I-Surenoo SLG320240B yoMzobo weModyuli ye-LCD yokubonisa iPhaneli yokuBonisa

UKU-odola ULWAZI

Inombolo yoku-oda

Umzekelo Hayi.	Bonisa	Ubungakanani	Ulwandlalo Ubungakanani (MM)	Viewnge Indawo (MM)	Indawo Indawo (MM)	Ujongano	Umqulutage	Umlawuli	UMKH	Umbala Iyasebenza	Umfanekiso
I-SLG320240B	320*240	5.7″	160.00*109.00	122.00*92.00	115.17*86.37	(20+8)P/2.54 8 Bit Parallel	5.0V	I-RA8835	Ukuxhathisa Chukumisa Iphaneli	SURENOO
										SURENOO

Umfanekiso

INGCACISO

Inkcazo yokubonisa

Ukucaciswa koomatshini

Ukucaciswa koMbane

Inkcazo ye-Optical

UMZOBI WAMAGAMA

I-SPEC YOMbane

Ukulungiselela uPinki

CN1 Pin Connections

CN2 Pin Connections

IiReyithingi eziphezulu ezipheleleyo

Iimpawu zoMbane ( VDD=5V±0.25V)

IBHODI YOMDLALO

INDLELA YOKUHLOLA

Inqanaba loMgangatho elamkelekileyo

Iqashiso ngalinye kufuneka lanelise umgangatho womgangatho ochazwe ngolu hlobo lulandelayo

Ukwahlulahlula	I-AQL	Ingcaciso
A. Major	0.4%	Ukungasebenzi kakuhle njengemveliso
B. Mncinane	1.5%	Yanelisa yonke imisebenzi njengemveliso kodwa ungonelisi umgangatho wokuthambisa

Ingcaciso yekaLote

Iqashiso elinye lithetha umyinge wokuhanjiswa kumthengi ngexesha elinye.

Umqathango woHlolo lwezithambiso

UKUHLOLWA KUNYE NOVAVANYO

• UVAVANYO LOMSEBENZI
• UKUHLOLWA KWENKQUBO
• INGCACISO YOKUPAKA

IMEKO YOKUHLOLA

• Beka phantsi kwe-lamp (20W) kumgama 100mm ukusuka
• Tikethe ngokuthe tye i-45 degree ngaphambili (ngasemva) ukuhlola inkangeleko yePaneli.

Inqanaba lokuHlola le-AQL

• • SAMPINDLELA YOKUPHILA: I-MIL-STD-105D
  • SAMPISICWANGCISO SOKUHLALA: ANGENYE
  • ISIFO ESIPHAMBILI: 0.4% (ENKULU)
  • ISIFO ESINCINANE: 1.5% (UMNCINCI)
  • INQANABA NGOKUBANZI: II/EQHELEKILEYO

Iikhrayitheriya zokuthambisa iModyuli

Hayi.	Into	Umgaqo wokugweba				Ukwahlulahlula
1	Umahluko kwi-Spec.	Akukho kuvunyelwayo				Enkulu
2	Ukukrolwa kwePatheni	Akukho pateni yesubstrate exobukayo kwaye iyadada				Enkulu
3	Iziphene zeSoldering	Akukho soldering engekho				Enkulu
		Akukho bhulorho yokuthambisa				Enkulu
		Akukho soldering ebandayo				Mncinci
4	Ukuxhathisa isiphene kwi-Substrate	Ifoyile yobhedu engabonakaliyo(￠0.5mm okanye ngaphezulu)kwipateni yesubstrate				Mncinci
5	Ukwandiswa kweMetallic Umba wangaphandle	Akukho luthuli lwe-soldering				Mncinci
		Akukho lunyuso lwemiba yesinyithi yangaphandle(Ayidluli ku-0.2mm)
6	Ibala	Akukho ibala ukonakalisa izithambiso kakubi				Mncinci
7	Ipleyiti Ukutshintsha umbala	Akukho pleyiti ibunayo, irusa kwaye ibe nombala				Mncinci
8	Ixabiso leSolder 1.Iinxalenye zeNkokheli	Icala lokuthengisa lePCB Solder ukwenza i'Filet'all around t I-Solder akufuneki ifihle ukukhokela Icala lamacandelo (Kwimeko 'ngeHole PCB') ISolder ukufikelela kwicala leMicimbi yePCB				Mncinci
	2.Flat Packages	Nayiphi na inzwana'(A) okanye 'impilo' (B) yesikhokelo ekufuneka igutyungelwe Filet' Ifom yokukhokelela ekuthathweni kwe-solder.				Mncinci
	3.Iitshiphusi	(3/2) H≧h≧(1/2)H				Mncinci

9	Iziphene zesibane	Ukukhanya kuyasilela okanye kuyadanyaza.(Enkulu) Umbala kunye nokukhanya akuhambelani neenkcukacha. (Okukhulu) Igqithise imigangatho yokubonisa amabala, into yangaphandle, imigca emnyama okanye imikrwelo.(Minor)	Jonga uluhlu ←
10	Iziphene zePCB	Usulelo okanye ungcoliseko kwizihlanganisi. Amalungu angalunganga, amalungu angekhoyo, okanye amalungu angacaciswanga. Izijumpi zisetwe ngokungalunganga.(Minor) I-Solder(ukuba ikhona) kwi-bezel, i-LED pad, i-zebra pad, okanye i-screw hole ipad ayigudi.(Encinci) Okuncinci ukuba bonisa imisebenzi ngokufanelekileyo. Okubalulekileyo ukuba umboniso uyasilela.	Jonga uluhlu ←
11	Iziphene zeSoldering	Intlama yesolder enganyibilikiyo. Amalungu abandayo e-solder, ukudityaniswa kwe-solder engekho, okanye i-oxidation. Iibhulorho zeSolder ezibangela iisekethe ezimfutshane. Intsalela okanye iibhola ze-solder. I-Solder flux imnyama okanye imdaka. Okuncinci ukuba bonisa imisebenzi ngokufanelekileyo. Okubalulekileyo ukuba umboniso uyasilela.	Mncinci

Iikhrayitheriya zokuthambisa zeSkrini (AziSebenziyo)

Hayi.	Isiphene	Umgwebo Ikhrayitheriya		Ukwahlulahlula
1	Amabala	Ngokuhambelana neScreen Cosmetic Criteria (Operating) No.1.		Mncinci
2	Imigca	Ngokuhambelana neScreen Cosmetic Criteria (Ukusebenza) No.2.		Mncinci
3	Amaqamza kwiPolarizer			Mncinci
		Ubukhulu: d mm	I-Qty eyamkelekileyo kwindawo esebenzayo
		d≦0.3 0.3 1.0 1.5<d	Ukungahoyi 3 1 0
4	Ukukrwela	Ngokungqinelana namabala kunye nemigca yokusebenza iikhrayitheriya zokuthambisa, Xa ukukhanya ibonakalisa kumphezulu wendawo yolawulo, imikrwelo ayifanelanga iphawuleke.		Mncinci
5	Ubuninzi obuvumelekileyo	Iziphene ezingentla kufuneka zohlulwe ngaphezu kwe-30mm enye kwenye.		Mncinci
6	Umbala	Ayinakuba nombala obonakalayo kwi viewindawo yeephaneli zeGraphic. Uhlobo olukhanyiswe ngasemva kufuneka lugwetywe ngokulayita ngasemva kwimeko kuphela.		Mncinci
7	Usulelo	Ayinakuphawuleka.		Mncinci

Iikhrayitheriya zokuthambisa zeSkrini (Ezisebenzayo)

Hayi.	Isiphene	Umgwebo Ikhrayitheriya		Ukwahlulahlula
1	Amabala	A) Kucacile		Mncinci
		Ubukhulu:d mm	I-Qty eyamkelekileyo kwindawo esebenzayo
		d≦0.1 0.1 0.2 0.3<d	Ukungahoyi 6 2 0
		Qaphela: Kubandakanya imingxunya ekhonkwane kunye namachaphaza anesiphene ekufuneka abe ngaphakathi kwePixel enye. Ayicacanga
		Ubukhulu:d mm	I-Qty eyamkelekileyo kwindawo esebenzayo
		d≦0.2 0.2 0.5 0.7<d	Ukungahoyi 6 2 0
2	Imigca	A) Kucacile   Phawula: () – Ubungakanani obamkelekileyo kwindawo esebenzayo L – Ubude (mm) W -Ububanzi(mm) ∞-Ukungahoyi B) Ayicacanga		Mncinci
Sula' = Umthunzi kunye nobukhulu azitshintshwa nguVo. Ayicacanga'= Umthunzi kunye nobukhulu zitshintshwa nguVo.

Hayi.	Isiphene	Umgwebo Ikhrayitheriya	Ukwahlulahlula
3	Umgca wokuhlikihla	Ayinakuphawuleka.	Mncinci
4	Ubuninzi obuvumelekileyo	Iziphene ezingentla kufuneka zohlulwe ngaphezu kwe-10mm enye kwenye.	Mncinci
5	Umnyama	Ayinakuphawuleka.	Mncinci
6	Ubungakanani bechaphaza	Ukuba yi-95% ~ 105% yobungakanani bechaphaza (Uhlobo.) kumzobo. Iziphene ezithile zechaphaza ngalinye (ex.pin-hole) kufuneka ziphathwe njengebala. (jonga iScreen Cosmetic Criteria (Operating) No.1)	Mncinci
7	Ukukhanya (kuphela imodyuli ekhanyiswe ngasemva)	Ukukhanya okufanayo kufuneka kube yi-BMAX/BMIN≦2 BMAX: Max.value ngomlinganiselo ngamanqaku ama-5 BMIN: Min. ixabiso ngomlinganiselo kumanqaku ama-5 Yahlula indawo esebenzayo ibe yi-4 ngokuthe nkqo nangokuthe tye. Linganisa amanqaku ama-5 aboniswe kulo mfanekiso ulandelayo.	Mncinci
8	Ukuthelekisa ukufana	I-Contrast Uniformity kufuneka ibe yi-BmAX/BMIN≦2 Linganisa amanqaku ama-5 aboniswe kulo mfanekiso ulandelayo. Imigca edawuniweyo yahlula indawo esebenzayo ibe yi-4 ngokuthe nkqo nangokuthe tye. Amanqaku okulinganisa afumaneka kumacandelo adibeneyo omgca odayishiweyo. Phawula: BMAX - Max.value ngomlinganiselo kumanqaku ama-5. BMIN – Min.value by measure in 5 points. O – Amanqaku okulinganisa kwi-￠10mm.	Mncinci
Phawula Ubungakanani: d=(ubude obude + ubude obufutshane)/2 Umda sampinto nganye ibalulekile. Iziphene ezintsonkothileyo zichazwa into ngenqaku, kodwa ukuba inani leziphene lichazwe kwitheyibhile engentla, inani elipheleleyo alifanele lidlule kwi-10.

Ukhuseleko lokuSebenza

• MUSA iplagi okanye ukhuphe imodyuli yeSurenoo xa isixokelelwano sixhotyiswa phezulu.
• Nciphisa ubude bentambo phakathi kwemodyuli ye-Surenoo kunye ne-MPU yokusingatha.
• Kwiimodeli ezinezibane zangasemva, musa ukuvala isibane sangasemva ngokuphazamisa umgca we-HV. Ukukhulula ii-inverters zivelisa umthamotagUgqithiso olunokubakho ngaphakathi kwentambo okanye kwisibonisi.
• Sebenzisa imodyuli ye-Surenoo ngaphakathi kwemida yeemodyuli zemilinganiselo yobushushu.

Oomatshini/amanyathelo okuCwatha kokuSingqongileyo

• I-solder engafanelekanga ngoyena nobangela wobunzima bemodyuli. Ukusetyenziswa kwesicoci se-flux akukhuthazwa njengoko banokungena phantsi koqhagamshelwano lwe-electrometric kwaye kubangele ukusilela kokubonisa.
• INtaba yeSurenoomodule ukuze ikhululeke kwi-torque kunye noxinzelelo lomatshini.
• Umphezulu wephaneli yeGraphic akufuneki uchukunyiswe okanye ukrwelwe. Umphezulu obonisa umphezulu yinto ekrwela ngokulula, iplastiki yepolarizer. Kulumkele ukudibana kwaye ucoce kuphela xa kuyimfuneko ngomqhaphu othambileyo, ofunxayo dampeyenziwe ngepetroleum benzene.
• Ngalo lonke ixesha sebenzisa inkqubo ye-anti-static ngelixa uphethe imodyuli yeSurenoo.
• Thintela ukwakheka kokufuma kwimodyuli kwaye ujonge imiqobo yokusingqongileyo ukulungiselela ixesha lokugcina
• Musa ukugcina elangeni elithe ngqo
• Ukuba ukuvuza kwezinto ze-crystal ye-liquid kufuneka kwenzeke, gwema ukudibanisa nale nto, ngakumbi ukungeniswa. Ukuba umzimba okanye impahla iye yangcoliswa yikristale elulwelo, hlamba ngocoselelo ngamanzi nangesepha.

ImiGaqo yokuGcina

Xa ugcina iimodyuli zeGraphic, kunqanda ukuchanabeka kwilanga elithe ngqo okanye ukukhanya kwefluorescent l.amps. Gcina iimodyuli ze-Surenoo kwiingxowa (ugweme ukushisa okuphezulu / ukufuma okuphezulu kunye namaqondo aphantsi angaphantsi kwe-0 ºC. Nanini na xa kunokwenzeka, iimodyuli ze-Surenoo G raphic kufuneka zigcinwe kwiimeko ezifanayo apho zithunyelwe khona kwinkampani yethu.

Abanye

Iikristale zolwelo ziqina phantsi kobushushu obuphantsi (ngaphantsi koluhlu lwamaqondo obushushu okugcinwa kuzo) ezikhokelela kwi-orientation enesiphako okanye ukuveliswa kwamaqamza omoya (amnyama okanye amhlophe). Amaqamza omoya nawo anokwenziwa ukuba imodyuli iphantsi kobushushu obuphantsi. Ukuba iimodyuli zeSurenoo Graphic bezisebenza ixesha elide zibonisa iipatheni ezifanayo zokubonisa, iipatheni zokubonisa zinokuhlala kwiscreen njengemifanekiso yesiporho kunye nokungafani okuncinci kokungafaniyo kunokuvela. Ubume obuqhelekileyo bokusebenza bunokufunyanwa kwakhona ngokumisa ukusetyenziswa ixesha elithile. Kufuneka kuqatshelwe ukuba le nto ayichaphazeli kakubi ukuthembeka komsebenzi. Ukunciphisa ukuthotywa kokusebenza kweemodyuli ze-Graphic ezibangelwa ukutshatyalaliswa okubangelwa ngumbane osisigxina njl., sebenzisa unonophelo ukuphepha ukubamba amacandelo alandelayo xa ubamba iimodyuli.

• Indawo eveziweyo yebhodi yesekethe eprintiweyo.
• Amacandelo e-terminal electrode.

Kwimeko 'yoxinaniso', kwanamabala okanye imigca 'engahoywanga' ubukhulu mayingavunyelwa. Ukulandela iimeko ezintathu kufuneka kuthathwe 'njengogxininiso'.

• 7 okanye ngaphezulu kweziphene kwisangqa se ￠5mm.
• I-10 okanye ngaphezulu kweziphene kwisangqa se-￠10mm
• I-20 okanye ngaphezulu kweziphene kwisangqa se-￠20mm

IMIGAQO YOKUSEBENZISA

Ukuphatha imiGaqo

• Esi sixhobo sisesichengeni sokonakala kwe-Electro-Static Discharge (ESD). Qaphela izilumkiso ze-Anti-Static.
• Iphaneli yokubonisa yeSurenoo yenziwe ngeglasi. Musa ukuwubeka phantsi komothuko womatshini ngokuwuwisa okanye impembelelo.
• Ukuba iphaneli yokubonisa yeSurenoo yonakele kwaye into eyikristale engamanzi iyavuza, qiniseka ukuba awufumani nanye emlonyeni wakho. Ukuba loo nto idibana nesikhumba okanye iimpahla zakho, zihlambe usebenzisa isepha namanzi.
• Musa ukusebenzisa amandla agqithisileyo kumphezulu wokubonisa weSurenoo okanye iindawo ezidityanisiweyo kuba oku kunokubangela ithowuni yombala yahluke.
• I-polarizer egquma umphezulu we-Surenoo wokubonisa imodyuli ye-Graphic ithambile kwaye ikrwela ngokulula. Phatha le polarizer ngononophelo.
• Ukuba indawo ebonisa i-Surenoo iye yangcoliseka, phefumlela ngaphezulu kwaye wosule ngobunono ngelaphu elomileyo elithambileyo. Ukuba ingcoliseke kakhulu, thambisa ilaphu ngenye yezi zilandelayo Isopropyl okanye utywala.
• Izinyibilikisi ngaphandle kwezi zikhankanywe apha ngasentla zisenokonakalisa i-polarizer. Ngokukodwa, musa ukusebenzisa Amanzi.
• Zilolonge ngononophelo ukunciphisa ukubola kwe-electrode. I-Corrosion ye-electrodes ikhawuleza ngamaconsi amanzi, ukunyuswa komswakama okanye ukuhamba kwangoku kwindawo yomswakama ophezulu.
• Faka iModyuli yeSurenoo G raphic ngokusebenzisa imingxunya enyukayo. Xa unyusela imodyuli yoMzobo qiniseka ukuba isimahla ekujikeni, ukujika nokugqwesa. Ngokukodwa, musa ukutsala ngenkani okanye ukugoba intambo okanye ikhebula le-backlight.
• Ungazami ukuqhawula okanye ukuqhubela phambili imodyuli ye-Surenoo G raphic.
• Itheminali ye-NC kufuneka ivulwe. Musa ukudibanisa nantoni na.
• Ukuba amandla esekethe yengqiqo acinyiwe, musa ukusebenzisa imiqondiso yokufaka.
• Ukuthintela ukutshatyalaliswa kwezinto ngombane we-static, qaphela ukugcina indawo yokusebenza efanelekileyo.
  • Qiniseka ukuba uyawuthoba umzimba xa uphethe iimodyuli zeSurenoo Graphic.
  • Izixhobo ezifunekayo ekuhlanganiseni, ezifana neentsimbi ze-soldering, kufuneka zibekwe ngokufanelekileyo.
  • Ukunciphisa inani lombane omileyo owenziweyo, musa ukuqhuba ukudibanisa kunye nomnye umsebenzi phantsi kweemeko ezomileyo.
  • Imodyuli yeGraphic ifakwe ifilimu ukukhusela umphezulu wokubonisa. Ziqeqeshe ngononophelo xa ukhupha le filimu ekhuselayo kuba umbane ongatshintshiyo unokuveliswa.

Ubonelelo ngoMbane

• Chonga kwaye, ngawo onke amaxesha, jonga amanqaku aphezulu kuwo omabini abaqhubi be-logic kunye ne-LC. Qaphela ukuba kukho umahluko phakathi kweemodeli.
• Thintela ukusetyenziswa kwe-polarity ebuyela umva kwi-VDD kunye ne-VSS, nangona kunjalo ngokufutshane.
• Sebenzisa umthombo wamandla ococekileyo ongenaziphene. Iimeko zokunyusa amandla ngamanye amaxesha ziyashukuma kwaye zinokugqitha kumazinga aphezulu eemodyuli zeSurenoo.
• Amandla e-VDD emodyuli ye-Surenoo kufuneka anike amandla kuzo zonke izixhobo ezinokufikelela kwisiboniso. Musa ukuvumela ibhasi yedatha ukuba iqhutywe xa unikezelo lwengqiqo kwimodyuli lucinyiwe.

UKUSEBENZISA IIMODULI zeMizobo

Iimodyuli zokuBonisa iCrystal elulwelo

• I-Surenoo Display yenziwe ngeglasi kunye ne-polarizer. Nika ingqalelo kwezi zinto zilandelayo xa uphethe.
• Nceda gcina iqondo lobushushu phakathi koluhlu oluchaziweyo lokusebenzisa kunye nokugcinwa. Ukuthotywa kwepolarization, ukuveliswa kwamaqamza okanye i-polarizer peel-off ingenzeka ngobushushu obuphezulu kunye nokufuma okuphezulu.
• Ungachukumisi, utyhale okanye uhlikihle i-polarizers eveziweyo ngayo nantoni na enzima kunelothe yepensile ye-HB (iglasi, i-tweezers, njl.).
• I-N-hexane icetyiswa ngokucoca i-adhesives esetyenziselwa ukufaka i-polarizers yangaphambili / yangasemva kunye ne-reflectors eyenziwe ngezinto eziphilayo eziza konakaliswa ziikhemikhali ezifana ne-acetone, i-toluene, i-ethanol kunye ne-isopropyl alcohol.
• Xa umphandle we-Surenoo uba nothuli, sula ngobunono ngomqhaphu ofunxayo okanye enye imathiriyeli ethambileyo efana ne-chamois efakwe kwi-petroleum benzin. Sukukhuhla ngamandla ukunqanda ukonakalisa umphezulu wokubonisa.
• Sula amathe okanye amathontsi amanzi ngoko nangoko, ukudibana namanzi ixesha elide kunokubangela ukonakala okanye ukunyamalala kombala.
• Kuphephe ukudibana neoli kunye namafutha.
• Ukuxinana kumphezulu kunye nokunxibelelana neetheminali ngenxa yokubanda kuya konakalisa, kungcolise okanye kungcolise iipolarizers. Emva kokuba iimveliso zivavanyiwe kubushushu obuphantsi kufuneka zifudunyezwe kwisikhongozeli phambi kokuba zifike kukudibana nomoya wobushushu begumbi.
• Ungabeki okanye uncamathisele nantoni na kwindawo yokubonisa iSurenoo ukunqanda ukushiya amanqaku evuliwe.
• Musa ukubamba isibonisi ngezandla ezingenanto. Oku kuya kungcolisa indawo yokubonisa kunye nokwehliswa kwe-insulation phakathi kwee-terminals (ezinye izinto zokuthambisa zimiselwe kwii-polarizers).
• Njengoko iglasi ibuthathaka. Ithande ukuba okanye itshiphuke ngexesha lokuphatha ingakumbi emaphethelweni. Nceda uphephe ukuwa.

Ukufakela iiModyuli zoMzobo

• Gubungela umphezulu ngepleyiti yokukhusela ecacileyo ukukhusela i-polarizer kunye ne-LC cell.
• Xa uhlanganisa i-LCM kwezinye izixhobo, i-spacer kwi-bit phakathi kwe-LCM kunye neplate efanelekileyo kufuneka ibe nokuphakama okwaneleyo ukuphepha ukubangela uxinzelelo kumphezulu wemodyuli, bhekisa kwiinkcukacha zomntu ngamnye kwimilinganiselo. Ukunyamezela komlinganiselo kufuneka kube ±0.1mm.

Isilumkiso sokuphatha iiModyuli zeGraphic

Ekubeni i-Surenoo LCM iye yahlanganiswa kwaye yalungiswa ngezinga eliphezulu lokuchaneka; Kuphephe ukusebenzisa izothuso ezigqithisileyo kwimodyuli okanye ukwenza naluphi na utshintsho okanye uhlengahlengiso kuyo.

• Musa ukuguqula, ukuguqula okanye ukutshintsha imilo yethebhu kwisakhelo sesinyithi.
• Musa ukwenza imingxuma eyongezelelweyo kwibhodi yesekethe eprintiweyo, uguqule imilo yayo okanye utshintshe izikhundla zamacandelo ukuba aqhotyoshelwe.
• Musa ukonakalisa okanye ukuguqula indlela yokubhala kwibhodi yesekethe eprintiweyo.
• Ngokuqinisekileyo musa ukuguqula umcu werabha weqwarhashe (irabha eqhubayo) okanye isidibanisi setywina lobushushu.
• Ngaphandle kwe-soldering i-interface, musa ukwenza naluphi na utshintsho okanye ukuguqulwa ngentsimbi ye-soldering.
• Musa ukuyiwisa, ukugoba okanye ukujija iSurenoo LCM.

I-Electro-Static Discharge Control

Kuba le modyuli isebenzisa i-CMOS LSI, kufuneka kuqwalaselwe ingqalelo efanayo kwi-electrostatic discharge njenge-CMOS IC eqhelekileyo.

• Qinisekisa ukuba uphantsi xa unikezela ngeLCM.
• Ngaphambi kokuba ususe i-LCM kwipakethi yayo yokupakisha okanye uyifake kwiseti, qiniseka ukuba imodyuli kunye nomzimba wakho unamandla afanayo ombane.
• Xa uthengisa i-terminal ye-LCM, qiniseka ukuba umthombo wamandla we-AC we-iron ye-solder awuvuzi.
• Xa usebenzisa isikrudrayiva sombane ukuncamathisela i-LCM, isikrudrayiva kufuneka sibe namandla asemhlabeni ukunciphisa kangangoko kunokwenzeka naluphi na usasazo lwamaza ombane ovelisa iintlantsi ezivela kwisihambisi senjini.
• Kangangoko kunokwenzeka ukwenza amandla ombane weempahla zakho zokusebenza kunye nebhentshi yomsebenzi amandla omhlaba.
• Ukunciphisa ukuveliswa kombane omileyo qaphela ukuba umoya osemsebenzini awungomiswa kakhulu. Kucetyiswa ukufuma okumalunga ne-50% -60%.

Isilumkiso sokuthengisa kwi-Surenoo LCM

• Qwalasela oku kulandelayo xa i-soldering wire lead, intambo yesidibanisi kunye njl njl kwi-LCM.
  • Ubushushu bentsimbi yokujongisa: 280℃±10℃
  • Ixesha lokuthengisa: 3-4 umzuzwana.
  • Isolder: solder eutectic.

Ukuba i-soldering flux isetyenzisiwe, qiniseka ukuba uyayisusa nayiphi na i-flux eseleyo emva kokugqiba ukusebenza kwe-soldering. (Oku akusebenzi kwimeko yohlobo lwe-non-halogen lwe-flux.) Kucetyiswa ukuba ukhusele umphezulu wePanel kunye nesigqubuthelo ngexesha le-soldering ukukhusela nawuphi na umonakalo ngenxa ye-spatters ye-flux.

• Xa i-soldering panel ye-electroluminescent kunye nebhodi ye-PC, ipaneli kunye nebhodi akufanele zikhutshwe ngaphezu kwamaxesha amathathu. Eli nani liphezulu lichongwa bubushushu kunye neemeko zexesha ezikhankanywe ngasentla, nangona kunokubakho ukuhluka ngokuxhomekeke kubushushu bentsimbi yokuthambisa.
• Xa ususa iphaneli ye-electroluminescent kwibhodi yePC, qiniseka ukuba i-solder inyibilike ngokupheleleyo, iphedi ethengiswayo kwibhodi yeePC inokonakala.

Umqathango wokuSebenza

• Ukuqhuba iSurenoo Graphic kwivoltage ngaphezulu komda yenza bufutshane ubomi bayo.
• Ixesha lokuphendula libambezeleke kakhulu kwiqondo lokushisa elingaphantsi kweqondo lokushisa lokusebenza. Nangona kunjalo, oku akuthethi ukuba iPhaneli iya kuba ngaphandle kocwangco. Iya kuphola xa ibuyela kuluhlu lobushushu obuchaziweyo.
• Ukuba umboniso weSurenoo utyhalwa ngamandla ngexesha lokusebenza, isiboniso siya kuba singaqhelekanga. Nangona kunjalo, iya kubuyela kwimeko yesiqhelo ukuba icinyiwe kwaye iphinde ivule.
• Ukuxinana kwii-terminals kunokubangela ukuba i-electrochemical reaction iphazamise i-terminal circuit. Ngoko ke, kufuneka isetyenziswe phantsi kwemeko enxulumene ne-40 ℃, 50% RH.
• Xa uvula umbane, faka umqondiso ngamnye emva kwevolthi elungileyo/engalungangatage uzinzile.

Iwaranti enyiniweyo

Ngaphandle kokuba kuvunyelwene phakathi kwe-Surenoo kunye nomthengi, i-Surenoo iya kuthatha indawo okanye ilungise nayiphi na imodyuli yayo ye-Graphic efunyenwe ingasebenzi kakuhle xa ihlolwe ngokuhambelana nemigangatho yokwamkelwa kwe-Surenoo G (iikopi ezikhoyo xa ziceliwe) kwisithuba sonyaka omnye ukususela kumhla wokuthunyelwa. . Iziphene ze-Cosmetic / ezibonakalayo kufuneka zibuyiselwe e-Surenoo phakathi kweentsuku ze-90 zokuthunyelwa. Ukuqinisekiswa kwaloo mhla kuya kusekelwa kumaxwebhu othutho. Uxanduva lwewaranti ye-Surenoo enyiniweyo ekulungiseni kunye/okanye ukutshintshwa kwemigaqo echazwe ngasentla. I-Surenoo ayiyi kuba noxanduva lwazo naziphi na iziganeko ezilandelayo okanye ezilandelanayo.

Umthetho WOKUBUYISA

Akukho waranti inokunikwa ukuba la manyathelo okhuseleko achazwe ngasentla awakhange ahoywe. Ex eqhelekileyoampUlwaphulo-mthetho lu:

• Iglasi yeGraphic eyaphukileyo.
• PCB eyelet yonakele okanye iguqulwe.
• Iikondakta zePCB zonakele.
• Isekethe iguqulwe nangayiphi na indlela, kubandakanywa ukongezwa kwamacandelo.
• PCB tampzenziwe ngokusila, ukukrola okanye ukupeyinta ivanishi.
• Ukuthengisa okanye ukuguqula i-bezel ngayo nayiphi na indlela.

Ukulungiswa kwemodyuli kuya kufakwa kwi-invoyisi kumthengi emva kwesivumelwano. Iimodyuli mazibuyiswe zinenkcazelo eyaneleyo yokusilela okanye iziphene. Naziphi na iziqhagamshelo okanye intambo efakwe ngumthengi kufuneka isuswe ngokupheleleyo ngaphandle kokonakalisa i-eyelet ye-PCB, ii-conductors kunye neetheminali.

UKUNXUMA UMFANEKISO

Yintoni ukuncamathela koMfanekiso?

Ukuba uhlala ungumfanekiso oqingqiweyo kwiSiboniso seMzobo ixesha elide, unokufumana isenzeko esibizwa ngokuba yi-Image Sticking. Ukuncamathelisa komfanekiso - ngamanye amaxesha okukwabizwa ngokuba "ukugcina umfanekiso" okanye "isiporho"- yinto apho ulwandlalo olufiphele lomfanekiso oboniswe ngaphambili luhlala lubonakala kwiscreen xa umfanekiso utshintshwa. Inokuthi yenzeke kumanqanaba aguquguqukayo okuqina ngokuxhomekeke kwimizobo yomfanekiso othile, kunye nobungakanani bexesha izinto zomfanekiso ongundoqo ezivunyelweyo ukuba zihlale zingatshintshwanga kwisikrini. Kwizicelo zePOS, umzekeloampLe, imenyu yeqhosha elihlala lilungisiwe, okanye apho izinto "zesakhelo" (umfanekiso ongundoqo) zihlala zingatshintshi kwaye amaqhosha anokutshintsha, anokuba sesichengeni sokuncamathela komfanekiso. Kubalulekile ukuqaphela ukuba isikrini sisetyenziselwa kuphela esi sicelo, umsebenzisi akanakuze aqaphele le nto kuba isikrini asizange sibonise omnye umxholo. `Kuxa kuphela umfanekiso ongengowomfanekiso "ogciniweyo" uboniswa kwiscreen apho lo mba ubonakala khona. Ukuncamathelisa umfanekiso kwahlukile ukuba isiphumo "sokutshisa-ngaphakathi" siqhele ukunxulunyaniswa nezixhobo ezisekelwe kwiphosphor.

Yintoni ebangela ukuncamathela koMfanekiso?

Ukunamathela komfanekiso kukuziphatha kwangaphakathi kwemiboniso ye-Graphic ngenxa yokuba sengozini kwi-polarization yezinto zangaphakathi (iikristali ezimanzi) xa zisetyenziswe phantsi kweemeko ezimileyo, ezihlawuliswayo (ngokuqhubekayo ukubonisa umfanekiso ofanayo). Iikristale zolwelo zomntu ngamnye kwiphaneli yoMzobo zineempawu zombane ezizodwa. Ukubonisa ipateni esisigxina - njengemenyu ye-POS echazwe ngasentla - kwixesha elide kunokubangela ukwakhiwa kwentlawulo ye-parasitic (i-polarization) ngaphakathi kweekristale zolwelo ezichaphazela iipropathi zekristali ze-optical kwaye ekugqibeleni zithintele ikristale yolwelo ukuba ibuyele kwisiqhelo sayo, ukuphumla xa iphethini itshintshiwe ekugqibeleni. Esi siphumo senzeke kwinqanaba leeselula ngaphakathi kwePhaneli, kwaye umphumo unokubangela ukulungelelaniswa kwe-crystal ehlawulisiweyo ezantsi okanye phezulu kweseli ye-crystal kwi-"z" axis, okanye ukufuduka kwekristale ukuya kwimida yeseli, kwakhona ngokusekelwe polarity yabo. Ezi meko zinokubangela ukuba umfanekiso unamathele kwindawo yonke, okanye kwimida yokutshintsha kombala ohlukileyo ngokulandelelanayo. Kuyo nayiphi na imeko, xa iikristale zolwelo kwiipixels kunye nee-pixels ezincinci ezisetyenziselwe ukubonisa umfanekiso omileyo zenziwe zahlukaniswa kangangokuba zingakwazi ukubuyela ngokupheleleyo kwimeko yazo "ezolile" xa zicinywa, isiphumo sisiba ngumfanekiso otyhafileyo, obonakalayo, ogciniweyo. indawo yolawulo ekunikezelweni komfanekiso omtsha, owahlukileyo. Olona qondo logcino lomfanekiso luxhomekeke kwizinto ezahlukeneyo ezifana nomfanekiso othile, ixesha elingakanani uboniswa ungatshintshanga, ubushushu ngaphakathi kwendawo yolawulo kunye nebhrendi ethile yephaneli ngenxa yeyantlukwano yokuvelisa phakathi kwabavelisi bephaneli.

Ungakunqanda njani ukuncamathela komfanekiso?

• Zama ukungasebenzisi iGraphic ngomfanekiso "osisigxina" kwisikrini ngaphezu kweeyure ezi-2.
• Ukuba usebenzisa imonitha kwindawo yobushushu obuphakamileyo kunye nomfanekiso obonisiweyo ochasene neengcebiso "Kubaphuhlisi beSoftware" ngezantsi, intonga yomfanekiso ingenzeka kwimizuzu engama-30. Lungisa iisetingi zesikrini sakho ngokufanelekileyo.
• Ukunciphisa iyunithi ngexesha elide lokungasebenzi njengeeyure ivenkile evaliweyo okanye ukutshintsha ngexesha apho isixhobo sesixhobo singasetyenziswanga.
• Sebenzisa umgcini wekhusi kunye nemvelaphi emnyama okanye ephakathi engwevu esetwa ngokuzenzekelayo ukuba ivele ukuba isixhobo asisebenzi ngaphezu kwemizuzu emi-5-10.
• Kuphephe ukubeka imonitha kwindawo ekungangeni moya ngazo kakuhle okanye kwiindawo eziya kudala ubushushu obugqithisileyo malunga nemonitha kubaphuhlisi besoftware.
• Ekuchazeni ii-ayikhoni, amaqhosha, okanye iifestile kwikhusi, zama ukusebenzisa iipateni zebhloko endaweni yemigca eyahlukileyo njengemida yokwahlula isiboniso kwiindawo ezahlukeneyo.
• Ukuba kuyimfuneko ukubonisa umfanekiso omileyo, zama ukusebenzisa imibala elinganayo ukuya kumgangatho ongwevu ophakathi kumda wemibala emibini eyahlukeneyo, kwaye utshintshe kancinane umgca wemida kanye ngexeshana.
• Zama ukusebenzisa imibala engwevu ephakathi kwezo ndawo zizakuba namaxesha amade wokubonisa okanye zihlale zimile njengoko ezinye izinto zemenyu zitshintsha.

Ukulungisa njani ukuncamathela komfanekiso?

Ngokungafaniyo neziphumo “zokutshisa-ngaphakathi” ezihlala zingenakuguqulwa ezidla ngokunxulunyaniswa ngokuthe ngqo view Izixhobo zokubonisa i-phosphor ezifana ne-CRTs, umfanekiso ogcinwe kwi-Graphic display unokuguqulwa - ngokuphindaphindiweyo ukuya kwindawo yokungabonakali ngokupheleleyo. Nangona kunjalo, ubuzaza bezizathu ezisisiseko (njengoko kuchaziwe ngasentla) komfanekiso ogcinwe kwisiboniso esithile, kunye nezinto eziguquguqukayo (bona "Abaphuhlisi beSoftware" ngasentla) apho umfanekiso ogciniweyo wenziwa phantsi, uya kuyalela inqanaba lokugqibela. yokubuyisela umva. Enye indlela yokucima umfanekiso ogciniweyo kwiphaneli kukuqhuba isikrini (i-monitor "on") kwipateni "yonke emnyama" kwiiyure ze-4-6. Kukwaluncedo ukwenza oku kwindawo yobushushu obuphezulu obumalunga ne-35º ukuya kuma-50ºC. Kwakhona, ukusebenzisa isigcini sesikrini esiguqukayo esinayo yonke imvelaphi emnyama ngexesha lokubonisa okungenzi nto yindlela elungileyo yokuthintela imiba yokugcinwa kwemifanekiso.

Ngaba ukuncamathela koMfanekiso kugqunywe siSiqinisekiso seSurenoo RMA?

Ukuncamathelisa umfanekiso yinto engokwemvelo kwitekhnoloji yoMzobo wokuBonisa ngokwayo, kwaye ngenxa yoko, ukwenzeka kwesi "ghosting" isiphumo sithathwa njengomsebenzi oqhelekileyo ngabavelisi beemodyuli zokubonisa uMzobo ezidityaniswe kwizisombululo zanamhlanje zokubeka iliso. I-Surenoo ayigunyazisi naluphi na umboniso ngokuchasene nokwenzeka kokuncamathela komfanekiso. Sicebisa ngamandla ukuba ulandele iingcebiso zokusebenza ezidweliswe ngasentla ukunqanda ukwenzeka kwale nto.

Nantso isiphelo sedata.

www.surenoo.com

Amaxwebhu / Izibonelelo

I-Surenoo SLG320240B yoMzobo weModyuli ye-LCD yokubonisa iPhaneli yokuBonisa [pdf] Incwadi yokusebenzisa SLG320240B Iphaneli yoMzobo yeLCD yeModyuli yokuBonisa, SLG320240B, iMizobo yeLCD yeModyuli yokuBonisa iPhaneli yokuBonisa, iModyuli yeLCD yokuBonisa iPhaneli yokuBonisa, iSiboniselo sePhaneli yokuBonisa

Iimbekiselo

• Incwadi yokusebenzisa