Bandwidth, 918.4 MHz, 10% PER, 250 byte payload. Ho batloa lets'oao la 3 dB kaholimo ho boemo ba kutlo	40	dB
Khetho, +400 kHz, 200 kbps, ±50 kHz e kheloha, 2-GFSK, 918.4 MHz		43	dB
Khetho, ±400 kHz, 200 kbps, ±50 kHz e kheloha, 2-GFSK, 918.4 MHz		41	dB
Khetho, -800 kHz, 200 kbps, ±50 kHz e kheloha, 2-GFSK, 918.4 MHz		46	dB
Khetho, +800 kHz, 200 kbps, ±50 kHz e kheloha, 2-GFSK, 918.4 MHz		50	dB
Khetho, ±800 kHz, 200 kbps, ±50 kHz e kheloha, 2-GFSK, 918.4 MHz		48	dB
Kutloelo-bohloko	200 kbps, ±100 kHz e kheloha, 2-GFSK, 920.8 MHz, 273 kHz RX BW, 10% PER, 250 byte payload	-96	dBm
Khetho, -600 kHz, 200 kbps, ±100 kHz e kheloha, 2-GFSK, 920.8 MHz	200 kbps, ±100 kHz e kheloha, 2-GFSK, 273 kHz RX Bandwidth, 920.8 MHz,, 10% PER, 250 byte payload. Ho batloa lets'oao la 3 dB kaholimo ho boemo ba kutlo	43	dB
Khetho, +600 kHz, 200 kbps, ±100 kHz e kheloha, 2-GFSK, 920.8 MHz		47	dB
Khetho, ±600 kHz, 200 kbps, ±100 kHz e kheloha, 2-GFSK, 920.8 MHz		44	dB
Khetho, -1200 kHz, 200 kbps, ±100 kHz e kheloha, 2-GFSK, 920.8 MHz		51	dB
Khetho, +1200 kHz, 200 kbps, ±100 kHz e kheloha, 2-GFSK, 920.8 MHz		54	dB
Khetho, ±1200 kHz, 200 kbps, ±100 kHz e kheloha, 2-GFSK, 920.8 MHz		51	dB
Kutloelo-bohloko	300 kbps, ±75 kHz e kheloha, 2-GFSK, 917.6 MHz, 576 kHz RX BW, 10% PER, 250 byte payload	-94	dBm
Khetho, -600 kHz, 300 kbps, ±75 kHz e kheloha, 2-GFSK, 917.6 MHz	300 kbps, ± 75 kHz e kheloha, 2-GFSK, 576 kHz RX Bandwidth, 917.6 MHz,, 10% PER, 250 byte payload. Ho batloa lets'oao la 3 dB kaholimo ho boemo ba kutlo	27	dB
Khetho, +600 kHz, 300 kbps, ±75 kHz e kheloha, 2-GFSK, 917.6 MHz		45	dB
Khetho, ±600 kHz, 300 kbps, ±75 kHz e kheloha, 2-GFSK, 917.6 MHz		35	dB
Khetho, -1200 kHz, 300 kbps, ±75 kHz e kheloha, 2-GFSK, 917.6 MHz		46	dB
Khetho, +1200 kHz, 300 kbps, ±75 kHz e kheloha, 2-GFSK, 920.8 MHz		50	dB
Khetho, ±1200 kHz, 300 kbps, ±75 kHz e kheloha, 2-GFSK, 917.6 MHz		48	dB
WB-DSSS, 240/120/60/30 kbps (480 ksym/s, 2-GFSK, ±195 kHz Phapang, FEC (Half Rate), DSSS = 1/2/4/8, 622 kHz RX BW)
Kutloelo-bohloko	240 kbps, DSSS = 1, BER = 10–2, 915 MHz	-101	dBm
Kutloelo-bohloko	120 kbps, DSSS = 2, BER = 10–2, 915 MHz	-103	dBm

PARAMETER	LITEKO MAEMO	MIN TYP MAX	THUTO
Kutloelo-bohloko	60 kbps, DSSS = 4, BER = 10–2, 915 MHz	-105	dBm
Kutloelo-bohloko	30 kbps, DSSS = 8, BER = 10–2, 915 MHz	-106	dBm
Ho thibela ± 1 MHz	240 kbps, DSSS = 1, BER = 10–2, 915 MHz	49	dB
Ho thibela ± 2 MHz	240 kbps, DSSS = 1, BER = 10–2, 915 MHz	53	dB
Ho thibela ± 5 MHz	240 kbps, DSSS = 1, BER = 10–2, 915 MHz	58	dB
Ho thibela ± 10 MHz	240 kbps, DSSS = 1, BER = 10–2, 915 MHz	67	dB

(1) Letšoao le batloang 3 dB ka holimo ho moeli oa kutloisiso ea boitsebiso ho latela ETSI EN 300 220 v. 3.1.1

8.11 861 MHz ho isa ho 1054 MHz – Fetisa (TX)
E lekanyelitsoe ho moralo oa litšupiso oa CC1312PSIP-EM o nang le Tc = 25 °C, VDDS = 3.0 V e nang le DC/DC e nolofalitsoeng le PA e matla e kopantsoeng le VDDS e sebelisang 2-GFSK, 50 kbps, ± 25 kHz ho kheloha ntle le haeba ho boletsoe ka tsela e 'ngoe. Litekanyo tsohle li etsoa ka mokhoa oa ho kenya antenna ka tsela e kopantsoeng ea RX le TX, ntle le matla a phahameng a PA a lekantsoeng ka khokahanyo ea antenna e inehetseng. Litekanyo tsohle lia etsoa. (1)c

PARAMETER		LITEKO MAEMO	MIN	TYP	MAX	THUTO
Mekhahlelo e akaretsang
Matla a phahameng a tsoang, mokhoa oa boost PA khafetsa		VDDR = 1.95 V Bonyane ba phepelo ea matlatage (VDDS) bakeng sa mokhoa oa ho matlafatsa ke 2.1 V 915 MHz	14			dBm
Matla a phahameng a tsoang, PA kamehla		868 MHz le 915 MHz	12.4			dBm
Sehlahisoa sa motlakase se ka sebelisoang Regular PA		868 MHz le 915 MHz	34			dB
Phapang ea matla a hlahisoang holim'a mocheso oa kamehla PA		+10 dBm setting Ka holim'a sebaka se sebetsang sa mocheso se khothalelitsoeng	±2			dB
Phapang ea matla a hlahisoang holim'a mocheso oa Boost mode, PA e tloaelehileng		+14 dBm setting Ka holim'a sebaka se sebetsang sa mocheso se khothalelitsoeng	±1.5			dB
Likhahla tse fosahetseng le li-harmonics
Mesi e litšila (ntle le li-harmonics) khafetsa PA (2)	30 MHz ho 1 GHz	+14 dBm beha lihlopha tse thibetsoeng tsa ETSI	<-54			dBm
		+14 dBm e beha ETSI kantle ho lihlopha tse thibetsoeng	<-36			dBm
	1 GHz ho isa ho 12.75 GHz (ka ntle ho lihlopha tse thibetsoeng tsa ETSI)	+14 dBm setting e lekantsoeng ho 1 MHz bandwidth (ETSI)		<-30	-35	dBm
Likhase tsa spurious out-of-band Regular PA, 915 MHz (2)	30 MHz ho isa ho 88 MHz (ka har'a lihlopha tse thibetsoeng tsa FCC)	+14 dBm tlhophiso	<-56			dBm
	88 MHz ho isa ho 216 MHz (ka har'a lihlopha tse thibetsoeng tsa FCC)	+14 dBm tlhophiso	<-52			dBm
	216 MHz ho isa ho 960 MHz (ka har'a lihlopha tse thibetsoeng tsa FCC)	+14 dBm tlhophiso	<-50			dBm
	960 MHz ho isa ho 2390 MHz le ka holimo ho 2483.5 MHz (ka har'a sehlopha se thibetsoeng sa FCC)	+14 dBm tlhophiso	<-42			dBm
	1 GHz ho isa ho 12.75 GHz (ka ntle ho lihlopha tse thibetsoeng tsa FCC)	+14 dBm tlhophiso		<-40	-44	dBm
Likhase tsa spurious out- of-band Regular PA, 920.6/928 MHz (2)	Ka tlase ho 710 MHz (ARIB T-108)	+14 dBm tlhophiso	<-36			dBm
	710 MHz ho isa ho 900 MHz (ARIB T-108)	+14 dBm tlhophiso	<-55			dBm
	900 MHz ho isa ho 915 MHz (ARIB T-108)	+14 dBm tlhophiso	<-55			dBm
	930 MHz ho isa ho 1000 MHz (ARIB T-108)	+14 dBm tlhophiso	<-55			dBm
	1000 MHz ho isa ho 1215 MHz (ARIB T-108)	+14 dBm tlhophiso	<-45			dBm
	Ka holimo ho 1215 MHz (ARIB T-108)	+14 dBm tlhophiso	<-30			dBm
Harmonics Kamehla PA	Haronic ea bobeli	+14 dBm setting, 868 MHz	<-30			dBm
		+14 dBm setting, 915 MHz	<-30
	Haronic ea boraro	+14 dBm setting, 868 MHz	<-30			dBm
		+14 dBm setting, 915 MHz	<-42
	Haronic ea bone	+14 dBm setting, 868 MHz	<-30			dBm
		+14 dBm setting, 915 MHz	<-30
	Haronic ea bohlano	+14 dBm setting, 868 MHz	<-30			dBm
		+14 dBm setting, 915 MHz	<-42

E lekanyelitsoe ho moralo oa litšupiso oa CC1312PSIP-EM o nang le Tc = 25 °C, VDDS = 3.0 V e nang le DC/DC e nolofalitsoeng le PA e matla e kopantsoeng le VDDS e sebelisang 2-GFSK, 50 kbps, ± 25 kHz ho kheloha ntle le haeba ho boletsoe ka tsela e 'ngoe. Litekanyo tsohle li etsoa ka mokhoa oa ho kenya antenna ka tsela e kopantsoeng ea RX le TX, ntle le matla a phahameng a PA a lekantsoeng ka khokahanyo ea antenna e inehetseng. Litekanyo tsohle lia etsoa.(1)

PARAMETER		LITEKO MAEMO	MIN TYP MAX	THUTO
Matla a Channel a Haufi
Matla a seteishene se haufi, 14 dBm PA e tloaelehileng	Channel e haufi, 20 kHz offset. 9.6 kbps, h=0.5	12.5 dBm boemo. 868.3 MHz. 14 kHz kanale BW	-24	dBm
Matla a mang a mocha, a tloaelehileng a 14 dBm PA	Tsela e 'ngoe, 40 kHz offset. 9.6 kbps, h=0.5	12.5 dBm boemo. 868.3 MHz. 14 kHz kanale BW	-31	dBm

(1) Mefuta e meng ea maqhubu, sekhahla sa data le mokhoa oa ho feto-fetoha o hloka tšebeliso ea li-capacitor tsa kantle tsa kristale bakeng sa ho latela melao. Lintlha tse ling li ka fumanoa ho errata ea sesebelisoa.
(2) E loketse litsamaiso tse shebaneng le ho latela EN 300 220, EN 303 131, EN 303 204, FCC CFR47 Karolo ea 15, ARIB STD-T108.
8.12 861 MHz ho isa ho 1054 MHz - PLL Phase Noise Wideband Mode
Ha ho lekanngoa moralo oa litšupiso ka Tc = 25 °C, VDDS = 3.0 V.

PARAMETER	LITEKO MAEMO	MIN	TYP	MAX	THUTO
Lerata la mohato ho lihlopha tsa 868- le 915-MHz 20 kHz PLL loop bandwidth	± 10 kHz e fokotsehile	–74			dBc/Hz
	± 100 kHz e fokotsehile	–97			dBc/Hz
	± 200 kHz e fokotsehile	–107			dBc/Hz
	± 400 kHz e fokotsehile	–113			dBc/Hz
	± 1000 kHz e fokotsehile	–120			dBc/Hz
	± 2000 kHz e fokotsehile	–127			dBc/Hz
	± 10000 kHz e fokotsehile	–141			dBc/Hz

8.13 861 MHz ho isa ho 1054 MHz - PLL Phase Noise Narrowband Mode
Ha ho lekanngoa moralo oa litšupiso ka Tc = 25 °C, VDDS = 3.0 V.

PARAMETER	LITEKO MAEMO	MIN	TYP	MAX	THUTO
Lerata la mohato ho lihlopha tsa 868- le 915-MHz 150 kHz PLL loop band e nang le	± 10 kHz e fokotsehile	–93			dBc/Hz
	± 100 kHz e fokotsehile	–93			dBc/Hz
	± 200 kHz e fokotsehile	–95			dBc/Hz
	± 400 kHz e fokotsehile	–104			dBc/Hz
	± 1000 kHz e fokotsehile	–121			dBc/Hz
	± 2000 kHz e fokotsehile	–130			dBc/Hz
	± 10000 kHz e fokotsehile	–140			dBc/Hz

8.14 Litšobotsi tsa Nako le Phetoho
8.14.1 Hlahisa Nako bocha

PARAMETER	MIN	TYP	MAX	THUTO
RESET_N nako e tlase	1			µs

8.14.2 Nako ea ho Tsoha
E lekanyelitsoe ho sebetsa mocheso oa moea o sa lefelloeng ka VDDS = 3.0 V (ntle le haeba ho boletsoe ka tsela e 'ngoe). Linako tse thathamisitsoeng mona ha li kenyelletse litaba tsa software.

PARAMETER	LITEKO MAEMO	MIN	TYP	MAX	THUTO
MCU, Khutlisa ho sebetsa (1)		850 - 4000			µs
MCU, Koala ho ea ho Active(1)		850 - 4000			µs
MCU, Standby to Active		165			µs
MCU, E sebetsa ho Standby		39			µs

E lekanyelitsoe ho sebetsa mocheso oa moea o sa lefelloeng ka VDDS = 3.0 V (ntle le haeba ho boletsoe ka tsela e 'ngoe). Linako tse thathamisitsoeng mona ha li kenyelletse litaba tsa software.

PARAMETER	LITEKO MAEMO	MIN TYP MAX	THUTO
MCU, ha e sebetse ho sebetsa		15	µs

(1) Nako ea ho tsoha e itšetlehile ka tefiso e setseng ho VDDR capacitor ha o qala sesebelisoa, kahoo sesebelisoa se bile nako e kae ho Reset kapa Shutdown pele se qala hape. Nako ea ho tsoha e eketseha ka boleng bo phahameng ba capacitor.

8.14.3 Litlhaloso tsa oache
8.14.3.1 48 MHz Crystal Oscillator (XOSC_HF) le ho nepahala ha maqhubu a RF
Mojule ona o na le kristale ea 48 MHz e hokahaneng le oscillator. Nakong ea tlhahlobo ea tlhahiso ea module, sehlopha sa ka hare sa capacitor se kenyang kristale se lokisoa ho fokotsa phoso ea maqhubu a kristale. Teko ea tlhahiso e boetse e fokotsa phoso ea maqhubu a RF mochesong oa kamore ka ho fetola lentsoe la RF frequency (PLL). Tokiso ena ea pele ea maqhubu a RF e sebelisoa ho software (haeba e nolofalitsoe) ho lefa maqhubu a RF ho ipapisitse le khakanyo ea ho hoholeha ha mocheso oa kristale. E lekantsoe ka moralo oa litšupiso tsa Texas Instruments ka Tc = 25 °C, VDDS = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe.

PARAMETER	MIN	TYP	MAX	THUTO
Leqhubu la kristale	48			MHz
Nako ea ho qala ea Crystal oscillator(2)	200			µs
48 MHz ho nepahala ha maqhubu a pele ho 25 °	-5	2	5	ppm
48 MHz maqhubu a botsitso, mocheso hoholeha -40 ° ho 105 °	-16		18	ppm
Crystal botsofali, lilemo tse 5	-2		2	ppm
Crystal botsofali, lilemo tse 10	-4		2	ppm
Ho nepahala ha RF Frequency ho kenyelletsa software e ka hare e lefelletseng ho hoholeha ha mocheso, ho sa kenyeletsoe botsofali, -40 ° ho isa ho 65 °. E ipapisitse le khakanyo ea ho hoholeha ha kristale ho theosa le mocheso ho tsoa ho sebopeho sa kristale ea moetsi.	-10		10	ppm

Ho hlahloba kapa ho emisa kristale ka tsela e 'ngoe ha converter ea DC / DC e sebetsa ho ka baka tšenyo e sa feleng ho sesebelisoa.

Nako ea ho qala ho sebelisa mokhanni oa motlakase o fanoeng ke TI. Nako ea ho qala e ka eketseha haeba mokhanni a sa sebelisoe.

8.14.3.2 48 MHz RC Oscillator (RCOSC_HF)
E lekantsoe ka moralo oa litšupiso tsa Texas Instruments ka Tc = 25 °C, VDDS = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe.

	MIN	TYP	MAX	THUTO
Khafetsa	48			MHz
Ho nepahala ha maqhubu a sa lekanngoang	±1			%
Ho nepahala ha maqhubu (1)	±0.25			%
Nako ea ho qala	5			µs

Ho nepahala ho amanang le mohloli oa calibration (XOSC_HF)

8.14.3.3 2 MHz RC Oscillator (RCOSC_MF)
E lekantsoe ka moralo oa litšupiso tsa Texas Instruments ka Tc = 25 °C, VDDS = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe.

	MIN	TYP	MAX	THUTO
Maqhubu a lekantsoeng	2			MHz
Nako ea ho qala	5			µs

8.14.3.4 32.768 kHz Crystal Oscillator (XOSC_LF) le ho nepahala ha RTC
Mojule ona o na le kristale ea 32 kHz e hokahaneng le oscillator. Nakong ea teko ea tlhahiso ea module, RTC (Real Time Clock) e nkiloeng ho 32 kHz crystal oscillator e lekanngoa ka roome tempertaure. Sena se etsoa ho fokotsa phoso ea RTC e bakoang ke phoso ea pele ea kristale ea 32 kHz. Tokiso ena ea pele ea RTC e sebelisoa ho software (haeba e nolofalitsoe) ho lefella RTC ho latela tekanyo ea mocheso oa kristale. E lekantsoe ka moralo oa litšupiso tsa Texas Instruments ka Tc = 25 °C, VDDS = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe.

	MIN	TYP	MAX	THUTO
Leqhubu la kristale	32.768			kHz
Ho nepahala ha maqhubu a pele ho 25°	-20	20		ppm
32kHz botsofali ba kristale, selemo sa pele	-3	3		ppm
Ho nepahala ha Sesupanako sa Nako ea 'Nete (RTC) ho sebelisoa matšeliso a mocheso bakeng sa 32kHz xtal (haeba e nolofalitsoe ke software), ho sa kenyeletsoe botsofali, -40° ho isa ho 105° degrees. E ipapisitse le khakanyo ea ho hoholeha ha kristale ho theosa le mocheso ho tsoa ho sebopeho sa kristale ea moetsi.	-100	50		ppm
Ho nepahala ha Sesupanako sa Nako ea 'Nete (RTC) ho sebelisoa matšeliso a mocheso bakeng sa 32kHz xtal (haeba e nolofalitsoe ke software), ho sa kenyeletsoe botsofali, -40° ho isa ho 65° degrees. E ipapisitse le khakanyo ea ho hoholeha ha kristale ho theosa le mocheso ho tsoa ho sebopeho sa kristale ea moetsi.	-50	50		ppm

8.14.3.5 32 kHz RC Oscillator (RCOSC_LF)
E lekantsoe ka moralo oa litšupiso tsa Texas Instruments ka Tc = 25 °C, VDDS = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe.

		MIN	TYP	MAX	THUTO
Khafetsa		32.8			kHz
RTC e lekantsoeng phapang(1)	E lekoa nako le nako khahlanong le XOSC_HF(2)	±600(3)			ppm
Coefficient ea mocheso		50			ppm/°C

Ha u sebelisa RCOSC_LF e le mohloli oa oache e tlaase ea maqhubu (SCLK_LF), ho nepahala ha SCLK_LF-derived Real Time Clock (RTC) ho ka ntlafatsoa ka ho lekanya RCOSC_LF e amanang le XOSC_HF le ho lefella lebelo la RTC tick. Ts'ebetso ena e fumaneha ka mokhanni oa Power o fanoeng ke TI.
Software ea mokhanni oa TI e lekanya RTC nako le nako ha XOSC_HF e sebetsa.
Phapang ea lisebelisoa tse ling e ka feta 1000 ppm. Khatiso e eketsehileng e ke ke ea ntlafatsa phapang.

8.14.4 Litšobotsi tsa Synchronous Serial Interface (SSI).

8.14.4.1.1 Litšobotsi tsa Synchronous Serial Interface (SSI). holim'a mocheso oa mocheso oa moea o sa lefelloeng (ntle le haeba ho boletsoe ka tsela e 'ngoe)

PARAMETER NO.	PARAMETER		MIN	TYP	MAX	THUTO
S1	tclk_per	Nako ea potoloho ea SSIClk	12		65024	Lioache tsa Sistimi (2)
S2(1)	tclk_high	SSIClk nako e phahameng	0.5			tclk_per
S3(1)	tclk_tlase	SSIClk nako e tlase	0.5			tclk_per

Sheba litšoantšo tsa nako tsa SSI , le .

Ha o sebelisa mokhanni oa Matla o fanoeng ke TI, oache ea sistimi ea SSI e lula e le 48 MHz.

8.14.5 UART
8.14.5.1 Litšobotsi tsa UART
holim'a mocheso oa mocheso oa moea o sa lefelloeng (ntle le haeba ho boletsoe ka tsela e 'ngoe)

PARAMETER	MIN	TYP	MAX	THUTO
Sekhahla sa UART	3			MBaud

8.15 Litšobotsi tsa Peripheral
8.15.1 ADC
8.15.1.1 Litšobotsi tsa Analoji-to-Digital Converter (ADC).
Tc = 25 °C, VDDS = 3.0 V le voltage scaling e lumelletsoe, ntle le ha ho boletsoe ka tsela e 'ngoe. (1)
Linomoro tsa ts'ebetso li hloka tšebeliso ea offset le ho fumana liphetoho ho software ke bakhanni ba ADC ba fanoeng ke TI.

PARAMETER		LITEKO MAEMO	MIN	TYP	MAX	THUTO
	Keletso voltage fapaneng		0		VDDS	V
	Qeto		12			Bits
	Sample Rate		200			ksps
	Offset	Ka hare 4.3 V tšupiso e lekanang(2)	±2			LSB
	Fumana phoso	Ka hare 4.3 V tšupiso e lekanang(2)	±7			LSB
DNL(4)	Phapang e sa lekanyetsoang		>–1			LSB
INL	Ntho e sa tsitsang		±4			LSB
ENOB	Palo e sebetsang ea likotoana	Ka hare 4.3 V referense e lekanang(2), 200 kSampNyane, 9.6 kHz molumo oa ho kenya	9.8			Bits
		Ka hare 4.3 V referense e lekanang(2), 200 kSampNyane, 9.6 kHz molumo oa ho kenya, DC/DC e lumelletsoe	9.8
		VDDS e le tšupiso, 200 kSamptlase, 9.6 kHz molumo oa ho kenya	10.1
		Bukana ea ka hare, voltage holofetse, 32 sampka karolelano, 200 kSamptlase/s, molumo oa ho kenya 300 Hz	11.1
		Bukana ea ka hare, voltage scaling e holofetse, 14-bit mode, 200 kSamptlase/s, molumo oa ho kenya 600 Hz (5)	11.3
		Bukana ea ka hare, voltage scaling e holofetse, 15-bit mode, 200 kSamptlase/s, molumo oa ho kenya 150 Hz (5)	11.6
THD	Kakaretso ea ho sotha ha harmonic	Ka hare 4.3 V referense e lekanang(2), 200 kSamptlase, 9.6 kHz molumo oa ho kenya	–65			dB
		VDDS e le tšupiso, 200 kSamptlase, 9.6 kHz molumo oa ho kenya	–70
		Bukana ea ka hare, voltage scaling ba holofetse, 32 sampka karolelano, 200 kSamptlase/s, molumo oa ho kenya 300 Hz	–72
SINAD, SNDR	Karolelano ea lets'oao le lerata le ho sotha	Ka hare 4.3 V referense e lekanang(2), 200 kSamptlase, 9.6 kHz molumo oa ho kenya	60			dB
		VDDS e le tšupiso, 200 kSamptlase, 9.6 kHz molumo oa ho kenya	63
		Bukana ea ka hare, voltage scaling ba holofetse, 32 sampka karolelano, 200 kSamptlase/s, molumo oa ho kenya 300 Hz	68
SFDR	Spurious-free dynamic range	Ka hare 4.3 V referense e lekanang(2), 200 kSamptlase, 9.6 kHz molumo oa ho kenya	70			dB
		VDDS e le tšupiso, 200 kSamptlase, 9.6 kHz molumo oa ho kenya	73
		Bukana ea ka hare, voltage scaling ba holofetse, 32 sampka karolelano, 200 kSamptlase/s, molumo oa ho kenya 300 Hz	75
	Nako ea ho sokoloha	Phetoho ea serial, nako-to-output, 24 MHz oache	50			Li-Clock Cycles
	Tšebeliso ea hona joale	Ka hare 4.3 V tšupiso e lekanang(2)	0.40			mA
	Tšebeliso ea hona joale	VDDS e le litšupiso	0.57			mA
	Reference voltage	Tšebeliso e tšoanang e tsitsitseng ea ka hare (input voltage sekala e nolofaditswe). Bakeng sa ho nepahala ho hoholo, phetoho ea ADC e lokela ho qalisoa ka TI-RTOS API e le ho kenyelletsa lintlha tsa matšeliso a phaello / offset a bolokiloeng ho FCFG1.	4.3(2) (3)			V
	Reference voltage	Referense e tsitsitseng ea ka hare (input voltage qhekella bokooa). Bakeng sa ho nepahala ka ho fetisisa, phetoho ea ADC e lokela ho qalisoa ka TI-RTOS API e le hore e kenyelle lintlha tsa matšeliso a phaello / offset a bolokiloeng ho FCFG1. Boleng bona bo tsoa ho boleng bo lekantsoeng (4.3 V) ka tsela e latelang: V_ref = 4.3 V × 1408 / 4095	1.48			V
	Reference voltage	VDDS joalo ka referense, input voltage scaling e lumelletsoe	VDDS			V
	Reference voltage	VDDS joalo ka referense, input voltage scaling e holofetse	VDDS / 2.82(3)			V

Tc = 25 °C, VDDS = 3.0 V le voltage scaling e lumelletsoe, ntle le ha ho boletsoe ka tsela e 'ngoe. (1)
Linomoro tsa ts'ebetso li hloka tšebeliso ea offset le ho fumana liphetoho ho software ke bakhanni ba ADC ba fanoeng ke TI.

PARAMETER		LITEKO MAEMO	MIN TYP MAX	THUTO
	Kenyelletso ea ho kenya	200 kSamples/s, voltage scaling e lumelletsoe. Capacitive input, Input impedance e itšetlehile ka sampling frequency le sampnako e telele	>1	MΩ

Ho sebelisa IEEE Std 1241-2010 bakeng sa mantsoe le mekhoa ea liteko
Letšoao la ho kenya le fokotsehile ka hare pele ho phetoho, joalo ka ha eka ke voltagboholo ba eona e ne e le 0 ho 4.3 V

E sebelisitsoeng voltage tlameha ho ba ka hare ho Absolute Maximum Ratings ka linako tsohle
Ha ho likhoutu tse sieo
ADC_output = Σ(4 nsamples ) >> n, n = tse ling tse lakatsehang

8.15.2 DAC
8.15.2.1 Litšobotsi tsa Digital-to-Analog Converter (DAC).
Tc = 25 °C, VDDS = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe.

PARAMETER		LITEKO MAEMO	MIN	TYP	MAX	THUTO
Kakaretso Parameters
	Qeto		8			Bits
VDDS	Phepelo voltage	Mojaro ofe kapa ofe, V_REF, pele o tjhaja, pompo ya ho tjhaja ya DAC HO BUDITSE	1.8		3.8	V
		Mojaro oa Kantle(4), V_REF, TSHAFATSO pele ho tefo, pompo ea ho tjhaja ka DAC E TLOHA	2.0		3.8
		Mojaro ofe kapa ofe, V_REF = DCOUPL, pele ho tefiso ON	2.6		3.8
FDAC	Maqhubu a oache	Buffer ON (e khothaletsoa bakeng sa mojaro o kantle)	16		250	kHz
		Buffer OFF (moroalo o ka hare)	16		1000
	Moqtage sephetho sa ho lokisa nako	V_REF = VDDS, buffer OFF, mojaro o ka hare	13			1 / F_DAC
		V_REF = VDDS, buffer ON, kantle capacitive load = 20 pF(3)	13.8
	Mojaro oa ka ntle oa capacitive			20	200	pF
	Mojaro o hanyetsang ka ntle		10			MΩ
	Nako e khutšoanyane ea potoloho		400			µA
ZMAX	Max output impedance Vref = VDDS, buffer ON, CLK 250 kHz	VDDS = 3.8 V, DAC charge-pump OFF	50.8			k
		VDDS = 3.0 V, DAC tefello-pompo ON	51.7
		VDDS = 3.0 V, DAC charge-pump OFF	53.2
		VDDS = 2.0 V, DAC tefello-pompo ON	48.7
		VDDS = 2.0 V, DAC charge-pump OFF	70.2
		VDDS = 1.8 V, DAC tefello-pompo ON	46.3
		VDDS = 1.8 V, DAC charge-pump OFF	88.9
Mojaro o ka Hare - Mofani oa Nako e Tsoelang Pele / Motlatsi oa Matla a Tlase a koetsoeng
DNL	Phapang e sa lekanyetsoang	V_REF = VDDS, mojaro = Moetsi oa Nako e Tsoelang Pele kapa Mofani oa Matla a Tlase a koetsoeng F_DAC = 250 kHz	±1			LSB(1)
	Phapang e sa lekanyetsoang	V_REF = VDDS, mojaro = Moetsi oa Nako e Tsoelang Pele kapa Mofani oa Matla a Tlase a koetsoeng F_DAC = 16 kHz	±1.2
	Phoso ea Offset (2) Mojaro = Mofani oa Nako e Tsoelang Pele	V_REF = VDDS = 3.8 V	±0.64			LSB(1)
		V_REF = VDDS= 3.0 V	±0.81
		V_REF = VDDS = 1.8 V	±1.27
		V_REF = DCOUPL, pele ho tefiso ON	±3.43
		V_REF = DCOUPL, ho tjhaja pele HO TLWA	±2.88
		V_REF = ADCREF	±2.37
	Phoso ea Offset (2) Mojaro = Motlatsi o Koetsoeng oa Matla a Tlase	V_REF = VDDS= 3.8 V	±0.78			LSB(1)
		V_REF = VDDS = 3.0 V	±0.77
		V_REF = VDDS= 1.8 V	±3.46
		V_REF = DCOUPL, pele ho tefiso ON	±3.44
		V_REF = DCOUPL, ho tjhaja pele HO TLWA	±4.70
		V_REF = ADCREF	±4.11
	Max code output voltage ho fapana(2) Mojaro = Continuous Time Comparator	V_REF = VDDS = 3.8 V	±1.53			LSB(1)
		V_REF = VDDS = 3.0 V	±1.71
		V_REF = VDDS= 1.8 V	±2.10
		V_REF = DCOUPL, pele ho tefiso ON	±6.00
		V_REF = DCOUPL, ho tjhaja pele HO TLWA	±3.85
		V_REF = ADCREF	±5.84

Tc = 25 °C, VDDS = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe.

PARAMETER		LITEKO MAEMO	MIN TYP MAX	THUTO
	Max code output voltage feto-fetoha (2) Mojaro = Low Power Clocked Comparator	V_REF = VDDS= 3.8 V	±2.92	LSB(1)
		V_REF =VDDS= 3.0 V	±3.06
		V_REF = VDDS= 1.8 V	±3.91
		V_REF = DCOUPL, pele ho tefiso ON	±7.84
		V_REF = DCOUPL, ho tjhaja pele HO TLWA	±4.06
		V_REF = ADCREF	±6.94
	Sephetho voltage range(2) Mojaro = Continuous Time Comparator	V_REF = VDDS = 3.8 V, khoutu 1	0.03	V
		V_REF = VDDS = 3.8 V, khoutu 255	3.62
		V_REF = VDDS= 3.0 V, khoutu 1	0.02
		V_REF = VDDS= 3.0 V, khoutu 255	2.86
		V_REF = VDDS= 1.8 V, khoutu 1	0.01
		V_REF = VDDS = 1.8 V, khoutu 255	1.71
		V_REF = DCOUPL, ho tjhaja esale pele, khoutu 1	0.01
		V_REF = DCOUPL, ho tjhaja esale pele, khoutu 255	1.21
		V_REF = DCOUPL, ho tjhaja pele HO BUTSE, khoutu 1	1.27
		V_REF = DCOUPL, ho tjhaja pele HO BUTSE, khoutu 255	2.46
		V_REF = ADCREF, khoutu 1	0.01
		V_REF = ADCREF, khoutu 255	1.41
	Sephetho voltage range(2) Mojaro = Low Power Ccked Comparator	V_REF = VDDS = 3.8 V, khoutu 1	0.03	V
		V_REF = VDDS= 3.8 V, khoutu 255	3.61
		V_REF = VDDS= 3.0 V, khoutu 1	0.02
		V_REF = VDDS= 3.0 V, khoutu 255	2.85
		V_REF = VDDS = 1.8 V, khoutu 1	0.01
		V_REF = VDDS = 1.8 V, khoutu 255	1.71
		V_REF = DCOUPL, ho tjhaja esale pele, khoutu 1	0.01
		V_REF = DCOUPL, ho tjhaja esale pele, khoutu 255	1.21
		V_REF = DCOUPL, ho tjhaja pele HO BUTSE, khoutu 1	1.27
		V_REF = DCOUPL, ho tjhaja pele HO BUTSE, khoutu 255	2.46
		V_REF = ADCREF, khoutu 1	0.01
		V_REF = ADCREF, khoutu 255	1.41
Mojaro o kantle
INL	Ntho e sa tsitsang	V_REF = VDDS, F_DAC = 250 kHz	±1	LSB(1)
		V_REF = DCOUPL, F_DAC = 250 kHz	±2
		V_REF = ADCREF, F_DAC = 250 kHz	±1
DNL	Phapang e sa lekanyetsoang	V_REF = VDDS, F_DAC = 250 kHz	±1	LSB(1)
	Phoso ea Offset	V_REF = VDDS= 3.8 V	±0.40	LSB(1)
		V_REF = VDDS= 3.0 V	±0.50
		V_REF = VDDS = 1.8 V	±0.75
		V_REF = DCOUPL, pele ho tefiso ON	±1.55
		V_REF = DCOUPL, ho tjhaja pele HO TLWA	±1.30
		V_REF = ADCREF	±1.10
	Max code output voltagphapano	V_REF = VDDS= 3.8 V	±1.00	LSB(1)
		V_REF = VDDS= 3.0 V	±1.00
		V_REF = VDDS= 1.8 V	±1.00
		V_REF = DCOUPL, pele ho tefiso ON	±3.45
		V_REF = DCOUPL, ho tjhaja pele HO TLWA	±2.10
		V_REF = ADCREF	±1.90

Sephetho voltage fapaneng
Mojaro = Mofani oa Matla a Tlase a koetsoeng

V_REF = VDDS = 3.8 V, khoutu 1

0.03

1 LSB (VREF 3.8 V/3.0 V/1.8 V/DCUPL/ADCREF) = 14.10 mV/11.13 mV/6.68 mV/4.67 mV/5.48 mV

E kenyelletsa comparator offset
Mojaro> 20 pF e tla eketsa nako ea ho lokisa
Keysight 34401A Multimeter

8.15.3 Tekanyo ea Mocheso le Betri
8.15.3.1 Sensora ea Mocheso
E lekantsoe ka moralo oa litšupiso tsa Texas Instruments ka Tc = 25 °C, VDDS = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe.

PARAMETER	LITEKO MAEMO	MIN	TYP	MAX	THUTO
Qeto		2			°C
Ho nepahala	-40 °C ho isa ho 0 °C	±5.0			°C
Ho nepahala	0 °C ho isa ho 105 °C	±3.5			°C
Phepelo voltage coefficient(1)		3.6			°C/V

Sensor ea mocheso e lefshoa ka bo eona bakeng sa phapang ea VDDS ha e sebelisa mokhanni oa mocheso o fanoeng ke TI.

8.15.3.2 Battery Monitor
E lekantsoe ka moralo oa litšupiso tsa Texas Instruments ka T = 25 °C, ntle le ha ho boletsoe ka tsela e 'ngoe.

PARAMETER	LITEKO MAEMO	MIN	TYP	MAX	THUTO
Qeto		25			mV
Range		1.8		3.8	V
Integral nonlinearity (max)		23			mV
Ho nepahala	VDDS = 3.0 V	22.5			mV
Phoso ea Offset		-32			mV
Fumana phoso		-1			%

8.15.4 Bapisa
8.15.4.1 Comparator e Koetsoeng ea Matla a Tlase
T = 25 °C, V = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe.

PARAMETER	LITEKO MAEMO	MIN	TYP	MAX	THUTO
Keletso voltage fapaneng		0		VDDS	V
Maqhubu a oache		SCLK_LF
Tšupiso ea ka hare voltage(1)	Ho sebelisa ka hare ho DAC le VDDS joalo ka referense voltage, DAC khoutu = 0 – 255	0.024 - 2.865			V
Offset	E lekantsoe ho V_DDS / 2, e kenyelletsa phoso e tsoang ho DAC ea kahare	±5			mV
Nako ea ho etsa qeto	Mohato ho tloha ho -50 mV ho isa ho 50 mV	1			Potoloho ea Tshupanako

(1) Sebapi se ka sebelisa li-bits tsa 8 tsa ka hare tsa DAC e le boitsebiso ba eona. Phatlalatso ea DAC voltage range itšetlehile ka referense voltage khethiloe. Bona

8.15.4.2 Sebapi sa Nako se Tsoelang Pele
Tc = 25 ° C, VDDS = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe.

PARAMETER	LITEKO MAEMO	MIN	TYP	MAX	THUTO
Keletso voltagmofuta oa e(1)		0		VDDS	V
Offset	E lekantsoe ho V_DDS / 2	±5			mV
Nako ea ho etsa qeto	Mohato ho tloha ho -10 mV ho isa ho 10 mV	0.70			µs
Tšebeliso ea hona joale	Tshupiso ya ka hare	8.0			µA

Tlatsetso voltage ka hlahisoa ka ntle le ho hokahanngoa ho pholletsa le I/Os kapa ka hare ho referense voltage ka hlahisoa ho sebelisoa DAC

8.15.5 Mohloli oa Hona Joale
8.15.5.1 Mohloli oa Hona Joale o Reriloeng
Tc = 25 °C, VDDS = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe.

PARAMETER	LITEKO MAEMO	MIN	TYP	MAX	THUTO
Mohloli oa hona joale oa mefuta e ka khonehang ea tlhahiso (logarithmic range)		0.25 - 20			µA
Qeto		0.25			µA

8.15.6 GPIO
8.15.6.1 Litšobotsi tsa GPIO DC
Litekanyo CBSed ho PG2.1:

PARAMETER	LITEKO MAEMO	MIN	TYP	MAX	THUTO
T_A = 25 °C, V_DDS =1.8 V
GPIO VOH ka mojaro oa 8 mA	IOCURR = 2, li-GPIO tsa koloi e phahameng feela	1.56			V
GPIO VOL ka mojaro oa 8 mA	IOCURR = 2, li-GPIO tsa koloi e phahameng feela	0.24			V
GPIO VOH ka mojaro oa 4 mA	IOCURR = 1	1.59			V
GPIO VOL ka mojaro oa 4 mA	IOCURR = 1	0.21			V
GPIO hula hona joale	Mokhoa oa ho kenya, ho hula o nolofalitsoe, Vpad = 0 V	73			µA
GPIO ea ho theola hajoale	Mokhoa oa ho kenya, ho hula o nolofalitsoe, Vpad = VDDS	19			µA
Phetoho ea GPIO e tlase ho isa holimo, e nang le hysteresis	IH = 1, phetoho voltage bakeng sa tlhahiso e baloa joalo ka 0 → 1	1.08			V
Phetoho ea GPIO e phahameng ho isa tlase, e nang le hysteresis	IH = 1, phetoho voltage bakeng sa tlhahiso e baloa joalo ka 1 → 0	0.73			V
GPIO e kenyang hysteresis	IH = 1, phapang pakeng tsa 0 → 1 le 1 → lintlha tse 0	0.35			V
T_A = 25 °C, V_DDS =3.0 V
GPIO VOH ka mojaro oa 8 mA	IOCURR = 2, li-GPIO tsa koloi e phahameng feela	2.59			V
GPIO VOL ka mojaro oa 8 mA	IOCURR = 2, li-GPIO tsa koloi e phahameng feela	0.42			V
GPIO VOH ka mojaro oa 4 mA	IOCURR = 1	2.63			V
GPIO VOL ka mojaro oa 4 mA	IOCURR = 1	0.40			V
T_A = 25 °C, V_DDS =3.8 V
GPIO hula hona joale	Mokhoa oa ho kenya, ho hula o nolofalitsoe, Vpad = 0 V	282			µA
GPIO ea ho theola hajoale	Mokhoa oa ho kenya, ho hula o nolofalitsoe, Vpad = VDDS	110			µA
Phetoho ea GPIO e tlase ho isa holimo, e nang le hysteresis	IH = 1, phetoho voltage bakeng sa tlhahiso e baloa joalo ka 0 → 1	1.97			V
Phetoho ea GPIO e phahameng ho isa tlase, e nang le hysteresis	IH = 1, phetoho voltage bakeng sa tlhahiso e baloa joalo ka 1 → 0	1.55			V
GPIO e kenyang hysteresis	IH = 1, phapang pakeng tsa 0 → 1 le 1 → lintlha tse 0	0.42			V
T_A = 25 ° C
VIH	Phaello e tlase ea GPIO ea molumotage ka tšeptjoang e hlalosoa e le a Phahameng	0.8*V_DDS			V
VIL	Phaello e phahameng ka ho fetesisa ea GPIOtage ka tšeptjoang e hlalosoa e le a Tlase	0.2*V_DDS			V

8.16 Litšobotsi tse Tloaelehileng
Litekanyo tsohle karolong ena li etsoa ka Tc = 25 °C le VDDS = 3.0 V, ntle le haeba ho boletsoe ka tsela e 'ngoe. Sheba Maemo a Tšebetso a khothalelitsoeng bakeng sa meeli ea lisebelisoa. Litefiso tse fetang meeli ena ke tsa litšupiso feela.
8.16.1 MCU ea Hona joale

8.16.2 RX ea Hona joale

8.16.3 TX Hajoale

Lethathamo la 8-1. E Tloaelehileng TX Hona Joale le Matla a Output

CC1312PSIP ho 915 MHz, VDDS = 3.0 V (E lekantsoe ho LP-EM-CC1312PSIP)
txPower	TX Power Setting (SmartRF Studio)	Matla a Sehlahisoa a Tloaelehileng [dBm]	Tšebeliso e Tloaelehileng Hona Joale [mA]
0x013F	14	13.8	34.6
0x823F	12.5	12.2	24.9
0x7828	12	11.8	23.5
0x7A15	11	10.9	21.6
0x4C0D	10	10.1	20.0
0x400A	9	9.5	19.1
0x449A	8	8.1	17.1
0x364D	7	6.8	15.3
0x2892	6	6.3	14.8
0x20DC	5	4.9	13.7
0x28D8	4	4	12.6
0x1C46	3	3.7	11.7
0x18D4	2	2.8	11.5
0x16D1	1	0.8	10.6
0x16D0	0	0.3	10.3
0x0CCB	-3	-3.4	8.6
0x0CC9	-5	-5.4	7.9
0x08C7	-7	-8	7.3
0x0AC5	-10	-11.7	6.6
0x08C3	-15	-17.1	5.9
0x08C2	-20	-20.9	5.6

8.16.4 RX Tshebetso

8.16.5 TX Tshebetso

8.16.6 Ts'ebetso ea ADC

Tlhaloso e Felletseng

9.1 Ho fetaview
Karolo ea 4 e bonts'a li-module tsa mantlha tsa sesebelisoa sa CC1312PSIP.
9.2 CPU ea sistimi
-M4F sistimi ea CPU, e tsamaisang lisebelisoa
ts'ebeliso le likarolo tse holimo tsa li-stacks tsa radio protocol.
CC1312PSIP SimpleLink ™ Wireless MCU e na le Arm Cortex
Sistimi ea CPU ke motheo oa sethala sa ts'ebetso e phahameng, se theko e tlase se fihlelang litlhoko tsa sistimi ea ts'ebetso e fokolang ea mohopolo, le tšebeliso e tlase ea matla, ha e ntse e fana ka ts'ebetso e ikhethang ea computational le karabelo e ikhethang ea sistimi ho litšitiso.
Likarolo tsa eona li kenyelletsa tse latelang:

Moralo oa ARMv7-M o ntlafalitsoe bakeng sa lits'ebetso tse kentsoeng ka maoto a manyane
Arm Thumb -2 e tsoakiloeng ea 16- le 32-bit ea litaelo e fana ka ts'ebetso e phahameng e lebelletsoeng ea 32-bit Arm core ka boholo ba mohopolo o kopaneng.
Ts'ebetso ea khoutu e potlakileng e lumella ho eketsa nako ea mokhoa oa ho robala
Ts'ebetso e ikemiselitseng, ea ts'ebetso e phahameng ea ts'ebetso bakeng sa lits'ebetso tse bohlokoa ka nako
Single-cycle ho atisa litaelo le hardware arola
Karohano ea lisebelisoa le tšebetso e potlakileng ea li-signal tsa dijithale lia bokellana
Saturating arithmetic bakeng sa ts'ebetso ea matšoao
IEEE 754-compliant single-precision Floating Point Unit (FPU)
Setsi sa Tšireletso ea Memori (MPU) bakeng sa lits'ebetso tsa bohlokoa tsa polokeho
Debug e felletseng e tsamaisanang le data bakeng sa tlhahiso ea li-watchpoint
- Setsi sa ho lebela le ho latela lintlha (DWT)
– JTAG Debug Access Port (DAP)
- Setsi sa Flash Patch le Breakpoint (FPB)
Tšehetso ea ho batla e fokotsa palo ea lithakhisa tse hlokahalang bakeng sa ho lokisa liphoso le ho lata morao
- Sesebelisoa sa Trace Macrocell Unit (ITM)
- Trace Port Interface Unit (TPIU) e nang le tlhahiso ea terata ea asynchronous (SWO)
E ntlafalitsoe bakeng sa phihlello ea memori ea leqhubu le le leng
E hokahane ka thata ho 8-KB 4-way cache e ncha e sa sebetseng bakeng sa tšebeliso e fokolang ea matla le maemo a ho ema
Tšebeliso ea matla a tlase haholo ka mekhoa e kopaneng ea ho robala
48 MHz tshebetso
1.25 DMIPS ka MHz

9.3 Radio (RF Core)

RF Core ke mojule oa seea-le-moea o feto-fetohang haholo le oa nakong e tlang o nang le processor ea Arm Cortex-M0 e hokahanyang RF ea analog le base-band circuitry, e sebetsanang le data ho tloha le ho tsoa lehlakoreng la CPU ea sistimi, 'me e bokella likotoana tsa tlhaiso-leseling ka har'a pakete e fanoeng. sebopeho. RF core e fana ka boemo bo phahameng, API e thehiloeng ho taelo ho CPU e kholo eo litlhophiso le data li fetisitsoeng ho eona. The Arm Cortex-M0 processor ha e hlophisehe ke bareki mme e hokahantsoe ka mokhanni oa RF o fanoeng ke TI o kenyellelitsoeng le SimpleLink Software Development Kit (SDK).
Motheo oa RF o khona ho sebetsana le likarolo tsa bohlokoa tsa nako ea liprothokholo tsa seea-le-moea ka boithaopo, ka hona ea theola CPU ea mantlha, e fokotsang matla le ho siea lisebelisoa tse ngata bakeng sa ts'ebeliso ea mosebelisi. Ho na le mats'oao a 'maloa a ho laola li-circuit tsa kantle joalo ka li-switch tsa RF kapa li-extender tsa mefuta e ikemetseng.
Mefuta e fapaneng ea liforomo tsa seea-le-moea tsa 'mele li hahiloe ka mokhoa o itseng e le sesebelisoa se hlalositsoeng seea-le-moea moo boitšoaro ba seea-le-moea bo hlalosoang ke litaba tsa seea-le-moea ROM kapa ka liforomo tsa seea-le-moea tseo e seng tsa ROM tse fanoang ka mokhoa oa li-patches tsa firmware tse nang le SimpleLink SDKs. Sena se lumella sethala sa seea-le-moea hore se ntlafatsoe bakeng sa ts'ehetso ea mefuta e tlang ea litekanyetso esita le ka lintlafatso tsa holim'a moea (OTA) ha li ntse li sebelisa silicon e tšoanang.
Hlokomela
Ha se mefuta eohle ea likarolo, maqhubu, litekanyetso tsa data, le lifomate tsa modulation tse hlalositsoeng khaolong ena tse tšehetsoeng. Ha nako e ntse e ea, TI e ka khona ho etsa liforomo tse ncha tsa seea-le-moea (PHYs) bakeng sa sesebelisoa mme e fane ka linomoro tsa ts'ebetso bakeng sa li-PHY tse khethiloeng leqepheng la data. Liforomo tsa seea-le-moea tse tšehelitsoeng bakeng sa sesebelisoa se itseng, ho kenyeletsoa li-setting tse ntlafalitsoeng hore li sebelisoe le mokhanni oa TI RF, li kenyelelitsoe sesebelisoa sa SmartRF Studio se nang le linomoro tsa ts'ebetso ea lifomate tse khethiloeng tse fumanehang karolong ea Specifications.

9.3.1 Liforomo tsa Radio tsa Proprietary
Seea-le-moea sa CC1312PSIP se ka ts'ehetsa mefuta e mengata ea lifomate tsa seea-le-moea sa 'mele ka sete ea lisebelisoa tsa lisebelisoa tse kopantsoeng le firmware e fumanehang sesebelisoa sa ROM, se koahelang litlhoko tse fapaneng tsa bareki bakeng sa ho ntlafatsa ho ea ho liparamente tse kang lebelo kapa kutlo. Sena se lumella ho feto-fetoha ha maemo ho hokahaneng ha seea-le-moea ka bobeli ho sebetsa le liprothokholo tsa khale hammoho le ho hlophisa boitšoaro ho latela litlhoko tse ikhethileng tsa ts'ebeliso.
Lethathamo la 9-1 le fana ka tlhaloso e nolofalitsoengview ea likarolo tsa mefuta e fapaneng ea radio e fumanehang ho ROM. Liforomo tse ling tsa seea-le-moea li ka fumaneha ka mokhoa oa li-patches tsa radio firmware kapa mananeo ka Software Development Kit (SDK) mme e ka kopanya likarolo ka mokhoa o fapaneng, hammoho le ho eketsa likarolo tse ling.
Lethathamo la 9-1. Feature Support

Sebopeho	Mokhoa o ka sehloohong oa 2-(G)FSK	Litefiso tse phahameng tsa data	Litefiso tse tlase tsa data	SimpleLink™ Nako e telele
Ketapele e ka reroang, mantsoe a sync, le CRC	Ee	Ee	Ee	Che
Lenaneo la ho amohela li-bandwidth	Ee	Ee	Ho joalo (ho fihla ho 4 kHz)	Ee
Lintlha / Sekhahla sa matšoao(3)	20 ho isa ho 1000 kbps	≤ 2 Msps	≤ 100 ksps	≤ 20 ksps
Sebopeho sa modulation	2-(G)FSK	2-(G)FSK 4-(G)FSK	2-(G)FSK 4-(G)FSK	2-(G)FSK
Dual Sync Word	Ee	Ee	Che	Che
Carrier Sense (1) (2)	Ee	Che	Che	Che
Tlhaloso ea Selelekela(2)	Ee	Ee	Ee	Che
Ho soeufala ha data	Ee	Ee	Ee	Ee
Digithale RSSI	Ee	Ee	Ee	Ee
CRC sefa	Ee	Ee	Ee	Ee
Direct-Sequence spread spectrum (DSSS)	Che	Che	Che	1:2 1:4 1:8
Tsoela pele ho lokisa phoso (FEC)	Che	Che	Che	Ee
Sesupo sa Boleng ba Khokahano (LQI)	Ee	Ee	Ee	Ee

Carrier Sense e ka sebelisoa ho kenya ts'ebetsong ea HW-controlled-before-talk (LBT) le Clear Channel Assessment (CCA) bakeng sa ho lumellana le litlhoko tse joalo ho litekanyetso tsa taolo. Sena se fumaneha ka CMD_PROP_CS radio API.
Carrier Sense le Preamble Detection li ka sebelisoa ho kenya tšebetsong mekhoa ea ho fofonela moo seea-le-moea e leng mosebetsi oa ho boloka motlakase.
Litefiso tsa data ke sesupo feela. Litefiso tsa data tse kantle ho sebaka sena le tsona li ka tšehetsoa. Bakeng sa li-setting tse ling tse ikhethileng, mefuta e nyane e ka tšehetsoa.

9.4 Sehopotso

Memori e fihlang ho 352-KB e sa feto-fetoheng (Flash) e fana ka polokelo bakeng sa khoutu le data. Memori ea Flash e ka har'a sistimi e hlophisehileng ebile e ka hlakoleha. Karolo ea ho qetela ea memori ea flash e tlameha ho ba le karolo ea Customer Configuration (CCFG) e sebelisoang ke boot ROM mme TI e fane ka li-driver ho lokisa sesebelisoa. Tokiso ena e etsoa ka mohloli oa ccfg.c file seo se kenyelelitsoe ho TI eohle e fanoeng examples.
The Ultra-low leakage system static RAM (SRAM) e arotsoe ka li-blocks tse hlano tsa 16-KB 'me e ka sebelisoa bakeng sa polokelo ea data le ho phethahatsa khoutu. Ho bolokoa ha litaba tsa SRAM ho Boemo ba matla a Standby ho lumelloa ka mokhoa oa kamehla 'me ho kenyelelitsoe linomoro tsa tšebeliso ea matla tsa Boemo ba Standby. Ho hlahlojoa ha Parity bakeng sa ho lemoha liphoso tse nyenyane mohopolong ho hahiloe kahare, e leng ho fokotsang liphoso tse bonolo tsa chip-level mme kahoo e eketsa ho tšepahala. Sistimi ea SRAM e lula e qalisoa ho li-zero ha khoutu e etsoa ho tloha boot.
Ho ntlafatsa lebelo la ts'ebetso ea khoutu le matla a tlase ha o etsa khoutu e tsoang mohopolong o sa fetoheng, cache ea 4-way nonassociative 8-KB e nolofalloa ka ho sa feleng ho cache le ho lata litaelo tse baloang ke sistimi ea CPU.
Cache e ka sebelisoa e le RAM ea sepheo se akaretsang ka ho nolofalletsa tšobotsi ena ho Customer Configuration Area (CCFG).
Ho na le 4-KB ea ultra-low leakage SRAM e fumanehang bakeng sa tšebeliso le Sensor Controller Engine eo hangata e sebelisetsoang ho boloka mananeo a Sensor Controller, data le li-parameter tsa tlhophiso. RAM ena e fumaneha hape ke sistimi ea CPU. RAM ea Sensor Controller ha e hlakisoe ho li-zero pakeng tsa ho seta sistimi.
ROM e kenyelletsa kernel ea TI-RTOS le bakhanni ba boemo bo tlase, hammoho le likarolo tsa bohlokoa tsa mekotla ea seea-le-moea e khethiloeng, e lokollang mohopolo oa flash bakeng sa ts'ebeliso. ROM e boetse e na le serial (SPI le UART) bootloader e ka sebelisoang bakeng sa lenaneo la pele la sesebelisoa.

9.5 Sensor Controller

Sensor Controller e na le li-circuitry tse ka sebelisoang ka mokhoa o ikhethileng maemong a Standby le a Active power. Lisebelisoa tse sebakeng sena li ka laoloa ke Sensor Controller Engine, e leng CPU e matlafalitsoeng ka matla. CPU ena e khona ho bala le ho beha leihlo li-sensor kapa ho etsa mesebetsi e meng e ikemetseng; ka hona ho fokotsa tšebeliso ea matla haholo le ho theola sistimi ea CPU.
The Sensor Controller Engine is programmable user with a simple programming language e nang le syntax e tšoanang le C. This programmability e lumella hore sensor polling le mesebetsi e meng e hlalosoe e le sequential algorithms ho fapana le static configuration of complex peripheral modules, timers, DMA, registerable state state. mechini, kapa ho tsamaisa liketsahalo.

Tsela e kholotagke tsena:

Flexibility - data e ka baloa le ho sebetsoa ka mekhoa e se nang moeli ha e ntse e netefatsa matla a tlase haholo.
Mokhoa oa 2 MHz oa matla a tlase o thusa ho sebetsana le li-sensor tsa dijithale tse tlase haholo
Tšebeliso e matla ea lisebelisoa tsa hardware
40-bit accumulator e tšehetsang ho atisa, ho eketsa le ho fetoha
Likhetho tsa ho bonoa le ho lokisa liphoso

Sensor Controller Studio e sebelisetsoa ho ngola, ho lekola, le ho lokisa khoutu ea Sensor Controller. Sesebelisoa se hlahisa khoutu ea mohloli oa mokhanni oa C, eo sesebelisoa sa System CPU se se sebelisang ho laola le ho fapanyetsana data le Sensor Controller. Maemo a tloaelehileng a tšebeliso e ka ba (empa ha a felle feela ho) a latelang:

Bala li-sensor tsa analog u sebelisa ADC e kopaneng kapa li-comparators
Li-sensor tsa dijithale tse sebelisang li-GPIO, SPI, UART, kapa I2 C li fokotsehile hanyane)
Capacitive sensing
Moloko oa waveform
Palo ea matla a tlase haholo (flow metering) Sekena sa senotlolo

Li-peripherals ho Sensor Controller li kenyelletsa tse latelang:

Moetsi oa lioache tse nang le matla a tlase a ka sebelisoa ho tsosa sistimi ea CPU ho tsoa maemong afe kapa afe ao papiso e sebetsang ho eona. DAC e ka lokisoang ea referense ea ka hare e ka sebelisoa hammoho le papiso.
Sehlahisoa sa papiso se ka boela sa sebelisoa ho tsosa tšitiso kapa ADC.
Ts'ebetso ea capacitive sensing e kengoa ts'ebetsong ka ts'ebeliso ea mohloli oa hona joale oa kamehla, converter ea nako ho isa ho dijithale, le sebapi. Nako e tsoelang pele ea ho bapisa nako thibela sena e ka boela ea sebelisoa e le mokhoa o phahameng oa ho nepahala ho feta motlakase o nang le matla a tlaase. Sensor Controller e hlokomela mokhoa oa motheo oa ho latela, hysteresis, filtering, le mesebetsi e meng e amanang le eona ha li-module tsena li sebelisetsoa ho lemoha matla.
ADC ke 12-bit, 200-ksamples/s ADC e nang le lisebelisoa tse robeli le molumo o kentsoengtage referense. ADC e ka hlohlelletsoa ke mehloli e mengata e fapaneng e kenyelletsang li-timers, I/O pins, software le comparator.
Li-module tsa analog li ka hokela ho li-GPIO tse fapaneng tse robeli
SPI master e inehetseng ka lebelo le fihlang ho 6 MHz
Li-peripherals tse ho Sensor Controller le tsona li ka laoloa ho tsoa ho processor ea mantlha ea kopo.

9.6 Mokhoa oa ho ngola

Sesebelisoa sa CC1312PSIP se tla le li-accelerator tsa sejoale-joale tse amanang le li-cryptography, tse fokotsang haholo sebaka sa khoutu le nako ea ts'ebetso bakeng sa ts'ebetso ea cryptographic. E boetse e na le molemo oa ho ba matla a tlase mme e ntlafatsa ho fumaneha le karabelo ea sistimi hobane ts'ebetso ea cryptography e sebetsa ka har'a khoele e ka morao ea hardware.
Hammoho le khetho e kholo ea lilaebrari tsa li-cryptography tse bulehileng tse fanoeng ka Software Development Kit (SDK), sena se lumella hore lits'ebetso tsa IoT tse sireletsehileng le tsa nakong e tlang li hahoe habonolo holim'a sethala. Li-module tsa accelerator tsa hardware ke:

Mojule oa 'Nete oa Random Number Generator (TRNG) o fana ka mohloli oa lerata oa' nete, o sa tsitsang ka sepheo sa ho hlahisa linotlolo, li-vector tsa ho qala (IVs), le litlhoko tse ling tsa linomoro tse sa reroang. TRNG e hahiloe holim'a li-oscillator tse 24 tse hlahisang tlhahiso e sa lebelloang ho fepa potoloho e rarahaneng e sa kopaneng.
Sireletsa Hash Algorithm 2 (SHA-2) ka tšehetso ea SHA224, SHA256, SHA384, le SHA512
Advanced Encryption Standard (AES) e nang le bolelele ba 128 le 256 bit key
Public Key Accelerator - Hardware accelerator e tšehetsang ts'ebetso ea lipalo e hlokahalang bakeng sa elliptic curves ho fihla ho li-bits tse 512 le tlhahiso ea li-key pair tsa RSA ho fihla ho li-bits tse 1024.

Ka ts'ebeliso ea li-module tsena le TI e fane ka bakhanni ba li-cryptography, bokhoni bo latelang bo fumaneha bakeng sa kopo kapa stack:

Merero ea Litumellano tsa Bohlokoa
- Elliptic curve Diffie-Hellman e nang le linotlolo tse tsitsitseng kapa tsa ephemeral (ECDH le ECDHE)
- Elliptic curve Password Authenticated Key Exchange ka Juggling (ECJ-PAKE)
Moloko oa Tshaeno
- Elliptic curve Diffie-Hellman Digital Signature Algorithm (ECDSA)
Tšehetso ea Curve
- Foromo e khuts'oane ea Weierstrass (tšehetso e felletseng ea lisebelisoa), joalo ka:
NIST-P224, NIST-P256, NIST-P384, NIST-P521
Brainpool-256R1, Brainpool-384R1, Brainpool-512R1
sec256r1
- Foromo ea Montgomery (ts'ehetso ea lisebelisoa bakeng sa ho atisa), joalo ka:
Curve25519
SHA2 e thehiloeng ho MACs
- HMAC e nang le SHA224, SHA256, SHA384, kapa SHA512
Thibela mokhoa oa ho sebetsa oa cipher
– AESCCM
– AESGCM
– AESECB
– AESCBC
– AESCBC-MAC
Tsoelo-pele ea linomoro tsa 'nete

Bokhoni bo bong, joalo ka encryption ea RSA le li-signature hammoho le mofuta oa Edwards oa elliptic curves joalo ka Curve1174 kapa Ed25519, le tsona li ka kengoa ts'ebetsong ho sebelisoa li-accelerator tsa hardware tse fanoeng empa ha se karolo ea TI SimpleLink SDK bakeng sa sesebelisoa sa CC1312PSIP.

Linako tse 9.7
Khetho e kholo ea li-timers e fumaneha e le karolo ea sesebelisoa sa CC1312PSIP. Linako tsena ke:

Nako ea Sebele (RTC)
Sebali sa nako sa 70-bit 3-channel se sebetsang ho 32 kHz low frequency system (SCLK_LF)
Sebali sena se fumaneha ka mekhoa eohle ea matla ntle le Shutdown. Sebali sa nako se ka lekanngoa ho lefella ho hoholeha ha maqhubu ha ho sebelisoa LF RCOSC e le oache ea maqhubu a tlase. Haeba ho sebelisoa oache ea kantle ea LF e nang le maqhubu a fapaneng le 32.768 kHz, lebelo la tick la RTC le ka fetoloa ho lefella sena.
Ha u sebelisa TI-RTOS, RTC e sebelisoa e le nako ea motheo tsamaisong ea ts'ebetso 'me kahoo e lokela ho fumanoa feela ka li-API tsa kernel tse kang Clock module. Nako ea sebele ea nako e ka boela ea baloa ke Sensor Controller Engine ho ea ho linakoamp Sensor data hape e na le liteishene tse inehetseng tsa ho hapa. Ka ho sa feleng, RTC ea emisa ha debugger e emisa sesebelisoa.
Linako tse akaretsang tsa morero (GPTIMER)
Li-GPTIMER tse 'ne tse tenyetsehang li ka sebelisoa e le li-timers tsa 4 × 32 kapa 8 × 16 bit, kaofela li sebetsa ho fihla ho 48 MHz. E 'ngoe le e 'ngoe ea li-timers tsa 16- kapa 32-bit e tšehetsa mefuta e mengata ea likarolo tse kang ho thunngoa hanngoe kapa ho bala nako le nako, pulse width modulation (PWM), ho bala nako pakeng tsa mahlakore le ho bala ka bohale. Lintho tse kenang le tse hlahisoang ke nako li hokahane le lesela la ketsahalo ea sesebelisoa, e lumellang li-timers hore li sebelisane le matšoao a kang GPIO, li-timers tse ling, DMA le ADC. Li-GPTIMER li fumaneha ka mekhoa ea matla a Active le a Idle.
Li-Timer tsa Sensor Controller
Sensor Controller e na le li-timers tse 3:
AUX Timer 0 le 1 ke li-timers tsa 16-bit tse nang le prescaler tse peli. Li-timers li ka eketsa oache kapa pheletsong e 'ngoe le e 'ngoe ea mohloli o khethiloeng oa letshwao. Ho na le mefuta e 'ngoe ea nako ea ho thunya le ea nako le nako.
AUX Timer 2 ke sebali sa nako ea 16-bit se ka sebetsang ho 24 MHz, 2 MHz kapa 32 kHz ntle le ts'ebetso ea Sensor Controller. Ho na le liteishene tse 4 tsa ho hapa kapa ho bapisa, tse ka sebetsoang ka mokhoa o le mong kapa oa nako le nako. Nako e ka sebelisoa ho hlahisa liketsahalo bakeng sa Sensor Controller Engine kapa ADC, hammoho le tlhahiso ea PWM kapa tlhahiso ea waveform.
Radio Timer
Multichannel 32-bit timer e sebetsang ka 4 MHz e fumaneha e le karolo ea seea-le-moea sa sesebelisoa. Nako ea seea-le-moea hangata e sebelisoa e le setsi sa nako puisanong ea marang-rang e se nang mohala e sebelisang lentsoe la nako ea 32-bit joalo ka nako ea marang-rang. Nako ea seea-le-moea e hokahanngoa le RTC ka ho sebelisa radio API e khethehileng ha seea-le-moea sa sesebelisoa se buloa kapa se koetsoe. Sena se tiisa hore bakeng sa stack ea marang-rang, sebali-nako sa seea-le-moea se bonahala se sebetsa kamehla ha seea-le-moea se buletsoe. Nako ea seea-le-moea hangata e sebelisoa ka mokhoa o sa tobang ka nako ea nako ea trigger ho li-API tsa seea-le-moea 'me e lokela ho sebelisoa feela ha ho tsamaisoa kristale e nepahetseng ea 48 MHz high frequency ke mohloli oa SCLK_HF.
Nako ea balebeli
The watchdog timer e sebelisoa ho fumana taolo hape haeba sistimi e sebetsa ka phoso ka lebaka la liphoso tsa software. Hangata e sebelisoa ho hlahisa tšitiso le ho seta bocha sesebelisoa bakeng sa boemo boo ho lekoa nako le nako ha likarolo tsa sistimi le mesebetsi e hlolehang ho netefatsa ts'ebetso e nepahetseng. Sebali sa nako ea ho shebella se sebetsa ka sekhahla sa oache sa 1.5 MHz 'me se ke ke sa emisoa hang ha se bulela. Sebali sa nako se emisa ho sebetsa ka matla a Standby le ha sesebelisoa sa bothata se emisa sesebelisoa.

9.8 Serial Peripherals le I/O

Li-SSI ke likhokahano tsa serial tse lumellanang tse tsamaellanang le SPI, MICROWIRE, le TI's synchronous serial interfaces. Li-SSI li tšehetsa SPI master le makhoba ho fihlela 4 MHz. Li-module tsa SSI li tšehetsa karolo e ka lokisoang le polarity.
Li-UART li kenya tšebetsong mesebetsi ea bokahohleng ea asynchronous receiver le transmitter. Ba tšehetsa moloko o bonolo oa baudrate ho fihlela boholo ba 3 Mbps.
S e sebelisoa ho sebetsana le molumo oa dijithale mme e ka boela ea sebelisoa ho hokahanya maekrofono a pulse-density modulation (PDM).
The I 2 The IC interface e khona ho sebetsana le ts'ebetso ea 100 kHz le 400 kHz, 'me e ka sebetsa e le monghali le lekhoba.
C interface e boetse e sebelisetsoa ho buisana le lisebelisoa tse lumellanang le maemo a I 2 C. The I 2 The I/O controller (IOC) e laola li-pin tsa I/O tsa digital 'me e na le multiplexer circuitry ho lumella sete ea li-peripherals ho abeloa li-pin tsa I/O ka mokhoa o tenyetsehang. Li-I/O tsohle tsa dijithale li na le tšitiso ebile li khona ho tsoha, li na le ts'ebetso e hlophisehileng ea ho hula le ho theola, 'me li ka hlahisa tšitiso moeling o mobe kapa o motle (o ka lokisoang). Ha e hlophisitsoe joalo ka tlhahiso, likhoele li ka sebetsa joalo ka push-pull kapa open-drain. Li-GPIO tse hlano li na le bokhoni ba ho khanna ka mokhoa o phahameng, tse tšoailoeng ka sebete ho Karolo ea 7. Lisebelisoa tsohle tsa digital li ka kopanngoa le pini leha e le efe ea digital ho sesebelisoa.
Ho fumana lintlha tse ling, bona Buka ea CC13x2, CC26x2 SimpleLink™ Wireless MCU Technical Reference Manual.

9.9 Tekolo ea Betri le Mocheso
Mocheso o kopaneng le matla a betritage monitor e fumaneha sesebelisoa sa CC1312PSIP. Sesebelisoa sa betri le mocheso se lumella sesebelisoa hore se lule se lekola mocheso oa on-chip le ho fana ka voltage le ho arabela liphetohong tsa maemo a tikoloho ha ho hlokahala. Mojule o na le libapiso tsa lifensetere ho sitisa CPU ea sistimi ha mocheso kapa phepelo ea voltagke tsoela ka ntle ho lifensetere tse hlalositsoeng. Liketsahalo tsena li ka boela tsa sebelisoa ho tsosa sesebediswa ho tswa ho Boemo ba Standby ka lesela la ketsahalo la Always-On (AON).

9.10 µDMA
Sesebediswa se na le selaoli sa phihlello ya memori e otlolohileng (µDMA). Molaoli oa µDMA o fana ka mokhoa oa ho theola mesebetsi ea phetisetso ea data ho sistimi ea CPU, ka hona e lumella ts'ebeliso e ntle ea processor le bandwidth ea libese e fumanehang. Molaoli oa µDMA a ka etsa phetiso lipakeng tsa memori le li-peripheral. Molaoli oa µDMA o na le liteishene tse inehetseng bakeng sa mojule e 'ngoe le e' ngoe ea on-chip mme e ka hlophisoa hore e iketsetse phetiso lipakeng tsa peripherals le memori ha peripheral e se e loketse ho fetisa data e eketsehileng.
Likarolo tse ling tsa molaoli oa µDMA li kenyelletsa tse latelang (lena ha se lethathamo le felletseng):

Ts'ebetso ea liteishene tse feto-fetohang haholo le tse hlophisehang tsa liteishene tse fihlang ho tse 32
Mekhoa ea phetisetso: memori-ho-memori, memori-to-peripheral, peripheral-to-memory, le peripheral-to-peripheral
Boholo ba data ke 8, 16, le 32 bits
Mokhoa oa ping-pong bakeng sa ho phalla ha data khafetsa

9.11 Debug
Ts'ehetso ea on-chip debug e etsoa ka cJ e inehetsengTAG (IEEE 1149.7) kapa JTAG (IEEE 1149.1) sehokelo.
Sesebelisoa se qala ka ho iketsa cJTAG 'me e tlameha ho hlophisoa bocha ho sebelisa 4-pin JTAG.
9.12 Tsamaiso ea Matla
Ho fokotsa tšebeliso ea matla, CC1312PSIP e tšehetsa mekhoa e mengata ea matla le likarolo tsa tsamaiso ea matla (sheba Letlapa la 9-2).

Lethathamo la 9-2. Mekhoa ea Matla

MOKHOA	SOFTWARE MEKHOA EA TLHOKOMELO EA MATLA				RETS'ELISITSOE PIN TS'OA
MOKHOA	SEBELISA	IDLE	EMA HAUFI	KOALA	RETS'ELISITSOE PIN TS'OA
CPU	E sebetsa	E tima	E tima	E tima	E tima
Khanya	On	E fumaneha	E tima	E tima	E tima
SRAM	On	On	Ho boloka	E tima	E tima
Radio	E fumaneha	E fumaneha	E tima	E tima	E tima
Sistimi ea phepelo	On	On	Mosebetsi o Baesekele	E tima	E tima
Ngolisa le ho boloka CPU	E tletse	E tletse	Karolelano	Che	Che
Ho boloka SRAM	E tletse	E tletse	E tletse	Che	Che
48 MHz oache ea lebelo le phahameng (SCLK_HF)	XOSC_HF kapa RCOSC_HF	XOSC_HF kapa RCOSC_HF	E tima	E tima	E tima
2 MHz oache ea lebelo le mahareng (SCLK_MF)	RCOSC_MF	RCOSC_MF	E fumaneha	E tima	E tima
32 kHz oache ea lebelo le tlase (SCLK_LF)	XOSC_LF kapa RCOSC_LF	XOSC_LF kapa RCOSC_LF	XOSC_LF kapa RCOSC_LF	E tima	E tima
Pheripherals	E fumaneha	E fumaneha	E tima	E tima	E tima
Sensor Controller	E fumaneha	E fumaneha	E fumaneha	E tima	E tima
Tsoha ka RTC	E fumaneha	E fumaneha	E fumaneha	E tima	E tima
Tsoha ka lehlakoreng la pin	E fumaneha	E fumaneha	E fumaneha	E fumaneha	E tima
Tsoha ka phini ea reset	On	On	On	On	On
Bronout detector (BOD)	On	On	Mosebetsi o Baesekele	E tima	E tima
Ho seta bocha (POR)	On	On	On	E tima	E tima
Sebali sa nako (WDT)	E fumaneha	E fumaneha	E emisitsoe	E tima	E tima

Boemong bo sebetsang, sistimi ea ts'ebeliso ea CPU e ntse e sebelisa khoutu e sebetsang. Mokhoa o sebetsang o fana ka ts'ebetso e tloaelehileng ea processor le li-peripherals tse teng hajoale. Oache ea sistimi e ka ba mohloli ofe kapa ofe oa oache o fumanehang (sheba Letlapa la 9-2).
Ka mokhoa o sa sebetseng, lisebelisoa tsohle tse sebetsang li ka koaloa, empa konokono le memori ea Sesebelisoa sa CPU ha li ts'oaroe ebile ha ho khoutu e kentsoeng. Ketsahalo efe kapa efe ea tšitiso e khutlisetsa processor maemong a sebetsang.
Boemong ba Standby, ke sebaka se lulang se le teng feela (AON) se sebetsang. Ketsahalo ea kantle ea ho tsoha, ketsahalo ea RTC, kapa ketsahalo ea Sensor Controller ea hlokahala ho khutlisetsa sesebelisoa mokhoeng o sebetsang. Lisebelisoa tsa MCU tse bolokiloeng ha li hloke ho hlophisoa bocha ha li tsoha hape, 'me CPU e ntse e tsoela pele ho sebetsa ho tloha moo e ileng ea ea boemong ba standby. Li-GPIO kaofela li lokiselitsoe boemong ba standby.
Ka mokhoa oa ho koala, sesebelisoa se koetsoe ka ho feletseng (ho kenyeletsoa sebaka sa AON le Sensor Controller), 'me li-I / O li kenngoa ka boleng boo ba neng ba e-na le bona pele ba kena ka mokhoa oa ho koala. Phetoho ea boemo ho pini efe kapa efe ea I/O e hlalosoang e le ho tsoha ho tloha pineng ea ho koala e tsosa sesebelisoa mme e sebetsa joalo ka sehlomathiso. CPU e ka khetholla lipakeng tsa reset ka tsela ena le pin ea reset-by-reset kapa matla-on reset ka ho bala registara ea maemo a reset. Boemo bo le bong feela bo bolokiloeng mokhoeng ona ke boemo ba I/O le litaba tsa memori ea flash.

Sensor Controller ke processor e ikemetseng e ka laolang likarolo tse ho Sensor Controller ntle le sistimi ea CPU. Sena se bolela hore sistimi ea CPU ha ea tlameha ho tsoha, mohlalaample ho etsa ADC sampling kapa poll sensor ea dijithale holim'a SPI, ka hona ho boloka nako ea hajoale le ea ho tsoha e neng e ka senyeha. Sesebelisoa sa Sensor Controller Studio se nolofalletsa mosebelisi ho hlophisa Sensor Controller, ho laola likarolo tsa eona, le ho tsosa sistimi ea CPU ha ho hlokahala. Lisebelisoa tsohle tsa Sensor Controller le tsona li ka laoloa ke sistimi ea CPU.

Hlokomela
Matla, RF le taolo ea oache bakeng sa sesebelisoa sa CC1312PSIP e hloka tlhophiso e khethehileng le ts'ebetso ea software bakeng sa ts'ebetso e ntlafalitsoeng. Tlhophiso ena le ho sebetsana le eona li kenngoa ts'ebetsong ho li-drivers tse fanoeng ke TI tseo e leng karolo ea CC1312PSIP software development kit (SDK). Ka hona, TI e khothaletsa haholo ho sebelisa moralo oa software bakeng sa nts'etsopele eohle ea sesebelisoa sesebelisoa. SDK e felletseng e nang le TI-RTOS (boikhethelo), bakhanni ba lisebelisoa, le mohlalaampLes li fanoa mahala ho khoutu ea mohloli.
9.13 Litsamaiso tsa Oache
Sesebelisoa sa CC1312PSIP se na le lioache tse 'maloa tsa kahare tsa sistimi.
48 MHz SCLK_HF e sebelisoa e le oache ea mantlha (MCU le peripherals). Sena se ka tsamaisoa ke 48 MHz RC Oscillator (RCOSC_HF) kapa ka har'a sephutheloana sa 48 MHz crystal (XOSC_HF). Hlokomela hore ts'ebetso ea seea-le-moea e tima e kenyellelitsoeng, ka har'a kristale ea 48 MHz ka har'a mojule. Maqhubu a kristale a lekanyetsoa tlhahiso ka mocheso oa kamore ho fokotsa phoso ea pele ea maqhubu ho bonyane. Sena se etsoa ka ho beha sehlopha sa ka hare sa capacitor ho boleng bo fanang ka haufi le 48 MHz.
SCLK_LF ke 32.768 kHz oache ea ka hare ea maqhubu a tlase. E ka sebelisoa ke Sensor Controller bakeng sa ts'ebetso ea matla a tlase haholo 'me e boetse e sebelisetsoa RTC le ho hokahanya sebali sa radio pele kapa ka mor'a mokhoa oa matla oa Standby. SCLK_LF e ka khannoa ke 32.8 kHz RC Oscillator (RCOSC_LF) kapa e kenyelelitsoeng, ka har'a kristale ea 32.768 kHz ka har'a module.
Ha u sebelisa kristale kapa RC oscillator ea ka hare, sesebelisoa se ka ntša letšoao la 32 kHz SCLK_LF ho lisebelisoa tse ling, kahoo se fokotsa litšenyehelo tsa tsamaiso ka kakaretso.

9.14 Network Processor
Ho ipapisitsoe le tlhophiso ea sehlahisoa, sesebelisoa sa CC1312PSIP se ka sebetsa joalo ka processor ea netweke e se nang mohala (WNP - sesebelisoa se tsamaisang sephutheloana sa waelese se nang le sesebelisoa se sebetsang ho MCU ea moamoheli e arohaneng), kapa joalo ka sistimi-on-chip (SoC) e nang le sesebelisoa le protocol e sebetsang ho sistimi ea CPU kahare ho sesebelisoa.
Boemong ba pele, moamoheli oa kantle oa MCU o buisana le sesebelisoa a sebelisa SPI kapa UART. Boemong ba bobeli, kopo e tlameha ho ngoloa ho latela moralo oa kopo o fanoeng ka stack ea wireless protocol.

9.15 Setifikeiti sa Sesebelisoa le Boithuto
Mojule o tsoang ho TI o netefalitsoe bakeng sa FCC le IC/ISED. Bareki ba TI ba hahang lihlahisoa ho latela mojule oa TI ba ka boloka litšenyehelo tsa liteko le nako ka lelapa la sehlahisoa.

Hlokomela
Li-ID tsa FCC le IC li tlameha ho beoa bukeng ea mosebelisi le ka har'a sephutheloana. Ka lebaka la boholo bo fokolang ba mojule (7 mm x 7 mm), ho beha li-ID le matšoao ka mofuta oa boholo bo lekaneng hore bo balehe ntle le thuso ea ho hōlisa ha ho khonehe.

Lethathamo la 9-3. Lethathamo la Litifikeiti

Sehlopha sa Taolo	Tlhaloso	ID (HAEBA E SEBELISA)
FCC (USA)	15.247 Ts'ebetso ka har'a sehlopha sa 902–928 MHz	ZAT-1312PSIP-1
IC/ISED (Canada)	Ts'ebetso ea RSS-247 ka har'a sehlopha sa 902–928 MHz	451H-1312PSIP1
ETSI/CE (Europe) & RER (UK)	Sehlopha sa EN 300 220, 863 -870 MHz	–
	EN 303 204, 870–876 MHz sehlopha
	EN 303 659, 865-868 MHz le 915-919.4MHz

9.15.1 Setifikeiti le Setatamente sa FCC

TLHOKOMELO
Polelo ea Ts'oaetso ea Mahlaseli a FCC RF:
Sesebelisoa sena se lumellana le meeli ea ho pepeseha ha mahlaseli a FCC e behiloeng bakeng sa tikoloho e sa laoleheng. Basebelisi ba tlameha ho latela litaelo tse tobileng tsa ts'ebetso bakeng sa ho khotsofatsa meeli ea ho pepeseha ha RF. Transmitter ena ha ea lokela ho ba sebakeng se le seng kapa ho sebetsa le antenna kapa transmitter efe kapa efe.

Mojule oa CC1312PSIPMOT o tsoang ho TI o netefalitsoe bakeng sa FCC joalo ka transmitter e le 'ngoe. Mojule ke mojule oa seea-le-moea o tiisitsoeng ke FCC o nang le thuso ea modular.
U hlokomelisoa hore liphetoho kapa litokiso tse sa amoheloeng ka ho hlaka ke mokha o ikarabellang bakeng sa tsamaiso li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa.
Sesebelisoa sena se reretsoe ho latela Karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:

Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi.
Sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa.

9.15.2 Setifikeiti sa IC/IED le Setatamente

TLHOKOMELO
IC RF Radiation Exposure Statement:
E le ho ipapisa le litlhoko tsa ho pepeseha ha IC RF, sesebelisoa sena le lenakana la lona ha lia lokela ho behoa sebakeng se le seng kapa ho sebetsa mmoho le lenakana lefe kapa lefe kapa transmitter.
Mojule oa CC1312PSIPMOT o tsoang ho TI o netefalitsoe bakeng sa IC e le transmitter e le 'ngoe ea modular. Mojule oa CC1312PSIPMOT o tsoang ho TI o kopana le tumello ea modular ea IC le litlhoko tsa ho ngola. IC e latela liteko le melao e tšoanang le ea FCC mabapi le li-module tse netefalitsoeng ka thepa e lumelletsoeng.
Sesebelisoa sena se lumellana le litekanyetso tsa RSS tse sa lumelloeng ke laesense ea Industry Canada.
Ts'ebetso e ipapisitse le maemo a mabeli a latelang:

Sesebelisoa sena se kanna sa se ke sa baka tšitiso.
Sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa.

9.16 Matšoao a Mojule
Setšoantšo sa 9-1 se bontša letšoao le ka holimo-limo bakeng sa mojule oa CC1312PSIP.

Lethathamo la 9-4 le thathamisa matšoao a mojule oa CC1312PSIP.
Lethathamo la 9-4. Litlhaloso tsa Mojule

TŠOAOA	TLHALOSO
CC1312	Nomoro ea Karolo e Tloaelehileng
P	Mohlala
SIP	SIP = Mofuta oa mojule, X = tokollo pele
NNN NNNN	LTC (Lot Trace Code)

9.17 Qetella ho Ngola Sehlahisoa
Mojule oa CC1312PSIPMOT o lumellana le tumello ea FCC e le 'ngoe ea modular FCC, ID ea FCC: ZAT-1312PSIP-1.
Sistimi ea moamoheli e sebelisang mojule ona e tlameha ho hlahisa lengolo le hlahang le bontšang mongolo o latelang:
E na le FCC ID: ZAT-1312PSIP-1
Mojule oa CC1312PSIPMOT o lumellana le IC e le 'ngoe ea modular IC grant, IC: 451H-1312PSIP1. Sistimi ea moamoheli e sebelisang mojule ona e tlameha ho hlahisa lengolo le hlahang le bontšang mongolo o latelang:
E na le IC: 451H-1312PSIP1
Ho fumana lintlha tse ling mabapi le ho ngola sehlahisoa sa ho qetela le joalo kaample label, ka kopo bona karolo ea 4 ea Tataiso ea Bahokahanyi ba OEM
9.18 Boitsebiso ba Bukana ho Mosebelisi
Mohokahanyi oa OEM o tlameha ho hlokomela hore a se ke a fana ka tlhahisoleseling ho mosebelisi oa ho qetela mabapi le mokhoa oa ho kenya kapa ho tlosa mojule ona oa RF bukeng ea mosebelisi ea sehlahisoa sa pheletso e kopanyang mojule ona. Buka ea mosebelisi ea ho qetela e tlameha ho kenyelletsa lintlha tsohle tse hlokahalang tsa taolo le litemoso joalo ka ha ho bonts'itsoe bukeng ena.

Tshebediso, Phethahatso, le Moralo

Hlokomela
Lintlha tse karolong e latelang ea Likopo ha se karolo ea litlhaloso tsa karolo ea TI, 'me TI ha e fane ka bopaki ba ho nepahala kapa ho phethahala ha eona. Bareki ba TI ba na le boikarabello ba ho lekanya hore na likarolo li nepahetse molemong oa bona. Bareki ba lokela ho netefatsa le ho leka ts'ebetsong ea moralo oa bona ho netefatsa ts'ebetso ea sistimi.

10.1 Boitsebiso ba Kopo
10.1.1 Potoloho e Tloaelehileng ea Kopo
Setšoantšo sa 10-1 se bonts'a moralo o tloaelehileng oa kopo o sebelisang mojule oa CC1312PSIP. Bakeng sa moralo o felletseng oa litšupiso, khoasolla Moralo oa LP-EM-CC1312PSIP Files.
Hlokomela
Litaelo tse latelang li khothaletsoa bakeng sa ts'ebetsong ea moralo oa RF:

Netefatsa hore tsela ea RF e entsoe ka mokhoa o sa sebetseng oa 50 Ω.
Ho kgothaletswa ho lokisa marang-rang a antenna a impedans ka mor'a ho etsoa ha PCB ho ikarabella bakeng sa likokoana-hloko tsa PCB. Ka kopo, sheba CC13xx/CC26xx Hardware Configuration le PCB Design Menahano; karolo ea 5.1 bakeng sa lintlha tse ling.

Letlapa la 10-1 le fana ka bili ea thepa bakeng sa kopo e tloaelehileng e sebelisang module ea CC1312PSIP ho Setšoantšo sa 10-1.
Kamehla ho kgothaletswa ho kenya pi-filter (Z9, Z10 le Z11) pakeng tsa RF pad le antenna / SMA connector. Ha e bapisa lenaka, sena se tla fokotsa tahlehelo e sa tsamaisaneng ea lenakana. Ho ka khethoa marang-rang a maemo a tlase kapa marang-rang a holimo haholo.
Bakeng sa CC1312PSIP, ho khothaletsoa ho sebelisa papali ea antenna e tlase hobane sena ka bobeli se tla ts'oana le antenna empa hape se tla sebetsa joalo ka ts'ebetso ea filthara e tlase. Joalokaha ho ka bonoa ho Setšoantšo sa 10-1, Z10 le Z11 li theha papali ea li-antenna tse tlaase ho LP-EM-CC1312PSIP e nang le antenna e kopantsoeng ea PCB.
Haeba ho se na likarolo tse tsamaellanang tse hlokahalang bakeng sa antenna kapa khokahanyo e tobileng ho SMA, ho kgothaletswa ho sebelisa Z10: 5.6 nH le Z11: 1.8 pF e le filthara e tlaase.
Bakeng sa moralo o felletseng oa litšupiso, bona Moralo oa LP-EM-CC1312PSIP Files.
Lethathamo la 10-1. Bili ea Lintho

QTY	KAROLO SEBAKA	VALUE	MOEKETSI	KAROLO NUMBER	TLHALOSO
1	C57	100pF	Murata	Setšoantšo sa GRM0335C1H101GA01D	Capacitor, Ceramic C0G/NP0, 100pF, 50V, -2%/+2%, -55DEGC/+125DEGC, 0201, SMD
1	U1	Setšoantšo sa CC1312PSIP	Lisebelisoa tsa Texas	Setšoantšo sa CC1312PSIP	IC, CC1312PSIP, LGA73, SMD
1	Z10	8.2nH	Murata	LQP03TN8N2J02D	Inductor, RF, Chip, Non-magnetic core, 8.2nH, -5%/+5%, 0.25A, -55DEGC/ +125DEGC, 0201, SMD
1	Z11	1.8pF	Murata	GRM0335C1H1R8BA01J	Capacitor, Ceramic C0G/NP0, 1.8pF, 50V, -0.1pF/+0.1pF, -55DEGC/ +125DEGC, 0201, SMD

10.2 Khokahano ea Sesebelisuoa le Metheo ea Sebopeho
10.2.1 Seta bocha

E le hore u finyelle litlhoko tsa motlakase-on-reset ea module, VDDS (Pin 46) le VDDS_PU (Pin 47) li lokela ho hokahanngoa hammoho. Haeba lets'oao la ho seta botjha le sa itshetleha hodima matla a ho seta botjha mme ho e-na le hoo le nkilwe ho MCU e kantle, VDDS_PU (Pin 47) e lokela ho ba No Connect (NC).
10.2.2 Lithakhisa tse sa sebelisoeng
Lithako tsohle tse sa sebelisoeng li ka sala li sa kopanngoa ntle le ho tšoenyeha ka ho ba le leakage current. Ka kopo, sheba ho # e ikhethang_98 bakeng sa lintlha tse ling.

10.3 Litaelo tsa Moralo oa PCB
Karolo ena e qaqisa litataiso tsa PCB ho potlakisa moralo oa PCB ho sebelisa mojule oa CC1312PSIP. Mohokahanyi oa li-module o tlameha ho lumellana le likhothaletso tsa sebopeho sa PCB tse hlalositsoeng likotoana tse latelang ho fokotsa kotsi ka litifikeiti tsa taolo bakeng sa FCC, IC/ISED, ETSI/CE. Ho feta moo, TI e khothaletsa bareki ho latela litataiso tse hlalositsoeng karolong ena ho fihlela ts'ebetso e ts'oanang le e fumanoeng ka moralo oa litšupiso tsa TI.

10.3.1 Likhothaletso tsa Moralo ka Kakaretso
Etsa bonnete ba hore litlhahiso tse latelang tsa sebopeho se akaretsang lia lateloa:

E-ba le sefofane se tiileng sa fatše le li-vias tsa fatše tlas'a mojulu bakeng sa tsamaiso e tsitsitseng le ho senyeha ha mocheso.
Se ke oa tsamaisa mesaletsa ea mats'oao ka tlase ho mojule holim'a lera moo module e kentsoeng teng.

10.3.2 Litlhahiso tsa Moralo oa RF
Ho bohlokoa hore karolo ea RF e behoe ka nepo ho netefatsa ts'ebetso e nepahetseng ea module. Sebopeho se fosahetseng se ka baka matla a fokolang le ho senyeha ha maikutlo. Setšoantšo sa 10-2 se bonts'a ho beoa ha RF le ho tsamaisoa ha module ka 2.4-GHz e inverted F antenna.

Latela likhothaletso tsena tsa sebopeho sa RF bakeng sa mojule:

Mesaletsa ea RF e tlameha ho ba le ts'ebetso ea chararcterisitc ea 50-Ω.
Ha hoa tlameha ho ba le mesaletsa kapa fatše tlas'a karolo ea antenna.
Litsela tsa RF li tlameha ho ba le ka ho roka sefofaneng se fatše haufi le mohlala oa RF mahlakoreng ka bobeli.
Mesaletsa ea RF e tlameha ho ba e khuts'oane ka hohle kamoo ho ka khonehang.
Mojule o tlameha ho ba haufi le moeli oa PCB ha ho nahanoa kakarelo ea sehlahisoa le mofuta oa antenna e sebelisoang.

10.3.2.1 Ho beoa ha Antenna le Tsela
Antenna ke ntho e sebelisoang ho fetolela maqhubu a tataisoang ho PCB ho ea sebakeng sa mahala sa mahlaseli a motlakase. Ho beoa le ho beoa ha antenna ke linotlolo tsa ho eketseha ha mefuta le litefiso tsa data. Letlapa la 10-2 le fana ka kakaretso ea litataiso tsa li-antenna tse lokelang ho lateloa le CC1312PSIPmodule.

Lethathamo la 10-2. Tataiso ea Antenna

SR NO.	TATAISO
1	Beha lenakana ntlheng ea PCB.
2	Netefatsa hore ha ho mats'oao a tsamaisoang ho pholletsa le likarolo tsa manakana ho lera efe kapa efe ea PCB.
3	Bongata ba manakana, ho kenyeletsoa le lenakana la PCB le sebelisitsoeng ho LaunchPad™, li hloka tumello ea fatše holim'a likarolo tsohle tsa PCB. Netefatsa hore mobu o hloekisitsoe le holim'a mealo e ka hare.
4	Netefatsa hore ho na le tokisetso ea ho beha likarolo tse tsamaellanang tsa lenakana. Tsena li tlameha ho hlophisoa bakeng sa tahlehelo e ntle ka ho fetisisa ea ho khutlisa ha boto e felletseng e bokeletsoe. Lipolasetiki leha e le life kapa casing le tsona li tlameha ho kenngoa ha u ntse u lokisa antenna hobane sena se ka ama tšitiso.
5	Netefatsa hore sebopeho sa antenna ke 50-Ω kaha mojule o etselitsoe sistimi ea 50-Ω.
6	Haeba ho na le antenna e hatisitsoeng, etsa bonnete ba hore papiso e etsoa ho latela botenya ba soldermask.
7	Bakeng sa ts'ebetso e ntle ea RF e tiisa hore Voltge Standing Wave Ration (VSWR) e ka tlase ho 2 ho pholletsa le sehlopha sa maqhubu a thahasello.
9	Sebaka sa phepelo sa antenna sea hlokahala hore se thehoe. Sena ke sa mofuta oa manakana o sebelisitsoeng hoLP-EM-CC1312PSIP LaunPad™. Sheba maqephe a khethehileng a li-antenna bakeng sa likhothaletso.

Lethathamo la 10-3 le thathamisa manakana a khothaletsoang ho sebelisoa le CC1312PSIPmodule. Li-antenna tse ling li ka ba teng ho sebelisoa le CC1312PSIPmodule. Ka kopo sheba ho lenane la manakana a amohetsoeng (le mefuta ea manakana) a ka sebelisoang le mojule oa CC1312PSIP.
Lethathamo la 10-3. Li-Antenna tse khothalelitsoeng

MOKHETHI	ANTENA	MOEKETSI	LINTLHA TSEO
1	Antenna ea PCB e kopantsoeng ho LP-EM- CC1312PSIP	Lisebelisoa tsa Texas	+2.7 dBi phaello ho 915 MHz, bona moralo oa litšupiso oa LP-EM-CC1312PSIP
2	Lenaka la sephali sa kantle	Nearson, S463AM-915	+2.0 dBi phaello ho 915 MHz, https://www.nearson.com/assets/pdfs/Antenna/S463XX-915.pdf,
3	Lenaka la sephali sa kantle	Pulse, W5017	+0.9 dBi phaello ho 915 MHz
4	Chep antenna	Johanson Technology, 0900AT43A0070	-0.5 dBi phaello ho 915 MHz
5	Chep antenna	Johanson Technology, 0915AT43A0026	+1.4 dBi phaello ho 915 MHz
6	Antenna ea terata ea Helical	Pulse, W3113	+0.8 dBi phaello ho 915 MHz

10.3.2.2 Lintlha tsa Mohala oa Phetiso
Letšoao la RF le tsoang mojuleng le fetisetsoa ho antenna ho sebelisoa Coplanar Waveguide e nang le sebopeho sa fatše (CPW-G). Sebopeho sa CPW-G se fana ka palo e phahameng ka ho fetisisa ea ho itšehla thajana le tšireletso e ntle ka ho fetisisa mehala ea RF. Ho phaella fatše holim'a L1 lera, ho beha GND vias ka mola ho boetse ho fana ka tšireletso e eketsehileng.
Setšoantšo sa 10-3 se bontša karolo ea sefapano sa coplanar waveguide e nang le litekanyo tsa bohlokoa.
Setšoantšo sa 10-4 se bontša holimo view ea coplanar waveguide e nang le GND le ka ho roka.

Litekanyetso tse khothalelitsoeng bakeng sa boto ea PCB ea 4-layer li fanoe ho Lethathamo la 10-4.
Lethathamo la 10-4. Maemo a khothalelitsoeng a PCB bakeng sa 4-Layer
Boto (L1 ho L2 = 0.175 mm)

10.4 Meetso ea Litšupiso
Meralo e latelang ea litšupiso e lokela ho lateloa haufi-ufi ha ho etsoa meralo ka sesebelisoa sa CC1312PSIP.
Tlhokomelo e khethehileng e tlameha ho lefshoa ho beoa ha likarolo tsa RF, li-capacitor tse kopanyang le likarolo tsa taolo ea DCDC, hammoho le likhokahano tsa motheo bakeng sa tsena kaofela.

LP-EM-CC1312PSIP
Moralo Files

Moralo oa litšupiso oa LP-EM-CC1312PSIP o fana ka moralo, moralo le tlhahiso files bakeng sa boto ea litlhaku e sebelisitsoeng ho fumana nomoro ea ts'ebetso e fumanoang tokomaneng ena.

Sub-1 GHz le 2.4 GHz Antenna Kit bakeng sa
LaunchPad™ Development Kit le SensorTag

Sesebelisoa sa antenna se u lumella ho etsa liteko tsa 'nete ho tseba hore na antenna e nepahetse bakeng sa ts'ebeliso ea hau. Sesebelisoa sa antenna se kenyelletsa li-antenna tse 16 bakeng sa maqhubu ho tloha 169 MHz ho isa 2.4 GHz, ho kenyelletsa:
• Manakana a PCB
• Li-antenna tsa Helical
• Li-antenna tsa chip
• Li-antenna tsa Dual-band bakeng sa 868 MHz le 915 MHz hammoho le 2.4 GHz Setsi sa manakana se kenyelletsa thapo ea JSC ho hokela ho Wireless MCU LaunchPad Development Kits le Sensor.Tags.

Litlhoko tsa Tikoloho le Litlhaloso tsa SMT

11.1 PCB Ho Kobeha
PCB e latela IPC-A-600J bakeng sa PCB twist le warpage <0.75% kapa 7.5 mil ka inch.
11.2 Tšoaro ea Tikoloho
Li-terminals tse 11.2.1
Sehlahisoa se kentsoe ka boardboard ka Land-grid array (LGA). Ho thibela ho soasoa hampe, u se ke oa ikopanya le karolo ea LGA.
11.2.2 Ho oa
Likarolo tse behiloeng li tla senyeha haeba sehlahisoa se oa kapa se theoha. Tšenyo e joalo e ka etsa hore sehlahisoa se sebetse hantle.
11.3 Boemo ba polokelo
11.3.1 Mokotla o thibelang mongobo pele o buloa
Mokotla o thibelang mongobo o tlameha ho bolokoa mochesong o ka tlase ho 30°C ka mongobo o ka tlase ho 85% RH. Nako e baliloeng ea shelofo ea sehlahisoa se omeletseng e tla ba likhoeli tse 24 ho tloha ka letsatsi leo mokotla o tiisitsoeng ka lona.
11.3.2 Mokotla o thibelang mongobo oa Buloa
Likarete tse bontšang mongobo li tlameha ho ba le putsoa, <30%.
11.4 Tataiso ea Kopano ea PCB
Li-module tsa MCU tse se nang mohala li kentsoe ka har'a sephutheloana sa Leadless Quad Flatpack (QFM). Li-module li entsoe ka ho hula morao bakeng sa sebopeho se bonolo sa PCB le ho kenya boto.
11.4.1 PCB Land Pattern & Thermal Vias
Re khothalelitse mask a solder a hlalosang mokhoa oa mobu ho fana ka tekanyo e tsitsitseng ea solder pad e le ho fumana ho leka-lekana ha solder le ho ts'epahala ha motsoako oa solder. Paterone ea mobu ea PCB ke 1: 1 ho isa tekanyong ea li-module soldering pad. Thermal vias ka PCB amanang le tse ling tse tšepe sefofane morero oa ho qhala mocheso. Ho bohlokoa ho ba le li-vias tse lekaneng tsa mocheso ho qoba ho koala sesebelisoa sa mogote. Khothalletsoa vias boholo ba 0.2mm le boemo eseng ka ho toba tlas'a solder peista ho qoba solder rothele ka vias.
11.4.2 Likhothaletso tsa Kopano ea SMT
Ts'ebetso ea kopano ea "Module Mount Mount" e kenyelletsa:

Ho hatisa sekoahelo sa solder ho PCB
Lekola bophahamo ba molumo oa peista ea solder (ho tšoana)
Ho beha sephutheloana ho sebelisoa thepa e tloaelehileng ea ho beha SMT
Tlhahlobo ea X-ray pele ho phallo e ncha - ho peista borokho
Phallela hape
Tlhahlobo ea X-ray post-reflow - bridging ea solder le voids

11.4.3 PCB Surface Qetella Litlhokahalo
A junifomo PCB plating botenya ke senotlolo bakeng sa chai e ngata kopano. Bakeng sa ho qoelisoa ka khauta ea nickel e se nang motlakase, botenya ba khauta bo lokela ho tloha ho 0.05 µm ho isa ho 0.20 µm ho qoba ho kopana ha motsoako oa solder. Ho sebelisa PCB e nang le "Organic Solderability Preservative (OSP)" ho khothaletsoa joalo ka mokhoa o mong oa Ni-Au.

11.4.4 Stencil ea Solder
Solder peista deposition ho sebelisa stencil-printing process akarelletsa phetiso ea solder peista ka apertures predefined ka kopo ya khatello. Litekanyetso tsa li-stencil tse kang karo-karolelano ea sebaka sa aperture le mokhoa oa ho etsoa li na le tšusumetso e kholo ho peista peista. Ho hlahlojoa ha stencil pele ho behoa ha sephutheloana ho khothalletsoa haholo ho ntlafatsa lihlahisoa tsa kopano ea boto.
11.4.5 Ho bea Sephutheloana
Liphutheloana li ka behoa ho sebelisoa lisebelisoa tse tloaelehileng tsa ho khetha le ho beha ka nepo ea ± 0.05 mm. Sistimi ea ho khetha le ho beha libaka e entsoe ka sistimi ea pono e amohelang le ho beha karolo le sistimi ea mochini e etsang tšebetso ea ho khetha le ho beha sebaka. Mefuta e 'meli e sebelisoang hangata ea litsamaiso tsa pono ke:

Sistimi ea pono e fumanang silhouette ea sephutheloana
Sistimi ea pono e behang lipente tsa motho ka mong molemong oa khokahano

Mofuta oa bobeli o fana ka libaka tse nepahetseng haholoanyane empa o atisa ho bitsa chelete e ngata le ho ja nako. Mekhoa eo ka bobeli e amoheleha ho tloha ha likarolo li lumellana ka lebaka la ho iketsetsa likarolo tsa motsoako oa solder nakong ea ho phalla ha solder. E kgothaletswa ho qoba solder bridging ho 2 mils ka solder peista kapa ka bonyane matla a ho qoba ho baka tšenyo leha e le efe e ka bang teng ho thinner liphutheloana.
11.4.6 Tlhahlobo e Kopanetsoeng ea Solder
Ka mor'a kopano ea holim'a thaba, phetiso ea X-ray e lokela ho sebelisoa bakeng sa sample ho lekola ts'ebetso ea sehokelo sa solder. Sena se supa mefokolo joalo ka solder bridging, marikhoe a makgutshwane, opens, le voids. E boetse e kgothaletswa ho sebelisa lehlakoreng view tlhahlobo ho kenyelletsa X-rays ho fumana hore na ho na le solder e nang le sebopeho sa "Hour Glass" le sephutheloana se sekametseng. Sebopeho sa solder sa "Hour Glass" ha se motsoako o ka tšeptjoang. 90 ° seipone sa seipone se ka sebelisoa bakeng sa lehlakore view tlhahlobo.
11.4.7 Ho sebetsa bocha le ho Fetola
TI e khothaletsa ho tlosoa ha li-module ka seteishene sa rework ho sebelisa profile e ts'oanang le ts'ebetso ea ho kenya. Ho sebelisa sethunya sa mocheso ka linako tse ling ho ka baka tšenyo ea module ka ho chesa haholo.
11.4.8 Solder Joint Voiding
TI e khothaletsa ho laola voiding ea solder ho ba ka tlase ho 30% (ka IPC-7093). Li-voids tse kopantsoeng tsa solder li ka fokotsoa ka ho baka likarolo le PCB, nako e fokolang ea ho pepeseha ha solder, le reflow pro.file tokafatso.
11.5 Maemo a ho baka
Lihlahisoa li hloka ho baka pele li holisoa haeba:

Likarete tse bontšang mongobo li baloa > 30%
Mocheso o ka tlase ho 30°C, mongobo <70% RH, ho feta lihora tse 96
Boemo ba ho baka: 90 ° C, lihora tse 12 ho isa ho tse 24
Linako tsa ho baka: 1 nako

11.6 Boemo ba Soldering le Reflow Reflow

Mokhoa oa ho futhumatsa: Convection e tloaelehileng kapa IR convection
Tekanyo ea mocheso: Thermocouple d = 0.1 mm ho isa ho 0.2 mm CA (K) kapa CC (T) karolong ea soldering kapa mokhoa o lekanang
Sebopeho sa peista ea solder: SAC305
Linako tse lumelletsoeng tsa "reflow soldering": makhetlo a 2 ho ipapisitsoe le "reflow soldering pro".file (sheba setšoantšo sa 11-1)
Mocheso profile: Reflow soldering e tla etsoa ho latela mocheso oa profile (sheba setšoantšo sa 11-1)
Mocheso o phahameng: 260°CSetšoantšo sa 11-1. Mocheso Profile Bakeng sa Tlhahlobo ea ho hanyetsa mocheso oa Solder oa Karolo (ho Solder Joint)

Lethathamo la 11-1. Mocheso Profile

Profile Lintlha	Convection kapa IR(1)
Mocheso o phahameng oa mocheso	235 ho isa ho 240 ° C e tloaelehileng (260 ° C boholo)
Ho chesa pele / ho inela (150 ho 200 ° C)	Metsotsoana e 60 ho isa ho e 120
Nako e kaholimo ho sebaka se qhibilihang	Metsotsoana e 60 ho isa ho e 90
Nako le 5°C ho fihla sehlohlolong	30 metsotsoana boholo
Ramp up	<3°C / motsotsoana
Ramp fatshe	< -6°C / motsotsoana

(1) Bakeng sa lintlha, sheba tlhahiso ea moetsi oa pente ea solder.

Hlokomela
TI ha e khothaletse ts'ebeliso ea coat e hlophisitsoeng kapa lisebelisoa tse tšoanang ho module ea SimpleLink™.
Ho roala hona ho ka lebisa khatellong ea lehae mabapi le likhokahano tsa solder ka har'a mojulu le ho ama ts'epahalo ea mojule. E-ba hlokolosi nakong ea ts'ebetso ea kopano ea module ho PCB ea ho qetela ho qoba ho ba teng ha lintho tse tsoang linaheng tse ling ka har'a mojulu.

Tšehetso ea lisebelisoa le litokomane

TI e fana ka lethathamo le pharaletseng la lisebelisoa tsa ntlafatso. Lisebelisoa le software ea ho lekola ts'ebetso ea sesebelisoa, ho hlahisa khoutu, le ho hlahisa litharollo li thathamisitsoe ka tsela e latelang.

12.1 Nomenclament ea Sesebelisoa
Ho hlahisa stage le potolohong ea nts'etsopele ea sehlahisoa, TI e fana ka li-prefixes ho linomoro tsohle tsa likarolo le/kapa datecode.
Sesebelisoa se seng le se seng se na le e 'ngoe ea li-prefixes/litlhahiso tse tharo: X, P, kapa null (ha ho sehlomapele) (bakeng sa mohlala.ample, XCC1312PSIP e ka peleview; ka hona, sehlongoapele sa X se abetsoe).
Phallo ea ntlafatso ea sesebelisoa:
X Sesebediswa sa teko seo e seng se emelang dintlha tsa motlakase tsa ho qetela mme se kanna sa se sebedise phallo ya kopano ya tlhahiso.
Sesebediswa sa P Prototype seo ha se hakaalo hore silicon ya ho qetela e a shwa mme e ka nna ya se ke ya kopana le ditlhaloso tsa ho qetela tsa motlakase.
null tlhahiso ea tlhahiso ea silicon die e tšoanelehang ka botlalo.
Lisebelisoa tsa tlhahiso li 'nile tsa khetholloa ka botlalo,' me boleng le botšepehi ba sesebelisoa li bontšitsoe ka botlalo. Tiisetso e tloaelehileng ea TI ea sebetsa.
Likhakanyo li bontša hore lisebelisoa tsa prototype (X kapa P) li na le sekhahla se seholo sa ho hloleha ho feta lisebelisoa tse tloaelehileng tsa tlhahiso. Texas Instruments e khothaletsa hore lisebelisoa tsena li se sebelisoe tsamaisong efe kapa efe ea tlhahiso hobane sekhahla sa ho hloleha ha ts'ebeliso ea bona se lebelletsoeng se ntse se sa hlalosoa. Ho lokela ho sebelisoa lisebelisoa tse tšoanelehang feela tsa tlhahiso.
Nomenclature ea sesebelisoa sa TI e boetse e kenyelletsa sekoti se nang le lebitso la lelapa la sesebelisoa. Sehlomathiso sena se bontša mofuta oa sephutheloana (bakeng sa mohlalaample, RGZ).
Bakeng sa linomoro tse ka rekoang tsa lisebelisoa tsa CC1312PSIP mofuteng oa sephutheloana sa RGZ (7-mm x 7-mm), bona Sehlomathiso sa Khetho ea Pakete ea tokomane ena, Lintlha tsa Sesebelisoa Karolong ea 3, TI. websaete (www.ti.com), kapa ikopanye le moemeli oa hau oa thekiso oa TI.

12.2 Lisebelisoa le Software
Sesebelisoa sa CC1312PSIP se tšehetsoa ke mefuta e fapaneng ea lisebelisoa tsa ntlafatso ea software le hardware.
Ntlafatso Kit
Software

SimpleLink™ CC13xx le CC26xx Software

SimpleLink CC13xx-CC26xx Software Development Kit (SDK) e fana ka botlalo
sephutheloana sa nts'etsopele ea lits'ebetso tse se nang mohala ho lelapa la CC13x2 / CC26x2

Development Kit (SDK)

ea lisebelisoa. SDK e kenyelletsa sephutheloana sa software se felletseng bakeng sa sesebelisoa sa CC1312PSIP, ho kenyelletsa le mekotla e latelang ea protocol:
• Wi-SUN®
• TI 15.4-Stack – tharollo ea marang-rang ea linaleli e thehiloeng ho IEEE 802.15.4 bakeng sa Sub-1 GHz le 2.4 GHz
• Prop RF API - sete e feto-fetohang ea li-block tsa ho theha lisebelisoa tsa software tsa RF The SimpleLink CC13xx-CC26xx SDK ke karolo ea sethala sa TI's SimpleLink MCU, se fanang ka tikoloho e le 'ngoe ea nts'etsopele e fanang ka lisebelisoa tse feto-fetohang, software le lisebelisoa bakeng sa bareki ba ntlafatsang ka marang-rang le. lisebelisoa tse se nang mohala.
Ho fumana leseli le eketsehileng ka SimpleLink MCU Platform, etela https://www.ti.com/simplelink.

Lisebelisoa tsa Nts'etsopele

Moqapi oa Khoutu Studio™ Kopantsoeng Tsoelo-pele Tikoloho (IDE)	Code Composer Studio ke tikoloho e kopaneng ea nts'etsopele (IDE) e ts'ehetsang TI's Microcontroller le Embedded Processors portfolio. Code Composer Studio e na le lisebelisoa tse ngata tse sebelisoang ho theha le ho lokisa lits'ebetso tse kentsoeng. E kenyelletsa komporo e ntlafatsang ea C/C++, mohlophisi oa khoutu ea mohloli, tikoloho ea kaho ea projeke, debugger, profiler, le likarolo tse ling tse ngata. IDE e hlakileng e fana ka sebopeho se le seng sa mosebelisi se u tsamaisang mohatong o mong le o mong oa phallo ea nts'etsopele ea ts'ebeliso. Lisebelisoa tse tloaelehileng le li-interface li lumella basebelisi ho qala kapele ho feta leha e le neng pele. Code Composer Studio e kopanya advantages ea moralo oa software oa Eclipse® o nang le bokhoni bo tsoetseng pele ba ho lokisa bothata bo tsoang ho TI bo bakang tikoloho e tlamang ea ntlafatso e nang le likarolo tse ngata bakeng sa bahlahisi ba kentsoeng. CCS e na le ts'ehetso bakeng sa li-MCU tsohle tsa SimpleLink Wireless mme e kenyelletsa tšehetso bakeng sa software ea EnergyTrace™ (profiling ea tšebeliso ea matla a kopo). Ntho ea sebele ea nako viewer plugin ea fumaneha bakeng sa TI-RTOS, karolo ea SimpleLink SDK. Code Composer Studio e fanoa mahala ha e sebelisoa hammoho le li-debugger tsa XDS tse kenyellelitsoeng ho LaunchPad Development Kit.
Moqapi oa Khoutu Leru la Studio™ IDE	Code Composer Studio (CCS) Cloud ke a web-IDE e thehiloeng ho u lumella ho theha, ho hlophisa le ho aha merero ea CCS le Energia™. Kamora ho aha projeke ea hau ka katleho, o ka khoasolla le ho tsamaisa ho LaunchPad ea hau e hokahaneng. Debugging ea mantlha, ho kenyelletsa likarolo tse kang ho beha li-breakpoints le viewboleng bo fapaneng bo se bo tšehetsoa ke CCS Cloud.
IAR E kenyelelitsoe Sebaka sa mosebetsi® bakeng sa Letsoho®	IAR Embedded Workbench® ke sete sa lisebelisoa tsa nts'etsopele bakeng sa ho aha le ho lokisa lits'ebetso tsa sistimi e kentsoeng ho sebelisa assembler, C le C ++. E fana ka tikoloho ea ntlafatso e kopaneng ka botlalo e kenyelletsang mookameli oa projeke, mohlophisi, le lisebelisoa tsa ho aha. IAR e na le ts'ehetso bakeng sa li-MCU tsohle tsa SimpleLink Wireless. E fana ka tšehetso e pharalletseng ea debugger, ho kenyelletsa XDS110, IAR I-jet™ le Segger J-Link™. Ntho ea sebele ea nako viewer plugin ea fumaneha bakeng sa TI-RTOS, karolo ea SimpleLink SDK. IAR e boetse e tšehetsoa ka ntle ho lebokose ho li-software tse ngata tsa khaleamptse fanoeng e le karolo ea SimpleLink SDK. Tekolo ea matsatsi a 30 kapa mofuta o lekanyelitsoeng oa 32 KB o fumaneha ka iar.com.
SmartRF™ Setudio	SmartRF™ Studio ke sesebelisoa sa Windows® se ka sebelisoang ho lekola le ho hlophisa SimpleLink Wireless MCUs ho tsoa Texas Instruments. Ts'ebeliso e tla thusa baqapi ba litsamaiso tsa RF ho lekola seea-le-moea habonolo ka nako ea peletage ts'ebetsong ea moralo. E bohlokoa haholo bakeng sa ho hlahisa boleng ba rejisetara ea tlhophiso le litekong tse sebetsang le ho lokisa liphoso tsa sistimi ea RF. SmartRF Studio e ka sebelisoa e le sesebelisoa se ikemetseng kapa hammoho le liboto tse sebetsang tsa tlhahlobo kapa li-debug probes bakeng sa sesebelisoa sa RF. Likarolo tsa SmartRF Studio li kenyelletsa: • Hokela diteko – romela le ho amohela dipakete dipakeng tsa di-node

12.2.1 SimpleLink™ Microcontroller Platform
Sethala sa SimpleLink microcontroller se beha maemo a macha bakeng sa bahlahisi ba nang le potefolio e pharalletseng ea Arm e nang le wired le wireless.
Li-MCU (System-on-Chip) sebakeng se le seng sa ntlafatso ea software. E fana ka lisebelisoa tse feto-fetohang, software le likhetho tsa lisebelisoa bakeng sa lits'ebetso tsa hau tsa IoT. Tsetela hang ka har'a lisebelisoa tsa ntlafatso ea software ea SimpleLink 'me u e sebelise ho pholletsa le potefolio ea hau kaofela. Ithute haholoanyane ho ti.com/simplelink.

12.3 Tšehetso ea Litokomane

Ho fumana tsebiso ea lintlafatso tsa litokomane maqepheng a data, liphoso, lintlha tsa kopo le tse ling tse joalo, ea ho foldara ea sehlahisoa sa sesebelisoa ho ti.com/product/CC1312PSIP. K'honeng e kaholimo ho le letona, tlanya ho Ntlhokomelise ho ingolisa le ho amohela tšilo ea beke le beke ea tlhahisoleseling efe kapa efe e fetohileng. Bakeng sa lintlha tsa phetoho, review nalane ea ntlafatso e kenyellelitsoeng tokomaneng efe kapa efe e ntlafalitsoeng.
Litokomane tsa hajoale tse hlalosang MCU, li-peripherals tse amanang le tsona, le litšebeletso tse ling tsa tekheniki li thathamisitsoe ka tsela e latelang.

TI Resource Explorer
TI Resource Explorer
Software mohlalaamples, lilaebrari, executable, le litokomane li fumaneha bakeng sa sesebelisoa sa hau le boto ea nts'etsopele.

Phoso

Setšoantšo sa CC1312PSIP Phoso

The silicon errata e hlalosa mekhelo e tsebahalang ho litlhaloso tsa ts'ebetso bakeng sa ntlafatso e 'ngoe le e' ngoe ea silicon ea sesebelisoa le tlhaloso ea mokhoa oa ho lemoha tlhahlobo ea sesebelisoa.

Litlaleho tsa Kopo
Litlaleho tsohle tsa ts'ebeliso ea sesebelisoa sa CC1312PSIP li fumaneha foldareng ea sehlahisoa sa sesebelisoa ho: ti.com/product/CC1312PSIP/technicaldocuments.
Theknoloji ea Reference Manual (TRM)
CC13x2, CC26x2 SimpleLink™ Wireless MCU TRM

TRM e fana ka tlhaloso e qaqileng ea li-module tsohle le li-peripheral tse fumanehang lelapeng la lisebelisoa.

12.4 Lisebelisoa tsa Tšehetso
liforamo tsa tšehetso ke mohloli oa moenjiniere oa ho fumana likarabo tse potlakileng, tse netefalitsoeng le thuso ea moralo - ho tsoa ho litsebi ka kotloloho. Batla likarabo tse seng li ntse li le teng kapa u botse potso ea hau ho fumana thuso e potlakileng eo u e hlokang. ™ Likahare tse hokahantsoeng li fanoa JOALOKAHA ” ke batšehetsi ba fapaneng. Ha li hlahise litlhaloso tsa TI ebile ha li hlile ha li bontše li-TI views; sheba Melao ea Tšebeliso ea TI. 12.5 Matshwao a kgwebo ke matshwao a kgwebo a Texas Instruments. I-jet SimpleLink ™ , LaunchPad ™ , Code Composer Studio ™ , EnergyTrace ™ , le TI E2E ™ ke letšoao la khoebo la IAR Systems AB. J-Link ™ ke lets'oao la khoebo la SEGGER Microcontroller Systeme GmbH. Arm ™ ke matshwao a kgwebo a ngodisitsweng a Arm Limited (kapa makalana a yona) n US le/kapa kae kapa kae. CoreMark ® le Cortex ® tr ictio ns ke letshwao la kgwebo le ngodisitsweng la Embedded Microprocessor Benchmark Consortium Corporation. Arm Thumb ® ke lets'oao la khoebo le ngolisitsoeng la Arm Limited (kapa lithuso tsa eona). Eclipse ® ke lets'oao le ngolisitsoeng la Eclipse Foundation. IAR Embedded Workbench ® ke letšoao la khoebo le ngolisitsoeng la IAR Systems AB. Windows ® ke letšoao la khoebo le ngolisitsoeng la Microsoft Corporation. Matshwao ohle a kgwebo ke thepa ya beng ba ona. ®
12.6 Tlhokomeliso ea Phallo ea Motlakase

12.6 Tlhokomeliso ea Phallo ea Motlakase
Potoloho ena e kopaneng e ka senyeha ke ESD. Texas Instruments e khothaletsa hore lipotoloho tsohle tse kopaneng li tšoaroe ka litemoso tse nepahetseng. Ho se hlokomele mekhoa e nepahetseng ea ho sebetsana le ho kenya ho ka baka tšenyo.
Tšenyo ea ESD e ka tloha ho senyeha ho poteletseng ho isa ho ho hloleha ho felletseng ha sesebelisoa. Li-circuits tse kenyellelitsoeng ka nepo li kanna tsa senyeha habonolo hobane liphetoho tse nyane haholo tsa parametric li ka etsa hore sesebelisoa se se ke sa kopana le litlhaloso tsa sona tse hatisitsoeng.
12.7 Bukana ea mantsoe
Tlhaloso ea TI
Bukana ea boitsebiso e thathamisa le ho hlalosa mantsoe, mantsoe a khutsufalitsoeng le litlhaloso.

Tlhahisoleseding ea Mechini, ea ho Paka, le e Rekang

Maqephe a latelang a kenyelletsa liphutheloana tsa mochini le tlhaiso-leseling e ka hlophisoang. Lintlha tsena ke lintlha tsa morao-rao tse fumanehang bakeng sa lisebelisoa tse khethiloeng. Lintlha tsena li ka fetoha ntle le tsebiso le ntlafatso ea tokomane ena. Bakeng sa mefuta e thehiloeng ho sebatli ea leqephe lena la data, sheba mokhoa o ka letsohong le letšehali.
Hlokomela
Bophahamo bo felletseng ba mojule ke 1.51 mm.
Boima ba mojule oa CC1312PSIP hangata ke 0.19 g.

LINTLHA TSEO:

Litekanyo tsohle tsa mela li ka limilimithara. Likarolo life kapa life tse ka har'a masakana ke tsa litšupiso feela. Dimensioning le mamello ho ya ka ASME Y14.5M.
Setšoantšo sena se ka fetoha ntle le tsebiso.
EXAMPLE BOARD LAYOUT QFM – 1.51 mm max bophahamo
MOT0048A
Sephutheloana sena se etselitsoe ho rekisoa ho pad ea mocheso holim'a boto. Ho fumana lintlha tse ling, bona nomoro ea lingoliloeng tsa Texas Instruments SLUA271 (www.ti.com/lit/slua271).
Li-apertures tsa laser tse nang le marako a trapezoidal le likhutlo tse chitja li ka fana ka tokollo e ntle ea peista. IPC-7525 e kanna ea ba le likhothaletso tse ling tsa moralo.

TSEBISO LE BOHLOKOA

TI E FANA KA DATA YA MOSEBETSI OA TŠEBELETSO LE HO TŠEPAHALA (HO KAKARETSOA LE LIPAKENG TSA LITŠOANTŠISO), MESEBETSI EA HO HLAHALA (HO TSEBA LE MERARO EA TŠEBELETSO), KOPO KAPA KELETSO E MONG EA TLHALOSO, WEB LITHUTO, LITSEBISO TSA TŠEBELETSO, LE MESEBETSI E MONG “JALO KA HA E LE” LE KA LIPHOSO TSOHLE, LE E IKONELA LITIISETSO TSOHLE, TSE BOLELANG LE TSE BOLELANG, HO kenyeletsoa ntle le MOEDI LITIISETSO TSE FELENG TSA BORARO TSA THEKISO, HO LOKELA MOSEBETSI OA MOSEBETSI OA MOHOLO. LITHOELO LETLOTLO .
Lisebelisoa tsena li etselitsoe bahlahisi ba nang le litsebo ba ralang lihlahisoa tsa TI. U na le boikarabello ba ho (1) ho khetha lihlahisoa tse nepahetseng tsa TI bakeng sa kopo ea hau, (2) ho rala, ho netefatsa le ho hlahloba kopo ea hau, le (3) ho netefatsa hore kopo ea hau e finyella litekanyetso tse sebetsang, le tse ling tsa polokeho, tšireletso, taolo kapa litlhoko tse ling. .
Lisebelisoa tsena li ka fetoha ntle le tsebiso. TI e u fa tumello ea ho sebelisa lisebelisoa tsena molemong oa ntlafatso ea ts'ebeliso e sebelisang lihlahisoa tsa TI tse hlalositsoeng mohloding. Ho haneloa ka tlhahiso e 'ngoe le ho bonts'a lisebelisoa tsena. Ha ho laesense e fuoang tokelo efe kapa efe ea thepa ea mahlale ea TI kapa tokelo efe kapa efe ea thepa ea mahlale ea motho e mong. TI ha e na boikarabello bakeng sa, 'me u tla qosa TI le baemeli ba eona ka botlalo khahlanong le liqoso life kapa life, lits'enyehelo, litjeo, tahlehelo le mekoloto e bakoang ke ts'ebeliso ea hau ea lisebelisoa tsena.
Lihlahisoa tsa TI li fanoe ho latela Melao ea Thekiso ea TI kapa lipehelo tse ling tse sebetsang tse fumanehang ho ti.com kapa li fanoe mmoho le lihlahisoa tse joalo tsa TI. Tokisetso ea TI ea lisebelisoa tsena ha e atolohe kapa e fetola litiisetso tse sebetsang tsa TI kapa boithorollo ba tiisetso bakeng sa lihlahisoa tsa TI.
TI e hana le ho hana mantsoe afe kapa afe a tlatsetso kapa a fapaneng ao e ka 'nang eaba u a khothalelitse.
BOHLOKOA TSEBISO Aterese ea Lengolo: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated

Litokomane / Lisebelisoa

TEXAS INSTRUMENTS CC1312PSIP SimpleLink Sub-1-GHz Wireless System-in-Package [pdf] Buka ea Mong'a
CC1312PSIP SimpleLink Sub-1-GHz Wireless System-in-Package, CC1312PSIP, SimpleLink Sub-1-GHz Wireless System-in-Package, Sub-1-GHz Wireless System-in-Package, Wireless System-in-Package, System- ka har'a Pakete

Litšupiso

Bukana ea Mosebelisi

Likaroloana