Triple M 9PEWP Window Protector
Specifications
- Product Name: 9PEWP Window Protector
- Material: Steel Wire Mesh or Aluminium Mesh
- Installation Time: 0 Hours 15 Minutes
- Document Issue: 1, Date: 25/06/2024
Product Usage Instructions
Kit Contents
Before starting the installation, ensure that you have all the necessary components:
- 1 Window Protector – Welded Steel or Alloy Mesh
- 4 M6x40 Counter-sunk Philips Head Screws
- 4 M6 Nyloc Nuts
Tools Required
Make sure you have the following tools ready:
- Cordless Drill
- 6.5mm Drill Bit
- 10mm Socket
- 10mm Spanner
- Ratchet
- Philips Head Screw Driver
Installation Steps
- Step 1: Positioning
Position the window protector to ensure at least 25mm clearance from the headboard while covering as much of the rear window as possible.
If your vehicle has a Third Brake Light, ensure the top of the protector sits 25mm below the bottom of the lamp to avoid blocking it. - Step 2: Fastening
Mark hole locations on the headboard uprights and drill 6.5mm holes. Use M6x40 counter-sunk screws and M6 nyloc nuts for steel wire mesh protectors, and M6x40 bolts for aluminum mesh protectors.
FAQ
Q: Do I need to use power tools for installation?
A: Yes, the installation requires the use of power tools for drilling and fastening.
INSTALLATION INSTRUCTIONS
Installation of this accessory requires the use of power tools. Check that all work practices com-ply with safety standards, wear appropriate clothing and use personal protection equipment.
Please read these instructions carefully before installation, paying special attention to all Notice, Caution & Warning notes. Failure to do so may result in damaged parts or injury to the installer or customer.
Kit Contents
NOTE: CHECK KIT CONTENTS BEFORE COMMENCING FITMENT AND REPORT ANY DISCREPANCIES
| Item | Description | Qty |
| Steel Wire Mesh Window Protector | ||
| 1 | Window Protector – Welded Steel | 1 |
| 2 | M6x40 Counter-sunk Philips Head Screw | 4 |
| 3 | M6 Nyloc Nut | 4 |
| Item | Description | Qty |
| Aluminum Mesh Window Protector | ||
| 1 | Window Protector – Alloy Mesh | 1 |
| 2 | M6x40 Hex Bolt | 4 |
| 3 | M6 Nyloc Nut | 4 |
Tools Required
| TOOLS REQUIRED | |
| Cordless Drill | 6.5mm Drill Bit |
| 10mm Socket | 10mm Spanner |
| Ratchet | Philips Head Screw Driver |
Fastener Torque Table
| Fastener size | Class | Torque |
| M6 | 8.8 | 9 Nm |
SECTION 1—Installation
- STEP 1
Position window protector to allow minimum 25mm clearance from the headboard whilst still covering as much of the rear window as possible.
NOTE: If Vehicle has Third Brake Light
If the vehicle is fitted with a CHMSL (Center High Mounted Stop Lamp) ensure the top of the window protector sits 25mm below the bottom of the lamp. The brake light must not be blocked by the window protector.
Mark the hole locations on the headboard uprights and drill 6.5mm holes.
- STEP 2
Fasten the window protector to the head-board uprights upright using M6x40 counter sunk screws and M6 nyloc nuts.
For alloy mesh window protectors use M6x40 bolts and M6 nyloc nuts.
Documents / Resources
 |
Triple M 9PEWP Window Protector [pdf] Installation Guide 9PEWP Window Protector, 9PEWP, Window Protector, Protector |
