I-NICOR H12VSENSOR Sensors Remote Programmer

INGCACISO

Ukunikezwa Amandla	2xAAAA1 5V ibhetri, iAlkaline ikhethwayo
Ityala eliphetheyo	I-RC-100 kwimeko yokuthwala
Unxibelelwano	I-940 nm ye-Infrared Tx & Rx
Uluhlu lokulayisha	Ukuya kuthi ga kwi-15 m (50 ft.)
Op. ubushushu	0°C-50°C (32°F-122°F)
Imilinganiselo	123 x 70 x 20.3 mm (4. 84″ x 2.76″ x 0. 8″)

ISILUMKISO  Susa iibhetri kwikompatimenti ukuba iremowuthi ayiyi kusetyenziswa kwiintsuku ezingama-30.

PHEZULUVIEW

Ulawulo olukude olungenazingcingo Isixhobo soLungiselelo lwe-IR sisixhobo esiphathwa ngesandla soqwalaselo olukude lwe-IR-enabled fixture fixture sensors ezihlanganisiweyo. Isixhobo senza isixhobo ukuba siguqule nge-pushbutton ngaphandle kweeleli okanye izixhobo, kwaye sigcina ukuya kuthi ga kwiindlela ezine zeparamitha yenzwa ukukhawulezisa uqwalaselo lweenzwa ezininzi.
Ulawulo olukude luthumela isethingi yoluvo kwindawo yokunyuka ukuya kuthi ga kwienyawo ezingama-50. Isixhobo sinokubonisa iiparameters zenzwa esekwe ngaphambili, ikopi yeeparamitha kwaye uthumele iiparamitha ezintsha okanye ugcine iparameter profiles. Kwiiprojekthi apho ulungelelwaniso olufanayo lunokufunwa kwiindawo ezininzi okanye izithuba, esi sikhundla sibonelela ngendlela elungelelanisiweyo yoqwalaselo. Iisetingi zinokukotshwa kwindawo yonke, okanye kwiindawo ezahlukeneyo.

IZALATHISI ze-LED

I-LED	INKCAZO	I-LED	INKCAZO
UKUKHANYA	Isiphelo esiphezulu sokujika isitrim umsebenzi (Ukuseta umgangatho wemveliso yokukhanya okuqhagamshelweyo ngexesha lokuhlala)		Ukukhetha ixabiso le-lux elijikelezileyo langoku njengokukhanya kwemini. Eli nqaku lenza ukuba ulungiso lusebenze kakuhle nakweyiphi na imeko yesicelo sokwenyani.
UBUVUMANO	Ukuseta uvakalelo lokuhlala kwiSensom		Isivamvo sokukhanya sasemini siyayeka ukusebenza, kwaye zonke iintshukumo ezichongiweyo zinokuvula isibane sokukhanya, nokuba ukukhanya kwendalo kuqaqambe kangakanani.
IXESHA ELIBAMBIWEYO	Ixesha apho uluvo luyakucima khona (ukuba ukhetha inqanaba lokuma ngu-0) okanye ufiphaze ukukhanya ukuya kwinqanaba eliphantsi emva kokuba indawo iphumile.	YIMA NGEDIM	Ukuseta inqanaba lemveliso yokukhanyisa okudibeneyo ngexesha lesithuba. Inzwa iya kulawula umbane wokukhanyisa kwinqanaba elimiselweyo. Ukuseta inqanaba le-STAND-BY DIM kwi-O kuthetha ukukhanya okugcweleyo ngexesha lesithuba.
ISIZIVA ZEMINI	Ukumela imiqobo eyahlukeneyo yenqanaba lokukhanya kwendalo kwiSensom .	YIMA NGEXESHA	Ukumela ixesha apho uluvo luzakugcina ukukhanya kumphakamo osezantsi mfiliba emva kokuba KUBAMBA IXESHA liphelile.

 

Guqula iisetingi ezininzi zabenzi boluvo nge-smart photocell sensor Vula

1. Cinezela Disp, izikhombisi ezikhokelayo ezikude ziza kubonisa iiparamitha zamva nje.
2. Cinezela UPor PHANTSI ngenisa kwimeko yokumisela, iparameter Izikhombisi ezikhokelwayo zolawulo olukude ziya kudanyaza zikhethwe.
3.  Cinezela , Izalathi ezi-2 ezikhokelayo ziya kudanyaza kwisetingi zokukhanya kwemini, khetha ukukhanya kwemini 10 30 50  njengendawo yokumisela ukukhanya Ngokuzenzekela, khetha ukukhanya kwemini 100 300 500  njengendawo yokukhanyisa ukucima Ngokuzenzekelayo.
4. Cinezela OK ukuqinisekisa lonke useto kunye nokugcina.
5.  Jonga kwi-sensor ekujoliswe kuyo kwaye ucinezele THUMELA ukulayisha iparamitha entsha. Isibane esikhokeleyo apho umenzi woluvo

PHAWULA: ivaliwe ngokungagqibekanga.

1. Vula okanye uvale inzwa yokukhanya emini ngokutyhala xa ulawulo olukude lukwimeko yokumisela.
2. Xa isivamvo sokukhanya sasemini sivula, izibonisi ezi-2 zeLed ziyadanyaza kwisetingi yokukhanya kwemini. khetha ukukhanya kwelanga 10 30 50 njengendawo yokumisela ukukhanya Ngokuzenzekela, khetha ukukhanya kwemini 100 300 500 Njengendawo yokumisela ukukhanyisa ngokuzenzekelayo.Xa isivamvo sokukhanya kwemini sivale, 1 Isalathisi seLed sidanyazi kwisetingi yesivamvo sokukhanya kwemini yokukhetha umda womva wokukhanya wemini.
3. Xa i-sensor yokukhanya kwemini ivulekile, ixesha lokuma li-8 kuphela
4. I-Smart daylight sensor ithatha indawo yokutshintsha okuqhelekileyo kwe-sener emini yangaphandle, isebenza ngokuzimeleyo.
5. Jonga uMsebenzi weSensor yeMini.

Umsebenzi weCorridor

Lo msebenzi ngaphakathi kwinzwa yentshukumo ukufezekisa ulawulo lwenqanaba lesithathu, kwezinye iindawo ezifuna isaziso sokutshintsha ukukhanya ngaphambi kokucima. I-sensor inikezela ngamanqanaba e-3 yokukhanya: 100% -> ukukhanya okukhanyayo (ukukhanya kwendalo akwanele) -> cima; kunye namaxesha ama-2 exesha elikhethiweyo lokulinda: ixesha lokubamba isindululo kunye nexesha lokulinda; Ubume bemini obukhethiweyo kunye nendawo yokufumana inkululeko.

• Ngokukhanya kwendalo okwaneleyo, isibane asivuthi xa kubonwa ubukho.
• Ngokukhanya okungonelanga kwendalo, inzwa itshintshela ekukhanyeni ngokuzenzekelayo xa ubukho bufunyenwe.
• Emva kwexesha lokubamba, ukukhanya kuya kuba mnyama ukuya kwinqanaba lokuma ukuba ukukhanya kwendalo okujikelezileyo kungaphantsi komda wokukhanya kwemini.
• Ukukhanya kuzicima ngokuzenzekelayo emva kokuphela kwexesha lokuma.

Umsebenzi woVavanyo lweMini

Vula inzwa yokukhanya kwemini ngokutyhala xa ulawulo olukude lukwimeko yokumisela.

• Ukukhanya kutshintsha kwi-100% xa kukho intshukumo efunyenweyo.
• Ukukhanya kuya kuba luzizi ukuya kwinqanaba lokuma emva kokubamba ikalika.
• Ukukhanya kuhlala kwinqanaba lobumnyama ebusuku.

Iisetingi kulo mboniso:

• Ixesha lokubamba: 30min
• indawo yokukhanya: 50 lux
• indawo yokucima ukukhanya: 300 lux
• Yima ecaleni Dim: 10%
• Ixesha lokulinda: +oo (xa i-smart photocell sensor ivula, ixesha lokuma lilodwa +oo)

UKUSETYENZISWA KWEBHUNTI

UKUSETHA

I-SETTING Content iqulethe zonke iisetingi ezikhoyo kunye neeparameters ze-remote sensors. Ikuvumela ukuba utshintshe ulawulo olukhoyo, iiparamitha, kunye nokusebenza kwenzwa ukusuka kwi-factory default okanye iparameters zangoku.

Tshintsha useto oluninzi lwe sensor(s)

1. Cinezela Disp iqhosha, iilethi zolawulo olude zizakubonisa iiparamitha zakutsha ozicwangcisayo.
   PHAWULA: ukuba uyatyhala LAYITA ICIMA iqhosha ngaphambili, kufuneka utyhale Ngokuzenzekelayo iqhosha lokuvula umenzi woluvo.
2. CinezelaUP or PHANTSI Ngenisa kwimeko yocwangciso, iparameter ezikhokelayo zolawulo olukude ziyakudanyaza ukuze zikhethwe, jonga kucwangciso olufunwayo ngokucinezela. UP ISALO ESAYINXA EKUNXELENI ukukhetha iiparamitha ezintsha.
3. Cofa u-ok ukuqinisekisa lonke useto kunye nokugcina.
4. Injongo kwi-sensor ekujoliswe kuyo kwaye ucinezele ukulayisha iparamitha entsha, ukukhanya okukhokelwayo apho inzwa idibanisa iya kuvula / icime njengoko kuqinisekiswa.
   PHAWULA: Useto lusebenza inyathelo eliphambili ngu UP or PHANTSI, ngenisa kwimeko yokumisela.
   PHAWULA: Ukukhanya okukhokelwayo apho inzwa yoluvo iqhagamsheleka kuyo kuya kudanyaza/cima ukuqinisekisa ukufumana iiparamitha ezintsha.
   PHAWULA: Ukuba ucinezela Disp iqhosha, izikhombisi ezikhokelayo ezikude ziza kubonisa iparameters zamva nje ezithunyelweyo.

• Xa inqanaba lokukhanya kwendalo lidlula i-setpoint off ukuya ekukhanyeni, ukukhanya kuya kucima nokuba isithuba sigcwele.
• Ukukhanya kuvula ngokuzenzekelayo kwi-10% xa ukukhanya kwendalo kungenakwanela (akukho ntshukumo).

Umsebenzi weCorridor VS uMsebenzi woVavanyo lweMini.

1. ln umsebenzi wepaseji, ulayite isibane KUFUNEKA ngomgangatho wokukhanya kwendalo osezantsi kweseti yokukhanya kwemini kunye nokuHlala. Kumsebenzi wesivamvo sokukhanya sasemini, vula isibane ngomgangatho wokukhanya wendalo osezantsi wokukhanya kwemini ukuze ukhanyise nokuba kukho isithuba.
2. Kumsebenzi wepaseji, cima isibane ngokugqiba kwexesha lokuma ukuba kukho isithuba. Kumsebenzi wesivamvo sokukhanya sasemini, cima isibane ngenqanaba lokukhanya kwendalo ngaphezulu kunendawo yokuseta emini ukucima ngaphambi kokuba ubekhona.
3. ln ukusebenza kwenzwa yokukhanya kwemini, inqanaba lokukhanya kwendalo likhaphukhaphu / lisezantsi kunokukhanya kwemini ukuseta ukucima / ukulayita KUFANELE ugcine ubuncinci umzuzu omnye, oya kucima / ukukhanyisa ngokuzenzekelayo.

Malunga nokuseta FUTHI NEMODE(1,2,3,4) Ulawulo olukude luza ne-4 Scene MODES ezingagqibekanga. Unokwenza iiparamitha ezifunekayo kwaye ugcine njengeMODE entsha (1,2,3,4) ukuqwalasela abenzi boluvo abafakelweyo.

UKUHLAZA: zonke izicwangciso zibuyela umva kuseto lwe-DIP Tshintshela kwisivamvo.

IIINDLELA ZESIQINISEKISO (1 2 3 4)

Isicelo	Ukhetho Lwendawo	Ukuqaqamba	Indawo yokufumanisa	Bamba Ixesha	Ixesha lokuma	St nd-byDim Level	Isivamvo seMini
Ngaphakathi	Indlela1	100%	75%	5min	30min	30
Ngaphakathi	Indlela2	100%	75%	1min	+yho	3
Ngaphakathi	Indlela3	100%	75%	mn	30min	30	30LU
Ngaphandle	Indlela4	100%	75%	1m	+yho		(30LUX/300LUX)

Guqula iiMODE:

1. cofa Imowudi1/iMode2/iMode3/iMode4 iqhosha, ulawulo olukude Izibonisi zeLed zibonisa iiparamitha ezikhoyo.
2. cofa UP ISALO ESAYINXA EKUNXELENI  ukukhetha iiparamitha ezintsha.
3. Cinezela OK ukuqinisekisa zonke iiparamitha kunye nokugcina kwimowudi.

LAPHA Umsebenzi wokulayisha ikuvumela ukuba uqwalasele inzwa kunye nazo zonke iiparameters kumsebenzi omnye. Unokukhetha OKUSEKO iiparamitha okanye iMODE yokulayisha.

Iiparameters zangoku okanye iMODE iboniswe kulawulo olukude . Layisha iparameters zangoku kwi sensor(s), kwaye phinda iparameters zoluvo ukwenza enye ukuya kwenye

1. Cinezela Disp iqhosha okanye cinezela Imowudi1/iMode2/iMode3/iMode4 zonke iiparameters ziboniswa kulawulo olukude.
   Phawula: khangela ukuba zonke iiparamitha zichanekile, ukuba akunjalo, zitshintshe.
2. Jonga kwinzwa kwaye ucinezele Thumela iqhosha , isibane esidityaniswe ngumenzi woluvo siya kuvulwa/cinywe njengoko kuqinisekiswa. Qaphela: ukuba enye inzwa ifuna iiparamitha ezifanayo, jonga nje kwinzwa kwaye ucinezele Thumela iqhosha.

Amaxwebhu / Izibonelelo

I-NICOR H12VSENSOR Sensors Remote Programmer [pdf] Incwadi Yomyalelo I-H12VSENSOR, i-H12VSENSOR i-Sensors Remote Programmer, i-Sensors Remote Programmer, i-Remote Programmer

Iimbekiselo

• Incwadi yokusebenzisa