Intex FastFill Electric Pump AP620C Owner's Manual

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT

⚠ WARNING

NEVER PLACE AN INFANT TO SLEEP ON AIR MATTRESSES.
Never introduce any flammable substance into the inflatable airbed, SUCH AS AEROSOL TIRE REPAIR PRODUCTS, as it may ignite or explode.
This is not a toy. Children must not be left unattended when using the airbed.
Keep the storage bag away from babies and children. The storage bag is not a toy. When not in use, fold the bag and put it away out of the reach of children.
Do not walk, stand on or jump on or use the airbed as a trampoline.
Only for domestic use. Only for indoor use. Do not use on or near water. This is not a raft.
Do not set up bed near stairs, doors, sharp edges or breakable objects. Provide adequate space between bed and objects to avoid entrapment.
Make sure the area is flat, smooth, even and free of sharp objects that could puncture the bed.
Keep pets away from the airbed. Pets may puncture the surface of the bed.
Avoid sleeping on the edge of the airbed. Edges produce less support than the middle of the bed.
Do not operate air pump for more than 5 minutes at a time. Let pump cool at least 15 minutes between use.
Unplug electrical power cord when not in use.
Do not obstruct the air passage opening or insert any objects into the air passage opening.
If the AC supply cord is damaged, it must be replaced by the manufacturer or its service agent or similarly qualified persons in order to avoid a hazard.
To reduce the risk of electric shock, do not expose to rain. Store indoors.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

FOLLOW THESE RULES AND ALL INSTRUCTIONS TO AVOID SUFFOCATION, PROPERTY DAMAGE, ELECTRIC SHOCK, BURNS OR OTHER INJURY.

SAVE THESE INSTRUCTIONS

INSTRUCTIONS

General

No air pump maintenance is required.
Recommended working pressure: 0.025bar (0.36psi).
The appliance must be positioned so that the plug is accessible.
For cleaning use only mild soapy solution. Do not use any chemicals.
In case of repairs, use only common PVC repair glue and patches.

CAUTION

In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

PARTS REFERENCE

Diagram Description: The diagram shows the electric pump with numbered parts. Part 1 is the AC line cord. Part 2 is the switch. Part 3 is the inflation mark (indicated by a symbol resembling a triangle). Part 4 is the off mark (indicated by a symbol resembling a square or circle). Part 5 is the deflation mark (indicated by a symbol resembling an inverted triangle). Part 6 is the air passage. Part 7 is the cord compartment. Part 8 is the cord compartment cover. Part 9 is the inflation valve and valve cap. Part 10 is the airbed itself.

Part Descriptions:

1. AC line cord
2. Switch
3. Inflation mark (symbol: [Inflation Mark])
4. Off mark (symbol: [Off Mark])
5. Deflation mark (symbol: [Deflation Mark])
6. Air passage
7. Cord compartment
8. Cord compartment cover
9. Inflation valve & valve cap
10. Airbed

NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale. Due to a policy of continuous product improvement, Intex reserves the right to change specifications and appearance, which may result in updates to the instruction manual, without notice.

INFLATION

Plug in the AC line cord into an AC electrical outlet. See Fig (1). Fig (1) shows two voltage options: 220-240 V and 110-120 V.
Slide the switch left to the [Inflation Mark]. See Fig (2). Fig (2) illustrates the switch being moved to the inflation position.
When the airbed is fully inflated to the desired firmness, slide the switch right to the [Off Mark]. See Fig (3). Fig (3) shows the switch in the off position.
Lie down on the airbed to test the firmness.
If the sleeping surface is too hard, adjust the firmness by slowly sliding the switch right to the [Deflation Mark]. See Fig (4). Slide the switch left to the [Off Mark] when the desired firmness is achieved. See Fig (5). If the airbed becomes too soft, repeat step #2 thru #5 as necessary. Fig (4) shows the switch moving towards the deflation mark. Fig (5) shows the switch moving back to the off mark.
Disconnect the AC line cord from the wall socket, place it inside the cord compartment.

IMPORTANT
Never disconnect the power line cord from the electrical outlet while the pump is operating. Switch [Off Mark] the pump first before disconnecting the power line cord.

IMPORTANT NOTE on Airbed Inflation

The ambient temperatures of air have an effect on the airbed internal pressure. At low ambient temperature, the air will contract within the airbed and the airbed will feel softer; add air as necessary. At high ambient temperature, the air within the airbed will expand significantly and the airbed will become hard and may burst; release air to avoid damage to the airbed or to soften the feel. Do not expose the airbed to extreme temperatures (hot or cold). Stretching is a natural characteristic of new vinyl. During initial use, the airbed may become soft and require additional inflation to maintain desired firmness. This is normal for the first few days of use. Dimensions shown are approximate and will vary due to the vinyl temperature and the air temperature.

In no event shall Intex, their authorized agents or employees be liable for damages (such as pin holes) to the airbed caused by negligence, ordinary wear and tear, abuse and carelessness, or external forces.

DEFLATION

Plug in the AC line cord into an AC electrical outlet. See Fig (1).
Slide the switch right to the [Deflation Mark]. See Fig (6). Fig (6) shows the switch moved to the deflation position.
When the airbed is completely deflated, begin rolling the airbed from the foot of the airbed towards the head of the airbed where the pump is located. See Fig (7). Fig (7) illustrates rolling the airbed.
When all air is removed from the airbed, slide the switch left to the [Off Mark]. See Fig (3).
Disconnect the AC line cord from the wall socket, place it inside the cord compartment.

INFLATION OPTION (Manual Pump)

If electrical power is not available, a conventional foot or manually operated air pump can be connected to the inflation valve. See Fig (8).
Make sure the switch is in the [Off Mark] position. This will prevent air from escaping from the air passage hole during inflation.
Open the cord compartment cover and pull out the inflation valve cap. Insert the air pump nozzle into the inflation valve to inflate the airbed.
When the airbed is fully inflated to the desired firmness, remove the air pump nozzle, replace the inflation valve cap and close the cord compartment cover.

Note: Inflate only with a low pressure inflator. Do not over inflate. Fill with cold air only.

STORAGE INSTRUCTIONS

Deflate the airbed following the “DEFLATION” instructions.
Make sure the airbed is clean and dry.
Lay the airbed flat with the sleeping surface facing upwards and follow the folding steps on Figs (9 - 13). Fold the airbed loosely and avoid sharp bends, corners, and creases which can damage the airbed. Figs (9-13) illustrate various stages of folding the airbed.
Place the airbed inside the storage bag and store in a dry, cool storage location.

Copyright ©2021 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Recreation Corp. All rights reserved. Printed in China. Trademarks used under license. Distributed in the European Union by Intex Trading B.V. Visit www.intexcorp.com