NICOR H12VSENSOR Sensor Remote Programmer

MFUNDO

Magetsi	2xAAA1 5V betri, Alkaline amakonda
Kunyamula mlandu	RC-100 m'thumba
Kulankhulana	940 nm Infrared Tx & Rx
Lowetsani osiyanasiyana	Mpaka 15 m (50 ft.)
Op. kutentha	0°C-50°C (32°F-122°F)
Makulidwe	123 x 70 x 20.3 mm (4. 84" x 2.76" x 0")

CHENJEZO  Chotsani mabatire m'chipinda ngati cholumikizira sichidzagwiritsidwa ntchito m'masiku 30.

ZATHAVIEW

Chida chowongolera chakutali cha Wireless IR Confiquration Tool ndi chida cham'manja chosinthira kutali ma sensor ophatikizidwa a IR. Chidachi chimathandizira kuti chipangizochi chisinthidwe kudzera pa batani la pushbutton popanda makwerero kapena zida, ndikusunga mpaka mitundu inayi ya sensor kuti ifulumizitse kasinthidwe ka masensa angapo.
Kuwongolera kwakutali kumatumiza sensa yokhazikika pamtunda wokwera mpaka 50 mapazi. Chipangizocho chimatha kuwonetsa magawo a sensor omwe adakhazikitsidwa kale, kukopera magawo ndi kutumiza magawo atsopano kapena sitolo ya parameter profiles. Kwa ma projekiti omwe makonda ofanana amatha kufunidwa m'malo ambiri kapena malo ambiri, lusoli limapereka njira yosinthira masinthidwe. Zokonda zitha kukopera patsamba lonse, kapena patsamba lina.

ZIZINDIKIRO ZA LED

LED	DESCRIPTION	LED	DESCRIPTION
KUWALA	High end trim turning function (Kukhazikitsa mulingo wotuluka wa kuyatsa kolumikizidwa mukakhala)		Kuti musankhe mtengo wamtengo wapatali waposachedwa ngati polowera masana. Izi zimathandizira kuti pulogalamuyo igwire bwino ntchito zilizonse zenizeni.
KUGWIRITSA NTCHITO	Kukhazikitsa kukhudzika kwa Sensor komwe kumakhalapo		Sensa yamasana imasiya kugwira ntchito, ndipo mayendedwe onse omwe apezeka amatha kuyatsa chowunikira, ngakhale kuwala kwachilengedwe kukuwala bwanji.
NTHAWI YOPHUNZIRA	Nthawi yomwe Sensor idzazimitsa (ngati mutasankha mulingo woyimilira ndi 0) kapena kuyimitsa kuwala mpaka pamlingo wocheperako malowo atachotsedwa.	IMANI-BY DIM	Kukhazikitsa linanena bungwe mlingo wa chikugwirizana kuyatsa pa ntchito. Sensor idzawongolera kutulutsa kowunikira pamlingo wokhazikitsidwa. Kukhazikitsa mulingo wa STAND-BY DIM pa O kumatanthauza kuwala kodzaza ndi nthawi yomwe palibe ntchito.
ZOPHUNZITSA ZA DAYLIGHT	Kuyimira magawo osiyanasiyana a mulingo wa kuwala kwachilengedwe kwa Sensor.	IMANI-NTHAWI	Kuyimira nthawi yomwe Sensor imasunga kuwala kuti pirire pang'ono pakadutsa HOLD TIME.

 

Sinthani masinthidwe angapo a masensa okhala ndi smart photocell sensor Open

1. Press Disp, zizindikiro zotsogolera zakutali zidzawonetsa magawo atsopano.
2. Press UPor PASI lowetsani momwe mungakhazikitsire, chizindikiro cha LED chowongolera chakutali chidzawunikira kuti chisankhidwe.
3.  Press , Zizindikiro za 2 zotsogola zidzawunikira pakasinthidwe ka sensor ya masana, sankhani masana 10 30 50  monga poyambira kuyatsa Zokha, sankhani masana 100 300 500  monga chokhazikitsira kuzimitsa Automatically.
4. Press OK kutsimikizira zoikamo zonse ndi kusunga.
5.  Yang'anani pa sensor yomwe mukufuna ndikusindikiza TUMIZANI kuti mukweze parameter yatsopano. Kuwala kotsogolera komwe sensor

ZINDIKIRANI: imayimitsidwa mwachisawawa.

1. Tsegulani kapena kutseka sensa yanzeru yamasana ndikukankha pamene chiwongolero chakutali chili mu chikhalidwe.
2. Chidziwitso chanzeru chamasana chikatsegulidwa, zizindikiro za 2 Led zimawunikira pakuyika kwa sensor ya masana. kusankha usana 10 30 50 monga poyambira kuyatsa Zokha, sankhani masana 100 300 500 monga setpoint kuzimitsa basi.Pamene smart daylight sensor close, 1 Led chizindikiro ndi kung'anima ndi masana kachipangizo kachipangizo kusankha masana kachipangizo kolowera.
3. Sensor yanzeru yamasana ikatsegulidwa, nthawi yoyimilira ndi 8 yokha
4. Smart masana sensor imachitika panja panja panja, imagwira ntchito palokha.
5. Onani Ntchito ya Daylight Sensor.

Ntchito ya Corridor

Izi zimagwira ntchito mkati mwa sensa yoyenda kuti mukwaniritse kuwongolera kwamagawo atatu, m'malo ena omwe amafunikira chidziwitso chosinthira kuwala musanazimitse. Sensa imapereka milingo ya 3 ya kuwala: 100% -> kuwala kwachilengedwe (kuwala kwachilengedwe sikukwanira) -> kuzimitsa; ndi 2 nthawi ya nthawi yodikira yosankhidwa: nthawi yogwira ntchito ndi nthawi yoyimilira; Chosankha cha masana ndi malo ozindikira.

• Ndi kuwala kokwanira kwachilengedwe, kuwalako sikumayatsa pamene kupezeka kwadziwika.
• Ndi kuwala kosakwanira kwachilengedwe, kachipangizo kameneka kamayatsa kuwala kokha pamene kupezeka kwadziwika.
• Pambuyo pa nthawi yodikirira, kuwalako kumachepa mpaka kuima-pang'ono ngati kuwala kwachilengedwe kozungulira kuli pansi pa masana.
• Kuwala kumangozimitsa nthawi yoyimilira ikadutsa.

Ntchito ya Daylight Sensor

Tsegulani sensa yamasana ndikukankha pamene chiwongolero chakutali chili mu chikhalidwe.

• Kuwala kumayaka pa 100% pakapezeka kusuntha.
• Kuwalako kumachepa kuti muyime-pang'ono pambuyo pa laimu.
• Kuwala kumakhalabe mu dimming level usiku.

Zokonda pachiwonetserochi:

• Nthawi yodikira: 30 min
• setpoint kuyatsa: 50lux
• kukhazikitsa kuzimitsa: 300lux
• Stand-by Dim: 10%
• Nthawi yoyimilira: +oo (pamene chojambulira chanzeru cha photocell chimatsegulidwa, nthawi yoyimilira ndi +oo)

NTCHITO YA BATANI

KUKHALA

Zomwe SETTING zili ndi zosintha zonse zomwe zilipo ndi magawo a masensa akutali. Zimakuthandizani kuti musinthe zowongolera zomwe zilipo, magawo, ndi magwiridwe antchito a sensa kuchokera ku fakitale kapena magawo apano.

Sinthani makonda angapo a sensa (ma)

1. Press Disp batani, zowongolera zakutali ziwonetsa magawo aposachedwa omwe mwakhazikitsa.
   ZINDIKIRANI: ngati mukukankha ON/WOZIMA batani kale, muyenera kukankha Zadzidzidzi batani kuti mutsegule sensor.
2. PressUP or PASI lowetsani momwe mungakhazikitsire, ma parameter owongolera akutali adzawunikira kuti asankhe, yendani kumalo omwe mukufuna ndikusindikiza UP MUVI WA PAMSI KULAMzere Kumanzere kusankha magawo atsopano.
3. Dinani chabwino kuti mutsimikizire zosintha zonse ndikusunga.
4. Yang'anani pa sensa ya chandamale ndikusindikiza kuti muyike parameter yatsopano, kuwala kotsogolera komwe sensor imalumikiza idzayatsa / kuzimitsa monga kutsimikizira.
   ZINDIKIRANI: Zosintha zimagwira ntchito poyambira UP or PASI, lowetsani momwe mungakhazikitsire.
   ZINDIKIRANI: Kuwala kotsogozedwa komwe sensor imalumikizanako kumawunikira / kuzimitsa kuti kutsimikizire kulandira magawo atsopano.
   ZINDIKIRANI: Ngati musindikiza Disp batani, zizindikiro zotsogolera zakutali zidzawonetsa magawo aposachedwa omwe adatumizidwa.

• Kuwala kwachilengedwe kukakhala kopitilira muyeso wowunikira, kuwalako kumazimitsa ngakhale malowo atakhala.
• Kuwala kumangoyatsa 10% kuwala kwachilengedwe kukakhala kosakwanira (palibe kuyenda).

Corridor Function VS Daylight Sensor Function.

1. ln corridor function, kuyatsa kuwala KUYENERA ndi kuwala kwachilengedwe kutsika kwa sensor masana ndi Kukhala. Mu ntchito yanzeru yowunikira masana, yatsani nyaliyo ndi mulingo wachilengedwe wocheperako masana kuti iwunikire ngakhale pali mwayi.
2. Mu corridor function, zimitsani kuwala pomaliza nthawi yoyimilira ngati pali munthu. Mukamagwiritsa ntchito sensor ya masana, zimitsani nyaliyo ndi mulingo wachilengedwe wokwera kuposa masana kuti muzimitsa usiku ngati mulipo.
3. ln Smartlight sensor function, mulingo wachilengedwe wopepuka/otsika kusiyana ndi kuyatsa kwa masana kuti kuyatsa/kuyatsa KUYENERA kukhala osachepera mphindi imodzi, zomwe zizizimitsa/kuyatsa zokha.

Za RESET ndi MODE(1,2,3,4) Kuwongolera kwakutali kumabwera ndi 4 Scene MODES zomwe sizosakhazikika. Mutha kupanga magawo omwe mukufuna ndikusunga monga MODE (1,2,3,4) yatsopano kuti mukonze masensa omwe adayikidwa.

SITANI: makonda onse amabwerera ku zoikamo za DIP Switch in sensor.

ZOCHITIKA (1 2 3 4)

Kugwiritsa ntchito	Zosankha pazochitika	Kuwala	DetectionArea	Gwirani Nthawi	Nthawi Yoyimilira	St nd-byDim Level	Sensor ya masana
M'nyumba	Njira 1	100%	75%	5 min	30 min	30
M'nyumba	Njira 2	100%	75%	1 min	+ uwu	3
M'nyumba	Njira 3	100%	75%	mn	30 min	30	30 LU
Panja	Njira 4	100%	75%	1m	+ uwu		(30LUX/300LUX)

Sinthani MODES:

1. atolankhani Mode1/Mode2/Mode3/Mode4 batani, zowongolera zakutali zowongolera zikuwonetsa magawo omwe alipo.
2. atolankhani UP MUVI WA PAMSI KULAMzere Kumanzere  kusankha magawo atsopano.
3. Press OK kutsimikizira magawo onse ndikusunga mumalowedwe.

KULANI Ntchito yotsitsa imakupatsani mwayi wokonza sensa ndi magawo onse mu ntchito imodzi. Mutha kusankha CURRENT SETTING parameters kapena MODE yotsitsa.

Zosintha zapano kapena MODE zikuwonetsedwa mu Remote control. Kwezani magawo apano ku masensa (ma), ndi kubwereza magawo a sensor kuti apange imodzi kupita ku anther

1. Press Disp batani kapena atolankhani Mode1/Mode2/Mode3/Mode4 magawo onse akuwonetsedwa mu Remote control.
   Zindikirani: fufuzani ngati magawo onse ali olondola, ngati ayi, asinthe.
2. Yang'anani pa sensor ndikusindikiza Tumizani batani , kuwala komwe sensa imalumikiza kudzakhala kuyatsa / kuzimitsa monga kutsimikizira. Chidziwitso: ngati sensa ina ikufuna magawo omwewo, ingoyang'anani pa sensa ndikusindikiza Tumizani batani.

Zolemba / Zothandizira

NICOR H12VSENSOR Sensor Remote Programmer [pdf] Buku la Malangizo H12VSENSOR, H12VSENSOR Sensor Remote Programmer, Sensor Remote Programmer, Remote Programmer

Maumboni

• Buku Logwiritsa Ntchito