NICOR H12VSENSOR Sensors Chaw Taws Teeb Programmer

SPECIFICATIONS

Fais fab mov	2 xAAAA 1 5V roj teeb, Alkaline nyiam
Nqa cov ntaub ntawv	RC-100 hauv lub hnab nqa khoom
Kev sib txuas lus	940nm Infrared Tx & Rx
Upload ntau	Mus txog 15 m (50 ft.)
Op. kub	0 ° C-50 ° C (32 ° F-122 ° F)
Qhov ntev	123 x 70 x 20.3 mm (4. 84 "x 2.76" x 0")

CEEB TOOM  Tshem cov roj teeb tawm ntawm qhov chaw yog tias cov chaw taws teeb yuav tsis siv hauv 30 hnub.

TshajVIEW

Cov chaw taws teeb tswj Wireless IR Confiquration Tool yog ib lub cuab yeej siv rau cov chaw taws teeb confiquration ntawm IR-enabled fixture integrated sensors. Lub cuab yeej ua rau cov cuab yeej hloov kho ntawm lub laub khawm yam tsis muaj cov ntaiv lossis cov cuab yeej, thiab khaws cia txog plaub qhov ntsuas ntsuas qhov ntsuas kom nrawm rau kev teeb tsa ntawm ntau lub sensors.
Cov chaw taws teeb tswj xa sensor teeb tsa ntawm qhov siab txog li 50 feet. Cov cuab yeej tuaj yeem tso saib qhov ntsuas ntsuas qhov ntsuas yav dhau los, luam cov ntsuas thiab xa cov ntsuas tshiab lossis khaws cov khoom ntsuas profiles. Rau tej yaam num uas zoo tib yam tej zaum yuav xav tau nyob rau hauv ib tug loj tus naj npawb ntawm cov cheeb tsam los yog qhov chaw, qhov no muaj peev xwm muab ib tug streamlined txheej txheem ntawm configuration. Cov chaw tuaj yeem luam tawm thoob plaws ib lub xaib, lossis hauv ntau qhov chaw.

LED qhia

LED	Kev piav qhia	LED	Kev piav qhia
Kev kaj siab	High kawg trim tig muaj nuj nqi (Tsim cov zis theem ntawm kev sib txuas teeb pom kev zoo thaum nyob)		Txhawm rau xaiv tus nqi tam sim no nyob ib puag ncig lux raws li qhov nruab hnub nrig. Qhov no feature enables lub fixture ua hauj lwm zoo nyob rau hauv tej yam kev thov tiag tiag.
SIJ HAWM	Txhawm rau teeb tsa qhov chaw nyob rhiab heev ntawm lub Sensor		Lub teeb pom kev nruab hnub tsis ua haujlwm, thiab txhua qhov kev txav tau pom tuaj yeem tig rau lub teeb pom kev zoo, txawm tias lub teeb ntuj ci li cas.
TUAJ SIAB	Lub sij hawm uas lub Sensor yuav tua (yog tias koj xaiv stand-by theem yog 0) los yog dim lub teeb mus rau theem qis tom qab qhov chaw so.	STAND-BY DIM	Txhawm rau teeb tsa cov zis theem ntawm kev sib txuas teeb pom kev zoo thaum lub sijhawm tsis muaj haujlwm. Lub sensor yuav tswj cov teeb pom kev zoo ntawm qhov teeb tsa. Kev teeb tsa STAND-BY DIM theem ntawm O txhais tau tias lub teeb puv tawm thaum lub sijhawm tsis muaj.
DAYLIGHT SENSOR	Txhawm rau sawv cev rau ntau qhov pib ntawm lub teeb ci ntuj rau lub Sensor .	YUAV TSUM TAU LUB SIJ HAWM	Txhawm rau sawv cev rau lub sijhawm uas Sensor yuav khaws lub teeb ntawm qis qis tom qab HOLD TIME dhau mus.

 

Hloov ntau qhov chaw ntawm sensors nrog ntse photocell sensor Qhib

1. Xovxwm Disp, tej thaj chaw deb coj ntsuas yuav qhia qhov tseeb tsis.
2. Xovxwm UPor POM nkag mus rau hauv qhov teeb meem, qhov parameter Led ntsuas ntawm cov chaw taws teeb tswj yuav flash tobe xaiv.
3.  Xovxwm , 2 coj qhia yuav flash hauv nruab hnub nrig sensor chaw, xaiv hnub ci 10 30 50 ib  raws li setpoint rau lub teeb rau Automatically, xaiv hnub ci 100 300 500 ib  raws li setpoint kom teeb tawm Automatically.
4. Xovxwm OK kom paub meej tias txhua qhov teeb tsa thiab txuag.
5.  Teem lub hom phiaj sensor thiab nias Xa upload tus tshiab parameter. LED teeb uas lub sensor

CEEB TOOM: yog neeg xiam los ntawm lub neej ntawd.

1. Qhib lossis kaw qhov ntse nruab hnub nrig sensor los ntawm kev thawb thaum lub chaw taws teeb tswj nyob rau hauv qhov teeb meem.
2. Thaum lub hnub ci ntse sensor qhib, 2 Led qhov taw qhia yog flash hauv nruab hnub nrig sensor. xaiv hnub ci 10 30 50 ib raws li setpoint rau lub teeb rau Automatically, xaiv hnub ci 100 300 500 ib Raws li qhov teeb tsa rau lub teeb tawm tsis siv neeg.Thaum ntse nruab hnub nrig sensor kaw, 1 Led qhov taw qhia yog flash kuv lub teeb pom kev nruab hnub rau xaiv hnub ci sensor pib.
3. Thaum lub hnub ci ntse sensor qhib, lub sijhawm sawv ntsug tsuas yog 8
4. Ntse hnub ci sensor yuav siv qhov chaw ntawm ib txwm sab nraum zoov nruab hnub nrig senor hloov, ua haujlwm ntawm nws tus kheej.
5. Saib Hnub Ci Sensor Function.

Txoj Kev Ua Haujlwm

Qhov no muaj nuj nqi hauv cov lus tsa suab sensor kom ua tiav tri-theem tswj, rau qee qhov chaw uas yuav tsum tau hloov lub teeb ceeb toom ua ntej hloov-tawm. Lub sensor muaj 3 theem ntawm lub teeb: 100%–> dimmed lub teeb (natural lub teeb tsis txaus)–> tawm; thiab 2 lub sijhawm ntawm kev xaiv lub sijhawm tos: lub sijhawm tuav lub sijhawm thiab lub sijhawm sawv ntsug; Xaiv lub hnub ci qhov pib thiab kev ywj pheej ntawm kev tshawb pom cheeb tsam.

• Nrog lub teeb ntuj txaus, lub teeb tsis hloov thaum pom pom.
• Nrog lub teeb ntuj tsis txaus, lub sensor hloov ntawm lub teeb tau txais thaum pom pom.
• Tom qab tuav lub sijhawm, lub teeb dims mus rau theem sawv ntsug yog tias lub teeb ci nyob ib puag ncig qis dua qhov nruab hnub.
• Lub teeb switches off cia li tom qab lub sij hawm stand-by elapses.

Hnub Ci Sensor Function

Qhib lub hnub ci sensor los ntawm kev thawb thaum tswj chaw taws teeb nyob rau hauv qhov teeb meem.

• Lub teeb hloov ntawm 100% thaum muaj kev txav mus los.
• Lub teeb dims mus rau theem stand-by tom qab tuav-txiv qaub.
• Lub teeb tseem nyob rau theem dimming thaum hmo ntuj.

Kev teeb tsa ntawm qhov kev ua qauv qhia no:

• Lub sijhawm tuav: 30 min
• setpoint rau lub teeb rau: 50 hli
• setpoint rau light off: 300 hli
• Stand-by Dim: 10%
• Stand-by lub sijhawm: +oo (thaum lub ntse photocell sensor qhib, lub sijhawm sawv ntsug tsuas yog +oo)

Khawm OPERATION

SETTING

SETTING Cov ntsiab lus muaj tag nrho cov chaw muaj thiab tsis muaj rau cov chaw taws teeb sensors. Nws tso cai rau koj los hloov cov kev tswj muaj, tsis muaj, thiab kev ua haujlwm ntawm lub sensor los ntawm lub Hoobkas ua ntej lossis tsis muaj tam sim no.

Hloov ntau qhov chaw ntawm sensor(s)

1. Xovxwm Disp khawm, cov chaw taws teeb tswj leds yuav qhia qhov tseeb tsis tau koj teev.
   CEEB TOOM: yog tias koj thawb ON/OFF khawm ua ntej, koj yuav tsum thawb Auto khawm kom qhib lub sensor.
2. XovxwmUP or POM nkag mus rau hauv qhov chaw teeb tsa, qhov parameter leds ntawm cov chaw taws teeb tswj yuav nyem kom raug xaiv, mus rau qhov xav tau los ntawm nias UP QHOV SAIB XOV XWM RAWS LI xaiv cov tsis tshiab.
3. Nias ok kom paub meej tias txhua qhov chaw thiab txuag.
4. Teem ntawm lub hom phiaj sensor thiab nias rau upload tus tshiab parameter, lub teeb coj uas lub sensor txuas yuav qhib / tawm raws li paub meej.
   CEEB TOOM: Kev teeb tsa ua haujlwm tseem ceeb kauj ruam yog los ntawm UP or POM, nkag mus rau hauv kev teeb tsa.
   CEEB TOOM: Lub teeb coj lub teeb uas lub sensor txuas rau yuav nyem rau / tawm kom paub meej tias tau txais cov kev txwv tshiab.
   CEEB TOOM: Yog koj nias Disp khawm, qhov taw qhia cov chaw taws teeb coj yuav qhia qhov tseeb tsis tau xa tuaj.

• Thaum lub teeb pom kev zoo tshaj qhov teeb tsa tawm mus rau lub teeb, lub teeb yuav tua txawm tias thaum twg qhov chaw nyob.
• Lub teeb cia li tig rau ntawm 10% thaum lub teeb ntuj tsis txaus (tsis muaj lus tsa suab).

Corridor Function VS Daylight Sensor Function.

1. Nyob rau hauv txoj kev muaj nuj nqi, tig lub teeb yuav tsum los ntawm ntuj lub teeb theem qis nruab hnub nrig sensor teeb thiab nyob. Nyob rau hauv ntse nruab hnub nrig sensor muaj nuj nqi, tig rau lub teeb los ntawm ntuj lub teeb theem qis nruab hnub teeb teeb rau lub teeb rau txawm tias tsis muaj.
2. Nyob rau hauv txoj kev ua haujlwm, tua lub teeb los ntawm lub sijhawm ua tiav yog tias tsis muaj. Nyob rau hauv lub hnub ci ntse sensor muaj nuj nqi, tua lub teeb los ntawm ntuj lub teeb theem siab tshaj qhov nruab hnub teeb teeb kom teeb tawm ua ntej yog nyob.
3. Nyob rau hauv lub hnub ci ntse sensor muaj nuj nqi, ntuj lub teeb theem sib dua / qis dua nruab hnub teeb teeb rau lub teeb tawm / on YUAV TSUM khaws tsawg kawg 1 mintue, uas yuav tua / tua lub teeb.

Hais txog RESET thiab MODE (1,2,3,4) Cov chaw taws teeb tswj los nrog 4 Scene MODES uas tsis yog lub neej ntawd. Koj tuaj yeem ua qhov tsis xav tau thiab txuag raws li MODE tshiab (1,2,3,4) txhawm rau teeb tsa cov ntsuas ntsuas.

RESET: txhua qhov chaw rov qab mus rau qhov chaw ntawm DIP Hloov hauv sensor.

SCENE MODES (1 2 3 4)

Daim ntawv thov	Scene Options	Brightness	DetectionArea	Tuav Sijhawm	Stand-by Sijhawm	St nd-byDim Level	Hnub Ci Sensor
Sab hauv	Mod1	100%	75%	5 min	30 min	30
Sab hauv	Mod2	100%	75%	1 min	+oo	3
Sab hauv	Mod3	100%	75%	mn	30 min	30	30 LOJ
Sab nraum zoov	Mod4	100%	75%	1m	+oo		(30LUX / 300LUX)

Hloov MODES:

1. xovxwm Hom 1 / Hom 2 / Hom 3 / Hom 4 khawm, cov chaw taws teeb tswj Led ntsuas qhia cov kev ntsuas uas twb muaj lawm.
2. xovxwm UP QHOV SAIB XOV XWM RAWS LI  xaiv cov tsis tshiab.
3. Xovxwm OK kom paub meej tias tag nrho cov kev txwv thiab txuag hauv hom.

UPLOAD Lub luag haujlwm upload tso cai rau koj los teeb tsa lub sensor nrog txhua qhov tsis ua haujlwm hauv ib qho haujlwm. Koj tuaj yeem xaiv CURRENT SETTING parameters lossis MODE rau uploading.

Cov kev teeb tsa tam sim no lossis MODE tau tshwm sim hauv Chaw Taws Teeb. Upload tam sim no tsis mus rau sensor(s), thiab duplicate lub sensor tsis ua ib tug rau anther

1. Xovxwm Disp khawm lossis nias Hom 1 / Hom 2 / Hom 3 / Hom 4 tag nrho cov parameter yog tso tawm nyob rau hauv tej thaj chaw deb tswj.
   Nco tseg: xyuas yog tias tag nrho cov tsis raug, yog tias tsis yog, hloov lawv.
2. Teem lub sensor thiab nias Xa khawm, lub teeb uas sensor txuas yuav qhib / tawm raws li paub meej. Nco tseg: yog tias lwm lub sensor xav tau tib yam tsis muaj, tsuas yog tsom ntawm lub sensor thiab nias Xa khawm.

Cov ntaub ntawv / Cov ntaub ntawv

NICOR H12VSENSOR Sensors Chaw Taws Teeb Programmer [ua pdf] Phau ntawv qhia H12VSENSOR, H12VSENSOR Sensors Tej thaj chaw deb Programmer, Sensors Chaw taws teeb Programmer, Chaw taws teeb Programmer

Cov ntaub ntawv

• Cov neeg siv phau ntawv